Professional Documents
Culture Documents
User's Manual 9031-249Y: Aplr5L1, Aplu5L1
User's Manual 9031-249Y: Aplr5L1, Aplu5L1
User's Manual 9031-249Y: Aplr5L1, Aplu5L1
TOURING
User’s Manual
TS 30
9031-249Y
APLR5L1, APLU5L1
Dear User,
TEMSA Family
00 Content
9.1.1 Front Kneeling........................................................................ 145 13. Maintenance............................................................................ 175
9.1.2 Lifting..................................................................................... 146 13.1 Checking Engine Oil Level...................................................... 176
13.2 Checking Condition of Engine Oil.......................................... 176
10. Tires........................................................................................... 149 13.3 Checking Condition of Transmission Oil................................. 177
10.1 Tires......................................................................................... 150 13.4 Air Filter Maintenance............................................................. 178
10.2 Tire Pressure............................................................................ 150 13.5 Replacing Air Filter.................................................................. 180
10.3 Checking Tire Pressure............................................................ 151 13.6 Fuel Filter Maintenance........................................................... 180
10.4 Snow Tires............................................................................... 151 13.7 Expansion Tank Maintenance.................................................. 180
10.5 Snow Chains............................................................................ 152 13.8 Addition of Distilled Water...................................................... 181
10.6 Changing Tires........................................................................ 152 13.9 Usage of Antifreeze................................................................. 182
10.7 Shifting Tires............................................................................ 156 13.10 Radiator Maintenance.......................................................... 182
13.11 Air Conditioner Maintenance............................................... 183
11. Brakes....................................................................................... 159 13.12 Cleaning the Filters............................................................... 183
11. Brakes........................................................................................ 160 13.13 Checking the Drive Belt Tension.......................................... 184
11.1 ABS .......................................................................................... 160 13.14 Cleaning Vehicle Exterior...................................................... 184
11.2 Parking Brake........................................................................... 161 13.15 Cleaning Vehicle Interior...................................................... 185
11.3 Retarder................................................................................... 163 13.16 Lavatory Waste Tank Maintenance....................................... 186
11.4 ASR (Acceleration Slip Regulation).......................................... 164 13.17 Corrosion Protection............................................................. 186
11.5 Intarder.................................................................................... 164
11.6 Engine Brake............................................................................ 165 14. INDEX........................................................................................ 191
This User`s Manual is prepared to Please contact authorized TEMSA The vehicle is designed for trans-
use your vehicle in the safest and Service if you have difficulty in portation of passengers and their
the most efficient way. understanding explanations in the luggage only.
user’s manual.
Safety instructions given in this Passenger capacity according to
User’s Manuals are intended to pro- In addition to the information pro- seat arrangement is indicated in the
tect persons and properties. vided within this manual, all pre- passenger capacity label and regis-
Information
maintenance work, read this man- This manual is intended to be used for its design purpose.
ual completely and carefully. commonly for all variants of TS 30,
therefore some properties of your The owner of the vehicle will be
Any injury or damage arisen from vehicle may not comply with those held liable for any other use beyond
non-compliance with the safety in- indicated in this manual. this design purpose.
structions given in this manual is the
responsibility of the vehicle’s owner. Also illustrations used in this manual
are intended to be shown proce-
Should the vehicle be sold, the dures, usage and other important
User’s Manual must be delivered to subjects for the user. Therefore they
the new owner of the vehicle. may have some differences than the
Warning original views.
It is assumed that all the informa-
Technical information and
tion and safety instructions given
properties of the vehicles stat-
in this manual, can be understood
ed within this User’s Manual
clearly by the owner and the user
are valid on the date of issue.
of the vehicle who have sufficient
TEMSA, reserves the right to
occupational experience and knowl-
make any necessary changes
edge.
to the features of its products
without giving any advance
notice.
Before driving, take all necessary To contact NHTSA, you may either Fuel Quality Production
safety and environmental aspects call the Auto Safety Hotline toll-free The tank must not be filled with Whether in production or repair,
into consideration. Ensure that the at 1-(800)-424-9393 (or 366-0123 more than 95 % of tank volume. TEMSA Global always relies on en-
vehicle is in technically perfect con- in Washington, D.C. area) or write The legal capacity is displayed on vironmentally friendly technology.
dition. to: NHTSA, U.S. Department of the fuel filler door outside. Use only A waste-management system has
Transportation, Washington, D.C. ultra low sulfur diesel (ULSD). been introduced to reduce the
If you believe that your vehicle has 20590. You can also obtain other amount of waste while simultane-
Information
a fault which could cause a crash, information about motor vehicle California Proposition 65 ously increasing the recycling rate.
injury or death, you should imme- safety from the Hotline. Warning NOTICE! Waste water leaves the TEMSA
diately inform the National Highway
01 General
Engine exhaust, some of its con- Global factory only after being ap-
Traffic Safety Administration (NHT- Observe all safety instructions and stituents, and certain vehicle com- propriately treated.
SA) in addition to notifying TEMSA warnings displayed on the vehicle. ponents contain or emit chemicals
Global. The vehicle owner must ensure the known to the State of California for Any fault messages are indicated to
presence and legibility of all warn- causing cancer and birth defects the driver by the ”Check Engine“
If NHTSA receives similar com- ings and information signs through- or other reproductive harm. In ad- warning light and the on-board
plaints, it may open an investi- out the vehicle’s service life. dition, certain fluids contained in computer.
gation, and if it discovers that a vehicles and certain wear compo-
safety problem exists in a group of Any alteration of the vehicle may nents contain or emit chemicals
vehicles, it may order a recall and interfere with safety features built known to the State of California for
remedy campaign. However, NHTSA into the vehicle and may lead to an causing cancer and birth defects or
cannot become involved in individ- accident resulting in serious injury other reproductive harm.
ual problems between you and your or death.
dealer, or TEMSA Global.
Throughout this booklet, left is de-
fined as the driver’s side of the ve-
hicle, and right as the passenger’s
side of the vehicle.
