Professional Documents
Culture Documents
Questionaires No. 02 PDF
Questionaires No. 02 PDF
02
5. The Accreditation Board for Engineer and Technology (ABET) is an accrediting agency for:
A. An engineering education program
B. Engineering fundamentals examination
C. Engineering firms
D. All of the above
9. In the figure:
10. Cascade amplifier is used to reduced load effect; the output impedance will be:
A. High
B. Low
C. Medium
D. Zero
12. The CPU architecture shown in the figure below is best described as:
A. Non-pipelined architecture
B. 1-Stage pipeline architecture
C. 2-Stage pipeline architecture
D. Harvard architecture
13. Incandescent lamp will work normally with best efficiency at the power factor is:
A. Unity
B. 0.5 lagging
C. 0.5 leading
D. 0.8 leading
16. A certain communication channel has a signal to noise ratio of 7 and a bandwidth of 10kHz. What is the
channel capacity?
A. 30 bps
B. 80 bps
C. 300 bps
D. 30000 bps
17. Software maintenance activities can be classified into several maintenance types. Which of the
following is not a software maintenance type?
A. Adaptive maintenance
B. Corrective maintenance
C. Customer-initiated maintenance
D. Perfective maintenance
18. An industrial plant is served by a 12470-v delta/480-v grounded-wye transformer. The high voltage side
of the transformer is served from a 12470-v wye-connected distribution line that has a grounded neutral.
The best protection of the transformer against lightning strikes on the 12470-v line will result from surge
arrester connection of:
A. Phase to ground on the 12470-v side of the transformer
B. Phase to phase on the 12470-v side of the transformer
C. Phase to ground on the 480-v side of the transformer
D. Phase to neutral to ground on the 480-v side of the transformer
19. The primary difference between a programmable logic array designated 16R8 and one designated 20
R8 is that the 20 R8 has:
A. Four additional flip flops
B. Four additional input pins
C. Four additional in/out pins
D. 20 pins rather than 16
20. What type of bond guarantees that if a contractor goes broke on a project, the surety will pay the
necessary amount to complete the job?
A. Bid bond
B. Performance bond
C. Acceptance bond
D. Payment Bond
21. The one-line diagram below represents three single phase transformers connected in a delta-wye
arrangement and rated for the line to line voltages indicated. The turns ratio of individual single-phase
transformer is mostly nearly:
A. 2.8
B. 4.8
C. 8.3
D. 14.4
22. An engineer chooses open collector output TTL technology to provide sufficient current to drive a
device. The circuit shown is implemented with a 7405 package and corresponds to the following logic
function (assume that a logic 0 corresponds to 0V).
A. AND
B. NAND
C. OR
D. NOR
24. Which of the following best describes the sequential steps in an Object-Oriented design?
A. Define classes, define interface techniques, define collaboration diagrams, define design diagrams
B. Define use case, define programming language, define interface techniques, define class
C. Define programming language, define class models, define design class diagrams, define
collaboration diagram
D. Define use case, define conceptual model, define collaboration diagrams, define design class
25. Increasing the current withdrawn from a battery has what effect on the battery capacity and why?
A. Increased capacity, which is caused by less internal heat loss
B. Increased capacity, which is caused by lower internal resistance
C. Decreased capacity, which is caused by higher load voltage drop
D. Decreased capacity, which is caused by increased polarization
26. The only load on a 3-phase, 4-wire system is placed between phase B and phase C. The phase to phase
voltage is 13.2kV. The load is 500kVA at 0.85 lagging power factor. The magnitude of the line current
(amperes) in phase C is most nearly:
A. 65.6
B. 55.8
C. 37.9
D. 32.2
29. Which of the following statements best describe show a power transformer’s total losses vary with kVA
load?
