Professional Documents
Culture Documents
Training Material of MS06-TW Chassis 20140612041434585 PDF
Training Material of MS06-TW Chassis 20140612041434585 PDF
Training Material of MS06-TW Chassis 20140612041434585 PDF
DVB-T Demo
60Hz 3D
1GBit DDR3
3HDMI(1MHL)
TCON Control
Mini LVDS
Others features:
the motherboard and TUNEL independent design, TUNEL packaging, TUNEL
pluggable, but PCB board integration design.
MS06-TW series
----Menu Display
MS06-TW series
----Menu Display
Interface&Key Components Introduction
Y_IN Power
(U700) Supply LVDS
AV_IN (UD5) SPI FLASH Socket cable
5V to 1.2V(SOC)
Pb_IN
(U801)
Pr_IN SOC (UD4)
12V to 5v To IR
board
Audio L_IN
(YPbPr&AV) Headph To KEY
one out board
Audio R_IN (UD61)
(YPbPr&AV) Audio 5V to DDR1.5V
VGA_IN
Audio Amplifier
To left
HDMI3 (U01A) speaker
MHL Audio
Amplifier To right
speaker
Serial port
Tunner SPDIF
IN output
PCB
板
宽
135mm
PCB板长:195mm
Interface&Key Components Introduction
USB1
LVDS
To KEY cable USB2
board
Power
Supply To IR
Socket board Tunner
(U700)
(U01A) IN
SPI FLASH
Audio
Amplifier
(U801) HDMI1/
To right SOC ARC
speaker
(UD5)
To left
speaker Serial port 5V to 1.2V(SOC) HDMI2/
MHL
Headph
one out
SPDIF
Audio R_IN Audio L_IN Pr Pb Y_IN Audio HDMI3 output
IN IN AV_IN VGA_IN VGA_IN MHL
(YPbPr&AV) (YPbPr&AV)
Interface&Key Components Introduction
Key Components List
Part No. Component Type / Model location
13-AS1117-33B 5V to 3.3V supply IC 3.3V SOT-223 AS1117-33 CX U172
LD1
VDDC1V2
LD61
1V5_DDR
LD3
U172 5V
3V3
Key Test Point
USB 5V
5V
DDR 1V5
MCU_RESET
PANEL VCC_12V
VDDC 1V2
U172
3V3
LD61
1V5_DDR
LD1
VDDC_1V2
LD4
12V
LD4A
5V
Key Test Point
----Power Supply
P101
chassis
power
supplier
When TV set working normally, the voltage of each pin of P101 is like below:
Pin 1/2/4: 24/12V
Pin 3/5/6/9: GND
Pin 7: 3V3
Pin PIN8: 0V(2D mode), 3.3V(3D mode)
Pin 10: 2.8V
Pin 11: Dim signal , 3.17V
Key Test Point
----DC to DC(for MS06B-TW)
Output 12V
24V to 12V
DC to DC
Output 5V
24V/12V to 5V
DC to DC
Key Test Point
----VDDC1.2V
Reference voltage:GND
Input voltage:5V
U172 ouput: 3V3
1] What is the main difference in HDMI1.3, 1.4 & 1.4a?(HDMI 1.4 add follow functions based on V1.3 :HDMI Ethernet
Channel, Audio Return Channel , 3D Over HDMI , support 4K*2K and Micro HDMI etc.. HDMI 1.4a adds 3D formats
based on V1.4: Top and Bottom, Side-by-side Horizontal and some standards.)
Unit Circuit Analysis and Testing
----Backlight and Dim(for MS06B-TW)
Pin 93 of U801 sends out a high or low level, across R104, then directly send to power
board through pin12 of P101 on the main board, control the backlight on or off.
Pin 110 of U801 sends out PWM signal, across R105, then directly sends to power
board through pin11 of P101 on the main board, adjust back light brightness.
