Professional Documents
Culture Documents
Code and Standard 소개 - 2018
Code and Standard 소개 - 2018
Code and Standard 소개 - 2018
박재홍 【 Contents 】
2018-12 1. Code 와 Standard의 차이
3. 배관관련 ASME 규격
4. 주요 규격
5. 각국 공업 규격
6. 국가 및 단체 표준
1. Code 와 Standard의 차이
Code(규격)와 Standard(표준)의 차이
1. 규격(Code) :
- 일반적으로 법, 법규, 규정 등으로 호칭, 강제요건(Mandatory)을 의미
- 일부 Standard가 Code에 인용되거나 Code에서 그 Standard를 준수하도록 요구한 경우는 Code
- ASME Code에서 특정 ASTM에 따를 것을 요구하였다면 그 ASTM은 Code가 됨
- Standard가 구매사양서(Procurement Specification)에서 명시되어 설비 및 기기 제작자가 이를 준수해야
하는 경우, 법적 효력을 갖게 되므로 해당 Standard는 Code로 간주
- 최종 사용자 또는 이해당사자의 생명과 재산을 보호하기 위한 규정을 제공
- 설계요건, 자재 및 제품상의 최소 요건, 검사 및 시험 요건, 동작절차 등을 규정
- 해당 법적 관할권을 가진 연방정부, 주정부 및 기타 지방자치단체에서 규정
- 정부(규제기관)에 의해 채택되었거나 계약에 의해 채택되었으며 법적 구속력을 갖고 있는 Standard
- 특수목적으로 특정분야에 관계되는 규정을 효과적으로 사용하기 위해 체계적으로 정리한 것
- OSHA, EPA, NFPA, ASME, CFR, NEC 등은 코드
1
1. Code 와 Standard의 차이
Code(규격)와 Standard(표준)의 차이
2. 표준(Standard) :
- 일반적으로 여러 산업체 또는 단체에서 발간된 임의요건(Not Mandatory, Recommendation)
- 극히 일부는 코드에 인용됨으로써 강제요건화 되어 코드라 불림
- 주로 민간단체나 전문가 조직(학회, 협회 및 기타 기구)의 자발적인 참여로 개발
- 구매시방, 계약요건, 또는 법에 참조되거나 인용되는 경우에만 당사자에게는 효력이 발생
- Standards는 자재 및 기기의 설계, 제작, 시험과 관련된 내용을 관련 산업계 또는 유관기관에서 발행
- 이해당사자 사이에 해당 자재 또는 기기에 대한 일관된 기준 또는 틀(framework)을 제공하는 역할
- 안전성과 상호 호환성을 확보하고 제품을 균일하게 만들기 위하여 개발된 일련의 기술적 정의와 가이드 라인
- 관계되는 조직간의 이익과 편의가 공정하게 얻어질 수 있도록 통일, 단순화를 목적 제품과 서비스에
직.간접으로 관계되는 사항에 대하여 정한 것
- IEEE, ANSI, ICEA, IEA, ASTM 등은 표준
◈ 표준의 분류
1) 성능표준(Performance Standards) : 기기의 정격과 성능에 관련하여 구매자와 공급자 상호간의 보호와 이해
상충의 최소화를 위한 계약 당사자 간의 합의에 필요한 성능, 기술기준, 시료의 개발 및 시험 등에 관한 기준을
제공
2) 재료 및 제품표준(Material and Product Standards) : 재료나 제품에 대한 특정 요건이나 설계, 제작/시공, 검사
및 시험에 대한 기준을 제공
3) 치수표준(Dimensional Standards) : 구성품에 대한 치수 및 허용공차를 제공
4) 시험표준(Testing Standards) : 계약 요건과 일치 여부를 입증하기 위한 시험의 형태 및 시험 절차를 제공
* IEEE(Institute of Electrical and Electronics Engineers, 전기 전자 기술자 협회),
* ANSI(American National Standard Institute, 미국 표준 협회),
* ICEA(Insulated Cable Engineers Association, 피복전선협회),
* IEA(International Energy Agency, 국제에너지기구),
* ASTM(American Society for Testing and Materials, 미국재료시험협회)
2
1. Code 와 Standard의 차이
Code(규격)와 Standard(표준)의 차이
From ASME B31.1
♣ Should
1) should : “should” or “it is recommended” is used to indicate that a provision is not mandatory but
recommended as good practice.
1) should : "should" 또는 "it is recommended 는 규정이 강제적이지는 않지만 모범관행으로서 추천되는 것을
가리킬 때 사용된다
♣ Shall
2) shall : “shall” or “shall not” is used to indicate that a provision or prohibition is mandatory.
2) shall : 코드의 영문에서 "shall" 또는 “shall not"은 규정이나 금지조항이 강제적임을 가리킬 때 사용된다
♣ May
3
1. Code 와 Standard의 차이
Code(규격)와 Standard(표준)의 차이
3. Code 및 Standard 작성 주체
Code & Standard를 만드는 주체는 대단히 많으나 개략적으로 4가지 주요 범주로 분류할 수 있다.
4. Specification(사양)
- 특정기기, 설비, 재료에 대해 요구되는 특정의 성능, 향상, 구조, 치수, 제조 및 시험방법 등을 규정한 것
- Code 및 Standard를 기초로 하여 사업주의 추가적인 요구사항을 반영할 수 있음.
4
1. Code 와 Standard의 차이
Code(규격)와 Standard(표준)의 차이
◈ 주요 Code and Standard
ANSI는 1918년에 미국에서 각종 단체들이 우후죽순 격으로 각종 Standard를 발행함에 따라 중복되는 경우가
발생하자 이를 방지하고자 Engineering Society와 Government Agency가 참여하여 결성한 미국산업표준을 관장
하는 비영리 기구이다. 과거에는 ANSI가 직접 Standard를 발행하는 경우도 있었지만 현재는 직접 Standard를 발
행하지 않고 다른 Standards Developing Organizations에서 만든 Standard의 발행 및 개정을 감독하고 있다. 따
라서 B31.1(Power Piping)의 경우 발행 연도에 따라 ANSI B31.1, ANSI/ASME B31.1, ASME B31.1와 같이 여러
가지로 표기되는 경우가 있는데 모두 동일하다. 가장 최신의 표기방법으로는 ASME B31.1이 맞는 표현이다.
미국의 국가 표준으로 ANSI에서 직접 개발, 발행된 것도 있지만 상당수는 다른 학회, 전문가 단체나 협회에서 개발
된것을 국가 표준으로 채택하였음. ANSI 번호와 개발한 단체(Sponsor)번호가 상이할 때는 둘다 표기("예" ANSI
XXXX/IEEE XXXX)
압력용기 제작, 설치, 시험과 관련한 표준을 제공하며, 순수 전기계통에는 EPA(Electrical Penetration Assembly,
격납건물 전기관통설비)를 제외하고는 적용되지 않음. ASME는 19세기경 산업혁명에 의한 급격한 산업발전에 따라
보일러의 사용압력이 빠른 속도로 증가하였고 이 결과 보일러 폭발사고도 급격히 증가하여 인명 손실이 증대됨에
따라 보일러 사고를 미연에 방지하고자 만들어졌다. 그 후 미국의 각 주가 이 규제를 법적으로 강제하게 된다.
