Download as xlsx, pdf, or txt
Download as xlsx, pdf, or txt
You are on page 1of 31

dk;Z dk uke%&35 oh okfguh ih0,0lh0 gsrq 200 O;fDr;ksa dh {kerk dh

cSjdDetails
dk fuekZ.k dk dk;ZA
of meassurement
Sanitary and water supply works
MEASUREMENT
SN ITEM OF WORK NO. L. B. D/H
Providing and fixing Indian type glazed earthen ware W.C. pan
of approved quality size 580mm Orisa pan (Jaquar
ESSCO,cera, hindware) with 100 mm Sand Cast Iron P or S
1 trap,P.V.C. Flush pipe including supply of all materials, labour
and T&P etc for the proper completion of the work including
removal of old pan etc. if so required.
1 84
Supply and fixing of P.V.C low level cistern 10 litre capacity
with all internal fittings (Perryware, cera,hindware,jaquar
ESSCO.) P.V.C. Connection 450 mm long, C.P. angle valve
2 15mm dia (L&k,Jaquar ESSCO or equiv.), brass ball cock
complete including suplly of all material, labour, T&P etc.
required for proper completion of the work.
1 84
Supply and fixing of White Glazed earthen ware wash hand
basin (Jaquar ESSCO, cera,hindware) with C.P. jali, angle
valve (L&k,Jaquar ESSCO or equiv.), PVC waste pipe,pillar
cock (L&k,Jaquar ESSCO or equiv.),bracket, pvc connection
3 pipe 15mm dia 450mm long etc complete including supply of
all materials,Labours,T&P etc.required for proper completion
of the work (22"X16"size)
1 44
Providing and fixing white vitreous china flat back or wall
corner type Flat back or angular front lipper urinal basin of
white glazed earthen ware 465x355x265 mm (Jaquar ESSCO,
cera,hindware) with CP angle valve, with fittings, standard size
C.P. brass flush pipe, spreaders with unions and clamps (all in
4 C.P. brass) with waste fitting as per IS : 2556, C.I. trap with
outlet grating and other couplings in C.P. brass, including
painting of fittings and cutting and making good the walls and
floors wherever required: Single half stall urinal with 5 litre
PVC. automatic flushing cistern
1 44
Supply and fixing of steel kitchen sink 610X510X200 mm
without drain board (eagle make),with C.P.jali, P.V.C. waste
5 pipe,bracket,including supply of all material, labour, T&P etc.
for proper completion of work.
1 3
Providing and fixing Looking mirror with polish of 600x450
mm size with bevelled edge complete including hard board
6 sheet with clips for mirror 600x450x5mm fixed with C.P. brass
screws and washers complete.
1 44
Providing and fixing of glass shelf 7/32'' thick 600x130 mm
size with C.P. Guard standard size and bracket including
7 supply of all material labour T&P required for proper
completion of the work
1 44
Providing and fixing soil, waste and vent pipes: 100 mm dia 1 1 1225
Sand cast iron S&S pipe neco Make including of all materials,
8 labour and T&P etc. required for proper completion of the
work.
Providing and fixing M.S. holder-bat clamps of approved 1 1 720
design to Sand Cast iron/cast iron (spun) pipe embedded in and
including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1
9 cement : 2 coarse sand : 4 graded stone aggregate 20 mm
nominal size), including cost of cutting holes and making good
the walls etc (100mm dia)

Providing and fixing HCI heel rest sanitary bend 100 mm dia 1 1 20
10 Sand cast iron S&S as per IS - 1729
Providing and fixing bend of required degree with access door, 1 1 240
insertion rubber washer 3 mm thick, bolts and nuts complete.
11 100 mm dia Sand cast iron S&S as per IS - 1729 (HEP Make)

Providing and fixing terminal guard. 100 mm. Sand cast iron 1 1 20
12 S&S as per IS - 1729. HEP MAKE
Providing and fixing collar 100 mm. Sand cast iron S&S as per 1 1 48
13 IS - 1729. HEP MAKE
Providing lead caulked joints to sand cast iron/centrifugally 1 1 1277
14 cast (spun) iron pipes and fittings of diameter. 100 mm.
Providing and fixing trap of self cleansing design with screwed 1 1 91
down or hinged grating with or without vent arm complete,
15 including cost of cutting and making good the walls and floors:
100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS:
3989

Painting or vanishing on iron work in small area or new wood


1225.00*0.11
work with one coat of redy mix priming paint & two coat of
16 approved superior quqlity redy mix paint of clear synthetic
varnish including supply of all materials, labour, T & P etc.
required for proper completion of work. (Si.No. 641,642)

