Professional Documents
Culture Documents
Kennedy Valve/UL/FM Butterfly Valves 11-1
Kennedy Valve/UL/FM Butterfly Valves 11-1
Kennedy Swing Check Valves are designed and manufactured in conformance with A.W.W.A. C508 and are for
use on water, oil and gas lines. Under certain circumstances where it is desirable to have more positive control of
the closing of the disc, the valves can be supplied with either lever-and-spring or lever-and-weight. For restricted
spacing requirements Kennedy Valve manufactures a Wafer Check Valve that also helps to control water hammer.
Features
Swing Check Valve-AWWA
• Stainless steel hinge pin.
• Working parts are removable through the top of the valve.
• Tapped bosses available.
• Available with lever-and-spring or lever-and-weight.
• Double bronze side plug construction.
• Bodies are made of high strength cast iron with reinforced
flanges ‑ ANSI B 16.1/125 # flanges.
• May be installed in a vertical line with the flow up.
• Figure #1106 Series 2"-12"
Test Pressure ‑ Seat and Shell 400 PSI
Working Pressure ‑ non-shock CWP 200 PSI
• Figure #106 Series 14"-24"
Test Pressure ‑ Seat and Shell 300 PSI
Working Pressure ‑ non-shock CWP 150 PSI
FIGURE #1106/1106A/1106LW/1106LS/1106AW/1106AS
* **See Q on page 6.
** *Denotes that part is available only as part of an assembly.
*** Cast inegral (2"-3").
SIZE A B C D E F G H J L M N Q* R
2" 8.00 0.65 6.00 6.00 6.56 5.00 4.72 .50 0.34 4.75 4 .75 4 10.0
21/2" 8.50 .069 7.00 6.44 6.56 5.25 4.94 .50 0.41 5.50 4 .75 4 8.0
3" 9.50 0.78 7.50 6.85 6.56 6.00 5.34 .50 0.44 6.00 4 .75 4 8.0
4" 11.50 1.00 9.00 8.69 9.00 7.75 8.19 .62 0.41 7.50 8 .75 4 12.0
6" 14.00 1.03 11.00 10.51 11.00 9.75 9.00 .75 0.43 9.50 8 .87 4 15.0
8" 19.50 1.25 13.50 12.56 13.50 14.13 10.18 .87 0.75 11.75 8 .87 4 15.0
10" 24.50 1.31 16.00 14.07 16.75 18.00 11.62 1.00 0.81 14.25 12 1.00 6 15.0
12" 27.50 1.38 19.00 16.13 19.00 18.00 13.75 1.00 0.87 17.00 12 1.00 6 15.0
BODY MARKINGS
(ONE SIDE) (OPPOSITE SIDE)
A.W.W.A. FIG. NO.
KENNEDY 200 W
CAP MARKINGS
YEAR
KENNEDY
SIZE
F
PLAIN CHECK VALVE
14"
LEVER AND WEIGHT CHECK STYLE NO. 59-02/106A
VALVE
STYLE NO. 159-02/106ALW
15-5
PART NO. A.S.T.M.
NO. REQ’D PART MATERIAL SPEC. NO.
15-6
1 1 Body Cast Iron A-126 CL B
2 1 Cover Cast Iron A-126 CL B
3 1 Body Ring Bronze CDA84400
4 1 Clapper Cast Iron A-126 CL B
5 1 Clapper Arm Bronze CDA86400
6 Varies Lockwasher Steel —
7 Varies Capscrew Bronze B-21
8 1 Hinge Pin Stn. Stl. A-276-303
9 2 Gland (Bronze Bushed) Cast Iron A-126CL. B
10 Varies Cover Bolt and Nuts Steel A-307GR B
11 1 Cover Gasket Non-Asbestos —
12 1 Clapper Ring Neoprene —
13 1 Ring Clamp Bronze CDA84400
14 Varies Ring Clamp Capscrew Bronze B-21
17
15 1 Weight Lever Arm Bronze B-62
16 1 Weight Cast Iron A-126CL. B
18 22 17 1 Spring Lever Arm Bronze B-62
20 18 1 Spring Steel —
19 1 Spring Bracket Steel —
19
20 1 Spring Eyebolt Steel A-307GR.B
21 1 Cap Plate Cast Iron A-126CL. B
13
1
Fig. 1126 Bronze Faced Disc Assembly Sizes 4" through 14"
14 “O” Rings Buna “N”
15 Disc Bolt Bronze Rod B-16
17 Hinge Malleable Iron A-47
18 Disc Malleable Iron A-47
19 Disc Ring Bronze B-62*
*Cannot be ordered separately.