Mechanical Engineering에 초점을 두고 있으나 여러 기술분야의 Code 및 Standard로서 주도적인 역할을 하고 있
고, 특히 원자력 설비 중 안전 관련 기기(Component)의 설계 및 제작에 적용되는 ASME BPVC Section Ⅲ를 발행
하고 있다.
5
1. Code 와 Standard의 차이
Code(규격)와 Standard(표준)의 차이
3) ASTM(American Society for Testing and Materials or ASTM International, 미국 재료 시험 학회)
기본적으로 자재 및 자재의 시험 방법, 절차 등을 다루고 있으며 다른 Codes & Standards에 인용되는 것이 일반적
미국의 초기 철도산업에서 선로용 강재(Steel)에 적용되는 규정을 만든 것에서 유래하였으며 재질,
제품, 검사(Test)방법 등에 대한 표준을 발행하고 있다.
KEPIC은 국내 전력산업 설비와 기기의 안전성과 신뢰성 및 품질확보를 위하여 설계, 제조, 시공, 운전시험 및 검사
등에 대한 방법과 절차를 규정한 상세 기술표준이다. 국내 전력설비의 건설과 운전에 적용한 외국의 관련 표준을
번안(adaptation)하여 제정하였고, 국내 현실에 맞게 일부 내용을 개정하였다. 현재 국내에서 원자력 안전성 품목
을 공급하고자 하는 업체는 KEPIC 자격인증서를 취득하여야 한다.
6
1. Code 와 Standard의 차이
Code(규격)와 Standard(표준)의 차이
7) NEMA(National Electrical Manufacturers Association, 전기 장비 제조업체 협회)
8) UL(Underwriters Laboratories)
Code(규격)와 Standard(표준)의 차이
11) NFPA(National Fire Protection Association, 미국 국제 화재 방재청)
NFPA는 화재 및 다른 위험의 가능성 및 효과를 최소화하기 위한 Code & Standard를 발행하는 기관이다.
HEI는 열교환기기 및 진공장치(Vacuum Apparatus)에 관련된 표준을 만드는 이 분야 최고의 기관이며 아래와 같
은 Standard를 발행하고 있다.
- Standards for Closed Feedwater Heaters
- Standards for Steam Surface Condensers
8
2. International Code and Standard
9
2. International Code and Standard
10
3. 배관관련 ASME 규격
배관 관련 ASME 규격
1. ASME B31.1 Power Piping 2. ASME B31.3 Process Piping
11
3. 배관관련 ASME 규격
배관 관련 ASME 규격
3. ASME B31.4 Pipeline Transportation 4. ASME B31.8 Gas transmission and
Systems for Liquids and Slurries Distribution Piping System
12
3. 배관관련 ASME 규격
배관 관련 ASME 규격
5. ASME B16 Series, B16 AMERICAN 5. ASME B16 Series List
NATIONAL STANDARDS FOR PIPING,
PIPE FLANGES, FITTINGS, AND VALVES
13
3. 배관관련 ASME 규격
14
4. 주요 규격
ASTM (미국 재료 시험 학회 )
Each ASTM standard has a unique serial designation. It is comprised 각 ASTM 표준에는 고유한 일련 번호가 있습니다. 일반 분류
of a capital letter indicating general classification (A, ferrous metals; (A, 철 금속, B, 비철 금속, C, 시멘트, 세라믹, 콘크리트 및 석
B, nonferrous metals; C, cementitious, ceramic, concrete, and 재, D, 기타 재료, E, 기타 과목, F, 특정 용도의 재료, G, 부식,
masonry materials; D, miscellaneous materials; E, miscellaneous 열화 및 재료 열화, ES, 긴급 표준, P, 제안, PS, 잠정 표준), 일
subjects; F, materials for specific applications; G, corrosion, 련 번호 (1 ~ 4 자리), 대시 및 발행 연도.
deterioration, and degradation of materials; ES, emergency
standards; P, proposals; PS, provisional standards), a serial number
(one to four digits), a dash, and the year of issue.
In each serial designation, the number following the dash indicates 각 연속 지정에서 대시 다음의 숫자는 원래 채택 연도를 표준
the year of original adoption as standard or, in the case of revision, 으로 표시하거나 개정의 경우 마지막 수정 연도를 나타냅니
the year of last revision. Thus, standards adopted or revised during 다. 따라서 2017 년에 채택되거나 개정 된 표준은 최종 번호
the year 2017 have as their final number, 17. A letter following this 가 17이다. 이 번호 뒤에 오는 문자는 그 해에 하나 이상의 개
number indicates more than one revision during that year, that is 정판을 나타내며, 17a는 2017 년에 두 번째 개정판을, 17b는
17a indicates the second revision in 2017, 17b the third revision, etc. 세 번째 개정판을 나타냅니다. 변경 없이 다시 승인 된 날짜
Standards that have been reapproved without change are indicated 는 지정 번호의 일부로 괄호 안에 마지막 재 승인 연도로 표
by the year of last reapproval in parentheses as part of the 시됩니다 (예 : (2017)). 위 첨자 엡실론은 마지막 개정 또는
designation number, for example, (2017). A superscript epsilon 재승 인 이후의 편집상의 변화를 나타냅니다. 첫 번째 변경의
indicates an editorial change since the last revision or reapproval; ε1 경우 ε1, 두 번째 변경의 경우 ε2 등.
for the first change, ε2 for the second, etc.
15
4. 주요 규격
ASTM (미국 재료 시험 학회 )
If a standard is written in acceptable metric units and has a 표준이 허용되는 미터법 단위로 작성되고 인치 - 파운드 단위
companion standard written in inch-pound units (or other units), (또는 기타 단위)로 작성된 보조 표준을 가지고있 는 경우, 일
the metric standard is identified by a letter M after the serial 련 번호 뒤에 미터법 표준이 M 자로 식별됩니다. 이 표준은 "
number; this standard contains “hard metric" units. 하드 메트릭“ 단위를 포함 합니다.
If a standard is written in inch-pound unit (or other units) and 표준이 인치 - 파운드 단위 (또는 기타 단위) 및 허용되는 미
acceptable metric units, the document is identified by a dual 터 단위로 작성된 경우 문서는 이중 영숫자로 식별됩니다.
alphanumeric designation.