• Parts of clothing can be- from the traffic and cause monoxide (CO), which is a
great extent on the individual driv-
come damaged. you losing control of the colourless and odorless gas.
ing style and the conditions of use
vehicle resulting in serious Carbon monoxide can cause
and therefore cannot be expressed
For more information refer to personal injury or death. unconsciousness and even
in actual miles on the road. The
Section 7 (Engine). • Operate the components death if inhaled.
values communicated by TEMSA
while driving only if the traf- • Never start or let the engine
Global are based on normal opera-
fic situation allows you to do run in an enclosed, unventi-
tion adapted to traffic.
so safely. lated area.
• Carry out any complicated • It is not recommended to
operating or setting proce- sit in your vehicle for pro-
dures only while the vehicle longed periods with the
is stationary. engine on and the vehicle
• Take prevailing national reg- not moving.
ulations into consideration.
Information
immediately inform the National It is the responsibility of the bus Check the service brake adjust-
Highway Traffic Safety Administra- Owner / Operator to ensure com- ment.
tion (NHTSA) describing the prob- pliance with all federal, state and Check the park brake adjustment on
01 General
lem. You should also notify TEMSA local regulations for school bus op- units equipped with hydraulic brake
Global immediately so that they can eration and equipment. As part of a systems.
evaluate the situation or condition. daily pre-trip inspection, the Driver Check the torque on all body “tie-
should consider it his/her respon- down” bolts.
If NHTSA receives more informa- sibility to verify that the vehicle is Check the engine oil level.
tion of similarnature, it may open in satisfactory working order and Check the transmission fluid level.
an investigation regarding this mat- that all emergency equipment is Check the engine coolant level.
ter. If NHTSA determines there is a in place, fully stocked (First Aid Kit), Check the air pressure in all tires.
common safety defect in a group up-to-date (Fire Extinguisher), and in Check the torque on the driveline
of buses, it may issue an orderfor proper working condition. universal joint straps.
a recall. NHTSA will not, however,
become involved in an individual is- Inspection guidelines from individ-
sue between the owner/operator, ual state inspection manuals (such
distributor and/or TEMSA Global. as Commercial Driver’s License pre-
trip inspection procedures) take
To contact NHTSA, call the precedence over those found in this
Auto Safety Hotline toll free at manual. Guidelines found herein are
1.800.424.9393 (outside the in addition to those in your state’s
Washington, DC area). In the Wash- inspection requirements.
ington, DC area, call 366.0123.
The NHTSA may also be contacted
in writing to the following address:
Mobile phones and radio commu- For a safer and longer service life of Carry out all maintenance and ser-
nication devices may distract the the vehicle, use only TEMSA genu- vice work completely and within
driver during driving. Therefore it ine spare parts, accessories or parts the specified intervals as described
is recommended not to use such which have been approved and in this manual and in the warranty
devices. tested by TEMSA. and service documentation.
Information
Furthermore, usage of mobile All genuine parts have been ap- The service and maintenance op-
phones or other devices transmit- proved by TEMSA by means of erations should be carried out by
ting electromagnetic waves must testing their reliability, endurance authorized services and be in com-
01 General
comply with prevailing national and safety factors. TEMSA does not pliance with TEMSA directives.
regulations. take any responsibility for any injury
or damage due to use of non-ap- You should keep a record with all
Before adding sound equipment, proved third party products. parts receipts and list the mileage
check with your dealer and be sure and the date of any service work
to check Federal rules covering mo- Any alteration of the vehicle may you perform and/or authorized
bile radio and telephone units. interfere with safety features built service performed.
into the vehicle and may lead to an
accident resulting in serious injury Incomplete or improper servicing
or death. may causeproblems in the op-
eration of the vehicle. If you are
in doubt about any servicing, have
it done by your authorized TEMSA
Global dealer. Improper mainte-
nance during the warranty period
will jeopardize your TEMSA Global
warranty coverage.
Information
5 Take a Break from Idle Time Use the cruise and slow down
Optimum lubrication and tuning Limit the warm up time; Excessive • Electronic cruise control saves
result in a 3 % to 5 % improvement idling wastes fuel, adds contami- fuel, makes driving easier.
01 General
in fuel economy. nants to the oil, and adds carbons • Think twice about the cruise
to the combustion chamber. speed you choose.
2 Engine • Every mile per hour over 55 adds
Idling engines use about 0.39 gal almost 0.66 gal/ 2.5 liters more
Optimum fuel economy is reached /1.5 liters of diesel per hour. Engine consumption per 62.1 miles.
at max. tractive force range of your idling shutdown pays off in prevent- • Remember, torque moves the
engine. ing unnecessary fuel consumption load
of stationary vehicles. • Torque moves the load; horse-
3 Axle Alignment power determines how fast it
6 Gearbox (Manual Operation) moves.
Incorrect axle alignment can impact • Staying in the preferred torque
consumption by up to 3 %. Practice progressive shifting. You range keeps the engine operat-
do not have to, but overtaking the ing more efficiently and puts
4 Tire Pressure shifting is always possible: more profit in your pocket.
It is well known that a low tire pres- Change gears earlier (even lower
sure increases fuel consumption by engine speeds) Shift up as soon as
up to 5 %. If the tire pressure is 20 % you have enough rpm to grab the
below the correct pressure, the roll- Cutting idle time from 50 % to 25 % next higher gear.
ing resistance will be about 10 % can improve fuel economy by up Hold the gear (driver’s assessment)
higher and the fuel consumption to 4%. No need to increase revs!
will be about 5 % higher.
you are pulling a long gradient, be a lot of energy when it moves) range is the same as the highest
patient. limit of this range, resulting in high Do I really need to accelerate that
When throttle is released your con- driving comfort at low revs. much in this situation?
Letting the engine rpm pull back on sumption is ZERO. 0.6 mph (1 km/h) faster = 1 % high-
gradients will not hurt your engine. er fuel consumption: Use the vehicle speed.