Providing and fixing C.P. Soap dish, Jaquar ESSCO, 1 1 44


17 cera,hindware with concealed fitting including supply of all
material , labour T&P etc. complete.
Providing and fixing CP Brass towel rail 750x20mm together 1 1 44
18 with pair of CP brass brackets to fit the towel rail complete
Providing and fixing G.I. pipes complete with G.I. fittings and
19 clamps, i/c cutting and making good the walls etc. Internal
work - Exposed on wall,
a 20mmdia nominal bore 1 1 1260
b 25mm dia nominal bore 1 1 1344
c 32mmdia nominal bore 1 1 1008
d 40mmdia nominal bore 1 1 672
e 50mmdianominal bore 1 1 672
Providing and fixing G.I. Pipes complete with G.I. fittings and 1 1 1400
clamps, i/c making good the walls etc. concealed pipe,
20 including painting with anti corrosive bitumastic paint, cutting
chases and making good the wall : : 15 mm dia nominal bore
Providing and fixing G.I. Pipes complete with G.I. fittings and 1 1 1750
clamps, i/c making good the walls etc. concealed pipe,
21 including painting with anti corrosive bitumastic paint, cutting
chases and making good the wall : 20 mm dia nominal bore
Providing and fixing G.I. pipes complete with G.I. fittings
22 including trenching and refilling etc. External work
a 40mmdia nominal bore 1 1 200
b 50mm dia nominal bore 1 1 160
c 65mmdia nominal bore 1 1 160
d 80mmdia nominal bore 1 1 160
Providing and fixing gun metal gate valve with C.I. wheel of
23 approved quality (screwed end) :
a 25mm dia nominal bore 1 1 24
b 32mmdia nominal bore 1 1 24
c 40mmdia nominal bore 1 1 24
d 50mmdianominal bore 1 1 24
e 65mmdia nominal bore 1 1 24
f 80mmdia nominal bore 1 1 24
Providing and fixing C.P. brass shower heavy quality (Jaquar 1 1 44
ESSCO,cera,Hindware) with Over Head brass Shower Arm
24 240 mm long with wall flange (Jaquar ESSCO,cera, Hindware)
15mm inlet:100 mm diameter
Painting G.I. pipes and fittings with synthetic enamel white
25 paint with two coats over a ready mixed priming coat, both of
approved quality for new work :
a 20mmdia nominal bore 1 1 1260
b 25mm dia nominal bore 1 1 1344
c 32mmdia nominal bore 1 1 1008
d 40mmdia nominal bore 1 1 672
e 50mmdianominal bore 1 1 672
Painting G.I. pipes and fittings with two coats of anti-
26 corrosive bitumastic paint of approved quality :
a 40mmdia nominal bore 1 1 200
b 50mm dia nominal bore 1 1 160
c 65mmdia nominal bore 1 1 160
d 80mmdia nominal bore 1 1 160
Providing and filling sand of grading zone V or coarser grade,
27 allround the G.I. pipes in external work :
a 40mmdia nominal bore 1 1 200
b 50mm dia nominal bore 1 1 160
c 65mmdia nominal bore 1 1 160
d 80mmdia nominal bore 1 1 160
Providing and fixing G.I. Union in G.I. pipe including cutting
and threading the pipe and making long screws etc. complete
28 (New work) :

a 15mm dia nominal bore 1 1 14


b 20mmdia nominal bore 1 1 8
c 25mm dia nominal bore 1 1 8
d 32mmdia nominal bore 1 1 10
e 40mmdia nominal bore 1 1 10
f 50mmdianominal bore 1 1 10
Supply and Fixing C.P. brass bib cock heavy quality short 1 1 84
29 body of 15mm. dia.(L&K,Jaquar Essco)
Providing and fixing C.P. brass long body bib cock of 1 1 47
30 (L&K,jaquar essco) conforming to IS standards 15 mm
nominal bore
Providing and fixing C.P Angle valve 15mm dia (L&k,Jaquar 1 1 44
31 ESSCO or equiv.) for geyser points of approved quality 15
mm nominal bore.
Providing and fixing CP Jalli heavy quality. Circular type - 1 1 91
32 100 mm nominal dia
Excavating trenches of required width for pipes, cables, etc 1 1 190
including excavation for sockets, and dressing of sides,
ramming of bottoms, depth upto 1.5 m, including getting out
the excavated soil, and then returning the soil as required, in
layers not exceeding 20 cm in depth, including consolidating
33 each deposited layer by ramming, watering, etc. and disposing
of surplus excavated soil as directed, within a lead of 50 m :
All kinds of soil Pipes, cables etc, not exceeding 80 mm dia.
Providing and laying cement concrete 1:5:10 (1 cement : 5
coarse sand : 10 graded stone aggregate 40 mm nominal size)
34 all-round R.C.C pipes including bed concrete as per standard
design :
a 150 mm diameter R.C.C pipes 1 1 150

b 250 mm diameter R.C.C pipes 1 1 40

Providing and fixing square-mouth S.W. gully trap class SP-1 1 1 10


complete with C.I. grating brick masonry chamber with water
tight C.I. cover with frame of 300 x300 mm size (inside) the
weight of cover to be not less than 4.50 kg and frame to be not
35 less than 2.70 kg as per standard design: 100x100 mm size P
type With common burnt clay F.P.S. (non modular) bricks of
class designation 7.5

Providing and laying non-pressure NP2 class (light duty)