WEIGHT ‑ POUNDS
SIZE 21/2" 3" 4" 5" 6" 8" 10" 12"
FIG. 126 52 62 114 145 193 319 475 680
FIG. 126A 53 62 117 145 196 322 480 685
Exploded View
A FIG. 1126 Bronze Disc Assembly, Size 2 1/2" and 3" Center
B FIG. 1126 Bronze Faced Disc Assembly, Size 4" thru 12" Bottom
C FIG. 1126A Rubber Disc Assembly, Size 4" thru 12"
– FIG. 1126A Rubber Disc Assembly, Size 2 1/5" and 3" - Not Shown
See Page 15-8 for Detail. Also see Page 15-8 for Number Identification
BODY MARKINGS
(ONE SIDE) (OPPOSITE SIDE)
size–300 kennedy
706 year
Features
Wafer Check Valve-UL/FM
• Short laying length.
• Spring loaded for more effective control of water
hammer.
• Stainless steel spring.
• Resilient seating.
• Easy maintenance with a minimum number of parts.
• Built-in O-Ring flange seals ‑ gaskets not required.
• Mounts between standard ANSI B 16.1/125 lb.
flanges. Mounting between 250 lb. flanges requires
use of spacers.
• May be installed in a vertical line with flow up or
down.
• Testing
Test Pressure ‑ Seat and Shell ‑ 600 PSI
Working Pressure ‑ Non-Shock ‑ 300 PSI
• Figure #706
Compact, for installation between standard flanges, Kennedy WAFER CHECK VALVES have spring loaded bronze
discs, resilient seating, and utilize “O” rings rather than gaskets for end seals.
UL LISTED/FM APPROVED
ULC LISTED
fig. 706
WT.
Size A B C D E LBS. F G WT.
4 3.75 4.03 6.87 1.34 3.03 15 1.50 2.19 15
6 3.75 6.06 8.75 1.53 4.56 23 3.50 2.13 23
8 4.25 7.98 11.00 1.92 6.00 39 5.50 2.50 39
The Kennedy Figure 426 Grooved End Swing Check Valve is a lightweight unit that features a top access cover for
field maintenance. The valves are intended to be easily installed with approved grooved couplings. They may be
installed either with the flow in a vertical position or horizontally. All valves have a 1/2" NPT connection on the inlet
side for installation of a 1/2" Ball drip.
PARTS LIST
ITEM NO. QTY. PART NAME MATERIAL
1 1 Valve Body Ductile Iron
2 3 Nut Plated
3 1 Cover Cast Iron
4 3 Bolt Plated
5 1 Cover Seal SBR Duro 55-65
6 1 Hinge Support Stainless Steel
7 2 Nut Stainless Steel
8 2 Washer Red Fiber
9 2 Hinge Support Bolt Stainless Steel
10 1 Hinge Pin Stainless Steel
11 1 Hinge Stainless Steel
12 1 Valve Disk EPDM
13 1 Disk Plate Stainless Steel
14 1 Disk Holder Cast Iron *
15 1 Disk Nut Stainless Steel
16 1 Seal Washer Red Fiber **
17 1 Disk Bolt Stainless Steel
18 1 Seat Ring Tin Plated Bronze
19 1 Drain Plug Zinc Plated
**6 and 8 in. sizes only (others are integral to hinge)
**2.5, 3 and 4 in. sizes only
DIMENSIONAL DATA
Height Width
A B
2.5" = 7.22 8.625
3" = 7.68 9.120
4" = 8.54 9.990
6" = 11.34 13.280
8" = 12.86 14.500
Weight/Pounds
2.5" = 19 lb.