When reference is made to a standard, the complete designation 표준을 참고할 때 완전한 지정이 주어져야 한다. 가장 좋은
should be given. Best practice is to state the designation and title. 방법은 지정 및 제목을 언급하는 것입니다
The boldface number(s) following the title refer to the volume(s) of 제목 뒤에 나오는 굵은 글씨는 표준이 나타나는 ASTM 표준
the Annual Book of ASTM Standards in which the standard appears. 연례 책의 권(양)을 나타냅니다.
16
4. 주요 규격
ASTM (미국 재료 시험 학회 )
17
4. 주요 규격
ASTM (미국 재료 시험 학회 )
18
4. 주요 규격
ASTM (미국 재료 시험 학회 )
19
4. 주요 규격
ASTM (미국 재료 시험 학회 )
20
4. 주요 규격
ASTM (미국 재료 시험 학회 )
21
4. 주요 규격
ASTM (미국 재료 시험 학회 )
22
4. 주요 규격
• Part A - Ferrous Material Specifications (철강 재료 사양) : 배관용 강관/ 열전도용 강관 / 관이음쇠 / 구조용 강 / 볼트용 강제 / 봉강 및 리베
트등
• Part B - Nonferrous Material Specifications (비철금속 재료 사양) : 알루미늄 및 알루미늄 합금 / 동 및 동합금 / 선재 / 동합금 주물 등
• Part C - Specifications for Welding Rods, Electrodes, and Filler Metals (용접봉, 전극 및 용기재) : 강 및 합금강/알루미늄 및 비알루미늄 합금
23
4. 주요 규격
• Subsection NCA - General Requirements for Division 1 and Division 2 (Division 1과 Division 2 일반 조건)
• Appendices (부록)
• Division I
* Subsection NB - Class 1 Components (제 1종 기기)
* Subsection NC - Class 2 Components (제 2종 기기)
* Subsection ND - Class 3 Components (제 3종 기기)
* Subsection NE - Class MC Components (MC종 기기)
* Subsection NF - Supports (기기의 지지 구조물)
* Subsection NG - Core Support Structures (코어의 지지 구조물)
* Subsection NH - Class 1 Components in Elevated Temperature Service (고온 서비스의 제 1종 기기)
• Division 2 - Code for Concrete Containments (콘크리트 격납용기 규정)
• Division 3 - Containments for Transportation and Storage of Spent Nuclear Fuel and High Level Radioactive
Material and Waste (사용 후 핵연료 및 고준위 방사성 폐기물의 운송 및 저장 용 용기)
VI Recommended Rules for the Care and Operation of Heating Boilers (난방 보일러의 관리 및 운영에 대한 권장 규칙)
일상 조작연료 / 보일러용 기기의 조작과 보수 / 검사 / 내부의 화학적 조건 제어 등
VII Recommended Guidelines for the Care of Power Boilers (동력 보일러 관리를위한 권장 가이드 라인)
24
4. 주요 규격
XI Rules for Inservice Inspection of Nuclear Power Plant Components (원자력 발전 요소의 가동 중 검사 규정)
일반 요구 사항 / 원자력 발전소 펌프의 운전 중 테스트 / 원자력 발전소 밸브의 운전 중 테스트 등
XI Rules for Construction and Continued Service of Transport Tanks (운송 탱크의 건설 및 지속 서비스 규칙)
25
4. 주요 규격
26
4. 주요 규격
27
4. 주요 규격
■ 부문별 규격
∙ Marketing (마케팅)
∙ Pipeline Transportation (송유관 운송)
∙ Refining (정제)
∙ Valves (밸브)
∙ Industry Training (산업 교육)
∙ Health Environment and Safety (보건, 환경 및 안전)
28
4. 주요 규격
분 야 비고
Mechanical Equipment Standards for Refinery Service ( API 610, 611, 612, 613, 614, 616, 617, 618, 619, Refinery 서비스를 위한 기계 설
670, 671, 672, 674, 675, 676, 677, 681, 682, 684, 686), 비 표준
Storage Tanks (API 575, 620, 650, 651, 652, 653, 937, 1604, 1615, 1631, 2000, 2510, 2610) 저장 탱크
정제 서비스를 위한 압력 제거 시
Pressure – Relieving Systems for Refinery Service (API 520 Ptl & 2, 521, 526, 527, 574, 2000)
스템
Piping Component Standards (API 570, 574, 578, 591, 594, 598, 599, 600, 602, 603, 607, 608, 609) 배관 구성품 (부품) 표준
Electrical Installations and Equipment (API 500, 505, 540, 541, 546) 전기 설치 및 장비
Refinery 서비스를 위한 열 전달
Heat Transfer Equipment Standards for Refinery Service (API 530, 534, 535, 536, 560, 570, 660, 661, 662)
장비 표준
29
4. 주요 규격
PUBL 937 Evaluation of Design Criteria for Storage Tanks with Frangible Roof Joints 1996.04.01
Recommended Practice for Classification of Locations for Electrical Installations at Petroleum Facillities Classifie
RP 500 2012.12.01
d as Class I , Division 1 and Division 2
Recommended Practice for Classification of Locations for Electrical Installations at Petroleum Facillities Classifie
RP 505 1997.11.01 (R 2013)
d as Class I , Zone 0, Zone 1, and Zone 2
RP 534 Heat Recovery Steam Generators 2007.02.01 (R 2013)
RP 535 Burners for Fired Heaters in General Refinery Services 2014.05.01
RP 536 Post-Combustion Nox Control for Fired Equipment in General Refinery Services 2006.12.01 (R 2013)
RP 540 Electrical Installations in Petroleum Processing Plants 1999.04.01 (R 2004)
RP 551 Process Measurement Instrumentation 2016.02.01
RP 552 Transmission Systems 1994.10.01 (R 2007)
RP 553 Refinery Control Valves 2012.10.01
RP 554 Process Instrumentation and Control PART 1 2007.07.01 (R 2016)
RP 554 Process Instrumentation and Control PART 2 2008.10.01 (R 2016)
RP 554 Process Instrumentation and Control PART 3 2008.10.01 (R 2016)
RP 555 Process Analyzers 2013.06.01
RP 556 Fired Heaters & Steam Generators 2011.04.01
RP 572 Inspection of Pressure Vessels 2016.12.01
RP 573 Inspection of Fired Boilers and Heaters 2013.10.01
RP 574 Inspection Practices for Piping System Components 2016.11.01
RP 575 Inspection Practices for Atmospheric and Low-Pressure Storage Tanks 2014.04.01
RP 576 Inspection of Pressure Relieving Devices 2009.11.01
30
4. 주요 규격
STD 520 Sizing, Selection, and Installation of Pressure-relieving Devices Part I 2014.07.01
STD 520 Sizing, Selection, and Installation of Pressure-relieving Devices Part II 2015.03.01
STD 521 Pressure-relieving and Depressureing Systems 2014.01.01
STD 526 Flanged Steel Pressure-relief Valves 2009.04.01
STD 527 Seat Tightness of Pressure Relief Valves 2014.11.01
STD 530 Calculation of Heater-tube Thickness in Petroleum Refineries 2015.04.01
STD 541 Form-wound Squirrel Cage Induction Motors-375 kW (500 Horsepower) and Larger 2014.12.01
STD 546 Brushless Synchronous Machines - 500kVA and Larger 2008.09.01