R.C.C. pipes with collars jointed with stiff mixture of cement
36 mortar in the proportion of 1:2 (1 cement : 2 fine sand)
including testing of joints etc. complete :
150 mm diameter R.C.C pipes 1 1 150
a
250 mm diameter R.C.C pipes 1 1 40
b
Constructing brick masonry manhole in cement mortar 1:4 ( 1 1 1 13
cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix
(1 cement : 1.5 coarse sand (zoneIII) : 3 graded stone aggregate
20 mm nominal size), foundation concrete 1:4:8 mix (1 cement
: 4 coarse sand : 8 graded stone aggregate 40 mm nominal
size), inside plastering 12 mm thick with cement mortar 1:3 (1
cement : 3 coarse sand) finished with floating coat of neat
cement and making channels in cement concrete 1:2:4 (1
cement : 2 coarse sand : 4 graded stone aggregate 20 mm
nominal size) finished with a floating coat of neat cement
37
complete as per standard design : Inside size 90x80 cm and 45
cm deep including C.I. cover with frame (light duty) 455x610
mm internal dimensions, total weight of cover and frame to be
not less than 38 kg (weight of cover 23 kg and weight of frame
15 kg) : With common burnt clay F.P.S. (non modular) bricks
of class designation 7.5
Inside size 120x90 cm and 90 cm deep including C.I. cover 1 1 3
with frame (medium duty) 500 mm internal diameter, total
weight of cover and frame to be not less than 116 kg (weight of
cover 58 kg and weight of frame 58 kg) : 19.7.2.1 With
38 common burnt clay F.P.S. (non modular) bricks of class
designation 7.5

Extra for depth for manholes : 19.8.1 Size 90x80 cm With 1 1 5.85
common burnt clay F.P.S. (non modular) bricks of class
39 designation 7.5

Size 120x90 cm 19.8.2.1 With common burnt clay F.P.S. (non 1 1 1.8
40 modular) bricks of class designation 7.5

Providing and fixing on wall face unplasticised Rigid PVC rain


water pipes conforming to IS : 13592 Type A, including
jointing with seal ring conforming to IS : 5382, leaving 10 mm
gap for thermal expansion, All fittings like two Nos Bend, one
no Coupler or any other accessories and P/F PVC pipe clips
41 fixed by means of 50x50x50mm hard wood plug, secrewed
with MS screws of required length in wall face including
cutting brick work and fixing in cement mortar 1:4(i) Single
socketed pipes. 110 mm diameter

RAIN WATER PIPE


FROM TERRACE TO G/L 1 1 8 40.50
FROM MUMMTY/WATER TANK TO TERRACE 1 1 1 4.80
TOTAL

Junior Engineer Assistant Engineer Executive Engineeer


Maint. Division No-1, (Civil) Maint. Division No-1, (Civil) Maint. Division No-1, (Civil)
P.W.D. Lucknow. P.W.D. Lucknow. P.W.D. Lucknow.
a dh {kerk dh

QTY. UNIT

84 Each

84 Each COL 0.60 0.35 3.15

44 Each ht 3.30 0.15 3.15

44 Each

3 Each

44 Each
44 Each
1225 Rmt

720 Each

20 Each

240 Each

20 Each

48 Each

1277 Each

91 Each

134.8 Sqm

44 Each

44 Each
1260 Rmt
1344 Rmt
1008 Rmt
672 Rmt
672 Rmt
1400 Rmt

1750 Rmt

200 Rmt
160 Rmt
160 Rmt
160 Rmt

24 Each
24 Each
24 Each
24 Each
24 Each
24 Each
44 Each

1260 Rmt
1344 Rmt
1008 Rmt
672 Rmt
672 Rmt
200 Rmt
160 Rmt
160 Rmt
160 Rmt

200 Rmt
160 Rmt
160 Rmt
160 Rmt

14 Each
8 Each
8 Each
10 Each
10 Each
10 Each
84 Each

47 Each

44 Each

91 Each

190 Rmt
150 Rmt

40 Rmt

10 Each

150 Rmt

40 Rmt

13 Each
3 Each

5.85 Rmt

1.8 Rmt

324.00
4.80
328.80 RM

, (Civil)
dk;Z dk uke%&35 oh okfguh ih0,0lh0 gsrq 200 O;fDr;ksa dh
{kerk dh cSjdBilldk fuekZ.k dk dk;ZA
of Quantity
Sanitary and water supply works
S No. Ref No Description of Item Qty Unit Rate Amount
D.S.R.- Providing and fixing Indian type glazed earthen
17.13.2 ware W.C. pan of approved quality size 580mm
Orisa pan (Jaquar ESSCO,cera, hindware) with
100 mm Sand Cast Iron P or S trap,P.V.C. Flush
1 pipe including supply of all materials, labour and
T&P etc for the proper completion of the work
including removal of old pan etc. if so required.