3" = 21 lb.
4" = 29 lb.
6" = 61 lb.
8" = 81 lb.
ITEM
NO. DESCRIPTION
1 Body Gray Iron A126 B Special Boss Drill & Tap
2 Cap Gray Iron A126 B
3 Cap Gasket Rubber Reinforced by GARLOCK
4 Cap Bolts & Nuts Steel, Plated A307
5 Seat Ring Bronze CDA 844
6
7 Stuffing Box Bronze B16
8 Packing (not shown) Non-Asbestos by GARLOCK
9 Gland Follower Bronze B16
10 Hinge (Keyed) Ductile Iron
11M Disc – Metal Iron
11R Disc Holder Iron
12M Disc Facing Ring Bronze CDA 844 Intergral with Disc
12R Disc, Resilient Rubber
13R Disc Plate Bronze CDA 844
14 Disc Bolt — Sizes 2-8" Steel 10&12" Bronze
15 Nut, Disc Bolt — Sizes 2-8" Steel 10&12" Bronze
16 Disc Bolt Gasket Fibre 10&12" Sizes Use O-Ring
17 Hinge Pin (Special) Stainless 431 Heat Treated
18 Lever (Special) Steel
19 Key for Lever Stainless
SIZE A D E CC1 CC2 CC3 CC4 CC5 CC6 CC7
20 Set Screw for Lever Steel
21 Key for Hinge Stainless 4 11.50 8.31 9.00 13.77 12.00 9.56 2.44 — 3.75 8.89
22 Weight Gray Iron A126 B 6 14.00 10.06 11.00 19.28 18.00 10.38 3.31 — 5.00 7.52
23 Set Screw for Weight Steel, Plated A307 8 19.50 12.38 13.50 22.24 18.00 11.75 4.88 — 6.25 6.40
24 Cylinder Arm Steel 10 24.50 13.93 16.75 23.62 18.00 13.68 6.19 — 7.12 11.46
25 Set Screw for Arm Steel
12 27.50 16.18 19.00 24.57 18.00 14.94 8.38 — 8.19 10.40
26 Body Bracket Steel
27 Outer Cylinder Bracket Steel Dimensions Approximate–For Checking Clearances Only
28 Inner Cylinder Bracket Steel 4 & 6" Sizes Allow Clearance Two Sides to Remove Side Plug & Access Hinge Pin
29 Cylinder Per Catalogue
30 Bushing(s) Bronze
31 Rod End Steel
32 Pin Steel
33 Cotter Pin Stainless
34 Control Valve Per Catalogue
35 Nipple Brass ASSEMBLY DRAWING CUSHION CHECK SIZES 4"-12"
36 Muffler Per Catalogue FLOW HORIZONTAL
37 Body Bracket Bolts Steel, Plated Grade 5 DRAWN BY L2C DATE 9/15/96
38 Cylinder Bracket Bolts Steel, Plated Grade 5 none
CHECKED
APPRoVED
Kennedy
SCALE
39 Lock Washer (HiCollar) Steel, Plated
40 Nuts (Jam) Steel, Plated
Valve DWG
No. 54106
REV.
In some cases the customer may want an arrangement that retards the closing of the check valve. The customer
may want such an arrangement for those cases where the water column actually has an opportunity to reverse or
even separate, such as might occur when the check valve is not at the lowest elevation in the system.