A. Losses are linearly proportional to load
B. Losses are proportional to the square root of the load
C. Losses are proportional to the square of the load
D. Losses are proportional to the square of the load plus a constant
30. A power plant uses a turbine-driven synchronous generator rated 3-phase, 150MVA, 13.8kV, 0.85 lagging
power factor. All the rated conditions the power output (MW) is most nearly:
A. 60
B. 75
C. 125
D. 128
35. With respect to relational record-based data models at the user level, a relation is represented in a:
A. Key
B. List
C. Queue
D. Table
36. Which of the following choices is not one of the stages of a project life cycle?
A. Concept
B. Initiation
C. Planning
D. Execution
E. Delivery/Closure
38. For the 4-wire RTD circuit shown, which of the following would case the greatest measurement error in
Vsense?
40. 100 resistors of 100 ohm each connected in parallel. What is the equivalent resistance?
A. 1000 ohm
B. 1 ohm
C. 1/1000 ohms
D. 100 ohms
41. A 3-phase capacitor rated at 240V and 110 kVAR has been proposed for correcting the power factor of a
3-phase induction motor operating at 280 V, the reactive power (kVAR) that will be provided by the
capacitor is most nearly:
A. 82.6
B. 95.3
C. 110
D. 127
42. A series of fuel cells is connected to produce a no-load voltage of 230V at a rated voltage of 300V, the
cells provide 2.0MW to a DC-AC converter. Assuming the cell van be modeled as a standard battery,
what is the total internal resistance of the fuel cells: Hint: (P=V²RL), (P=I²RL)
A. 0.0001
B. 0.003
C. 0.05
D. 3
43. Permanent magnet has a relative permeability that is _________ magnetic material:
A. Higher than
B. Lower than
C. Equal to
D. Not Equal to
44. For effective earthling, which of the following mixture is preferred for filling around the earth electrode?
A. Lime-Sand mixture
B. Saw Dust – Sand mixture
C. Bone Meal mixture
D. Coal-Salt mixture
45. A discrete silicon semiconductor diode is forward biased at 0.75V, what is the approximate current? Hint:
VT = Kt/V, I = Is (eVIbVT – 1)
A. 2.0 mA
B. 3.0 nA
C. 1.5A
D. 3.0 mA
46. For last switching of an NMOS R-pull up inverter (W/L) should be:
A. Large
B. Small
C. Equal to the drain current
D. Equal to the power dissipated during switching
49. While machine in operation, the slip of the synchronous machine is:
A. High
B. Low
C. Zero
D. 1
50. If the induction motor speed at no-load is 745 RPM, what is the speed of the motor?
A. 700 RPM
B. 750 RPM
C. 800 RPM
D. 850 RPM
51. Synchronous speed for motor 1600 RPM, 60hz, Calculate number of poles.
A. P = 2
B. P = 4
C. P = 6
55. A motor is equipped with an optical shaft encoder to measure motor speed. The optical encoder
provides 200 pulses per motor revolution. A microcontroller equipped with a real-time interrupt (RTI)
capability is used to measure motor speed. The RTI interval is 32.768ms. The microcontroller counts 372
pulses from the optical encoder in the RTI interval. The speed (rpm) of the motor is:
A. 33
B. 568
C. 3276
D. 3400
58. A digital signal needs to be modulated and transmitted. If we need to transmit 4 bits, what is the
maximum number of ways it can be transmitted?
A. 2
B. 4
C. 8
D. 16
59. When using Zener Diode in regulator circuits, the output shape will be affected by:
A. Dynamic resistance of the diode
B. Input current passing through the diode
C. Zener Voltage
A. 66kV
B. 132kV
C. 220kV
D. 400kV
62. Which of the transmission voltage is not applied in Qatar Electrical Specifications?
A. 66kV
B. 132kV
C. 220kV
D. 400kV
63. An important step in the software lifecycle is testing. One type of testing is integration testing. Which
of the following is not true concerning integration test?
A. Integration testing is employed to integrate separately tested pieces.
B. In a top-down integration test, testing begins at the top levels to see whether the overall logical
design works and the interfaces between modules are correct.
C. In a bottom up integration test, testing begins first at the lowest level sub-programs. A test driver
is used to set-up the testing environment by declaring and assigning initial values to variables and
then calls the sub-program to be tested.