Do not build up too much speed • Driving at 85 instead of 80: +5 %
9 Use the Energy and then correct it. • Driving at 90 instead of 85: +5 % Weight of your vehicle represents
a lot of energy when it move, use
Let the mass work for you and make The Whole Makes the Difference that energy.
the most of momentum.
Save the
An efficient driveline alone does not
Environment Summary
Lowering the fuel
When no throttle is given, drive in guarantee the best return on fuel in
consumption will reduce the
the highest gear (low internal resis- everyday use. It is the total of dif- Anticipate:
exhaust emissions and will pro-
tance). Look further ahead; avoid ferent factors, like the overall con- • Release throttle in good time.
tect the environment.
unnecessary braking; drive consis- figuration of the vehicle, the main- • Prevent unnecessary braking.
tently. tenance condition and the driving • Drive no faster than is necessary
style that are decisive for the fuel Additional energy consumers have at a given time.
Let momentum of your vehicle work efficiency. an impact as well:
for you to save fuel. • Air conditioning: 2 %
In general less weight means more • Extra Lights on: 1 % - 3 %
Coasting in gear allows all the fuel payload or less fuel. If aluminum
to return to the tank. wheels are fitted, the gain also in-
Information
This symbol indicates that nance work.
mentioned property of the
01 General
vehicle is optional. (Model
specifications, models speci-
fied to the country, optional
Aural Rotating Parts
Inspection Consult
equipment). This symbol is used to indicate
This symbol is used Authorized
conditions where the user may
to inform the user that the TEMSA Service
be hit and injured by rotating
complementary soundcan be This symbol is used in condi-
parts.
heard after carrying out the tions where authorized TEMSA
mentioned instruction. Service should be consulted
Information
for described maintenance,
This symbol is used when im-
Do it yourself repair and inspection work.
portant additional information
is given. This symbol indicates that
mentioned instruction can be
Hot Surfaces carried out by the user.
This symbol is used to indicate
Visual the risk of burns in case of con-
Save the
Inspection tact with hot surfaces.
Environment
This symbol is used to Document This symbol is used
inform the user that the com- Reference to indicate the environment
plementary indicator lamp See also other manu- should be considered when
would be lit after carrying out als delivered for information. conducting this task.
the mentioned instruction.
CAUTION
TURN THE TURNING
KNOB TO OPEN THE
DOOR IN ANY
EMERGENCY CASE
11’8”
3,60 m
LIFTED HEIGHT
Information
01 General
NO STANDEE
TO OPEN
1-PUSH THE LID UP.
SUITABLE TIRE-RIM CHOICE: 2-PULL THE WHITE KNOB.
FRONT: TIRES, 3-PUSH THE LID OUT.
RIMS,@ KPa( PSI).
COLD KPa TO CLOSE
1-PLACE THE LID BACK INTO THE SLOT.
REAR : TIRES, 2-PULL THE WHITE KNOB TO LATCH.
RIMS,@ KPa( PSI). 3-THEN PULL DOWN THE LID TO CLOSE. NO SMOKING
COLD KPa
1
3
EMERGENCY EXIT
CAUTION
WARNING USE CROSS VIEW MIRRORS TO VIEW
THIS VEHICLE IS EQUIPPED PEDESTRIANS WHILE BUS IS STOPPED.
DO NOT USE THESE MIRRORS TO VIEW
WITH A BACK-UP ALARM TRAFFIC WHILE BUS IS MOVING. IMAGES
ALARM MUST SOUND IN SUCH MIRRORS DO NOT ACCURATELY
SHOW ANOTHER VEHICLE’S LOCATION
FOR PASSANGERS SAFETY
WHEN BACKING, OPERATOR
MUST MAKE CERTAIN ALARM
(REF. FMVSS. 111)
FEDERAL LAW PROHIBITS
OPERATION OF THIS BUS WHILE
Information
IS WORKING BEFORE
OPERATING THIS VEHICLE
ANYONE IS STANDING FORWARD
01 General
OF THE WHITE LINE
PRESS BRAKE PEDAL BEFORE
SHIFTING INTO INITIAL GEAR
WARNING
DO NOT OPERATE THE BUS
WITH AN AIR PRESSURE
BELOW 100 PSI
ATTENTION
THIS VEHICLE IS FITTED WITH AN
ADVANCED HVAC SYSTEM. WARNING
TO ENSURE MAXIMUM PASSENGER
COMFORT KEEP DOOR CLOSED
DO NOT WORK IN THIS ENGINE
COMPARTMENT WHILE ENGINE IS
RUNNING.BE SURE STOPPING THE
ENGINE BEFORE WORKING IN THIS AREA.
Fasten Seatbelt
Abroche su cinturon
de seguridad
RIDE SAFELY
STAY SEATED WITH
KNEELING BUS SEATBELT FASTENED
O
DO NOT
L L A N T
SET THE COVER TO A SUITABLE
O L
OPEN CAP
POSITION TO AVOID ANY
Information
POTENTIAL DAMAGE AS THE WHEN
N T
DRIVER GLASS IS OPERATED ENGINE IS
HOT
THE TANK CANNOT BE
01 General
F
FILLED WITH A QUANTITY
O I
C L L
DAMAGE TO TRANSMISSION
OPERATION TOUCH
01 General
WARNING
GND -
MOVING SHAFT
24V + EXTREMELY
DANGEROUS
BP
TEMSA GLOBAL SAN VE TIC. A.Ş
% 55 -40 F
IMPORTANT
SERVICE INFORMATION
USE REFRIGERANT
Information
R-134a ONLY
The System Contains R-134a Refrigerant
01 General
SERVICE BY CERTIFIED TECHNICIAN ONLY
Stations only.
SPARE TIRE
DOWN
Information
UP
L HANDLE R
01 General
risk of fıre,
explosıon &
asphyxıatıon
Information
• At filling stations and other refu-
eling points.
01 General
• If the heater or its exhaust outlet
is in locations where inflammable
vapors or dust may form (e.g.
close to fuel, coal, wood dust or
cereal storage facilities).
• If the heater or its exhaust outlet
is located close to inflammable
materials for example dry grass
and leaves, cartons, paper etc.