ITEM
NO. DESCRIPTION
1 Body Gray Iron A126 B Special Boss Drill & Tap
2 Cap Gray Iron A126 B
3 Cap Gasket Rubber Reinforced by GARLOCK
4 Cap Bolts & Nuts Steel, Plated A307
5 Seat Ring Bronze CDA 844
6
7 Stuffing Box Bronze B16
8 Packing (not shown) Non-Asbestos by GARLOCK
9 Gland Follower Bronze B16
10 Hinge (Keyed) Ductile Iron
11M Disc – Metal Iron
11R Disc Holder Iron
12M Disc Facing Ring Bronze CDA 844 Intergral with Disc
12R Disc, Resilient Rubber
13R Disc Plate Bronze CDA 844
14 Disc Bolt — Sizes 2-8" Steel 10&12" Bronze
15 Nut, Disc Bolt — Sizes 2-8" Steel 10&12" Bronze
16 Disc Bolt Gasket Fibre 10&12" Sizes Use O-Ring
17 Hinge Pin (Special) Stainless 431 Heat Treated
18 Lever (Special) Steel
19 Key for Lever Stainless
SIZE A D E VC1 VC2 VC3 VC4 VC5 VC6 VC7
20 Set Screw for Lever Steel
21 Key for Hinge Stainless 4 11.50 8.31 9.00 8.00 12.00 9.56 2.44 9.69 3.75 8.89
22 Weight Gray Iron A126 B 6 14.00 10.06 11.00 11.00 18.00 10.38 3.31 10.21 5.00 7.52
23 Set Screw for Weight Steel, Plated A307 8 19.50 12.38 13.50 12.00 18.00 11.75 4.88 11.69 6.25 6.40
24 Cylinder Arm Steel
10 24.50 13.93 16.75 NA 18.00 13.68 6.19 13.13 7.12 11.46
25 Set Screw for Arm Steel
26 Body Bracket Steel
12 27.50 16.18 19.00 NC 18.00 14.94 8.38 15.25 8.19 10.40
27 Outer Cylinder Bracket Steel Dimensions Approximate–For Checking Clearances Only
28 Inner Cylinder Bracket Steel 4 & 6" Sizes Allow Clearance Two Sides to Remove Side Plug & Access Hinge Pin
29 Cylinder Per Catalogue
30 Bushing(s) Bronze
31 Rod End Steel
32 Pin Steel
33 Cotter Pin Stainless
34 Control Valve Per Catalogue
35 Nipple Brass ASSEMBLY DRAWING CUSHION CHECK SIZES 4"-12"
36 Muffler Per Catalogue FLOW UP
37 Body Bracket Bolts Steel, Plated Grade 5 DRAWN BY L2C DATE 9/15/96
38 Cylinder Bracket Bolts Steel, Plated Grade 5 Kennedy APPRoVED
none
CHECKED SCALE
39 Lock Washer (HiCollar) Steel, Plated
40 Nuts (Jam) Steel, Plated Valve
DWG
No. 54107V
REV.
For those customers, Kennedy Valve makes available the Figure 1206 Cushion Check Valve. The Figure 1206
Cushion Check Valve is a Figure 1106, AWWA valve with a lever and weight and a pneumatic cylinder arrange-
ment. The pneumatic cylinder has a needle valve that allows the customer to adjust the time required for the valve
to close.
The Figure 1206 Check Valve may be ordered from the factory either as flow horizontal or flow up. The cylinder
arrangement is available mounted on either side unless specified the Figure 1206 valve will be supplied with the
cylinder on the right side (when facing the inlet) and for horizontal flow.
The Figure 1206 has internal components identical to the Figure 1106 except that the hinge pin is made from heat
treated, type 431 stainless steel and is unique to the Figure 1206.
Kennedy Valve / Check Valves 15-15
KENFLEX RESILIENT HINGED CHECK VALVE FIG 506
SIZE A ØB C D ØE F G H I
(aprox) (nom.) (nom.)