84 Each 2625.00 220500.00


D.S.R.- Supply and fixing of P.V.C low level cistern 10
17.18.1/18. litre capacity with all internal fittings (Perryware,
53.1/18.21. cera,hindware,jaquar ESSCO.) P.V.C.
1.1 Connection 450 mm long, C.P. angle valve
2 15mm dia (L&k,Jaquar ESSCO or equiv.), brass
ball cock complete including suplly of all
material, labour, T&P etc. required for proper
completion of the work.
84 Each 1862.00 156408.00
D.S.R.- Supply and fixing of White Glazed earthen ware
17.7.7,18.5 wash hand basin (Jaquar ESSCO, cera,hindware)
3.1/18.21.1 with C.P. jali, angle valve (L&k,Jaquar ESSCO
.1 or equiv.), PVC waste pipe,pillar cock
(L&k,Jaquar ESSCO or equiv.),bracket, pvc
3 connection pipe 15mm dia 450mm long etc
complete including supply of all
materials,Labours,T&P etc.required for proper
completion of the work (22"X16"size)
44 Each 3186.00 140184.00
D.S.R.- Providing and fixing white vitreous china flat
17.5.1 back or wall corner type Flat back or angular
front lipper urinal basin of white glazed earthen
ware 465x355x265 mm (Jaquar ESSCO,
cera,hindware) with CP angle valve, with fittings,
standard size C.P. brass flush pipe, spreaders
with unions and clamps (all in C.P. brass) with
4 waste fitting as per IS : 2556, C.I. trap with outlet
grating and other couplings in C.P. brass,
including painting of fittings and cutting and
making good the walls and floors wherever
required: Single half stall urinal with 5 litre PVC.
automatic flushing cistern

44 Each 5247.00 230868.00


D.S.R.- Supply and fixing of steel kitchen sink
17.10.2.1, 610X510X200 mm without drain board (eagle
make),with C.P.jali, P.V.C. waste
5 pipe,bracket,including supply of all material,
labour, T&P etc. for proper completion of work.

3 Each 2814.00 8442.00


D.S.R.- Providing and fixing Looking mirror with polish
17.31 of 600x450 mm size with bevelled edge complete
6 including hard board sheet with clips for mirror
600x450x5mm fixed with C.P. brass screws and
washers complete.
44 Each 1052.00
D.S.R.- Providing and fixing of glass shelf 7/32'' thick
17.33 600x130 mm size with C.P. Guard standard size
7 and bracket including supply of all material
labour T&P required for proper completion of the
work
44 Each 802.00
D.S.R.- Providing and fixing soil, waste and vent pipes:
17.35.1.1 100 mm dia Sand cast iron S&S pipe neco Make
8 including of all materials, labour and T&P etc.
required for proper completion of the work.
1225 Rmt 872.00 1068200.00
D.S.R.- Providing and fixing soil, waste and vent pipes:
17.35.2.1 75 mm dia Sand cast iron S&S pipe neco Make
9 including of all materials, labour and T&P etc.
required for proper completion of the work.
720 Rmt 0.00 0.00
D.S.R.- Providing and fixing M.S. holder-bat clamps of
12.38.1 approved design to Sand Cast iron/cast iron
(spun) pipe embedded in and including cement
concrete blocks 10x10x10 cm of 1:2:4 mix (1
9 cement : 2 coarse sand : 4 graded stone aggregate
20 mm nominal size), including cost of cutting
holes and making good the walls etc (100mm
dia)
720 Each 194.00 139680.00
D.S.R.- Providing and fixing HCI heel rest sanitary bend
10 17.40.1.2, 100 mm dia Sand cast iron S&S as per IS - 1729
20 Each 527.00 10540.00
D.S.R.- Providing and fixing bend of required degree
17.43.1.1, with access door, insertion rubber washer 3 mm
11 thick, bolts and nuts complete. 100 mm dia Sand
cast iron S&S as per IS - 1729 (HEP Make)
240 Each 551.00 132240.00
D.S.R.- Providing and fixing terminal guard. 100 mm.
12 17.56.1.1 Sand cast iron S&S as per IS - 1729. HEP
MAKE 20 Each 388.00 7760.00
D.S.R.- Providing and fixing collar 100 mm. Sand cast
13 17.57.1.1
iron S&S as per IS - 1729. HEP MAKE 48 Each 286.00 13728.00
D.S.R.- Providing lead caulked joints to sand cast
14 17.57.1.1 iron/centrifugally cast (spun) iron pipes and
fittings of diameter. 100 mm. 1277 Each 314.00 400978.00
D.S.R.- Providing and fixing trap of self cleansing design
17.60.1.1, with screwed down or hinged grating with or
without vent arm complete, including cost of
15 cutting and making good the walls and floors:
100 mm inlet and 100 mm outlet Sand cast iron
S&S as per IS: 3989
91 Each 995.00 90545.00
SOR-641- Painting or vanishing on iron work in small area
642 or new wood work with one coat of redy mix
priming paint & two coat of approved superior
quqlity redy mix paint of clear synthetic varnish
16 including supply of all materials, labour, T & P
etc. required for proper completion of work.
(Si.No. 641,642)
135 Sqm 109.50 14755.13
D.S.R.- Providing and fixing C.P. Soap dish, Jaquar
18.65 ESSCO, cera,hindware with concealed fitting
17 including supply of all material , labour T&P etc.
complete.
44 Each 494.00 21736.00
D.S.R.- Providing and fixing CP Brass towel rail
18 18.65 750x20mm together with pair of CP brass
brackets to fit the towel rail complete 44 Each 685.00 30140.00
D.S.R.- Providing and fixing G.I. pipes complete with
18.10- G.I. fittings and clamps, i/c cutting and making
19 good the walls etc. Internal work - Exposed on
wall,
a 1 20mmdia nominal bore 1260 Rmt 232.00 292320.00
b 2 25mm dia nominal bore 1344 Rmt 278.00 373632.00
c 3 32mmdia nominal bore 1008 Rmt 332.00 334656.00
d 4 40mmdia nominal bore 672 Rmt 405.00 272160.00
e 5 50mmdianominal bore 672 Rmt 484.00 325248.00
D.S.R.- Providing and fixing G.I. Pipes complete with
18.11.1 G.I. fittings and clamps, i/c making good the
walls etc. concealed pipe, including painting with
20 anti corrosive bitumastic paint, cutting chases and
making good the wall : : 15 mm dia nominal bore

