Professional Documents
Culture Documents
Load Chart of TMS 475 PDF
Load Chart of TMS 475 PDF
SUPERSTRUCTURE
SPECIFICATIONS
ANTI-TWO BLOCK SYSTEMS - fan, swing horn, domelight, dash- valves provide elevation from -6° to
Basic “HAP” is an audio-visual Iight, door and window locks and 2- 76°,
(light/buzzer) warning system to 3/4 lb. (1.3 kg) dry-type fire extin- LATTICE BOOM EXTENSION -
alert operator to an impending two guisher. Complete engine Standard 32 ft. (9.8m) lattice “swing-
block condition combined with instrumentation and crane operat- away” boom extension stows
electronic boom angle display with ing controls, full length control lev- alongside base boom section.
low and high angle preset. Hook- ers, combination hand and foot Boom extension swings into posi-
block or headache ball coming in controls for swing, boom elevation tion; attaches and is held to main
contact with weight suspended and engine throttle, outrigger con- boom nose with four corner pins.
from boom nose switch activates trol panel and sight leveling bubble. *JIB - A 24 ft. (7.32m) A-frame sec-
the audio-visual warning system on MAIN BOOM -34 ft. -116 ft. (10.4m tion which attaches to the sheave
the display panel located within - 35.4m) total length; 3 section shaft of the 32 ft. (9.7m) “swinga-
easy view of operator. trapezoidal main boom consisting way” lattice boom extension. The
*Optional to the basic “HAP’ sys- of base section and 2 full power jib can be offset 5°, 17° and 30°
tem is Krueger “HLAP”. ●HLAP is sections to 84 ft. (25.6m) and a 32 and includes mast, pendant lines,
the same as HAP but further incor- ft. (9.7m) “swingaway” lattice single rope self-equalizing suspen-
porates selective electronic in-cab extension to 116 ft. (35.4 m). sion; stows on right side of carrier
display of boom length in feet and “35 ft. -142 ft. (10.7m - 43.3m) total deck for travel.
meters. length; 4 section trapezoidal main SWING - Planetary drive, 360° con-
*An additional option available to boom consisting of base section, 2 tinuous rotation. Equipped with
all anti-two block systems is Grove full power sections and 1 power Grove “glide swing” with foot acti-
control lever lockout of: hoist up, pinned section to 110 ft. (33.5m) vated multiple disc swing brake for
telescope out and boom down and a 32 ft. (9.7m) “swingaway” lat- precision stopping. Electric/hydrau-
crane functions. tice extension to 142 ft. (43,3 m). lic swing parking brake and two
●LOAD MOMENT AND ANTI-TWO Boom extension is accomplished position hand operated plunger
BLOCK SYSTEM (KRUEGER LMI) by 5-1/2 in. (139.7mm) diameter travel lock. ●Hand operated 360°
- A load moment indicating and bore double-acting telescope positive swing lock controlled from
anti-two block system with audio- cylinders with integral holding operator cab is available. Swing
visual warning and control lever valves. circle bearing is bolted to super-
lockout of: hoist up, telescope out structure and carrier.
BOOM NOSE - Four 15 in.
and boom down crane functions. (381 mm) tread diameter sheaves COUNTERWEIGHT - Removable,
Dash mounted console displays mounted on tapered roller bearings. pin mounted to turntable, power
relative load moment and also pro- Two floating idler sheaves 15 in. installed and removed, hydraulically
vides operator with selective elec- (381 mm) tread diameter mounted extended to working position and
tronic display of boom length in on bronze bushings. Removable pin retracted to stowed or travel posi-
feet and meters, and boom angle in type rope guards. tion. (Weight varies according to
degrees. Angle indicator has high machine specifications).
●18 in. (457mm) sheaves available
and low “presets” with audio-visual MISCELLANEOUS SUPER-
for export requirements.
warning system. STRUCTURE STANDARD
●AUXILIARY BOOM NOSE - Single
CAB - One man, full vision, all steel EQUIPMENT - Hydraulic test panel.
15 in. (381mm) tread diameter
with acoustical treatment and tinted ‘mounted to the main boom nose MISCELLANEOUS SUPER-
safety glass throughout; hinged (removable) for single line work. STRUCTURE OPTIONAL EQUIP-
tinted skylight, sliding left side door Removable pin type rope guards. MENT - Trailing boom kit (less
and sliding right side window for ●18 in. (457mm) sheave available dolly), dual base boom mounted
ventilation. Fully adjustable deluxe for export requirement. floodlights, air conditioning, 360°
fabric seat with headrest and seat- cab spotlight, electric skylight
belt, diesel or propane heater and BOOM ELEVATION - Dual double- wiper.
hot air defroster, electric windshield acting 11 in. (279.4 mm) bore t%bnted Gfove feature or pafent pending.
wiDer and washer. circulating air cylinders with intearal holdina “Denotes options/ equipment.
