This document contains an examination for a steel structures course. It is divided into 5 units, each with 2 questions. The questions involve designing steel structural elements like beams, columns, and connections using principles of strength of materials. Students must choose 1 question from each unit and show all work in a single place. The document provides instructions, loads, dimensions, material properties and sketches as needed to solve the design problems.
This document contains an examination for a steel structures course. It is divided into 5 units, each with 2 questions. The questions involve designing steel structural elements like beams, columns, and connections using principles of strength of materials. Students must choose 1 question from each unit and show all work in a single place. The document provides instructions, loads, dimensions, material properties and sketches as needed to solve the design problems.
This document contains an examination for a steel structures course. It is divided into 5 units, each with 2 questions. The questions involve designing steel structural elements like beams, columns, and connections using principles of strength of materials. Students must choose 1 question from each unit and show all work in a single place. The document provides instructions, loads, dimensions, material properties and sketches as needed to solve the design problems.
This document contains an examination for a steel structures course. It is divided into 5 units, each with 2 questions. The questions involve designing steel structural elements like beams, columns, and connections using principles of strength of materials. Students must choose 1 question from each unit and show all work in a single place. The document provides instructions, loads, dimensions, material properties and sketches as needed to solve the design problems.
5. Determine the tensile strength of a single angle section [AURCE-604]
100mm*100mm*10mm connected to a 8mm thick gusset B. Architecture Degree Examination plate with four 20mm diameter rivets 10 VI SEMESTER OR STEEL STRUCTURES 6. Design the tension member consisting of a pair of angles (back (Effective from the admitted batch 2011–12) to back) and connected by the short legs to the same side of gusset Time: 3 Hours Max.Marks: 50 plate. The member is to carry a pull of 250 KN 10 ---------------------------------------------------------------------------------------------------- Instructions: Each Unit carries 10 marks. UNIT-IV Answer all units choosing one question from each unit. All parts of the unit must be answered in one place only. 7. Design the built up column of length 10m with two channel section Figures in the right hand margin indicate marks allotted. back to back and to carry an axial load of 1000KN. The column --------------------------------------------------------------------------------------------------- both ends are effectively held in position but not in direction 10 UNIT-I OR 1. What are the types of Rolled steel sections briefly explain purpose 8. Design a double angle discontinuous strut to carry 180 KN load. of each type 10 The length of structure between centre to centre of intersection OR is 4m 10 UNIT-V 2. A double cover butt joint is used to comet plates 16mm thick. Design the reverted joint and determine its efficiency. Use power 9. Define modulus of elasticity, sheer modulus of elasticity, Bulk driven rivets. Take FY=260H/mm2 10 modulus of elasticity and poisons ratio 10 UNIT-II OR 3. a) Explain the types of butt welded joints with neat sketches 7 10. An ISMB 325C431 is provided as a simply supported beam over b) What is effective throat thickness? 3 a span of 6m. Determine the imposed load that the beam can carry, if the permissible stress is bending is not to exceed 185/mm2 and the OR deflection is not to exceed L/325 10 4. Design suitable longitudinal fillet weld to connect the plates as shown in figure.1 and to transmit a pull equal to the full strength of thin plate. Allowable stress in the weld is 110N/mm2 and tensile [65/VI S/115] stress in plate 0.6 fyN/mm2. The plates are 10mm thick 10 UNIT-III [April-15] 5. Determine the tensile strength of a single angle section [AURCE-604] 100mm*100mm*10mm connected to a 8mm thick gusset B. Architecture Degree Examination plate with four 20mm diameter rivets 10 VI SEMESTER OR STEEL STRUCTURES 6. Design the tension member consisting of a pair of angles (back (Effective from the admitted batch 2011–12) to back) and connected by the short legs to the same side of gusset Time: 3 Hours Max.Marks: 50 plate. The member is to carry a pull of 250 KN 10 ---------------------------------------------------------------------------------------------------- Instructions: Each Unit carries 10 marks. UNIT-IV Answer all units choosing one question from each unit. All parts of the unit must be answered in one place only. 7. Design the built up column of length 10m with two channel section Figures in the right hand margin indicate marks allotted. back to back and to carry an axial load of 1000KN. The column --------------------------------------------------------------------------------------------------- both ends are effectively held in position but not in direction 10 UNIT-I OR 1. What are the types of Rolled steel sections briefly explain purpose 8. Design a double angle discontinuous strut to carry 180 KN load. of each type 10 The length of structure between centre to centre of intersection OR is 4m 10 UNIT-V 2. A double cover butt joint is used to comet plates 16mm thick. Design the reverted joint and determine its efficiency. Use power 9. Define modulus of elasticity, sheer modulus of elasticity, Bulk driven rivets. Take FY=260H/mm2 10 modulus of elasticity and poisons ratio 10 UNIT-II OR 3. a) Explain the types of butt welded joints with neat sketches 7 10. An ISMB 325C431 is provided as a simply supported beam over b) What is effective throat thickness? 3 a span of 6m. Determine the imposed load that the beam can carry, if the permissible stress is bending is not to exceed 185/mm2 and the OR deflection is not to exceed L/325 10 4. Design suitable longitudinal fillet weld to connect the plates as shown in figure.1 and to transmit a pull equal to the full strength of thin plate. Allowable stress in the weld is 110N/mm2 and tensile [65/VI S/115] stress in plate 0.6 fyN/mm2. The plates are 10mm thick 10