1400 Rmt 289.00 404600.00


D.S.R.- Providing and fixing G.I. Pipes complete with
18.11.2 G.I. fittings and clamps, i/c making good the
walls etc. concealed pipe, including painting with
21 anti corrosive bitumastic paint, cutting chases and
making good the wall : 20 mm dia nominal bore

1750 Rmt 326.00 570500.00


D.S.R.- Providing and fixing G.I. pipes complete with
22 18.12 G.I. fittings including trenching and refilling etc.
External work
a 4 40mmdia nominal bore 200 Rmt 323.00 64600.00
b 5 50mm dia nominal bore 160 Rmt 370.00 59200.00
c 6 65mmdia nominal bore 160 Rmt 695.00 111200.00
d 7 80mmdia nominal bore 160 Rmt 841.00 134560.00
D.S.R.- Providing and fixing gun metal gate valve with
23 18.17 C.I. wheel of approved quality (screwed end) :
a 1 25mm dia nominal bore 24 Each 1082.00 25968.00
b 2 32mmdia nominal bore 24 Each 564.00 13536.00
c 3 40mmdia nominal bore 24 Each 658.00 15792.00
d 4 50mmdianominal bore 24 Each 844.00 20256.00
e 5 65mmdia nominal bore 24 Each 1445.00 34680.00
f 6 80mmdia nominal bore 24 Each 2153.00 51672.00
D.S.R.- Providing and fixing C.P. brass shower heavy
18.22.1 quality (Jaquar ESSCO,cera,Hindware) with
24 Over Head brass Shower Arm 240 mm long with
wall flange (Jaquar ESSCO,cera, Hindware)
15mm inlet:100 mm diameter
44 Each 805.00 35420.00
D.S.R.- Painting G.I. pipes and fittings with synthetic
18.38- enamel white paint with two coats over a ready
25 mixed priming coat, both of approved quality for
new work :
a 2 20mmdia nominal bore 1260 Rmt 17.60 22176.00
b 3 25mm dia nominal bore 1344 Rmt 23.00 30912.00
c 4 32mmdia nominal bore 1008 Rmt 27.50 27720.00
d 5 40mmdia nominal bore 672 Rmt 32.40 21772.80
e 6 50mmdianominal bore 672 Rmt 38.60 25939.20
D.S.R.- Painting G.I. pipes and fittings with two coats of
26 18.4.0 anti-corrosive bitumastic paint of approved
quality :
a 5 40mmdia nominal bore 200 Rmt 18.80 3760.00
b 6 50mm dia nominal bore 160 Rmt 22.60 3616.00
c 7 65mmdia nominal bore 160 Rmt 28.10 4496.00
d 8 80mmdia nominal bore 160 Rmt 32.60 5216.00
D.S.R.- Providing and filling sand of grading zone V or
27 18.41 coarser grade, allround the G.I. pipes in external
work :
a 5 40mmdia nominal bore 200 Rmt 149.70 29940.00
b 6 50mm dia nominal bore 160 Rmt 155.30 24848.00
c 7 65mmdia nominal bore 160 Rmt 245.10 39216.00
d 8 80mmdia nominal bore 160 Rmt 252.60 40416.00
D.S.R.- Providing and fixing G.I. Union in G.I. pipe
18.46 including cutting and threading the pipe and
28 making long screws etc. complete (New work) :