Pin 104
of U801
Pin 110
of U801
Pin 93
of U801
Unit Circuit Analysis and Testing
----Backlight and Dim(for MS06B-TW)
AC Input, power board operates and provides a 3V3SB to the main board, TV set enters
standby mode, and the indicator on.
Press the power button of the remote control or the key board to turn on the set, the
Indicator off.
Pin 102 of U801 sends out a high level, then directly send to power board through pin10
of P101 on the main board, control the Power on.
Then the power board output main board power 24V and 24V Invert voltage.
Q711
system reset
test
Unit Circuit Analysis and Testing
----Reset Circuit
1] Explain Timing Waveform relationship ?(as below)
When turn on or off the TV from AC power, the TV will reset to protect the TV. As shown in the pictures.
Picture 1, turn on the TV→3V3SB rises from 0V to 3.3V→CU_RESET rises from 0V to 3.3V and then
drop from 3.3V to 0V. The reset time is 21.9ms. During the reset, CU_RESET with high level was sended
to main chip and initialize the main chip ports. These can make sure our TV can work normally.
Picure 2 shows that when turn off the TV from AC, the TV will reset again.
Unit Circuit Analysis and Testing
1] What is LVDS PW ?(It's the same to LVDS ----LVDS PW
PANEL_VCC. It's the power for Opencell.)
pin 103 of U801 low levelQ701 cuts off, Q700 cuts off PANEL_VCC=0V
pin 103 of U801 high levelQ701 turns on, Q700 turns on PANEL_VCC=12V
PIN 103 of
U801
Unit Circuit Analysis and Testing
1] Amplifier is acually Audio Amplifier ? (Yes,it's) ----Amplifier
2] Red font is not easily visible. (as below)
3] What are the functions of these signals?
C17A:RESET R12A:M_SCL
R11A:M_SDA
Unit Circuit Analysis and Testing
----Amplifier
Pin43: SDA, Pin44:SCL; Pin3/6: Right channel output; Pin7/10: Left channel output.
When the input signal and power supply are normal, but there is no output, you
need to check whether the back-end short-circuit or the amplifier was damaged.
STA381 internal block diagram as below
Unit Circuit Analysis and Testing
----Amplifier
The STA381 is a 20-W, efficient, digital-audio power amplifier for driving stereo bridge-tied speakers.
One serial data input allows processing of up to two discrete audio channels and seamless integration
to most digital dudio processers and MPEG decoders.
I2S, also known as Inter-IC Sound, is an electrical serial bus interface standard used for connecting
digital audio devices together.The bus consists of at least three lines:1.Serial Clock, also named BCLK;
2.Word clock line - also called word select (WS) or left right clock (LRCLK);3.The serial data SDATA.
It may also include the Master clock (typical 256 or 384 x LRCLK).
Red-MCLK(R05A) Orange-BCLK(R06A) Purple-LRCLK(R07A) Green-SDATA(R08A)
MCK(12.3M)=4*BCK(3.07M)=256*LRCK(48.1K)
High-frequency Low-frequency
RC Model:RC330AMI1
Trouble Shooting----No Picture
Trouble Shooting----No Sound
Trouble Shooting----Abnormal Picture
Software update from USB
----Update for Software
一、Factory Update:
1、Copy the software (MERGE.bin) into
USB (root directory);
2、Turn on the TV set.
3、 Insert USB into TV set; (figure 1.2)
4、Turn to Factory MENU, then pitch
on “8-USB_UPDATA’’,
5、 Press OK on the RCU, and select the “Yes”, shown as figure 1.2。
6、Then Enter into User MENU,into Settings->Restore factory settings.
二、User memu Update:
1、Copy the software (MERGE.bin) into
USB (root directory);
2、Turn on the TV set. (figure 1.3)
3、 Insert USB into TV set;
4、Turn to User MENU, choose
Settings->Software Update
5、 Press OK on the RCU,
and select the “Yes”, shown as figure 1.3。
6、Then Enter into User MENU,into Settings->Restore factory settings.
Enter Factory menu & Reset the system
① How to enter in factory menu?