Professional Documents
Culture Documents
Strenx Tube 700MH PDF
Strenx Tube 700MH PDF
Dimensions
Circular
Diameter 2.0mm (kg/m) 3.0mm (kg/m) 4.0mm (kg/m) 5.0mm (kg/m) 6.0mm (kg/m) 8.0mm (kg/m) 10.0mm
(kg/m)
42.4 mm 1.99
Square
Height x Width 2.0mm (kg/m) 3.0mm (kg/m) 4.0mm (kg/m) 5.0mm (kg/m) 6.0mm (kg/m) 8.0mm (kg/m) 10.0mm
(kg/m)
30 x 30 mm 1.68
40 x 40 mm 2.31 3.30
50 x 50 mm 2.93 4.25
60 x 60 mm 3.56 5.19 6.71
70 x 70 mm 6.13 7.97 9.70
80 x 80 mm 7.07 9.22 11.3
90 x 90 mm 10.5 12.8
100 x 100 mm 11.7 14.4 17.0 21.4
120 x 120 mm 14.3 17.6 20.8 26.4
140 x 140 mm 16.8 20.7 24.5 31.4 38.1
150 x 150 mm 18.0 22.3 26.4 34.0 41.3
160 x 160 mm 23.8 28.3 36.5 44.4
180 x 180 mm 27.0 32.1 41.5 50.7
200 x 200 mm 35.8 46.5 57.0
220 x 220 mm 39.6 51.5 63.2
250 x 250 mm 45.2 59.1 72.7
300 x 300 mm 71.6 88.4
Recommended minimum batch sizes on mill orders.
60 x 40 mm 2.93 4.25
70 x 50 mm 3.56 5.19 6.71
80 x 40 mm 3.56 5.19 6.71
80 x 60 mm 6.13 7.97
90 x 50 mm 6.13 7.97
100 x 50 mm 6.60 8.59
100 x 60 mm 7.07 9.22
100 x 80 mm 10.5
120 x 60 mm 10.5 12.8
120 x 80 mm 11.7 14.4 17.0 19.4
150 x 100 mm 14.9 18.3 21.7 27.7
160 x 80 mm 14.3 17.6 20.8 26.4
180 x 100 mm 16.8 20.7 24.5 31.4 38.1
200 x 100 mm 18.0 22.3 26.4 34.0 41.3
200 x 120 mm 23.8 28.3 36.5 44.4
250 x 100 mm 31.11 40.23 49.11
250 x 150 mm 35.8 46.5 57.0
260 x 180 mm 39.6 51.5 63.2
300 x 200 mm 45.2 59.1 72.7
400 x 200 mm 71.6 88.4
Recommended minimum batch sizes on mill orders.
Data sheet 2040 Strenx® Tube 700MH 2017-04-20
Mechanical Properties
Yield strength Rp0.2 Tensile Strength Rm Elongation A 52) Charpy-V -20°C 10x10 mm test
(min MPa) (MPa) (min %) specimen 1)
(min J)
700 750- 950 10 40
Mechanical properties meet the requirements of prEN 10219 (2016).
The mechanical properties for rectangular hollow sections are tested by SSAB on the longer side of the cross section.
1)
Impact testing according to EN ISO 148-1 is performed on thicknesses ≥ 6mm. The specified minimum value corresponds to a full-size specimen.
2)
The hollow sections with D/T < 15 (round) or (B + H)/2T < 12,5 (rectangular and square), the minimum value of elongation is reduced by 2.
Tolerances
Characteristic Circular hollow sections
Tolerances meet or exceed the requirements of EN 10219
Outside diameter (D) 1) ±1%, however a minimum of ±0.5 mm and a maximum of ±10 mm
Out-of-roundness 2%, when D/T ≤ 100
Thickness (T) When D ≤ 323.9 mm: -5%/+10%, with a minimum of ±0.2 mm and
maximum ±0.5 mm
When 355.6 ≤ D ≤ 406.4 mm3): ±10%, when T ≤ 5 mm / ±0.5 mm,
when T > 5 mm
When D > 406.4 mm3): ±10%, with a maximum of ±2 mm
Straightness 0.20% of total length and 3 mm over any 1 m length
Mass per unit length Individual tube: ±6%
Mill length 0/+50 mm, 6000 ≤ L ≤ 12000- 18000 mm (standard lengths 6000 &
12000 mm)
Delivery Conditions
The tubes are cold formed and high frequency welded from thermomechanically rolled steel.
Contact Information
www.ssab.com/contact
Data sheet 2040 Strenx® Tube 700MH 2017-04-20
The English version of this document shall prevail in case of discrepancy. Minor changes and updates to the document may occur, please download the latest version of this docu-
ment at www.ssab.com
SSAB, Strenx, Hardox, Docol, GreenCoat, Toolox, Armox, Ramor, SSAB Domex, SSAB Laser, Raex, Duroxite are trademarks owned by the SSAB group of companies.