STD 560 Fired Heaters for General Refinery Service - FIFTH EDITION 2016.02.01
31
4. 주요 규격
32
4. 주요 규격
33
4. 주요 규격
■ Publications by Number
2017.Mar.06
NO 코드명 Title Remark
Latest Edition
Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fitti
1 MSS SP-6 2012.01.01
ngs
2 MSS SP-9 Spot Facing for Bronze, Iron, and Steel Flanges 2013.01.01
3 MSS SP-25 Standard Marking System for Valves, Fittings, Flanges, and Unions 2013.01.01
Corrosion-Resistant Gate, Globe, Angle, and Check Valves with Flanged and Butt Weld Ends (Classes
4 MSS SP-42 2013.01.01
150, 300, & 600)
5 MSS SP-43 Wrought and Fabricated Butt-Welding Fittings for Low Pressure, Corrosion Resistant Applications 2013.01.01
6 MSS SP-44 Steel Pipeline Flanges 2016.01.01
7 MSS SP-45 Bypass and Drain Connections 2003.01.01 (R 2008)
8 MSS SP-51 Class 150LW Corrosion Resistant Flanges and Cast Flanged Fittings 2012.01.01
Quality Standard for Steel Castings and Forgings for Valves, Flanges, Fittings, and Other Piping Com
9 MSS SP-53 2012.01.01
ponents - Magnetic Particle Examination Method
Quality Standard for Steel Castings for Valves, Flanges, Fittings, and Other Piping Components - Ra
10 MSS SP-54 2013.01.01
diographic Examination Method
34
4. 주요 규격
35
4. 주요 규격
36
4. 주요 규격
37
4. 주요 규격
38
4. 주요 규격
39
4. 주요 규격
■낱규격
부 문 종수
MR(Materials Requirements) 4종
RP(Recommended Practices) 17 종
SP(Standards Practice) 75 종
TM(Test Methods) 43 종
40
4. 주요 규격
1 NACE ASTM G193-12D Standard Terminology and Acronyms Relating to Corrosion 2012
2 NACE No. 1/SSPC-SP 5, White Metal Blast Cleaning 2006
3 NACE No. 2/SSPC-SP 10, Near-White Metal Blast Cleaning 2006
4 NACE No. 3/SSPC-SP 6, Commercial Blast Cleaning 2006
5 NACE No. 4/SSPC-SP 7, Brush-Off Blast Cleaning 2006
6 NACE No. 6/SSPC-SP 13, Surface Preparation of Concrete 2003
7 NACE No. 8/SSPC-SP 14, Industrial Blast Cleaning 2006
NACE No. 10/SSPC-PA 6, Fiberglass-Reinforced Plastic (FRP) Linings Applied to Bottoms of Carbon Steel Aboveground Storage
8 2002
Tanks
9 NACE No. 11/SSPC-PA 8, Thin-Film Organic Linings Applied in New Carbon Steel Process Vessels 2003
NACE No. 12/AWS C2.23M/SSPC-CS 23.00, Specification for the Application of Thermal Spray Coatings (Metallizing) of Aluminu
10 2016
m, Zinc, and Their Alloys and Composites for the Corrosion Protection of Steel
11 ANSI/NACE No. 13/SSPC-ACS-1 Industrial Coating and Lining Application Specialist Qualification and Certification 2015
MR (MATERIAL REQUIREMENTS)
1 MR0103-2012, Materials Resistant to Sulfide Stress Cracking in Corrosive Petroleum Refining Environments 2015
2 MR0174-2007, Selecting Inhibitors for Use as Sucker-Rod Thread Lubricants 2007
NACE MR0175/ISO 15156, Petroleum and natural gas industries—Materials for use in H2S-containing environments in oil and
3 2015
gas production
4 MR0176-2012, Metallic Materials for Sucker-Rod Pumps for Corrosive Oilfield Environments 2012
41
4. 주요 규격
RP (RECOMMENDED PREACTICE)
1 ANSI/NACE Standard SP0104-2014, The Use of Coupons for Cathodic Protection Monitoring Applications 2014
2 RP0105-2005, Liquid-Epoxy Coatings for External Repair, Rehabilitation, and Weld Joints on Buried Steel Pipelines 2005
3 RP0281-2004, Method for Conducting Coating (Paint) Panel Evaluation Testing in Atmospheric Exposures 2004
4 SP0287-2016, Field Measurement of Surface Profile of Abrasive Blast-Cleaned Steel Surfaces Using a Replica Tape 2016
5 RP0291-2005, Care, Handling, and Installation of Internally Plastic-Coated Oilfield Tubular Goods and Accessories 2005
ANSI/NACE SP0300-2016/ISO 16784-1:2016, Corrosion of metals and alloys—Corrosion and fouling in industrial co
6 2016
oling water systems—Part 1
7 RP0303-2003, Field-Applied Heat-Shrinkable Sleeves for Pipelines: Application, Performance, and Quality Control 2003
8 SP0304-2016 (Formerly RP0304), Design, Installation, and Operation of Thermoplastic Liners for Oilfield Pipelines 2016
RP0375-2006, Field-Applied Underground Wax Coating Systems for Underground Pipelines: Application, Performanc
9 2006
e, and Quality Control
SP0391-2016 (Formerly RP0391), Materials for the Handling and Storage of Commercial Concentrated (90 to 100%)
10 2016
Sulfuric Acid at Ambient Temperatures
SP0394-2013 (formerly RP0394), Application, Performance, and Quality Control of Plant-Applied, Fusion-Bonded Ep
11 2013
oxy External Pipe Coating
RP0399-2004, Plant-Applied, External Coal Tar Enamel Pipe Coating Systems: Application, Performance, and Quality
12 2004
Control
RP0402-2002, Field-Applied Fusion-Bonded Epoxy (FBE) Pipe Coating Systems for Girth Weld Joints: Application, Pe
13 2002
rformance, and Quality Control
RP0495-2003, Guidelines for Qualifying Personnel as Abrasive Blasters and Coating and Lining Applicators in the Ra
14 2003
il Industries
15 RP0497-2004, Field Corrosion Evaluation Using Metallic Test Specimens 2004
16 RP0602-2002, Field-Applied Coal Tar Enamel Pipe Coating Systems: Application, Performance, and Quality Control 2002
17 RP0692-2003, Application of a Coating System to Exterior Surfaces of Steel Rail Cars 2003
42
4. 주요 규격
SP (STANDARD PRACTICE)
SP0100-2014 (formerly RP0100), Cathodic Protection to Control External Corrosion of Concrete Pressure Pipelines a
1 2014
nd Mortar-Coated Steel Pipelines for Water or Waste Water Service
