Professional Documents
Culture Documents
Unit 4 Solar Power Prof
Unit 4 Solar Power Prof
SOLAR POWER
A solar cell, or photovoltaic cell, is an electrical device that converts the energy
of light directly into electricity by the photovoltaic effect, which is a physical and
chemical phenomenon. Although there are other types of solar cells and continuing
research promises new developments in the future, the crystalline silicon solar cell
is by far the most widely used. A silicon solar cell consists of a thin layer or wafer of
silicon that has been doped to create a pn junction. The depth and distribution of
impurity atoms can be controlled very precisely during the doping process. The
silicon wafer is doped so that the n region is much thinner than the p region to
permit light penetration, as shown in Figure 1(a).
A grid-work of very thin conductive contact strips are deposited on top of the
wafer by methods such as photoresist or silk-screen, as shown in Figure 1(a). The
contact grid must maximize the surface area of the silicon wafer that be exposed to
the sunlight in order to collect as much light energy as possible. The conductive grid
across the top of the cell is necessary so that the electrons have a shorter distance to
travel through the silicon when an external load is connected. The farther electrons
travel through the silicon material, the greater the energy loss due to resistance. A
solid contact covering all of the bottom of the wafer is then added, as indicated in
the figure. Thickness of the solar cell compared to the surface area is greatly
exaggerated for purposes of illustration.
(a) (b)
Bài giảng dựa trên giáo trình “Tiếng Anh Chuyên Ngành Điện Tử- Viễn Thông” của
nhà xuất bản thông tin và truyền thông.
is sufficient solar energy striking the earth each hour to meet worldwide demands
for an entire year.
The n-type layer is very thin compared to the p region to allow light
penetration into the p region. The thickness of the entire cell is actually about the
thickness of an eggshell. When a photon penetrates either the n region or the p-type
region and strikes a silicon atom near the pn junction with sufficient energy to
knock an electron out of the valence band, the electron becomes a free electron and
leaves a hole in the valence band, creating an electron-hole pair. The amount of
energy required to free an electron from the valence band of a silicon atom is called
the band-gap energy and is 1.12 eV (electron volts). In the p region, the free electron
is swept across the depletion region by the electric field into the n region. In the n
region, the hole is swept across the depletion region by the electric field into the p
region. Electrons accumulate in the n region, creating a negative charge; and holes
accumulate in the p region, creating a positive charge. A voltage is developed
between the n region and p region contacts, as shown in Figure 1(b).
When a load is connected to a solar cell via the top and bottom contacts, the
free electrons flow out of the n region to the grid contacts on the top surface,
through the negative contact, through the load and back into the positive contact on
the bottom surface, and into the p region where they can recombine with holes. The
sunlight energy continues to create new electron-hole pairs and the process goes on,
as illustrated in Figure 1(b).
Cell (n) Tế bà o
Crystalline (adj) Thuộ c về tinh thể
Consist (v) Bao gồ m
Junction (n) Tiếp giá p
Dope (v) Pha tạ p
Penetration (n) Sự xuyên qua
Conductive (adj) Dẫ n điện
Deposit (v) Đặ t để
Load (n) Tả i
Absorb (v) Hấ p thụ
Valence band (n) Vù ng hó a trị
Conduction band (n) Vù ng dẫ n
Band-gap (n) Vù ng cấ m
Depletion (n) Sự thiếu hụ t
Accumulate (v) Tích trữ
Develop (v) Phá t triển
Recombine (v) Tá i hợ p
Bài giảng dựa trên giáo trình “Tiếng Anh Chuyên Ngành Điện Tử- Viễn Thông” của
nhà xuất bản thông tin và truyền thông.
Tế bào NL mặt trời hay còn gọi là tế bào quang điện là một thiết bị điện chuyển đổi
năng lượng ánh sáng trực tiếp thành điện năng nhờ hiệu ứng quang điện
t, đó là một hiện tượng vật lý và hóa học. Mặc dù có nhiều loại pin mặt trời khác và
việc tiếp tục nghiên cứu hứa hẹn những phát triển mới trong tương lai, nhưng pin mặt
trời silicon tinh thể cho đến nay vẫn được sử dụng rộng rãi nhất. Một pin mặt trời
silicon bao gồm một lớp mỏng hoặc wafer silicon đã được pha tạp để tạo ra một điểm
nối pn. Độ sâu và sự phân bố của các nguyên tử tạp chất có thể được kiểm soát rất
chính xác trong quá trình pha tạp. Tấm wafer silicon được pha tạp sao cho vùng n
mỏng hơn nhiều so với vùng p để cho phép ánh sáng xuyên qua, như trong Hình 1
(a).
Một lưới điện gồm các dải tiếp xúc dẫn điện rất mỏng được đặt trên đỉnh của wafer
bằng các phương pháp như quang dẫn hoặc màn hình lụa, như trong Hình 1 (a). Lưới
tiếp xúc phải tối đa hóa diện tích bề mặt của wafer silicon tiếp xúc với ánh sáng mặt
trời để thu được càng nhiều năng lượng ánh sáng càng tốt. Lưới dẫn điện trên đỉnh
của tế bào là cần thiết để các electron có khoảng cách ngắn hơn để di chuyển qua
silicon khi tải bên ngoài được kết nối. Các electron càng đi xa qua vật liệu silicon, tổn
thất năng lượng càng lớn do điện trở. Một tiếp điểm chắc chắn bao gồm tất cả các
đáy của wafer sau đó được thêm vào, như được chỉ ra trong hình. Độ dày của pin mặt
trời so với diện tích bề mặt được phóng đại rất nhiều cho mục đích minh họa.