• In enclosed areas (e.g. garages,
hall without a suck off facility),
not even if the digital timer or
Tele Start is used.
• If the exhaust outlet of the heater
is partial or fully obstructed (e.g.
by soil or snow, as it may occur
while move the vehicle back-
wards).
Information
Information
TECHNICALLY PERMISSIBLE
MAXIMUM WEIGHT :
Information
Fuel Tank Number of Cylinders 6 in line
79,25 gal Rims 7.5x19.5 inch
Maximum Power (Hp) 250
02 Vehicle
36 lt / Maximum Torque
Urea Tank 660/1600
9.5 gal Tires and Rims (lb-ft/rpm)
Dimensions
30.64 ft /
10,89 ft /
3319 mm
Length
9340 mm
94,64 inch /
Width
2404 mm
Information
10,89 ft /
Heigth
02 Vehicle
3319 mm
181 inch /
Wheelbase
4600 mm
77,95 inch /
Front Track Width
1980 mm 94,64 inch /
77,39 inch / 2404 mm
Rear Track Width
1915 mm
74,8 inch /
Front Extension
1900 mm
112 inch /
Rear Extension
2840 mm
30,64 ft / 9340 mm
Information
2.3.4 Lateral Control Panel
02 Vehicle
2.3.4 Lateral auto
auto auto
Control Panel
2.3.5 Right
Control Panel
mechanism.
ing flashers start flashing and aisle
Information
Information
Closing the red cover cap
pushes the switch forward and
holds it in position.
Kneeling Lifting Engine Brake On/ Engine Brake Level Blind Left Switch
Control Switch Off Switch Switch (Optional)
Press lower side of Press upper side of Switch has three lev- Press upper side of
KNEELING &
LIFT CONTROL
the switch to per- ENGINE BRAKE
ON/OFF
the switch to acti- ENGINE BRAKE
LEVEL
els. Press button to BLIND
LEFT
the switch to move
form kneeling func- vate “Engine Brake adjust engine brake the sun visor up-
tion. Level” switch. level. wards. Press lower
side of the switch to
Information
move it downwards.
02 Vehicle
Information Information Information (Optional)
• Front body height decreases To activate engine brake level 1st Position: Provides maxi- Press upper side of
as long as the lower side of switch, first press upper side of mum engine brake power. BLIND
RIGHT
the switch to move
the switch is pressed. the engine brake switch. 2nd Position: Provides less the sun visor up-
• Press upper side of the than 1st position engine brake wards. Press lower
switch to increase front power. side of the switch to
body height. 3rd Position: Provides mini- move it downwards.
Dimmer Switch mum engine brake power.
Press upper side of
DIMMER
the switch to in-
crease illumination Warning
of instrument panel. Using passenger side sun visor
Intarder (Optional)
limits the driver’s view on the
Enables the control
right rear view mirror. It may
of auxiliary brake
cause accidents.
unit (retarder) via
foot pedal.
Information
To illuminate instrument pan-
el, parking light switch must
be activated.
Deactivating
Information
Press lower side of cruise control Temperature Up
Information switch to deactivate. Button
• Press upper side of “cruise Press button to in-
02 Vehicle
control switch” to acti- crease temperature
vate “cruise control level setpoint.
switch”. Information
• Cruise control can be acti- Cruise control is deactivated Information
vated within speed range of when service brake is applied Refer to user’s manual Fan Speed Button
20 mph and 75 mph. or engine brake is activated. of air conditioner con- Press button to
• Move your foot from the
trol panel delivered adjust current fan
accelerator pedal before
with the vehicle for more in- speed.
pressing cruise control
formation.
switch. Cruise Control
Adjust Switch
CC
Increases or decreas- Fresh Air Selection
ADJUST On/Off Button
es set speed value. Button
Press button to turn
Press button to se-
on/off the air condi-
lect fresh air / recir-
tioner unit.
culated air mode.
Mode Select
Button
Press button to se-
lect A/C, heat or
ventilation mode.
Information
02 Vehicle
1 Speedometer 5 Warning Panel
2 Odometer 6 Temperature Indicator
3 Menu Selection Buttons 7 Revolution Counter
4 Fuel Indicator 8 Main Warning Panel
Displays current speed of the vehicle. Indicates engine speed in thousands Indicates current fuel level.
of revolutions per minute (rpm). Visual
Revolution counter guides you to Inspection 0 : Empty level
drive optimally. Warning lamp on the 1/1: Full level
tachometer lights up when
2300 rpm value is exceeded.
Visual Visual
Inspection Inspection
Check revolution Check fuel level regu-
counter regularly during driv- larly during driving.
ing. Avoid exceeding revolu-
tion value of 2300 rpm.
Information
tioner, activate
the parking brake Check the condition of V-belt is not
Indicates engine coolant tempera- and do not press the accelerator loose or damaged. Consult autho-
02 Vehicle
ture. Exceeding 100 °C/212 °F pedal until the engine coolant tem- rized TEMSA Service if any damage
means engine overheating and perature drops. is observed.
warning lamp lights up. In such a
case stop driving, park your vehicle Wait until the Check that radia-
without stopping the engine. On engine coolant tor fan is operat-
the contrary, stopping the engine temperature ing. Consult au-
when it overheats may cause a sud- drops below thorized TEMSA
den rise in coolant temperature and 100 °C/212 °F. Service, before
the engine to locked up. continuing to
drive, in case of malfunction.
Hot Surfaces
Wear protective gloves during
inspection of engine compart- Warning
ment. Hot parts may cause se- Never open the radiator filler
vere injuries. cap when engine overheats.
Warning lamp I
Lights up in addition to
any warning lamp. Stop
the vehicle immediately and consult
authorized TEMSA Service.
Information
Warning lamp II
02 Vehicle
Lights up in addition
to any warning lamp.
When the lamp is on, it is advised
not to continue to driving.Take the
necessary actions immediately for
the corresponding warning lamp.