2 SP0102-2010 (formerly RP0102), In-Line Inspection of Pipelines 2010
3 SP0106-2006, Control of Internal Corrosion in Steel Pipelines and Piping Systems 2006
4 SP0107-2007, Electrochemical Realkalization and Chloride Extraction for Reinforced Concrete 2007
5 SP0108-2008, Corrosion Control of Offshore Structures by Protective Coatings 2008
SP0109-2009, Field Application of Bonded Tape Coatings for External Repair, Rehabilitation, and Weld Joints on Bur
6 2009
ied Metal Pipelines
7 SP0110-2010 Wet Gas Internal Corrosion Direct Assessment Methodology for Pipelines 2010
8 SP0111-2011, Coating Technical File in Accordance with the IMO Performance Standard for Protective Coatings 2011
9 SP0112-2012 Corrosion Management of Atmospherically Exposed Reinforced Concrete Structures 2012
10 SP0113-2013 Pipeline Integrity Method Selection 2013
SP0169-2013 (formerly RP0169), Control of External Corrosion on Underground or Submerged Metallic Piping Syste
11 2013
ms
SP0170-2012 Protection of Austenitic Stainless Steels and Other Austenitic Alloys from Polythionic Acid Stress Corro
12 2012
sion Cracking During a Shutdown of Refinery Equipment
SP0176-2007 (formerly RP0176), Corrosion Control of Submerged Areas of Permanently Installed Steel Offshore Str
13 2007
uctures Associated with Petroleum Production
SP0177-2014 (formerly RP0177), Mitigation of Alternating Current and Lightning Effects on Metallic Structures and
14 2014
Corrosion Control Systems
SP0178-2012 (formerly RP0178), Design, Fabrication, and Surface Finish Practices for Tanks and Vessels to Be Lined
15 2012
for Immersion Service
16 SP0181-2006 (formerly RP0181), Liquid-Applied Internal Protective Coatings for Oilfield Production Equipment 2006
SP0185-2007 (formerly RP0185), Extruded Polyolefin Resin Coating Systems with Soft Adhesives for Underground or
17 2007
Submerged Pipe
18 SP0186-2007 (formerly RP0186), Application of Cathodic Protection for External Surfaces of Steel Well Casings 2007
19 SP0187-2008 (formerly RP0187), Design Considerations for Corrosion Control of Reinforcing Steel in Concrete. 2008
43
4. 주요 규격
SP (STANDARD PRACTICE)
SP0188-2006 (formerly RP0188), Discontinuity (Holiday) Testing of New Protective Coatings on Conductive Substrat
20 2006
es
21 SP0189-2013 (formerly RP0189), "Online Monitoring of Cooling Water Systems" 2013
22 SP0191-2008 (formerly RP0191), Application of Internal Plastic Coatings for Oilfield Tubular Goods and Accessories 2008
23 SP0192-2012 Monitoring Corrosion in Oil and Gas Production with Iron Counts 2012
24 SP0195-2007 (formerly RP0195), Corrosion Control of Sucker Rods by Chemical Treatment 2007
SP0196-2015 (formerly RP0196), “Galvanic Anode Cathodic Protection of Internal Submerged Surfaces of Steel Wate
25 2015
r Storage Tanks”
26 SP0198-2016, Control of Corrosion Under Thermal Insulation and Fireproofing Materials—A Systems Approach 2016
NACE SP0199-2009 (Formerly RP0199), Installation of Stainless Chromium-Nickel Steel and Nickel-Alloy Roll-Bonde
27 2009
d and Explosion-Bonded Clad Plate in Air Pollution Control Equipment
28 SP0200-2014 (formerly RP0200), Steel-Cased Pipeline Practices 2014
29 SP0204-2015 (formerly RP0204), Stress Corrosion Cracking (SCC) Direct Assessment Methodology 2015
SP0205-2010 Design, Fabrication, and Inspection of Tanks for the Storage of Petroleum Refining Alkylation Unit Sp
30 2010
ent Sulfuric Acid at Ambient Temperatures
SP0206-2016, Internal Corrosion Direct Assessment Methodology for Pipelines Carrying Normally Dry Natural Gas (
31 2016
DG-ICDA)
SP0207-2007, Performing Close-Interval Potential Surveys and DC Surface Potential Gradient Surveys on Buried or S
32 2007
ubmerged Metallic Pipelines
33 SP0208- Internal Corrosion Direct Assessment Methodology for Liquid Petroleum Pipelines 2008
34 SP0210-2010, Pipeline External Corrosion Confirmatory Direct Assessment 2010
35 SP0213-2013, Definition of Set Soluble Salt Levels by Conductivity Measurements 2013
36 SP0214-2014 Inspection, Cleaning, and Remediation Technology for Water Piping in Buildings 2014
37 SP0273-2016 (formerly RP0273), Handling and Proper Usage of Inhibited Oilfield Acids 2016
38 SP0274-2011, High-Voltage Electrical Inspection of Pipeline Coatings 2011
39 SP0285-2011 (formerly RP0285), “Corrosion Control of Underground Storage Tank Systems by Cathodic Protection” 2011
40 SP0286-2007 (formerly RP0286), Electrical Isolation of Cathodically Protected Pipelines 2007
44
4. 주요 규격
SP (STANDARD PRACTICE)
41 SP0288-2011, Inspection of Lining Application in Steel and Concrete Equipment 2011
SP0290-2007 (formerly RP0290), Impressed Current Cathodic Protection of Reinforcing Steel in Atmospherically Exp
42 2007
osed Concrete Structures
43 SP0292-2012 Installation of Thin Metallic Wallpaper Lining in Air Pollution Control and Other Process Equipment 2012
SP0294-2006 (formerly RP0294), Design, Fabrication, and Inspection of Tanks for the Storage of Concentrated Sulfur
44 2006
ic Acid and Oleum at Ambient Temperatures
SP0295-2008 (formerly RP0295), Application of a Coating System to Interior Surfaces of New and Used Rail Tank Ca
45 2008
rs
SP0296-2016 (formerly RP0296-2004), Detection, Repair, and Mitigation of Cracking in Refinery Equipment in Wet H