a 1 15mm dia nominal bore 14 Each 159.00 2226.00


b 2 20mmdia nominal bore 8 Each 189.00 1512.00
c 3 25mm dia nominal bore 8 Each 229.00 1832.00
d 4 32mmdia nominal bore 10 Each 301.00 3010.00
e 5 40mmdia nominal bore 10 Each 338.00 3380.00
f 6 50mmdianominal bore 10 Each 504.00 5040.00
D.S.R.- Supply and Fixing C.P. brass bib cock heavy
29 18.49.1 quality short body of 15mm. dia.(L&K,Jaquar
Essco) 84 Each 561.00 47124.00
D.S.R.- Providing and fixing C.P. brass long body bib
30 18.51.1 cock of (L&K,jaquar essco) conforming to IS
standards 15 mm nominal bore 47 Each 613.00 28811.00
D.S.R.- Providing and fixing C.P Angle valve 15mm dia
31 18.53.1 (L&k,Jaquar ESSCO or equiv.) for geyser points
of approved quality 15 mm nominal bore. 44 Each 548.00 24112.00
D.S.R.- Providing and fixing CP Jalli heavy quality.
32 18.58.1.1 Circular type - 100 mm nominal dia 91 Each 67.00 6097.00
D.S.R.- Excavating trenches of required width for pipes,
2.10.1.2 cables, etc including excavation for sockets, and
dressing of sides, ramming of bottoms, depth
upto 1.5 m, including getting out the excavated
soil, and then returning the soil as required, in
layers not exceeding 20 cm in depth, including
33 consolidating each deposited layer by ramming,
watering, etc. and disposing of surplus excavated
soil as directed, within a lead of 50 m : All kinds
of soil Pipes, cables etc, not exceeding 80 mm
dia.

190 Rmt 353.00 67070.00


D.S.R.- Providing and laying cement concrete 1:5:10 (1
19.2 cement : 5 coarse sand : 10 graded stone
34 aggregate 40 mm nominal size) all-round R.C.C
pipes including bed concrete as per standard
design :

a D.S.R.- 150 mm diameter R.C.C pipes


19.2.2 150 Rmt 970.00 145500.00
b D.S.R.- 250 mm diameter R.C.C pipes
19.2.4 40 Rmt 1308.00 52320.00
D.S.R.- Providing and fixing square-mouth S.W. gully
19.4.1.1 trap class SP-1 complete with C.I. grating brick
masonry chamber with water tight C.I. cover with
frame of 300 x300 mm size (inside) the weight of
cover to be not less than 4.50 kg and frame to be
35 not less than 2.70 kg as per standard design:
100x100 mm size P type With common burnt
clay F.P.S. (non modular) bricks of class
designation 7.5

10 Each 2240.00 22400.00


D.S.R.- Providing and laying non-pressure NP2 class
19.6 (light duty) R.C.C. pipes with collars jointed with
36 stiff mixture of cement mortar in the proportion
of 1:2 (1 cement : 2 fine sand) including testing
of joints etc. complete :

D.S.R.- 150 mm diameter R.C.C pipes


a 19.6.2 Rmt 449.00 67350.00
150
D.S.R.- 250 mm diameter R.C.C pipes
b 19.6.3 Rmt 732.00 29280.00
40
D.S.R.- Constructing brick masonry manhole in cement
19.7.1.1 mortar 1:4 ( 1 cement : 4 coarse sand ) with
R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5
coarse sand (zoneIII) : 3 graded stone aggregate
20 mm nominal size), foundation concrete 1:4:8
mix (1 cement : 4 coarse sand : 8 graded stone
aggregate 40 mm nominal size), inside plastering
12 mm thick with cement mortar 1:3 (1 cement :
3 coarse sand) finished with floating coat of neat
cement and making channels in cement concrete
1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) finished with a
floating coat of neat cement complete as per
37
standard design : Inside size 90x80 cm and 45 cm
deep including C.I. cover with frame (light duty)
455x610 mm internal dimensions, total weight of
cover and frame to be not less than 38 kg (weight
of cover 23 kg and weight of frame 15 kg) : With
common burnt clay F.P.S. (non modular) bricks
of class designation 7.5

13 Each 10590.00 137670.00


D.S.R.- Inside size 120x90 cm and 90 cm deep including
19.7.2.1 C.I. cover with frame (medium duty) 500 mm
internal diameter, total weight of cover and frame
to be not less than 116 kg (weight of cover 58 kg
38 and weight of frame 58 kg) : 19.7.2.1 With
common burnt clay F.P.S. (non modular) bricks
of class designation 7.5

3 Each 22277.00 66831.00


D.S.R.- Extra for depth for manholes : 19.8.1 Size 90x80
19.8.1.1 cm With common burnt clay F.P.S. (non
39 modular) bricks of class designation 7.5
6 Rmt 7286.00 42623.10
D.S.R.- Size 120x90 cm 19.8.2.1 With common burnt
19.8.2.1 clay F.P.S. (non modular) bricks of class
40 designation 7.5
2 Rmt 8734.00 15721.20
DSR- Providing and fixing on wall face unplasticised
12.41.2+12 Rigid PVC rain water pipes conforming to IS :
.42.1.2 13592 Type A, including jointing with seal ring
conforming to IS : 5382, leaving 10 mm gap for
thermal expansion, All fittings like two Nos
Bend, one no Coupler or any other accessories
and P/F PVC pipe clips fixed by means of
41
50x50x50mm hard wood plug, secrewed with
MS screws of required length in wall face
including cutting brick work and fixing in cement
mortar 1:4(i) Single socketed pipes. 110 mm
diameter

328.8 Rmt 493.00 162098.40


TOTAL 7038901.53
SAY IN RS 70.39

Junior Engineer Assistant Engineer Executive Engineeer


Maint. Division No-1, (Civil) Maint. Division No-1, (Civil) Maint. Division No-1, (Civil)
P.W.D. Lucknow. P.W.D. Lucknow. P.W.D. Lucknow.
Rate Analysis