Flashes as long as left
Indicates that parking
or right direction indi-
brake is activated.
cator is activated.
Information
And an audible warning is given to
driver with some malfunctions.
02 Vehicle
Consult
Authorized
TEMSA
Service
If warning panel is
Warning panel informs driver to ve- Use menu selection buttons to shift- In case of malfunction, envelope non operational, do not drive
hicle’s operating status, malfunc- ing between pages. icon displayed with a number that and consult authorized TEMSA
tions and information about the signifier how many fault message Service.
software. exist. Hold button “1” a few sec-
Turn ignition key on position “2” to onds to display fault message menu.
operate warning panel.
If an envelope with “x” mark dis-
played, this means no malfunctions.
Information
Adjust warning panel bright-
ness for a clear visibility by
using Dimmer Switch located
on left control panel. (See also
page 33)
0 20 40 60 80 100
Hold button “2” a few seconds to Hold button “4” a few seconds to
reach diagnose screen. reach diagnose screen.
Front left, front right, rear left and
Use warning panel buttons to shift rear right brake lining levels dis-
between the diagnose screen con- played in this menu.
tent. Button functions are stated
below:
Press button 2 to shift next malfunc-
tion.
Button 2: Down
Button 3: Up
Button 4: Select
Information
Button 5: Exit
Accuracy rating of brake lining
sensor is %5.
Information
02 Vehicle
Hold button “5” a few seconds to Hold button “6” to display informa-
reach oil pressure indicator. tion about the vehicle.
Displays current engine oil pressure.
The current engine oil pressure is
displayed in the electronic menu of
the warning panel.
Visual
Inspection
Check oil pressure
regularly during driving. Stop
the vehicle if the warning lamp
lights up.
Driving Menu
Kneeling-lifting active
Gearbox oil tempera-
ture warning First alternator failure
02 Vehicle
Information
Warning
02 Vehicle
Gearbox failure High Exhaust System
Temperature
DEF low
ABS active
Warning Lamp II
02 Vehicle
Warning Lamp II
Fault Gearbox General gearbox error Available
(Yellow)
Electric Drive Fault 1 Alternator Alternator 1 is not charging or insufficient charg- Warning Lamp II
Unavailable
Down ing (Yellow)
Information
Electric Drive Fault All Alternators Alternators are not charging or insufficient charg- Warning Lamp II
02 Vehicle
Unavailable
Down ing (Yellow)
Fire Warning Fire break out on vehicle. Warning Lamp I (Red) Available
No Battery Charge
Battery voltage is under 23 V. Warning Lamp I (Red) Unavailable
Voltage Low
Warning Lamp II
Luggage Compartment Luggage compartment lid is open. Unavailable
(Yellow)
Front Brake
Front axle pressure is high. Warning Lamp I (Red) Available
Air Pressure High
Rear Brake
Rear axle pressure is high. Warning Lamp I (Red) Available
Air Pressure High
Warning Lamp II
Check Diagnostics Diagnostic failure. Unavailable
(Yellow)
WC Tanks Full/Empty Toilet clean water tank empty or lavatory waste Warning Lamp II
Unavailable
Check Diagnostics tank is full. (Yellow)
Information
WC Emergency
02 Vehicle
Toilet emergency button pressed. Warning Lamp I (Red) Available
Warning
STEERING
Information
CONTROL
2 3
02 Vehicle
1 Steering Wheel
Position Adjustment
2 Left Control Lever
3 Retarder Control Lever To adjust steering wheel position,
(Optional) press “Steering Control Switch”
located on left control panel. (See
also page 32) Warning
• Never drive before relocking
Adjust the position of steering the mechanism.
wheel to the desired position. Press • Steering wheel adjustment
button again to lock the mecha- must be performed only
nism. when the vehicle is station-
ary and the parking brake is
It is suggested to adjust the position activated.
of drivers seat, before adjusting the
steering wheel position.
Information
02 Vehicle
Enables the control of headlamps, To turn on upper beam headlamps Push the control lever to the first Press button to activate the horn
upper beam headlamps, turn sig- continuously push the control lever level. The lever returns to “Off-Po- briefly.
nals, horn and windshield wipers. to second level. sition” when it is released.
Visual Visual
Information Inspection Inspection
None of the functions can be Warning lamp locat- Warning lamp locat-
used when the ignition key is ed on warning panel ed on warning panel
switched off. lights up as long as lights up unless the
the upper beam headlamps lever is released.
are on.
Move the control lever forward to Move the control lever toward you Adjust the speed of wipers by rotat- Push the lever in the direction of the
utmost degree to activate right turn to utmost degree to activate left ing the front part of control lever in arrow to spray washer fluid and acti-
signal. turn signal. the direction of the arrow. vate the windshield wipers to wipe
three times.
0: Windscreen wipers are off.
Visual
: Intermittent
Inspection
Corresponding warn- Information Information
I: Slow wiping
ing lamp located on When the steering wheel is To wash and wipe the wind-
warning panel flashes turned to its normal position, shield continuously, hold the
II: Fast wiping
as long as right or left turn sig- turn signal is switched off au- front part of the lever toward
nal lever is activated. tomatically. steering column.
BR
Information
must be applied in addition
AKIN
to retarder in such a case.
• Never activate retarder
02 Vehicle
G
Information brake on slippery road, tires
• Retarder system has five might get blocked and ve-
levels. hicle might sway.
• First level of retarder system
PO
maintains a steady speed on
W
gradients.
ER
• Vehicle prolongs accelerat-
ing at first level of retarder
system, as long as the accel-
erator pedal is pressed.
• Retarder cannot be applied
under speed of 30 km/h.
(18.64 mph).
Open the access hatch. Pull the cap
of the tank and pour the fluid into it. Consult
Authorized
TEMSA
Service
Consult with the near-
Option est authorized TEMSA
Warning This feature depends on cus- service if retarder fault
Always use clean and filtered tomers request. It may not ex- warning appears on
washer fluid. ist in all models of the vehicle. display.