46 2016
2S Environments
SP0297-2012 Maintenance Painting of Electrical Substation Apparatus Including Flow Coating of Transformer Radiat
47 2012
ors
48 SP0298-2007 (formerly RP0298), Sheet Rubber Linings for Abrasion and Corrosion Service 2007
SP0302-2007 (formerly RP0302), Selection and Application of a Coating System to Interior Surfaces of New and Use
49 2007
d Rail Tank Cars in Molten Sulfur Service
50 SP0308-2008, Inspection Methods for Corrosion Evaluation of Conventionally Reinforced Concrete Structures 2008
51 SP0313-2013 Guided Wave Technology for Piping Applications 2013
SP0386-2007 (formerly RP0386), Application of a Coating System to Interior Surfaces of Covered Steel Hopper Railc
52 2007
ars in Plastic, Food, and Chemical Service
SP0387-2014 (formerly RP0387), Metallurgical and Inspection Requirements for Cast Galvanic Anodes for Offshore
53 2014
Applications
54 SP0388-2014 (formerly RP0388), Impressed Current Cathodic Protection of Internal Submerged Surfaces 2014
SP0390-2009 (formerly RP0390), Maintenance and Rehabilitation Considerations for Corrosion Control of Atmosphe
55 2009
rically Exposed Existing Steel-Reinforced Concrete Structures
56 SP0395-2013 (formerly RP0395) Fusion-Bonded Epoxy Coating of Steel Reinforcing Bars 2013
SP0398-2014 (formerly RP0398), Recommendations for Training and Qualifying Personnel as Railcar Coating and Lin
57 2014
ing Inspectors
45
4. 주요 규격
SP (STANDARD PRACTICE)
SP0403-2015 (formerly RP0403), Avoiding Caustic Stress Corrosion Cracking of Carbon Steel Refinery Equipment an
58 2015
d Piping
59 SP0407-2013, Format, Content, and Guidelines for Developing a Materials Selection Diagram 2013
60 SP0408-2014 Cathodic Protection of Reinforcing Steel in Buried or Submerged Concrete Structures 2014
SP0472-2015 (formerly RP0472), Methods and Controls to Prevent In-Service Environmental Cracking of Carbon Ste
61 2015
el Weldments in Corrosive Petroleum Refining Environments
SP0487-2007 (formerly RP0487), Considerations in the Selection and Evaluation of Rust Preventives and Vapor Corr
62 2007
osion Inhibitors for Interim (Temporary) Corrosion Protection
SP0490-2007 (formerly RP0490), Holiday Detection of Fusion-Bonded Epoxy External Pipeline Coating of 250 to 760
63 2007
μm (10 to 30 mil)
64 SP0491-2012 Worksheet for the Selection of Oilfield Nonmetallic Seal Systems 2012
65 SP0492-2016 (formerly RP0492), Metallurgical and Inspection Requirements for Offshore Pipeline Bracelet Anodes 2016
66 SP0499-2012 (formerly TM0299-99), Corrosion Control and Monitoring in Seawater Injection Systems 2012
67 ANSI/NACE SP0502-2010, Pipeline External Corrosion Direct Assessment Methodology 2010
68 SP0507-2014 External Corrosion Direct Assessment (ECDA) Integrity Data Exchange (IDX) Format 2014
69 SP0508-2010, Methods of Validating Equivalence to ISO 8502-9 on Measurement of the Levels of Soluble Salts 2010
SP0572-2007 (formerly RP0572), Design, Installation, Operation, and Maintenance of Impressed Current Deep Anod
70 2007
e Beds
71 SP0575-2007 (formerly RP0575), Internal Cathodic Protection (CP) Systems in Oil-Treating Vessels 2007
72 SP0590-2015 (formerly RP0590), Prevention, Detection, and Correction of Deaerator Cracking 2015
SP0592-2006 (formerly RP0592), Application of a Coating System to Interior Surfaces of New and Used Rail Tank Ca
73 2006
rs in Concentrated (90 to 98%) Sulfuric Acid Service
SP0775-2013 (formerly RP0775) Preparation, Installation, Analysis, and Interpretation of Corrosion Coupons in Oilfiel
74 2013
d Operations
SP0892-2007 (formerly RP0892), Coatings and Linings over Concrete for Chemical Immersion and Containment Serv
75 2007
ice
46
4. 주요 규격
미국 철강 도금 ∙ 도장 위원회
도장 및 도금에 의한 강재의 보호, 강구조의 선정과 도장에 관한 가이드 (2권의 Manual 로 간행)
47
4. 주요 규격
번호 구격 번호 제목 날짜
Guide for the Identification and Use of Industrial Coating Material in Computerized Product D
1 SSPC GUIDE 13 1998.12.01
atabases
2 SSPC A BOOK Good Painting Practice Steel Structures Painting Manual Volume 1 1993.09.01
2015.01.12
3 SSPC AB 1 Mineral and Slag Abrasives
(E 2017)
2015.03.02
4 SSPC AB 2 Cleanliness of Recycled Ferrous Metallic Abrasives
(E 2016)
2003.02.01
5 SSPC AB 3 Ferrous Metallic Abrasive
(E 2004)
6 SSPC AB 4 Recyclable Encapsulated Abrasive Media (in a compressible cellular matrix) 2009.09.01
7 SSPC ACS 1 Industrial Coating and Lining Application Specialist Qualification and Certification 2008.01.01
SSPC AMBIENT CONDITI
8 MONITORING AND CONTROLLING CONTROLLING DURING COATING OPERATIONS 2004.11.01
ONS
9 SSPC CHAPTER 1 HOW TO USE SSPC STANDARDS, SPECIFICATIONS, AND GUIDES 2004.11.01
Specification for the Application of Thermal Spray Coatings (Metallizing) of Aluminum, Zinc, a
10 SSPC CS 23.00 nd Their Alloys and Composites for the Corrosion Protection of Steel - NACE No.12; AWS C2. 2003.07.01
23M/C2.23
GUIDE FOR CONTAINING SURFACE PREPARATION DEBRIS GENERATED DURING PAINT REMO
11 SSPC GUIDE 6 2015.05.04
VAL OPERATIONS
12 SSPC GUIDE 7 GUIDE TO THE DISPOSAL OF LEADCONTAMINATED SURFACE PREPARATION DEBRIS 2015.07.09
1994.07.01
13 SSPC GUIDE 9 Guide for Atmospheric Testing of Coatings in the Field
(E 2004)
48
4. 주요 규격
번호 구격 번호 제목 날짜
Guide to Specifying Coatings Conforming to Volatile Organic Compound (VOC) Content Requi 1994.08.01