Reference from CPWD Analysis of rate -2019, Item No.-17.60.2.2,


Providing and fixing trap of self cleansing design with screwed down or hinged grating with or
Item without vent arm complete, including cost of cutting and making good the walls and floors: 100 mm
No.- inlet and 75 mm outlet Sand Cast Iron S&S as per IS: 1729 ( 100x75 Nahani Trap 4.0 kg)

Sl.No. Description Unit Qty Rate Cost Rate Code Remark


Details of cost for 1 No
Material :-
100 mm S.C.I. trap with 100 mm inlet and SR
75 mm outlet No. 1.00 370.00 370.00
Cement, sand and grit etc L.S. 13.52 2.00 27.04 9999
Labour :-
Mason Ist class Day 1/2 450.00 225.00
SR
Beldar Day 1/2 310.00 155.00
Sub Total 777.04
Add water charges @ 1% 7.77
Total = 784.81
Add for contractor's proffit and
overheads @15% 117.72
Rate per No. 902.50
Say RS 902.00

Junior Engineer Assistant Engineer Ex. Engineer


Maint.Division 1,Civil Maint.Division 1,Civil Maint.Division 1,Civil
P.W.D. Lucknow P.W.D. Lucknow P.W.D. Lucknow
MEASUREMENT
SN ITEM OF WORK NO. L B
1 Providing and fixing soil, waste and vent pipes: 100 mm dia Sand cast iron S&S pipe
neco Make including of all materials, labour and T&P etc. required for proper
completion of the work.
A INSIDE
AT TYPICAL FLOOR- FOR SHEET-1 TO DUCT 1 1 3.60
FOR SHEET-2 TO DUCT 1 1 4.50
VERTICAL PIPE FOR TRAP 1 2 0.30
FOR ONE BATH Total
FOR ONE BATH-44 BATH
B IN DUCT- ONE NOS 1 1 42.00
FOR 4 NOS DUCT
Total

2 Providing and fixing soil, waste and vent pipes: 75 mm dia Sand cast iron S&S pipe
neco Make including of all materials, labour and T&P etc. required for proper
completion of the work.
A INSIDE
AT TYPICAL FLOOR- FOR W/B TO BATH TRAP 1 1 3.60
BATH TRAP TO DUCT 1 1 0.90
FOR ONE BATH Total
FOR ONE BATH-44 BATH
IN DUCT- ONE NOS 1 1 42.00
FOR 4 NOS DUCT
Total
3 Providing and fixing trap of self cleansing design with screwed down or hinged grating
with or without vent arm complete, including cost of cutting and making good the walls
and floors: 100 mm inlet and 75 mm outlet Sand Cast Iron S&S as per IS: 1729
( 100x75 Nahani Trap 4.0 kg) 44 2
4 Providing and fixing terminal guard. 100 mm. Sand cast iron S&S as per IS - 1729.
1 4
HEP MAKE
5 Providing and fixing terminal guard. 75 mm. Sand cast iron S&S as per IS - 1729.
HEP MAKE 1 4

6 Providing and fixing collar 100 mm. Sand cast iron S&S as per IS - 1729. HEP MAKE
44 2
4 10

7 Providing and fixing collar 75 mm. Sand cast iron S&S as per IS - 1729. HEP MAKE
44 2
4 10

8 Providing and fixing plain bend of required degree. 100 mm dia Sand cast iron S&S as
per IS -1729 HEP
44 2
9 Providing and fixing plain bend of required degree. 75 mm dia Sand cast iron S&S as
per IS -1729 HEP
44 2
10 Providing and fixing HCI croos with access door nuts and washer
complete100x100x100 mm dia Sand cast iron S&S as per IS -1729 HEP 4 12
11 Providing and fixing HCI croos with access door nuts and washer complete75x75x75
mm dia Sand cast iron S&S as per IS -1729 HEP 4 12
Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and
12 fittings of diameter. 100 mm.
1 1 558
Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and
13
fittings of diameter. 75 mm. 1 1 668
Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls
etc. Internal work - Exposed on wall,
14
OUT LET

32mmdia nominal bore 1 4 13.20


40mmdia nominal bore 1 4 13.20
50mmdianominal bore 1 4 16.20
IN LET-50MM 1 1 44.50

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc.
concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the
wall : : 15 mm dia nominal bore

AT TYPICAL FLOOR- VERTICAL 1 1 12.00


1 8 0.15
FOR ONE BATH Total
FOR ONE BATH-44 BATH
Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc.
concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the
wall : 20 mm dia nominal bore

AT TYPICAL FLOOR- HORIZONTAL 1 1 16.00


FOR ONE BATH Total
FOR ONE BATH-44 BATH
Junior Engineer Assistant Engineer
Maintenance Division No. 1(Civil) Maintenance Division No.1(Civil)
P.W.D. Lucknow. P.W.D. Lucknow.
ASUREMENT
D QTY. UNIT RATE AMOUNT