APPLY
ASE
BR ING
E
E
REL
AK
RK
TO
PA
PUL
PUSH TO
12 V 12 V
Information
02 Vehicle
Visual
Prevents the vehicle from sliding Inspection Warning
after it is brought to a stop. “PARKING BRAKE”
Check the air pressure of the
lamp located on indi- system if the warning lamp
To activate the parking brake, pull cator panel lights up does not turn off although the
the lever upwards (1). when the parking brake is ac- parking brake is released. In
tivated. It turns off when the such a case consult authorized
To release the parking brake, push parking brake is released. TEMSA Service before continu-
the lever downwards (2). ing to drive.
Warning
Never activate the parking
brake while driving except in
emergency situations.
Option 1
Option 1
12 V 12 V
12 V 12 V
12 V 12 V
12 V 12 V 12 V
12 V
Information
02 Vehicle
Option 2
Documents and other non heavy auto
Option 2
auto auto
Information
02 Vehicle
Option
Rear view mirrors may vary ac-
cording to customers request.
4
1 2 3
1 2
1 2
Option
02 Vehicle
4
1 2
3
1 2
Hazard Warning
Drivers Reading
Interior Light Flasher Switch
Lamp Switch
Switch Press upper side of
Press upper side of
DRIVER INTERIOR
Turns on corridor HAZARD the switch to acti-
LIGHT
the switch to turn LIGHT
Information
pressed, indicator led on the switch,
turn signal indicators on the indica-
tor panel and all signal lamps start
Information
02 Vehicle
Reading Light flashing.
Switch 1st Position: Three lamps at
Press lower side of the hazard warn-
READING
Turns on passangers’ the right hand side and three
LIGHT ing flasher switch once again to de-
reading ligts. lamps at the left hand side
active flashers.
light on.
2nd Position: One lamp at the
right hand side and two lamps
at the left hand side light on.
STOP
Start-Stop Switch 3rd Position: Off Position Information
Night Light Switch
Hazard warning flashers can
ENGINE Runs and stops the Turns on night ligts.
be activated even if igniton
engine. NIGHT
START LIGHT
key is removed.
Information
Aisle Lights Switch Front Door Control Hazard warning flashers are
Press upper side of Switch also activated when the
AISLE
LIGHT the switch to turn FRONT
Opens the front “Emergency Stop Switch” is
DOOR
aisle lights on. door from driver’s pressed.
compartment.
SELECT
Upshift switch
02 Vehicle
MONITOR
Downshift switch
Option
Automatic transmission model
varies according to customer
requirements. R Reverse gear switch
3 different keys are provided with Ignition Key Fuel Tank Access, Front Door, En-
the vehicle. gine Compartment, Service Hatch
Key and Glove Box Key
In case the keys get lost, consult
authorized TEMSA Service to order.
Information
Option
02 Vehicle
Keys of new additional
equipment may be different
from those indicated in user’s
Toilet Door Key
Manual.
Pull the armrest upwards to the ut- Pull the lever in the direction of the
most degree to open it. Release the arrow to adjust upright position.
Option armrest after it is locked. Armrest
Model, type and specifications would stay stationary at that posi-
of passenger seats may differ tion.
from those stated in this User’s
Manual. To close the armrest, pull the arm-
rest to the utmost degree again
and push to lowest level after it is
released.
Warning
Passenger seat bolts tightening
torque must be 65 Nm. Check
the torque before driving.
Interıor
against retractor to confirm
03 Vehicle
that automatic lock mecha-
nism is working properly.
Consult with authorized
TEMSA service in case of any
Use of Seat Belts for Pregnant Use of Seat Belts for Children
extreme degree, sliding may belt is fastened at the proper tight- vents from severe injuries.
occur resulting with injuries. ness in order to prevent the passen-
ger from sliding off the seat.
Information
Warning Check that seat belts are cor-
• Passengers should not walk rectly seated and they func-
Proper usage of seatbelts during in the vehicle unless neces- tion properly during travel and
pregnancy will not affect babies or sary. tighten if necessary.
mothers adversely. • Each seat belt is allowed to
be used individually. Only
Seat belts should be fastened from use one seat belt per per-
the lower side of abdomen by preg- son.
nant so as to prevent compression. • Replace any seat belts
which have been damaged,
Passenger seat should be kept at stained or teared.
the upright position as much as • Children of ages 0-10
possible to provide safer use for should by no means be per-
Press the latch on the belt buckle to pregnant.
release the seat belt. mitted to wander in the ve-
hicle if unattended by their
parents.
Option
This feature is optional. It may
not be included in all models.
Interıor
Warning
03 Vehicle
• Assistant’s seat and its con-
nection parts are tested and
approved.
• Usage of different types of
assistant’s seat may cause 2
accidents and severe inju-
ries.
5
3
6
Interıor
1
03 Vehicle
4 5
2
Press button to turn on reading
lamps.
1. Air Vents Move the air vents wings to desired
2. Reading Lamp Button location to allow the air out.
3. Assistant Call Button Option
4. Speaker Button This feature is optional. It may Information
5. Reading Lamp not be included in all models. Press “Reading Light
6. Speaker Switch” located on
right control panel to
activate passenger reading
lamp switchs. (See also page
59)
Interıor
03 Vehicle
casting for the passengers.
Visual
Inspection
When the button is
pressed, warning lamp locat-
Information ed on assistant’s compartment
Refer to user’s manuals lights up.
of sound system deliv-
ered with the vehicle
for more information.