14 SSPC GUIDE 10
rements (E 2001)
1998.06.01
15 SSPC GUIDE 12 Guide for Illumination of Industrial Painting Projects
(E 2004)
Guide for the Identification and Use of Industrial Coating Materials in Computerized Product 1998.12.01
16 SSPC GUIDE 13
Databases (E 2004)
Guide for the Repair of Imperfections in Galvanized, Organic, or Inorganic Zinc-Coated Steel 1999.05.01
17 SSPC GUIDE 14
Using Organic Zinc-Rich Coatings (E 2004)
Field Methods for Extraction and Analysis of Soluble Salts on Steel and Other Nonporous Sub
18 SSPC GUIDE 15 2013.08.21
strates
19 SSPC GUIDE 16 Guide to Specifying and Selecting Dust Collectors 2003.08.01
Guide to Developing a Corporate Safety Program for Industrial Painting and Coating Contract
20 SSPC GUIDE 17 2004.01.01
ors
Specifier's Guide for Determining Containment Class and Environmental Monitoring Strategie
21 SSPC GUIDE 18 2008.02.01
s for Lead-Paint Removal Projects
22 SSPC GUIDE 21 Guide to Evaluation of Slip and Fall Resistance of Flooring Surfaces 2015.05.04
49
4. 주요 규격
번호 구격 번호 제목 날짜
28 SSPC PA 8 Thin-Film Organic Linings Applied in New Carbon Steel Process Vessels - NACE NO. 10 2003.03.15
2015.07.20
29 SSPC PA 9 Measurement of Dry Coating Thickness Using Ultrasonic Gages
(E 2015)
Application of Thick Film Polyurea and Polyurethane Coatings to Concrete and Steel Using Pl
30 SSPC PA 14 2012.09.25
ural-Component Equipment
Material and Preparation Requirements for Steel Test Panels Used to Evaluate the Performanc
31 SSPC PA 15 2013.03.11
e of Industrial Coatings
Method for Evaluating Scribe Undercutting on Coated Steel Test Panels Following Corrosion T
32 SSPC PA 16 2012.09.25
esting
Procedure for Determining Conformance to Steel Profile/Surface Roughness/Peak Count Req 2012.09.25
33 SSPC PA 17
uirements (E 2015)
34 SSPC PA COM Commentary on Paint Application 2004.11.01
1982.11.01
35 SSPC PA GUIDE 4 Guide to Maintenance Repainting with Oil Base or Alkyd Painting Systems
(E 2004)
Guide to Maintenance Coating of Steel Structures in Atmospheric Service - Editorial Revisions
36 SSPC PA GUIDE 5 2002.09.01
November 1, 2004
37 SSPC PA GUIDE 9 Measurement of Dry Coating Thickness on Cementitious Substrates Using Ultrasonic Gages 2008.02.01
38 SSPC PA GUIDE 10 Guide to Safety and Health Requirements for Industrial Painting Projects 2008.08.01
39 SSPC PA GUIDE 11 Protecting Edges, Crevices, and Irregular Steel Surfaces by Stripe Coating 2008.08.01
40 SSPC PA GUIDE 13 Guide for Application of Coating Systems With Zinc-Rich Primers to Steel Bridges 2006.01.01
50
4. 주요 규격
번호 구격 번호 제목 날짜
2006.11.01
41 SSPC PAINT 16 Coal Tar Epoxy Polyamide, Black (or Dark Red) Coating (R 2015)
(E 2015)
2002.04.01
42 SSPC PAINT 20 Zinc-Rich Coating Type I Inorganic and Type II Organic
(E 2004)
1982.11.01
43 SSPC PAINT 23 Latex Primer for Steel Surfaces
(E 2004)
44 SSPC PAINT 24 Latex Semigloss Exterior Topcoat - Editorial Changes 11/1/2004 1982.11.01
1982.11.01
45 SSPC PAINT 27 Basic Zinc Chromate-Vinyl Butyral Wash Primer
(E 2004)
1991.08.01
46 SSPC PAINT 28 Water-Borne Epoxy Primer for Steel Surfaces
(E 2004)
47 SSPC PAINT 29 Zinc Dust Sacrificial Primer, Performance-Based 2002.04.01
2002.04.01
48 SSPC PAINT 30 Weld-Through Inorganic Zinc Primer
(E 2004)
2006.11.01
49 SSPC PAINT 32 Coal Tar Emulsion Coating (R 2015)
(E 2015)
2006.11.01
50 SSPC PAINT 33 Coal Tar Mastic Coating, Cold- Applied (R 2015)
(E 2015)
1996.05.01
51 SSPC PAINT 34 Water-Borne Epoxy Topcoat for Steel Surfaces
(E 2004)
52 SSPC PAINT 36 Two-Component Weatherable Aliphatic Polyurethane Topcoat, Performance-Based 2006.04.01
Single-Component Moisture-Cure Weatherable Aliphatic Polyurethane Topcoat, Performance-
53 SSPC PAINT 38 2006.04.01
Based
51
4. 주요 규격
번호 구격 번호 제목 날짜
54 SSPC PAINT 39 Two-Component Aliphatic Polyurea Topcoat Fast or Moderate Drying, Performance- Based 2004.04.01
52
4. 주요 규격
번호 구격 번호 제목 날짜
Latex Painting System for Industrial and Marine Atmospheres, Performance- Based - Editorial
68 SSPC PS 24.00 1991.08.01
Revisions November 1, 2004
Aluminum Pigmented Epoxy Coating System Materials Specification, Performance-Based Type
69 SSPC PS 26.00 I, for Use Over Blast Cleaned Steel Type II, for Use Over Hand Cleaned Steel - Editorial Revisio 2000.06.01
ns November 1, 2004
Alkyd Coating System Materials Specification, Performance-Based - Editorial Revisions Novem
70 SSPC PS 27.00 2000.06.01
ber 1, 2004
Two-Coat Zinc-Rich Polyurethane Primer/Aliphatic Polyurea Topcoat System, Performance-Bas
71 SSPC PS 28.01 2009.04.01
ed
72 SSPC PS 28.02 Three-Coat Moisture-Cured Polyurethane Coating System, Performance-Based 2010.06.01
74 SSPC PS GUIDE 7.00 Guide for Selecting One-Coat Shop Painting Systems - Editorial Revisions November 1, 2004 1982.11.01
75 SSPC PS GUIDE 8.00 Guide to Topcoating Zinc-Rich Primers - Editorial Revisions November 1, 2004 2002.04.01
53
4. 주요 규격
번호 구격 번호 제목 날짜
81 SSPC QP 3 Certification Standard for Shop Application of Complex Protective Coating Systems 2010.09.23
Standard Procedure for Evaluating the Qualifications of Contractors Disturbing Hazardous Co 1997.05.01
82 SSPC QP 4
atings During Demolition and Repair Work (E 2004)
83 SSPC QP 5 Standard Procedure for Evaluating Qualifications of Coating and Lining Inspection Companies 2012.07.16
