Professional Documents
Culture Documents
Design of Single Stage JFET Amplifier
Design of Single Stage JFET Amplifier
We select voltage divider(P.D) bias circuit as it provides stable quiescent point against device parameter variations
Vgs = Vp * (1 - sqrt(Id/Idss))
Calculate Vgs max by substituting Vp max, Id max & Idss max inVgs
Similarly calculate Vgs min
Step 4: Selection of Rs
Step 5: Selection of Rd
If RL is given
RL' = (rd) parallel (Rd) parallel (RL)
If RL is not given
assume RL = infinity
RL' = (rd) parallel (Rd)
[If required gain(Av) is greater than a specified value, select higher std value]
[If required gain(Av) is equal to a specified value, select nearest standard value]
Step 6: Selection of Vdsq
Assume Vo = 1.5 V
Vdsq = 1.15 * (mod(Vp typ) + Vo peak)
Also
Vg = Vdd * R2/(R1 + R2)
[Find R1 in terms of R2 & assume R2 = 1 M ohm & calculate R1]
Selection of Cg:
[FL = lower cutoff frequency.AssumeFL = 20 Hz (For all capacitors)if not specified. Voltage ratings of capacitors >
Vdd]
Selection of Cd:
Selection of Cs:
Step 4: Selection of Rs
Rs = (mod(Vgsq)/(Idq)
Step 5: Selection of Rd
If RL is given
RL' = (rd) parallel (Rd) parallel (RL)
If RL is not given
assume RL = infinity
RL' = (rd) parallel (Rd)
[If required gain(Av) is greater than a specified value, select higher std value]
[If required gain(Av) is equal to a specified value, select nearest standard value]
Assume Vo = 1.5 V
Vdsq = 1.15 * (mod(Vp typ) + Vo peak)
Step 7: Selection of Vdd
Step 8: Selection of Rg
Assume Rg = 1 M ohm
Selection of Cg:
[FL = lower cutoff frequency.AssumeFL = 20 Hz (For all capacitors)if not specified. Voltage ratings of capacitors >
Vdd]
Xcg = (Rg)
Cg = 1/(2 * pi * FL * Xcg)
Selection of Cd:
Selection of Cs:
Step 4: Selection of Rs
Vgsq = - Idq * Rs
hence
Rs = mod(Vgsq/Idq)
[Select nearest std value]
Step 5: Selection of Rd
If RL is given
RL' = (rd) parallel (Rd) parallel (RL)
If RL is not given
assume RL = infinity
RL' = (rd) parallel (Rd)
[If required gain(Av) is greater than a specified value, select higher std value]
[If required gain(Av) is equal to a specified value, select nearest standard value]
Step 8: Selection of Rg
Assume Rg = 1 M ohm
Selection of Cg:
[FL = lower cutoff frequency.AssumeFL = 20 Hz (For all capacitors)if not specified. Voltage ratings of capacitors >
Vdd]
Xcg = (Rg)
Cg = 1/(2 * pi * FL * Xcg)
Selection of Cd:
Selection of Cs:
Graphical method
[In graphical methord draw the graph of Ids against Vds [Values given in data sheet.You will be given the value/s of
or range of Ids (2 values(max or min) or range of values for device parameter variation & single value(typ) for other
methods)]
[Plot the required value/s of Vgs & find Vgsq & continue with the usual method. The answers in the 2 methods will
differ a lot for the same problem. For device parameter variation use max & min curve to calculate Vgs max & min
resp. For other methods use typ curve unless mentioned otherwise ]