HOIST SPECIFICATIONS
DESCRIPTION: Sertes parallel circuttryand two motors provide both high Iinepull and speed ranges. Power upanddown, equal Speed, planetary reduction
with integral automat!c brake plUS electronic hoist drum rotation indicator.
’’.”.
. .. . . . . . . .
., . . .+.
?,
. ..
-+? i .- ..--. f~ ..- ++’!
. .
‘
. . .
,:-,
. .. ..
./,.
,,, ..
...,-~.
J .%?< ~...L..
..
<-.+.
-.,.,.
. . ..: ,
..
~ .
. .
-,’,...
.=.
.,.’”
. + ?, , -?------ ,- :.. ”,”. +-1-.
~.... . ... . . .. . . .. ...+
,;a. .::~ ~
ENGINE SPECIFICATIONS
MAKE & MODEL Detroit Diesel 6-71 N ●Cummlns NTCC240
DISPLACEMENT 426 cu. in. (6982 cmJ) 855 cu. in. (14,013 cm])
NOTE: Performance based on 75,000 lb. (34,473 kg) GVW and standard SAE engine rating
conditions using standard tires, transmissions and axles. Performance data may vary plus
or minus 100/odue to variations in engine performance and vehicle weights.
“Denotes optional equipment.
-
DIMENSIONS
TAILSWING -120 In. (3048) retracted counterweight
144 in. (3657) extended counterweight
in. (432)
t
t
I 72 In. (1829)
REAR TRACK
81 7/8 In. (2080)
-1
(229)
-r
- ,FRONT TRACK -
+ 10:tl;:in.
B
@ GmVE MANUFACTURING COMPANY
Otwston01 K!dde Inc
KIDDE
Shady Grove, Pennsylvania 17256-0021
@ROVE
Constant improvement and engineering progress makes it necessary that we reserve the right
to make specification, equipment, and price changes without notice. Illustrations shown may
include optional equipment and accessories and may not include all standard equipment.
170,
I ‘. AC--s” ! I :! I Notes For Lifting Capacities
165
I 60
:, 1. Do not exceed any rated lifting capacity.
155 \\ I ) -1 Rated lifting capacities are based on freely
150 suspended loads with the machine leveled
and standing on a firm supporting surface.
145 Ratings with outriggers are based on
outriggers being extended to their
140 maximum position and tires raised free of
crane wefght before extending the boom or
135 ~,1+++++
lifting loads.
130 2. Practical work{ng loads for each particular
job shall be established by the user
125 depending an operating condition to
include: the supporting surface, wind and
120 other factors affecting stability, hazardous
surroundings, experience of personnel,
handling of load, etc. No attempt must be
made to move a load horizontally on the
5
ground In any direction.
J- 3. Operating radius is the horizontal distance
3 tt. 6 4“.
frOr’I’I the axis of rotation before loading to
the centerline of the vertical hoist line or
tackle with loads aolzlied.
4. /14 ..-.m,tted) de~end~
5.
WTl+i ‘{t:inc4\
—
m \
6.
om angle.
.-.. ”..-..
op.-.
any
hereon.
boom
+;--
is
1.
. . ..Qt
.. .
conditions . ‘..+-*
Handling
not
intended
““..,”. A-
of
authorized
“.
‘f
parsonnel
Or approved
those
from
except
shown
for
the
with
!z’\J-
esfuipment furnished and installed by Grove
Manufacturing Company.
7. For clamshell or concrete bucket operation,
—,’ weight of bucket and load rS’IuSt not exceed
80% of rated lifting capacities.
8. Power-telescoping boom sactlons must be
extended equally at all times. Long
cantilev er booms can create a tipping
conditic Dn when in extended and lowered
position.
9. The maximum load wliich may be
telescoped is limited by hydraulic pressure,
boom angle, boom -.. . .--. .-.
l,,h.{-=+l~n,
,u ate. It Is safe
.1-.. ””- .“” load within the
10.
52!! 11.
not
. . ... ---- ----
raising of load–i with boom lift cylinders
be ~ossibl le. Osieratlonal
may
safety is not
OPERATING RADIUS FROM AXIS OF ROTATION IN FEET Z’Axis OF RoTA71m6 affected by this condition.
C6-829-001 S17 Rtiv. 2 12. Keep load handling devices a minimum of
12 inches (30 cm) below boom head when
lowering or extending boom.
13. If actual boom iength and/or radius is
between values listed, use Iiftlng capacity
fOr. the next longer rated length and/or
I HOOlt
WEIGHT
ELOCKS
45 Ton 4-Sheave . . . .... m
REDUCTION FOR LOAD HANDLING
700 Ibs.
I
DEVICES
14.