3.60
4.50
0.60
Total 8.70
382.80 a
42.00
168.00 b
(a+b) 550.80

3.60 3.60
0.90 0.90
Total 4.50 0.00 3.6
198.00 a 0.00
42.00 42.00
168.00 b 46.50
(a+b) 366.00 3 4

88 NO. 88
4 NO.
4
4 NO.
4

88
40
128 NO. 256

88 NO.
40
128 NO. 256

88 NO. 176

88 NO. 176
48 NO. 144

48 NO. 144 580

558 NO. 668

668 NO.

52.80
52.80 2
64.80 0.45
44.50 0.6
109.30 0.3

0.6
12.00 0.3
1.20 0.3
Total 13.20 2
580.80 a 6.55

16.00
Total 16.00
704.00 a
Ex. Engineeer
Maintenance Division No.1(Civil)
P.W.D. Lucknow.
Rate Analysis

Reference from CPWD Analysis of rate -2019, Item No.-17.39.1.1,


Item Providing and fixing plain bend of required degree. 100 mm dia Sand cast iron S&S as per IS -1729
No.- HEP

Sl.No. Description Unit Qty Rate Cost Rate Code Remark


Details of cost for 1 No
Material :-
S.C.I. plain bend 100 mm dia No. 1.00 380.00 380.00 UPPWD SR

Carriage of materials and fixing charges L.S. 13.52 2.00 27.04 9999
Sub Total 407.04
Add water charges @ 1% 4.07
Total = 411.11
Add for contractor's proffit and
overheads @15% 61.67
Rate per No. 472.80
472.00

Rate Analysis

Reference from CPWD Analysis of rate -2019, Item No.-17.39.2.1,


Item Providing and fixing plain bend of required degree. 75 mm dia Sand cast iron S&S as per IS -1729
No.- HEP

Sl.No. Description Unit Qty Rate Cost Rate Code Remark


Details of cost for 1 No
Material :-
S.C.I. plain bend 75 mm dia No. 1.00 318.00 318.00 UPPWD SR

Carriage of materials and fixing charges L.S. 10.79 2.00 21.58 9999
Sub Total 339.58
Add water charges @ 1% 3.40
Total = 342.98
Add for contractor's proffit and
overheads @15% 51.45
Rate per No. 394.40
394.00
Rate Analysis

Reference from CPWD Analysis of rate -2014, Item No.-17.39.2.1,


Item Providing and fixing plain bend of required degree. 75 mm dia Sand cast iron S&S as per IS -1729
No.- HEP/Equi.

Sl.No. Description Unit Qty Rate Cost Rate Code Remark


Details of cost for 1 No
Material :-
S.C.I. plain bend 75 mm dia No. 1.00 314.00 314.00 UPPWD SR

Carriage of materials and fixing charges L.S. 10.79 1.76 18.99 9999
Sub Total 332.99
Add water charges @ 1% 3.33
Total = 336.32
Add for contractor's proffit @15% 50.45
Rate per No. 386.80
Rate Analysis

Reference from CPWD Analysis of rate -2019, Item No.-17.39.1.1,


Item Providing and fixing HCI croos with access door nuts and washer complete100x100x100 mm dia
No.- Sand cast iron S&S as per IS -1729 HEP
Sl.No. Description Unit Qty Rate Cost Rate Code Remark
Details of cost for 1 No
Material :-
S.C.I. plain bend 100 mm dia No. 1.00 577.00 577.00 UPPWD SR
Carriage of materials and fixing charges L.S. 13.52 2.00 27.04 9999
Sub Total 604.04
Add water charges @ 1% 6.04
Add for contractor's proffit and Total = 610.08
overheads @15% 91.51
Rate per No. 701.60
701.00

Rate Analysis

Reference from CPWD Analysis of rate -2019, Item No.-17.39.2.1,


Item
Providing and fixing HCI croos with access door nuts and washer complete75x75x75 mm dia Sand
No.-
Sl.No. cast iron S&SDescription
as per IS -1729 HEP Unit Qty Rate Cost Rate Code Remark
Details of cost for 1 No
Material :-
S.C.I. plain bend 75 mm dia No. 1.00 490.00 490.00 UPPWD SR
Carriage of materials and fixing charges L.S. 10.79 2.00 21.58 9999
Sub Total 511.58
Add water charges @ 1% 5.12
Add for contractor's proffit and Total = 516.70
overheads @15% 77.50
Rate per No. 594.20
594.00
Rate Analysis

Reference from CPWD Analysis of rate -2014, Item No.-17.39.2.1,


Item
Providing and fixing plain bend of required degree. 75 mm dia Sand cast iron S&S as per IS -1729
No.-
Sl.No. HEP/Equi. Description Unit Qty Rate Cost Rate Code Remark
Details of cost for 1 No
Material :-
S.C.I. plain bend 75 mm dia No. 1.00 314.00 314.00 UPPWD SR
Carriage of materials and fixing charges L.S. 10.79 1.76 18.99 9999
Sub Total 332.99
Add water charges @ 1% 3.33
Total = 336.32
Add for contractor's proffit @15% 50.45
Rate per No. 386.80

You might also like