4 4.88 4.00 13 1.00 7.50 8 0.75 0.31 9.0
6 6.38 6.00 16 1.06 9.50 8 0.88 0.34 9.0
8 7.63 8.00 19.5 1.19 11.75 8 0.88 0.34 13.5
10 9.06 10.00 24.5 1.25 14.25 12 1.00 0.38 16.0
12 10.63 12.00 27.5 1.28 17.00 12 1.00 0.41 19.0
L004
Kennedy Valve / Check Valves 15-17
FEATURES:
15-18
• Utilizes same components as the 106 Swing Check Valve
• 200 Working Pressure
• 400 Test Pressure
• Available in sizes:
4 x 6, 4 x 8, 6 x 8, 6 x 10, 8 x 10, 8 x 12, 10 x 12
• Resilient Seat (Rubber Disk, Bronze Seat) Ring
• Available in either Plain, Lever & Spring or Lever & Weight
SIZE A B C D E F G H I J K L M N
4X6 13.50 8.31 9 8.19 4 7.50 9 0.94 8-0.63 6 9.50 11 1 8-0.75
4X8 15 8.31 9 8.19 4 7.50 9 0.94 8-0.63 8 11.75 13.50 1.13 8-0.75
6X8 17 10.06 11 9 6 9.50 11 1 8-0.75 8 11.75 13.50 1.13 8-0.75
15-19
KENNEDY VALVE KS-FW
RESILIENT
WEDGE VALVES
KENNEDY
KENNEDY VALVE KS-FW
VALVE MODEL
Figure No.
Figure No. with
Available End Connections & Size Range (STD) Post Plate
Flg. End (NRS) 2" - 12" 8561ASS 8701ASS(3"-12")
M.J. 2" - 12" (except 2 1/2") 8571SS 8071SS(3"-12")
Flg. & M.J. 3" - 12" 8572SS 8702SS(3"-12")
Push-on for PVC (SDR) 2" - 8" 8597SS 8597PSS(3"-8")
Flg. End (OS & Y) 2 1/2" - 12" 8068A N/A
M.J. for Tapping 4" - 12" 8950SS 8950PSS
Push-on for D.I. & C900 PVC 4" - 12" 8901SS 8901PSS
M.J. Cutting-in 4" - 12" 8576SS 8576PSS
Push-on D.I. X Flg. 4" - 12" 8902SS 8902PSS
Threaded 2" - 3" 8057SS 8057PSS(3"only)
Threaded (OS&Y) 2" - 3" 8067SS N/A
Accessories
Indicator Posts Handwheels
“T” Handles Extension Stems
Stem Guides Floor Boxes
2" Sq. Operating Nuts Chain Wheels
Floorstands (non-rising stem) EPDM Wedges Available
VALVE
SIZE A B C D E F G H WEIGHT*
2 7 3 1/2 6 11/16 10 7/8 4 5/8 7 1/4 2 41
2 1/2 7 1/2 3 3/4 7 11/16 11 3/8 4 5/8 7 1/4 2 1/2 49
3 8 4 7 1/2 3/4 12 3/8 4 5/8 10 3 62
4 9 4 1/2 9 15/16 14 3/4 8 5/8 10 4 1/4 99
6 10 1/2 5 1/4 11 1 19 8 3/4 12 6 1/4 142
8 11 1/2 5 3/4 13 1/2 1 1/8 22 1/2 8 3/4 14 8 1/4 239
10 13 6 1/2 16 1 3/16 26 1/2 12 7/8 18 10 1/4 408
12 14 7 19 1 1/4 30 12 7/8 18 12 1/4 554
*ADD 16 LBS. FOR INDICATOR POST PLATE (3"-12" ONLY)
VALVE
SIZE A B C D E F G H WEIGHT
2 7 3 1/2 6 11/16 12 10 4 5/8 7 1/4 N/A
2 1/2 7 1/2 3 3/4 7 11/16 13 7/8 16 3/8 4 5/8 7 1/4 51