15.
-J
15 Ton l-Sheave . . . . . . . . 3101bs.
Auxiliary Boom Head
18 in. Root Sheaves . . . . 220 Ibs.
15 in. Root Sheaves . . . . 190 Ibs.
5 Ton Headache Ball . . . . . . 150 Ibs.
7VZ Ton Headache Ball . . . . . 300 Ibs. tReduction of main boom capacities.
10 Ton Headache Ball . . . . . 500 Ibs. ttReductiorI of 32 ft. Ext. capacities.
m
@!Es!9
@l
GROVE MANUFACfURING COMWiNY
Otivmon0( KsdaeInc
lam
z 55+
Pin. Fly Ext. Ext.
E
in [Power I inned FI r Retracted) & 85 ft. & a5 ft. &l loft. in
Feet *35 40 45 55 65 75 85 110 117 142 Feet ●35 4C
10 100,000 74,000 72,000
See see See
10 100,000 74,(
Warnlrrg Warning Warning
(71) (73.5) (75,5) Note 5 Note 6 Note 7 (71) (73
12 90,000 70,000 67,500 64,000 12 90,000 70 ,[
67.5) (70.5) (73) (76.5) I
(67.5) (70.
15 72,000 63.700 61,000 55,000 44,700 15 72,000 63,;
62.’5 (66 (73) (76) (62.5) (66)
&
3
20 53,000 52,200 44,000 37,900 35,000 31,000 20 53,000 52,2
52.5 57.5 (67.5) (71 .5) (74) (76.5) (52.5) (57.
&
25 38,630 38,630 36,300 31,900 29,200 27,500 20,000 17,500 25 39,150 39,1
(41 .5) (48.5) (5;) 61.5 (66.5) (70) (73) (77) (76.5) (41.5) (48.
L
30 27,010 27,010 27,010 27,010 27,000 25,000 23,900 I 7,700 16,400 30 27,300 27,:
(26) (38) (46) (55.5) 61.5 (69) (75) (74.5) (26) (38)
35 9,610 19,610 19,610 L ,6 0 %’& 19,610 15,200 14,100 9,600 35 20,5
(23.5) (36) (49) (56.5) (61.5) (65.5) (72.5) (72) (77) (23.
40 14,790 14,790 14,790 14,790 14,790 13,200 12,400 8,340 40
(22) (41 .5) (51) (57) (61 .5) (69.5) (69.5) (74.5)
FFF
45 11,770 11,770 11,770 11,770 11,600 11,100 7,540
1
(32.5) (45) (52) (57.5) (66.5) [67) (72.5)
50 9,220 9,220 9,220 9,220 10,300 10,000 6,830
(20) (3a) (47.5) (53.5) (63.5) (64) (70.5)
55 7,540 7,540 7,540 9,200 9,130 6,240 55
(30) (42) (49) (60.5 (61.5) (68)
60 6,010 6,010 6.010 /.916 Tmr 1 5,710 60
(18.5) (35.5) (44.5) (57.5) (58.5) (66)
65 4,720 4,720 6,430 6,490 5,240 65
(28) (39.5) (54.5) (55.5) (63.5)
70 3,680 3,680 5,150 5,210 4,800 70
(1 7.5) (33.5) (51) (53) (61 .5)
75 2,750 4,070 4,130 4,420 75
=+=
% (26,5) (47.5) (49,5) (59)
80 1,920 3,250 3,430 4,070 80
(16.5) (43.5) ~ (56.5)
85 2,590 3,640 ‘ 85
(39.5) (4;.5) (54)
90 1,960 2,270 2,960 90
(35) (38.5) (51.5)
—. 95
95 T3m 1,810 2,350
@Y_ * (49)
100 1,760 100
1
(40) (46)
105 1,090 105
(43)
1 I 1
E
I
115
120
.MS475 IGROVE”
. -142 ft. BOOM FULL HYDRAULIC
*
(POWER PINNED FLY)
PCSA CLASS 10-148
ICARRIER=MOU
CRAN
I LIFTING CAPACITIES IN POUNDS
ON OUTRIGGERS FULLY EXTENDED - OVER REAR
Power 32 ft. 32 ft. Main Boom Length - Feet Power 2 ft. 32 ft.
]Radius I
=1+1 =Ff3
Pin. Fly Ext. Ext. Pin. Fly Ext. Ext.
& 85 ft. &85 ft. &ll Oft. in (Power Pinned Fl~Retracted) & 85 ft. & Es ft. & llo ft.