Standard Procedure for Evaluating the Qualifi cations of Contractors Who Apply Thermal Spra 2004.07.01
84 SSPC QP 6
y (Metallizing) for Corrosion Protection of Steel and Concrete Structures (E 2007)
2003.05.01
85 SSPC QP 7 Procedure for Evaluating Painting Contractors With Limited Industrial Work Experience
(E 2004)
Standard Procedure for Evaluating the Qualifications of Contracting Firms That Install Polyme
86 SSPC QP 8 2003.07.01
r Coatings and Surfacings on Concrete and Other Cementitious Substrates
Standard for Evaluating Qualifications of Painting Contractors Who Apply Architectural Paints
87 SSPC QP 9 2008.08.01
and Coatings
88 SSPC QP COM COMMENTARY ON QUALIFICATION PROCEDURES 2015.07.17
Standard Procedure for Evaluating a Coating Contractor’s Advanced Quality Management Sys
89 SSPC QS 1 2015.03.02
tem
2015.04.23
90 SSPC SP 1 Solvent Cleaning
(E 2016)
1982.11.01
91 SSPC SP 2 Hand Tool Cleaning (E 2000)
(E 2004)
1982.11.01
92 SSPC SP 3 Power Tool Cleaning
(E 2004)
93 SSPC SP 5 White Metal Blast Cleaning 2007.01.01
54
4. 주요 규격
번호 구격 번호 제목 날짜
105 SSPC SYSTEM BOOK Systems and Specifications Steel Structures Painting Manual Volume 2 2000.01.01
106 SSPC TR 1 Thermal Pre- Cleaning - NACE 6G194; Editorial Revisions November 1, 2004 1994.10.01
1998.05.01
107 SSPC TR 2 Wet Abrasive Blast Cleaning - NACE 6G198
(E 2004)
55
4. 주요 규격
번호 구격 번호 제목 날짜
Dehumudification and Temperature Control During Surface Preparation, Application, and Curi
108 SSPC TR 3 ng for Coatings/Linings of Steel Tanks, Vessels, and Other Enclosed Areas - NACE 6A192 (200 2000.12.01
0 Revision)
109 SSPC TR 4 Preparation of Protective Coating Specifications for Atmospheric Service - NACE 80200 2000.12.01
Design, Installation, and Maintenance of Protective Polymer Flooring Systems for Concrete -
110 SSPC TR 5 2003.11.01
NACE 02203
1995.07.01
111 SSPC TU 1 Surface Tolerant Coatings for Steel
(E 2004)
Informational Report and Technology Update - Design, Installation, and Maintenance of Coati
112 SSPC TU 2 1997.02.01
ng Systems for Concrete Used in Secondary Containment - NACE 6G197
1997.05.01
113 SSPC TU 3 Overcoating
(E 2004)
1999.05.01
114 SSPC TU 5 Accelerated Testing of Industrial Protective Coatings
(E 2004)
1999.05.01
115 SSPC TU 6 Chemical Stripping of Organic Coatings from Steel Structures
(E 2004)
CONDUCTING AMBIENT AIR, SOIL, AND WATER SAMPLING OF SURFACE PREPARATION AND
116 SSPC TU 7 2015.05.04
PAINT DISTURBANCE ACTIVITIES
2001.02.01
117 SSPC TU 8 The Use of Isocyanate- Containing Paints as Industrial Maintenance Coatings
(E 2004)
118 SSPC TU 9 Estimating Costs for Protective Coatings Projects - Editorial Revisions November 1, 2004 2001.03.01
2002.12.01
119 SSPC TU 10 Procedures for Applying Thick Film Coatings and Surfacings Over Concrete Floors
(E 2004)
120 SSPC TU 11 Inspection of Fluorescent Coating Systems 2010.12.01
56
4. 주요 규격
번호 구격 번호 제목 날짜
122 SSPC V1 Good Painting Practice: Painting Manual Volume 1 - Fifth Edition 2016.01.01
123 SSPC V1 & V2 SET Steel Structures Painting Manual: Volume 1 and Volume 2 - Volume 1 is 2002 2005.01.01
124 SSPC V2 SYSTEMS AND SPECIFICATIONS: STEEL STRUCTURES PAINTING MANUAL VOLUME 2 2011.01.01
Guide and Reference Photographs for Steel Surfaces Prepared by Dry Abrasive Blast Cleaning 2002.06.01
125 SSPC VIS 1
– TEXT ONLY (E 2004)
Standard Method of Evaluating Degree of Rusting on Painted Steel Surfaces - Editorial Revisi
126 SSPC VIS 2 2000.06.01
ons November 1, 2004; Text Only
Guide and Reference Photographs for Steel Surfaces Prepared by Power- and Hand- Tool Cle
127 SSPC VIS 3 2004.07.01
aning - Text Only
Guide and Reference Photographs for Steel Surfaces Prepared by Waterjetting - NACE VIS 7; 2002.06.01
128 SSPC VIS 4
Text Only (E 2004)
Guide and Reference Photographs for Steel Surfaces Prepared by Wet Abrasive Blast Cleaning 2001.06.01
129 SSPC VIS 5
– NACE VIS 9; Text Only (E 2004)
57
4. 주요 규격
해외 선급 단체
Lloyd’s Register of Shipping
영국 선급 협회
미국 선급 협회
일본 선급 협회
58
4. 주요 규격
해외 선급 단체
Korean Register of Shipping
한국 선급 협회
■ 주요 규격
- 선급 및 강선 규칙
- 선급 및 강선 규칙 적용 지침
노르웨이 선급 협회
Bureau Veritas
프랑스 선급 협회
59
5. 각국 공업 규격
각국 공업 규격
Number Title
60
5. 각국 공업 규격
각국 공업 규격
Number Title
61
5. 각국 공업 규격
각국 공업 규격
Number Title
ASHRAE American Society of Heating, Refrigerating and Air conditioning Engineers, U.S.A
62
5. 각국 공업 규격
각국 공업 규격
Number Title
63
5. 각국 공업 규격
각국 공업 규격
Number Title
64
5. 각국 공업 규격
각국 공업 규격
Number Title
65
5. 각국 공업 규격
각국 공업 규격
Number Title
66
5. 각국 공업 규격
각국 공업 규격
Number ETitle
67
5. 각국 공업 규격
각국 공업 규격
Number Title
68
5. 각국 공업 규격
각국 공업 규격
Number Title
69
6. 국가 및 단체 표준
국가 및 단체 표준
구분 표준 약호 표준/표준화 기구 명칭
70
6. 국가 및 단체 표준
국가 및 단체 표준
구분 표준 약호 표준/표준화 기구 명칭
ANSI American National Standards Institute (미국)
71
6. 국가 및 단체 표준
국가 및 단체 표준
구분 표준 약호 표준/표준화 기구 명칭
NEN
Nederlandse Norm (네덜란드)
NF
Norme Francaise (프랑스)
NZS
Newzealand Standards (뉴질랜드)
ONORM
Osterreichische Norm (오스트리아)
국가 표준
SABS
South African Bureau of Standards (남아프리카공화국)
SIS
Svensk Standards (스웨덴)
SS
Singapore Standards (싱가포르)
UNI
Unificazione Italiano (이태리)
72
6. 국가 및 단체 표준
국가 및 단체 표준
구분 표준 약호 표준/표준화 기구 명칭
73
6. 국가 및 단체 표준
국가 및 단체 표준
구분 표준 약호 표준/표준화 기구 명칭
74
6. 국가 및 단체 표준
국가 및 단체 표준
구분 표준 약호 표준/표준화 기구 명칭
75
6. 국가 및 단체 표준
국가 및 단체 표준
구분 표준 약호 표준/표준화 기구 명칭
UL Underwriters Laboratories
76
77/3