3 8 4 7 1/2 3/4 15 5/8 18 7/8 4 5/8 10 64
4 9 4 1/2 9 15/16 18 1/4 22 3/4 8 5/8 10 105
6 10 1/2 5 1/4 11 1 23 3/4 30 1/8 8 3/4 12 152
8 11 1/2 5 3/4 13 1/2 1 1/8 29 1/4 37 3/4 8 3/4 14 253
10 13 6 1/2 16 1 3/16 35 3/8 45 3/4 12 7/8 18 427
12 14 7 19 1 1/4 40 5/8 53 1/8 12 7/8 18 581
ALL FLANGE VALVES TAPPED & PLUGGED @ POSITION "A"
ELLIPTICAL
BOLT
HOLES
ELLIPTICAL BOLT HOLE DESIGN ELIMINATES THE NEED FOR ANTI-ROTATIONAL BOLTS
VALVE
SIZE A B C D E F G H WEIGHT*
2 8 1/4 4 1/8 2 1/2 4 1/2 10 7/8 2 5/8 7 1/4 2 36
2 1/2 —— —— —— —— —— —— —— —— ——
3 8 1/2 4 1/4 2 1/2 7 3/4 12 3/8 4 5/8 10 3 59
4 9 1/2 4 3/4 2 1/2 9 1/8 14 3/4 4 3/4 10 4 1/4 86
6 10 1/2 5 1/4 2 1/2 11 3/8 19 6 3/4 12 6 1/4 134
8 13 1/8 6 9/16 2 1/2 13 3/4 22 1/2 6 3/4 14 8 1/4 206
10 15 1/2 7 3/4 2 1/2 15 3/4 26 1/2 8 3/4 18 10 1/4 351
12 16 8 2 5/8 18 30 8 3/4 18 12 1/4 473
*ADD 16 LBS. FOR INDICATOR POST PLATE (3"–12" only)
ELLIPTICAL
BOLT
HOLES
ELLIPTICAL BOLT HOLE DESIGN ELIMINATES THE NEED FOR ANTI-ROTATIONAL BOLTS
VALVE
SIZE A B C D E F WEIGHT*
3 8 1/4 4 4 1/4 10 12 3/8 3 60
4 9 1/4 4 1/2 4 3/4 10 14 3/4 4 1/4 79
6 10 1/2 5 1/4 5 1/4 12 19 6 1/4 134
8 12 5/16 5 3/4 6 9/16 14 22 1/2 8 1/4 213
10 14 1/4 6 1/2 7 3/4 18 26 1/2 10 1/4 365
12 15 7 8 18 30 12 1/4 497
*ADD 16 LBS. FOR INDICATOR POST PLATE
VALVE
SIZE A B C D E F G WEIGHT*
4 13 1/4 6 5/8 4.34 14 3/4 10 8 3/16 3 3/4 82
6 14 3/4 7 3/8 4.75 19 12 10 7/8 3 3/4 139
8 17 1/8 8 9/16 5.70 22 1/2 14 12 7/8 4 1/2 216
10 19 3/8 9 11/16 6.19 26 1/2 18 15 15/16 5 1/8 359
12 20 7/8 10 7/16 6.19 30 18 17 7/16 5 3/8 501
VALVE
SIZE A B C D E F WEIGHT*
4 11 1/8 4 1/2 6 5/8 10 14 3/4 4 1/4 85
6 12 5/8 5 1/4 7 3/8 12 19 6 1/4 139
8 14 5/16 5 3/4 8 9/16 14 22 1/2 8 1/4 219
10 16 3/16 6 1/2 9 11/16 18 26 1/2 10 1/4 372
12 17 7/16 7 10 7/16 18 30 12 1/4 515
*ADD 16 LBS. FOR INDICATOR POST PLATE
VALVE
SIZE A B C D E WEIGHT*
2 10 5 3 1/2 10 7/8 7 1/4 35
2 1/2 10 3/4 5 3/8 3 3/4 11 3/8 7 1/4 44
3 11 5/8 5 13/16 4 1/6 12 3/8 10 53
4 13 1/2 6 3/4 4 1/2 14 3/4 10 84
6 15 3/4 7 7/8 5 3/8 19 12 137
8 16 1/4 8 1/8 5 3/8 22 1/2 14 223
ELLIPTICAL
BOLT
HOLES
ELLIPTICAL BOLT HOLE DESIGN ELIMINATES THE NEED FOR ANTI-ROTATIONAL BOLTS
VALVE
SIZE A B C D E F G H J WEIGHT*
