Professional Documents
Culture Documents
Polybond PVA: PVA Based Bonding Agent and Admixture
Polybond PVA: PVA Based Bonding Agent and Admixture
CHARACTERISTICS
► Bonds to most common construction material except
PVC rubber and similar products
► Versitile
► Enhances adhesion
► Increases strength
TDS_Polybond PVA_GCC_0519
bonding
FIELDS OF APPLICATION
– Adhesive
Polybond PVA bonds with almost all kinds of building
materials except PVC, rubber and polyethylene. When
added with suitable filler, it can be used for fixing 1
plasterboard, ceramic tiles, marbles etc.
– Bonding Agent
Polybond PVA gives mortars, especially topping mortars as an adhesive for fixing plaster boards, polystyrene tiles.
enhanced bond strength. The wear resistance of screed To ceiling and walls. If the surface is highly porous, apply a
treated with Polybond PVA is improved than that of a primer coat of Polybond PVA mixed with water in the ratio
conventional sand and cement screed. The topping will of 1:3.
be dust free, wear, water, oil and grease resistant As a bonding agent for screeds, plasters and renders
– Admixture The surface shall be sound and free from all contaminants,
Polybond PVA has a plasticizing effect which improves such as oil, grease, paint etc. Sealing of the surface is done
mortar application, increases the mechanical strength of with 1 part of Polybond PVA with 3 parts of water. Apply
screeds and renders, reduces shrinkage and has perfect the bonding coat followed by the application of the render,
adhesion even on smooth concrete screed or plaster normally. The same method shall be used
– Surface sealer to bond new to old concrete.
Polybond PVA can be used as a surface sealer for As an admixture
concrete and floors to minimize the dusting and For normal to heavy duty flooring, 20-30L of Polybond PVA
penetration of oils. It can be used as an effective primer is the recommended to be admixed with100 kg cement.
on certain decorative coatings
For heavy renderings and cementitious toppings
DESCRIPTION Seal and prime the surfaces with Polybond PVA diluted with
Polybond PVA is a polyvinyl acetate based polyvinyl alcohol 3 parts of water. Prepare the render coat with 1 part of
suspension used as a surface sealer, bonding agent and ordinary portland cement, 1 part clean washed sand and 1
admixture for cement and mortar. part of Polybond PVA to 3 parts of clean water. Apply this to
the tacky prime coat. 10 to 15L of Polybond PVA per 100
APPLICATION INSTRUCTIONS kg cement is recommended.
Note: Stir the contents of the product thoroughly, before
As an adhesive for uneven surfaces
use
Make a paste of Polybond PVA diluted with equal amount
of water, cement and fine sand. The paste can be applied
LIMITATIONS: DOSAGE
– not recommended where permanent dampness occurs. As an admixture
– do not use below 5°C Floor screeds/topping 20-30L of Polybond
– do not over towel PVA per 100 kg cement
i.e. 100-150L /m3 of
CLEANING mortar approximately
Clean all the tools with water immediately after use. Render coat 10-15L /100 kg cement
As a Primer /adhesive / bonding coat
STORAGE & SHELF LIFE
Neat 1L / 10 m2
Store in a cool, dry place and keep away from all sources dilute1:1 1L / 20 m2
of heat and sunlight. In tropical climates, store in air
dilute1:3 10-15L / 35m2
condition rooms. The shelf life is up to 12 months in un-
opened condition and if stored as per recommendations. These values will vary according to the degree of porosity
Excessive exposure to sunlight, humidity and UV will result and texture of the surface.
in the deterioration of the quality of the product and reduce TECHNICAL SPECIFICATION
its shelf life.
PROPERTIES VALUES Test Standards
HEALTH & SAFETY Appearance White viscous liquid -
As with all construction chemical products, caution should Solid content, [%] 30±3 ASTM D 2939
always be exercised. Protective clothing such as gloves pH 6-7.5 BS EN ISO 787
and goggles should be worn. Treat any splashes to the Specific gravity 1.05±0.05 ASTM D 1475
skin or eyes with fresh water immediately. Should any of Application temperature,
the products be accidentally swallowed, do not induce [°C] 5 to 45 -
TDS_Polybond PVA_GCC_0519