Information Option
The fire extinguisher is to be Location of fire extinguishers
used in the event of a fire to and their volume may vary ac-
prevent the fire from spread- cording to customers request. 1
ing. Location of the fire extinguish-
Interıor
Driver Duties • Avoid any overheating. • Make a visual check of the engine 7. Inform the appropriate emer-
1. Before starting a journey, the compartment and surrounding gency services, giving as much
driver must check: equipments of the vehicle and information about the incident or
• The tire pressure (visual check inform the technician of any accident and passengers involved
on a daily basis - test tires on a Warning problem. as possible.
weekly basis). Stop any overheating if the 4. When returning a coach: 8. Where appropriate and safe to do
• No liquids are leaking on pave- engine, brakes or retarder • Park the vehicle with the main so, use the fire extinguishers to
ment (visual check). become overheated/or when battery switched off (if appli- put out fires / do not open the
Interıor
03 Vehicle
sensing unusual odours or cable). This will disconnect the engine compartments if fire oc-
smoke, or if noticing smoke batteries from the alternator, curs.
visually. eliminating a risk of fire due to 9. Put on warning vest and place
Warning an internal electrical failure. the self-standing warning signs
Ensure that no oil exits from • Park in a safe and clean area. as appropriate / Secure the inci-
the muffler and that you see • Avoid overloading because it in- Actions to Be Taken In The Event dent area.
no excessive blue smoke (tur- creases all temperatures! Of a Fire 10.Make sure that passengers are
bocharger oil consumption). • Record in the daily operation at a safe distance from vehicle.
report malfunction(s) with mile- 1. (Try to) park the vehicle in a safe 11.Move away from the vicinity
• The proper functioning of the ages and time. area. of the accident or emergency,
preheating systems (engine and • Check the ABS warning light. 2. Apply the parking brake. advise other persons to move
interior). • Check the proper functioning of 3. Inform passengers to move a safe away and follow the advice of
• The exhaust system components the retarder (hydraulic or elec- distance away from the vehicle. the emergency services.
are free from debris. tric). 4. Open door in order to let passen- 12.Report to company manage-
2. When operating a vehicle, the 3. After completing a journey, the gers get out fast. ment about the incident.
driver needs to: driver needs to: 5. Stop engine / isolate the bat-
• Check the coolant temperature • Inform the technician / next tery by deactivating the main
gauge. driver of a disfunction. battery cut-off switch (See also
• Hand over to the technician or page 168). Switch off the air-
fleet manager the daily operation conditioning / heating.
report (copy). 6. Identify the source of the fire.
In the event of a possible fire, evac- Your vehicle is equipped with emer-
uate the passengers to a safe area. gency windows on both left and
Always evacuate women and chil- Information right side. Emergency windows are
dren first. • Take
the direction of the denoted with special labels. Check
wind into consideration, do the windows are functioning prop-
not discharge agent against erly and the labels are legible.
the wind.
Interıor
Warning
03 Vehicle
Information
Opening handles are only
installed on emergency win-
dows.
Interıor
03 Vehicle
Pull one of the red handle to upright Push the emergency exit window af-
position to release the lock mecha- ter the lock mechanism is released.
nism.
Interıor
03 Vehicle
exit valve clockwise and push the
door outwards to open.
UNLOCK
Warning
• Never remove the labels
stuck on the emergency exit
windows.
• Never use escape hatches
1
3
when the vehicle is not sta-
tionary.
Interıor
03 Vehicle
In an emergency;
1. Push up
2. Pull the white knob
3. Open the lid
Interıor
03 Vehicle
Pull the black knob to move the sun
visor downwards.
BLIND
LEFT BLIND
RIGHT
Keep lower side of the blind left Keep lower side of the blind right
switch pressed to lower driver’s sun switch pressed to lower assistant’s
visor. sun visor.
Information
Sun visor control buttons are
located on left control panel.
Assistant’s Microphone
(Optional) Lateral Glove Box Dashboard Refrigerator Rear View Mirror
Interıor
03 Vehicle
Information
Refer to user’s manuals
of dashborad refrigre-
ator delivered with the
vehicle for more information.
Interıor
03 Vehicle
Indicates that passengers must fas-
ten their seat belts.
max.
Warning
lbs
Kg 3k g/6.lb s • Take necessary precautions
while opening and closing
overhead luggage hatch.
Interıor
03 Vehicle
Hand Washing
Button
Interıor
03 Vehicle
WC ACTIVE
Flush
Button
Your vehicle is equipped with toilet Push “WC Active” button located
unit and denoted by label. on the left control panel to activate
toilet system.
Warning
Information about toilet usage
is denoted by warning labels.
Inform passangers before us-
ing toilet.
STOP
Interıor
03 Vehicle
Warning Information
Lavatory waste must be dis- If lavatory waste tank is full,
posed of into appropriate and a fault message displayed on
approved Disposal or Dump. warning panel.
Failure to do so may result in
Interıor
serious criminal and/or civil
03 Vehicle
fines, penalties and/or incar-
ceration.
Warning
Never use toilet unit if lavatory
1. Park the vehicle in a dump station waste tank full.
and place your holding tank drain
valve as close to the opening of
the dump station as possible.
2. Pull the discarge valve lever
down. Warning
3. Restore the valve to its original If the weather is cold, (under
position when discharging is 32oF / 0oC) water tank and
finished. water pipes may be frozen. To
avoid damage, drain lavatory
waste tank and clear water
tank if the vehicle is to remain
unused long period of time.
Warning
If the weather is cold, (under
32oF / 0oC) water tank and
water pipes may be frozen. To
avoid damage, drain lavatory
Interıor
03 Vehicle
FLUSH
Flush Button
Interıor
03 Vehicle
WC ACTIVE
STOP
Interıor
03 Vehicle
Warning Information
Lavatory waste must be dis- If lavatory waste tank is full,
posed of into appropriate and a fault message displayed on
approved Disposal or Dump. warning panel.
Failure to do so may result in
Interıor
serious criminal and/or civil
03 Vehicle
fines, penalties and/or incar-
ceration.
Warning
Never use toilet unit if lavatory
1. Park the vehicle in a dump station waste tank full.
and place your holding tank drain
valve as close to the opening of
the dump station as possible.
2. Pull the discarge valve lever
down. Warning
3. Restore the valve to its original If the weather is cold, (under
position when discharging is 32oF / 0oC) water tank and
finished. water pipes may be frozen. To
avoid damage, drain lavatory
waste tank if the vehicle is to
remain unused long period of
time.