4 9 1/2 4 3/4 2 1/2 9 1/8 14 3/4 4 3/4 10 5 .10 6.20 86
6 10 1/2 5 1/4 2 1/2 11 3/8 19 6 3/4 12 7 .20 8.30 134
8 13 1/8 6 9/16 2 1/2 13 3/4 22 1/2 6 3/4 14 9.40 10.50 206
10 15 1/2 7 3/4 2 1/2 15 3/4 26 1/2 8 3/4 18 11.50 12.62 351
12 16 8 2 5/8 18 30 8 3/4 18 13.60 14.72 473
ALVE
V
SIZE A B C D E WEIGHT*
ELLIPTICAL
BOLT
HOLES
ELLIPTICAL BOLT HOLE DESIGN ELIMINATES THE NEED FOR ANTI-ROTATIONAL BOLTS
VALVE
SIZE A B C D E F G WEIGHT*
4 9 1/4 4 1/2 4 3/4 10 14 3/4 3/16 4 1/4 92
6 10 1/2 5 1/4 5 1/4 12 19 1/4 6 1/4 144
8 13 1/4 5 3/4 7 1/2 14 22 1/2 1/4 8 1/4 224
10 14 1/4 6 1/2 7 3/4 18 26 1/2 1/4 10 1/4 392
12 15 7 8 18 30 1/4 12 1/4 527
*ADD 16 LBS. FOR INDICATOR POST PLATE
ALVE
V
SIZE A B D E F WEIGHT*
Available in Sizes B C D E
See Page 6 for Dimensions
1 1/4" sq.
36 3/4"
telescoping
30" Barrel
ground line
10"
Field Adjustment
Instructions
1. Remove the top section from the top of the
Indicator Post assembly.
5 1/8 "
trench 2. Loosen the telescoping barrel screws and
depth adjust barrel to the ground line.
Available in Sizes F G H
See Page 6 for Dimensions
P-2 P-1
P-3
P-4
P-5
P-6
P-7
P-8
P-9
P-10
P-23
P-11F
P-12
P-13 P-22
P-14
P-18
P-19
P-20
P-21
Available in Sizes F G H
See Page 6 for Dimensions
1 1/4" sq.
36 3/4" standpipe
(painted red)
30"
ground line
standpipe
(painted black)
Field Adjustment
Instructions
1. Remove the top section from the top of the
Indicator Post assembly.
5 1 /8 "
trench 2. Cut the required length off the bottom of the
depth Standpipe for the Ground Line to match up
with Standpipe Ground Line mark.
Valve
Size Min. Max. Min. Max. Min. Max. Min. Max.
Installation ‑ The valve should be opened to the fully open position before proceeding with the
• Loosen the two screws on the barrel and slide off the top of the standpipe.
• Attach the base flange along with the standpipe to the valve plate using the four 5/8" bolts
and nuts provided.
• Lower the barrel over the standpipe until the grade line mark on the barrel is at ground line
height and then tighten the two screws securely.
• Cut the required length off the bottom of the standpipe so that the indicated grade line of
the standpipe is at the ground line height and then secure to the base flange by tightening
the two screws.