D. In integration testing, either a top-down or a bottom-up approach is selected to complete the test.
65. The single-phase motor generally used with household ceiling fans is:
A. Split phase type
B. Capacitor start type
C. Permanent Capacitor type
D. None of the above
66. The source voltage in the circuit shown is v= 100sin 377t, the peak reverse voltage applied to the diode
would be:
A. 2.5
B. 100
C. 141.1
D. 31.8
67. All of the following are properties of fuses rather than circuit breakers, with one exception, which item
is the property of circuit breakers?
A. Adjustable time-current characteristics
B. Low initial costs
C. Longer downtime over operation
D. Simplify
68. A phase, 3-wire ungrounded, 13.2kV (phase-to-phase) wye-connected source is connected to a balanced
delta load that is grounded on corner A. The voltage measured between Corner Band ground is most
nearly:
A. Half the Phase-to-phase voltage
B. 7.62 kV
C. 13.2 kV
D. cannot be determined
69. The only load on a 3-phase, 4-wire system is placed between phase B and phase C. The phase-to-phase
voltage is 13.2kV. The load is 500kVA at 0.85 lagging power factor. The magnitude of the line current
(ampere) in phase C is most nearly:
A. 65.6
B. 55.8
C. 37.9
D. 32.2
72. A 3-phase, 60-Hz induction motor has a nameplate speed of 1600 rpm. This motor has how many poles:
A. 2.0
B. 4.0
C. 6.0
D. 8.0
73. Which of the following is a name for a set of indices and values?
A. Array
B. Stack
C. Queue
D. FIFO
74. Your boss has just approved the initiation of a project to celebrate Qatar National Day. Sadia has been
assigned the project manager as should be:
A. Establish the reporting process to the boss
B. Work on the project scope
C. Make a report on required cost for the project
D. Develop the project charter to do the project
E. Ask the boss as to how many team members would be allowed in the project
76. Two resistances R1 and R2 give combined resistance of 4.5 ohms when in series and 1 ohm when in
parallel. The resistances are:
A. 3 ohms and 6 ohms
B. 3 ohms and 9 ohms
C. 1.5 ohms and 3 ohms
D. 1.5 ohms and 0.5 ohms
77. An underground system is built for a military marine system with a normal voltage level. A following
fault analysis design the insulation is most nearly the voltage level for which the insulation on the
distribution system is designed?
A. (1 / √3) A
B. √3) A
C. √2) A
D. 2A
78. The voltage gain of an amplifier with 9% negative feedback is 10. The voltage gain without feedback will
be:
A. 10
B. 1.25
C. 100
D. 90
86. Referring to the figure the voltage V across till: 50-U resistor is:
A. 35
B. 51
C. 71
D. 92
87. The collector region of transistor is doped?
A. Heavily
B. Moderately
C. Lightly
88. A transmitter operating at 23.6GHz has a power output of 20nW. A receiver is located 8miles from the
transmitter (dB) is:
A. 142
B. 124
C. 119
D. 115
90. In HDL Based digital systems the arithmetic multiplication function is difficult to synthesize. Design
solution to this challenge do not include:
A. Sequential generation of partial products
B. Hardware intensive simultaneous generation of partial products
C. Implementation of booths algorithm to minimize generation of partial products
D. Sequential right shifts of the arguments
97. In general, when comparing BJT and MOSFET transistors, three main differences:
A. The device that depends more on geometry (width, Length, etc.) is BJT
B. The device is capable of higher amplification is MOSFET
C. The device that dissipates no power at the input (zero input current) is MOSFET
98. Which one of the engineering characteristics can best explain the following concept? Base your decision
on reason rather than emotion.
A. Quantitative Thinking
B. Interpersonal Skill
C. Honesty
D. Logical Thinking
99. Which of the following characteristics of a data network is never a correct of a packet switched
network?
