Professional Documents
Culture Documents
Ec Centrifugal Fans - Radipac: Backward Curved, Single Inlet
Ec Centrifugal Fans - Radipac: Backward Curved, Single Inlet
Highlights:
– 7-blade fan, 3-phase fan motor
– Output: 10 VDC, max.10 mA, 20 VDC, max. 50 mA, slave 0-10 V
– Input: sensor 0-10 V or 4-20 mA, 24 V external programming, 0-10 VDC/ PWM control
– Integrated PID controller along with RS485 MODBUS RTU technology
– Over-temperature protected electronics / motor
– Soft start, alarm relay, motor current limit, PFC passive, line undervoltage / phase failure detection
– Control interface with SELV potential safely disconnected from the mains
Material: Impeller: Aluminum sheet
Rotor: Coated in black
Electronic housing: Die-cast aluminum
Assembly: Galvanized steel with aluminum posts
Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
Condensate discharge holes: Rotor-side
Direction of rotation: Clockwise, seen on rotor
Speed (1)
Air flow
Mass
Nominal Data
UL
Type RadiPac Motor CFM VAC Hz Watts RPM A °C lbs
R3G400-AQ29-19 EG1R-240-400-39 M3G150-FF 5,285 200...240 50/60 3,100 2,550 8.4 -25...50 48 IP54 A Yes
R3G400-AQ23-09 EG1R-480-400-39 M3G150-FF 5,227 380...480 50/60 3,000 2,550 4.0 -25...60 48 IP54 A Yes
(1) Nominal data at maximum load.
n Pe I I LwAin
Curves A A
rpm W (460V) (230V) dB(A)
6.00
Measurement: LU-121371 A 1 2550 1972 2.6 5.7 93
in. wg
3
accidental contact. A 4 2550 2792 3.7 7.9 88
Suction-side noise levels: LWA as
A 5 2100 1103 1.5 3.1 89
per ISO 13347, LPA measured at
4.00
4.00
1m distance to fan axis. A 6 2100 1517 2.0 4.2 83
8
The values given are valid A 7 2100 1668 2.2 4.6 81
7 under the measuring conditions
A 8 2100 1555 2.1 4.4 84
3.00
3.00 2 mentioned and may vary accoring
to the actual installation situation. A 9 1700 585 0.8 1.6 84
12
With any deviation to the standard A 10 1700 805 1.1 2.2 78
11
6
set-up, the specific values have
2.00
to be checked and reviewed once A 11 1700 885 1.2 2.5 76
installed or fitted. A 12 1700 825 1.1 2.3 79
16
10
15
For detailed information on the
measuring set-up, please contact
A 13 1300 262 0.3 0.7 78
1.00
1.00
14
ebm-papst. A 14 1300 360 0.5 1.0 72
A 15 1300 396 0.5 1.1 71
13 9 5 1
0.00 A 16 1300 369 0.5 1.0 73
Δpfa
0v 1000
1000 2000
2000 3000
3000 4000
4000 5000
5000 cfm600
R3G400-AQXX-XX Dimensions shown in inches (mm)
2.76(70)
Ø11.10+0.1(282+2.5)
Ø9.13(232)
Ø17.91(455)
Tightening torque
31 +4.4 lbf-in (3.5 +0.5 Nm)
17.72(450) 12.64(321)
Ø0.28(7.1)
4 places
16.54(420)
19.69(500)
16.00(406.5)