Sau khi các tiếp xúc được kết hợp, một lớp phủ chống phản xạ được đặt trên đỉnh của
lưới tiếp xúc và vùng n. Điều này cho phép pin mặt trời hấp thụ càng nhiều năng
lượng mặt trời càng tốt bằng cách giảm lượng năng lượng ánh sáng phản xạ ra khỏi
bề mặt tế bào. Cuối cùng, một lớp thủy tinh hoặc nhựa trong suốt được gắn vào đầu
tế bào bằng chất kết dính trong suốt để bảo vệ nó khỏi thời tiết.
Ánh sáng mặt trời được cấu tạo từ các photon, hoặc các gói năng lượng. Mặt trời tạo
ra một lượng năng lượng đáng kinh ngạc. Một phần nhỏ của tổng năng lượng mặt trời
đến trái đất là đủ để đáp ứng tất cả nhu cầu năng lượng của chúng ta nhiều lần. có
đủ năng lượng mặt trời chiếu sáng trái đất mỗi giờ để đáp ứng nhu cầu trên toàn thế
giới trong cả năm.
Lớp loại n rất mỏng so với vùng p để cho phép ánh sáng xuyên qua vùng p. Độ dày
của toàn bộ tế bào thực sự là về độ dày của vỏ trứng. Khi một photon xuyên qua
vùng n hoặc vùng loại p và tấn công một nguyên tử silicon gần tiếp giáp pn với năng
lượng đủ để đánh bật một electron ra khỏi dải hóa trị, electron sẽ trở thành một
electron tự do và để lại một lỗ trống trong dải hóa trị , tạo ra một cặp lỗ electron.
Lượng năng lượng cần thiết để giải phóng một electron khỏi dải hóa trị của nguyên tử
silicon được gọi là năng lượng khoảng cách dải và là 1,12 eV (vôn electron). Trong
vùng p, electron tự do bị quét qua vùng cạn kiệt bởi điện trường vào vùng n. Ở vùng
n, lỗ trống được quét qua vùng cạn kiệt bởi điện trường vào vùng p. Electron tích lũy
trong vùng n, tạo ra điện tích âm; và các lỗ tích lũy trong vùng p, tạo ra một điện tích
dương. Một điện áp được phát triển giữa các tiếp điểm vùng n và p, như trong Hình 1
(b).
Khi một tải được kết nối với pin mặt trời thông qua các tiếp điểm trên và dưới, các
electron tự do chảy ra khỏi vùng n đến các tiếp điểm lưới trên bề mặt trên, qua tiếp
điểm âm, qua tải và trở lại tiếp điểm dương trên bề mặt đáy, và vào khu vực p nơi
chúng có thể kết hợp lại với các lỗ. Năng lượng ánh sáng mặt trời tiếp tục tạo ra các
cặp lỗ electron mới và quá trình này tiếp tục, như được minh họa trong Hình 1 (b).
Bài giảng dựa trên giáo trình “Tiếng Anh Chuyên Ngành Điện Tử- Viễn Thông” của
nhà xuất bản thông tin và truyền thông.
1. Main idea
Which statement best expresses the main idea of the text? Why did you omit
the other choice?
1. The key feature of a solar cell is the pn junction.
2. The photovoltaic effect is the basic physical process by which a solar cell
converts sunlight into electricity.
3. A silicon solar cell consists of a thin layer or wafer of silicon that has been
doped to create a pn junction.
2. Questions
Bài giảng dựa trên giáo trình “Tiếng Anh Chuyên Ngành Điện Tử- Viễn Thông” của
nhà xuất bản thông tin và truyền thông.
Decide whether the following statements are true or false (T/F) by referring
to the information in the text. Then make the necessary changes so that the false
statements become true.
1. …T The conductive grid is necessary to reduce the energy loss due to
(para2) the resistance of the silicon material.
…
2. …T A band-gap energy is the amount of energy required to create an
(para5) electron-hole pair.
…
3. …F… The key feature of a solar cell is the antireflective coating.
4. …F The conductive grid must be maximized in order to collect as much
(para2) light energy as possible.
…
5. …F The energy loss of electrons is inversely proportional to the
(para2) distance they travel.
…
4. Understanding words
Refer back to the text and find synonyms for the following words
1. pollutant (para 1) ………impurity………………..
2. put (para 2) ………deposit………………..
3. uncover (para 2) ………expose………………..
4. take in (para 3) ………absorb………………..
5. reduction (para 5) …………depletion……………..
Refer back to the text and find antonyms for the following words
6. gain (para 2) …………loss……………..
7. increase (para 3) …………reduce……………..
8. opaque (para 3) …………transparent……………..
9. inadequate (para 5) …………sufficient……………..
10. dissipate (para 5) …………accumulate……………..
5. Content review
2. A solar system is typically designed taking into account the annual of average
peak sun per day for a given geographical area.
………………………………………………………………………………………………………………….
………………………………………………………………………………………………………………….
………………………………………………………………………………………………………………….
8. Discussion
Talking about solar power
Basic construction of a solar cell
Basic operation of a solar cell
Applications of solar cells
Bài giảng dựa trên giáo trình “Tiếng Anh Chuyên Ngành Điện Tử- Viễn Thông” của
nhà xuất bản thông tin và truyền thông.