A. A transmitted packet contains source and destination address coding, information, and error
control bits
B. Individual packets of a long message can be routed under different paths by the switching exchange
equipment
C. The address coding is transparent to a user.
D. A transmitted packet contains only information bits.
100. According to the Nyquist Sampling Theorem, a sufficient condition for these to be no aliasing in the
sampled signal is that the highest frequency in the signal point to sampling must be:
A. Less than the half of the sampling frequency.
B. Greater than half of the sampling frequency.
C. Less than the sampling frequency.
D. Greater than the sampling frequency.
101. If the signal is power doubled at a given transmitter, what is the decibel increase?
A. 0.5 dB
B. 2 dB
C. 3 dB
D. 4 dB
107. Two circuit components of reliability R1 = 0.92 ohms and R2 = 0.85 ohms. If anyone of the circuit
components fails circuit works perfect. What is the combination of reliability of both the components?
A. 0.78
B. 0.85
C. 0.92
D. 0.99
108. A variable resistance R is connected across a source of voltage V, if the value of the resistance R is
gradually varied, the relationship between I and R will be represented by which curve?
A. Figure A
B. Figure B
C. Figure C
D. Figure D
109. Considering the interdisciplinary nature of engineering projects currently, which of the below is true:
A. Engineers should be well trained in one specific field of engineering only
B. Engineers should be well trained in multiple engineering fields
C. Engineers should have a mild idea about all engineering fields
D. Engineers from a specific field should seek assistance from the specialized engineers in different
field
110. In 50hz induction machine, if the no load speed is 2900 RPM, the slip frequency is:
A. 0.33 Hz
B. 0.67 Hz
C. 1.33 Hz
D. 1.67 Hz
113. Which of the following regression models is not considered to be a linear regression model for
predicting Y in terms of X:
A.
B.
C.
D.
114. Which of the below device is faster and consumes less power in large scale projects?
A. DSP (Digital Signal Processing)
B. Microcontroller
C. FGPA (Field Programmable Gate Array)
D. ASIC (Application Specific Integrated Circuit)
A. A Tuned RF Amplifier
B. An FM amplifier
C. An IF Amplifier
D. An AF pre-amplifier
116. The highest element in the hierarchical breakdown of the WBS is:
A. Deliverables
B. A cost accounts
C. Work package
D. The project
117. The lowest element in the hierarchical breakdown of the WBS is:
A. Deliverables
B. A Work Package
C. A Cost Account
D. A Lowest Sub deliverable
E. An Object
F. None of the above
118. A Digital Signal Processor (DSP) is designed to perform FFT operations for a digital oscilloscope that
utilizes a 12-bit A/D converter, the most cost effective ALU architecture for this CPU is a:
A. Fixed point multiplier with an 8-bit data path
B. Floating point multiplier with an 8-bit data path
C. Fixed point multiplier with a 16-bit data path
D. Floating point multiplier with a 16-bit data path
120. Splitting project into tasks and estimate time and resources required to complete each task is called:
A. Project scheduling
B. Project optimization
C. Project Control
121. A large scale integrated (LSI) circuit is shown in the figure below. What is the best description of the
circuit?
A. Phase Detector
B. Phase Locked Loop
C. Clock Phase Skew Compensator
D. Multiphase Clock Extractor
123. The circuit shown is a ground fault protection scheme. The purpose of R is to:
A. ES = 12, LS = 15
B. ES = 13, LS = 22
C. ES = 19, LS = 24
D. ES = 22, LS = 24
125. In which of figure the relationship between voltage and current is in accordance with Ohms Law:
A. Figure A
B. Figure B
C. Figure C
D. Figure D
126. Which of the estimates listed would occur last in project time line?
A. Rough Order of Magnitude
B. Square Foot Estimate
C. Bid Estimate
D. Assemblies Estimate
127. The transfer function Y/R for the block diagram shown below is:
A.
B.
C.
D.
128. Figure 1 represents equivalent transformations of the components in Figure 2. The values of the
transformed source and resistor in Figure 1 are most nearly:
A.
B.
C.
D.