Lower the stem into the barrel/standpipe, placing the crane coupling over the valve operating nut.
It is necessary that the stem engage the operating nut a minimum of 2 inches, but not more than
5 inches.
To check for correct engagement, the end of the stem should be from 7 inches to 10 inches above
the top of the standpipe (Fixed Length Units) or the top of the telescoping barrel.
Remove the target assembly from inside the body by rotating the operating nut counterclockwise.
5. Cont’d
Note: Position of the SHUT target can be determined by the following chart:
Valve
Size 4" 6" 8" 10" 12" 14"
Gate
Valve “A” 1" 1 3/ 8" 13/16" 23/16" 2 5/ 8" 3"
RW
Valve “A” 7 8 /" 15/16" 111/16" 2 1/ 8" 2 1/ 2" 2 7/ 8"
Position the SHUT target as indicated below and tighten the retainer screws until snug. Avoid over tightening.
Repeat the procedure for the other side.
adjustment of target:
4
5 19 16 1. grasp target at midpoint & pull
out slightly.
2. slide up or down to desired
location & then release grip.
The procedure is similar as for open left, but with two differences:
The position of the shut target above the open target is then determined and set as described above.
Maintenance
1. Lubrication
Oil upper bearing at least once per year, adding several drops of oil in the hole located on the top of the main
stem flange.
Access to lubrication hole is gained by raising the locking wrench off the main stem nut.
2. Operation
The target mechanism will travel off the threads of the operating nut in both directions should the targets or
target mechanism be positioned incorrectly. Should this happen, readjust targets. If the target mechanism falls
from the operating nut, it will be stopped a short distance below the window.
NOTE: Kennedy Valve does offer for sale Couplings to extend Stems
6 NO. DESCRIPTION
1
1 Ductile Pipe (as reqd)
2 2 Extender Coupling
1 3 Set Screw 3/4 UNCX1"lg
4
3 4 Lower
5 Extension Stem
6 Ext. Stem Coupling
8 7 Existing Stem
4 8 Cotter Pin
7
Fig. 551-Angle Wall Post Kit, use with 641-13 wall post (Style “A” includes 2 –
18" stems)
(Style “B” includes 2 – 24" stems)
Fig. 551
Angle
Wall
Post Kit
17-11
ANGLES ± .50 DEG.
FLANGED BASE POST INDICATOR
Kennedy Valve
The Kennedy Flanged Base Indicator Post, Figure 641-14, is specially designed to be mounted on a vault/
pit cover. This non-adjustable post can be supplied with couplings for non-rising stem valves.
PARTS LIST
NO. ITEM MATL ASTM
*1 WELDLESS EYE BOLT STL
—
*3 WASHER-PLATED STL A108
*4 HANDWHEEL-14" DIA CI A126B
5 COVER CI A126B
6 SNAP RINGS #5100-225
7 STEM NUT BR B-62
8 NUTS 1/2-UNC PLATED AP STL
9 BOLT 1/2-UNC X 2" AP STL A304B
10 BOLT 1/2-UNC X 1.75" AP STL A304B
11 TOP SECTION CI A126B
12 TARGET NUT BR B-62
13 WINDOWS PLAST
14 SCREWS-SELF TAP STL
15 FERRULE STL
16a TARGET PLATE (OPEN) ALUM
16b TARGET PLATE (SHUT) ALUM
17 CLAMPS-PLATED STL
18 NUTS-SQUARE STL
19 MACH SCREW-AD HEAD BR
20 PIPE PLUG-1/2 NPT CI
21 4 in. D.I. PIPE DI
22 4 in. FLOOR FLANGE CI A126B
23 STEM 87" STANDARD STL
24 WRENCH MI A47
25 CRANE COUPLING CI A126B
26 COTTER PIN BR B-16
*DENOTES OPTIONAL HANDWHEEL PARTS.