110 117 142 Feet *35 I 40 I 45 55 I 65 75 I 85 110 117 142
See see Sca
See
Warning
See
warning
Sae
warning
10 109.000 I 74.000 i 72.000 I I Warning Warning Warning
Note 5 Note 6 Note 7 7ij (73.5) (75.5) Note 5 Note 6 Note 7
E
12 90,000 70,000 67,500 64,000
(67.5) (70.5) (73) (76.5)
m
I 1
15 72,0 63.700 61.000 55.000 44.700
62.5)
20 53,000 52,200 49,800 44,000 37,900 35,000 31,000
52.5}
20,000 ‘ 17,500 ‘ 25 39,150 20000 17500
(77) (76.5) (41.5) (7;) (76.5)
17,700 16,400 30 27,300 16.400
(75) (74.5) 26 (38) (46) (55.5) (6i .5) (66) / (69) (75) (74.5)
=l=E
15;200 14,100 9, 00 35 20,900 20,900 20,900 20,900 20,900 15,200 14,100 9,600
(72.5) (72). {77 (23.5) (36) (49) (56.5) (61 3) (72.5) (72) (77)
=
13,200 12,400 8,340 40 16,850 6,850
(69A I (69.5) (74.5) (22) (41 .5) (5i)5 (5;) (6:.5) (6;.5) (7;.5)
11 11,100 7,540 45 13,430 13,430 13,430 13,430 11,600 11,100 7,540
(6 (67) (72.5) (32.5) (45) (52) (57.5) (66.5) (67) (72.5)
10.3UO I i 0.(!00 6,830 50 10,920 10,920 10,920 10,920 10,300 10,000 6,830
tlj~,:\ .- ;) (70.5) (20) (38) (47 .5) (53.5) J63.5) (64) (70.5)
J,~,JC I :,;30 6,240 55 8,930 8,930 8,930 9,200 9,130 6,240
(61.5)
f5i?.i)j (68) (30) (42) (49) (60.5) (61.5) (68)
7910 8030 5,710 60 - 7,330 7,330 7,330 8,250 8,380 5,710
(5;.5) (56.5) (66) (18.5) (35.5) (44.5) (57.5) 58.5 (66)
=E$a
6,430 6,490 5,240 65 5,870 5,870 7,420 7,680 5,240
(54.5) ] (55.5) (63.5) (28) (39.5) 54.5 55.5 63.5
3%
5,150 5,210 4,800 70 4,530 4,53a 6,360 6,400 4,800
(51) (53) (61.5) (17.5) (33.5) (51) (53) (61.5]
4,070 4,130 4,420 75 336 5,29
(47.5) (49.5) (59) (2;.5; (47.5) (4;.:) (5;) 2
3,250 3,430 4,070 80 2,260 4,350 4,460 4,070
(43.5) (46) 56.5) (16.5) (43.5) (46) (56.5)
2,590 2,760 , 40 85 3,650 3,710 3,740
(39.5) (42.5) (54) (39.5) (42.5) (54)
1.960 2.270 2.960 90 3,020 40 344
‘%M%W%-I
(30) 1 (34.5) I 49
95
(35)
2,460
130)
(3i.5)
2,500
(34.5)
(5;.5;
3,160
(49 )
‘=
1,310 1,760 100 1,900 2,070 2,620
(30) (46) (24) (3(I) (46)
1,090 105 1,430 1,720 2,120
(43) (15) (24.5) (43)
110 I ,500 1,730
6-829-001 738D & -O02141B
# (17) (39.5)
115 1,380
(36.5)
I 20 1,040
(32.5)
Note: Boom ●ngles arO in degrees.
A6-829-001732C & -O02141B
0
‘re based
NOTES FOR ON OUTRIGGERS
on structural
=igtit fully extended
strength
as determined
and tipping shouid not be relied upon as a capacity
by test in accordance with SAE-J-765.
Ilmitatlon. Capacities do not
horizontal and the Iongltudinai axis of the boom base section after liftin9 rated load.
..C.%-er pinned fly extended, the rated loads are determined by boom angle in the column headed by 110 ft. boom
.gles not shown, use rating of next lower boom angla.
.cwer pinned fly retracted and 32 ft. boom ext. erected, the rated loads are determined by boom angle Onl Y in the
. angles not shown, use rating of next lower boom angle.
power pinned fly extended and 32 ft. boom ext. erected, the rated loads are determined by boom angle only in
..com angles not shown, use rating of next lower boom angle.
,,
,, ”’.
., :’,
,,
,.,
,,
.,
TMS4-75
35 ft. -142 ft. BOOM
(POWER PINNED FLY)
PCSA CLASS 10-148
t
Main Min. Max.
5° ] 70
Boom 30°
Angle Offset Offset Offset
76° 6,000 5,200 4,600
70 4,300 3,940 3,650
65 3,430 3,200 3,010
60 2.760 2.600 2.470
t 55 I 2;220 I 2;110 i 2;020
A6-S29-001 B23G
-..