Taking necessary actions before Check the tires and rims before Check fuel and lubrication systems Check the level of coolant before
driving prevents possible problems driving. of the vehicle for leaks before driv- driving (see page 129).
while driving. ing.
Visual Visual
To have optimal conditions for your
Inspection Visual Inspection
own and passenger’s safety, always
Check that tires (also
Inspection Consult authorized
check all items that may affect driv- Consult authorized
spare tires) are not worn, torn, TEMSA Service when
ing performance. TEMSA Service in case
damaged etc. TEMSA coolant level is low.
04 drıvıng
Check the level of windshield wash- Check that air conditioner drain off Check the emergency situation Check the fuel level by using the
er fluid before driving. Top up the nozzle is not blocked. equipment before driving. Check corresponding indicator located on
fluid if the level is low (see page the emergency equipment is fully instrument panel. Top up the tank
53). functional. with correct fuel if needed.
Jack, spare tire, bulbs, spare fuse, Do not wait until the fuel is
first aid kit, fire extinguisher, wheel completely consumed before
Warning refueling. Air remaining inside
04 drıvıng
nut, lug wrench, chock, auxiliary
Hard water minerals may block
rods and tool bag must be kept the tank may cause engine
the washer sprays.
ready for use. malfunction.
According to traffic conditions sud- Knob at the end of the air condi-
den acceleration and deceleration tioner nozzle may get blocked due
may cause luggage sliding and to weather conditions.
Information
• C heck that first aid kit con-
hitting the luggage compartment
tents are complete.
walls. Arrange the luggage in order The performance of the air condi-
• Check the fire extinguisher
to prevent this. tioner would be inversely affected if
has been serviced.
condensate is not drained off.
Adjust the height of the seat by pull- Pull the button to loosen seat When the button is pressed, air in
ing/pushing the button. springs. Push forward the button to the system is released and height
Information harden seat springs. of the seat decreeases.
Ensure that seat system con-
tains air before performing
height adjustment. See also
“Fast Descend” to have infor-
04 drıvıng
mation about how to fill air
inside the seat system.
Keep the button pulled to adjust the Adjustment lever is located at the Keep the button pulled to perform Keep the lever pulled, adjust to the
cushion depth to desired position. left hand side of the driver. Pull the cushion forward and backward slide desired position and then release
Release the button to stabilize the lever at utmost degree, adjust the adjustment. Release the button to the lever to stabilize the seat.
cushion’s position. seat to desired position and then stabilize the seat.
release the lever.
04 drıvıng
04 drıvıng
Rev. 05 / 30.04.13 TS 30|95
4.1.2 Driver’s Seat Belt 4.1.3 Rear View Mirror 4.1.4 Steering Wheel
Sight Adjustment Adjustment
Insert the buckle latch into the
First adjust the seat, put on the Adjust the positions of the rear view Always check steering wheel posi-
belt buckle until it engages with a
seat belt and then perform other mirrors before driving (see page tion before driving (see page 50).
click. Press the red button on the
actions. 57).
belt buckle to release the belt. Belt
should coil automatically.
Information Information
Before driving, first Adjust the seat posi-
adjust the seat po- tion first, put on seat
04 drıvıng
Warning
Changing steering wheel posi-
tion when driving will reduce
control over the vehicle and
Warning could cause accidents.
Do a seat belt check once a Click
week by pulling it while it is
engaged, it should not release.
Check that all control switches func- Indicator and warning lights pro- Check that air pressure is enough
tion properly before driving. vide all the information about the to operate brake and other systems.
operations of the vehicle. It is of
vital importance to check all of the
indicator and warning lamps before
driving.
Information
All control switches
WARNING
function after main
04 drıvıng
DO NOT OPERATE THE BUS
TEMSA battery cut-off switch WITH AN AIR PRESSURE
is switched on. Consult BELOW 100 PSI
authorized TEMSA Service if Warning
any of the switches malfunc- Warning lamps may indicate
tion. any malfunction during travel.
Always find out the reasons
for the malfunction. Park the
vehicle in a convenient place
and consult authorized TEMSA
Service if you cannot detect or
repair the malfunction.
04 drıvıng
adjustment, bring the ignition key
to position “2” and press lower part
of the start-stop switch. Information
• Steering wheel will lock up
Only start the engine when “Neu- if it is rotated when the igni-
0 :Ignition key can be removed MONITOR
tral” gear is engaged. tion key is removed.
in this position after engine is
• To release the steering
stopped
wheel, switch the ignition
1 :Engine shut down position.
key to position “1” or “2”
2 :In this position electrical sys-
while rotating the steering
tem is active although engine is
wheel to the left and right.
stopped. STOP
EAS
E
REL
AK
RK
PUSH TO
Information
04 drıvıng
Warning
Never switch off the ignition
while driving. This may cause
the steering wheel to lock up.
04 drıvıng
ment when parking uphill. APPLY
Warning and information labels are
E
BR ING
EAS
E
AK
REL
RK
TO
PA
When the engine coolant temper-
PUL
PUSH TO
Information
ABS system will be deactivated
when the parking brake is ac-
tivated.
Simple problems may cause failure of the engine. There are some appli
Visual cations that can be done before consulting the authorized TEMSA Service.
Warning Inspection
Sudden rise in cool-
Never open radiator cap when
ant temperature may indicate
the engine is hot. Emergency Stop Switch Release the Emergency
damage to the belt.
could be pressed. Stop Switch.
Consult
Hot Surfaces Authorized
Accessible parts would be hot TEMSA Service
when the engine maintenance
Consult authorized TEMSA
lid is opened. Empty Battery.
Service in such a case before
driving. Check the battery charge.
Replace battery.
04 drıvıng
shift to “Neutral” before towing
process.
WARNING
• Always tow the vehicle at low
In a dangerous situation, tow-
speeds.
ing without seperation of the
Information • Resolve the problem mechanical-
Warning drive train is permitted until
• Tow rope length can be 5 ly in case of system air pressure
Technical knowledge is need- the vehicle has left the danger
meters / 16,4 ft and tow malfunctioning (see also page
ed for towing. Only road re- area (e.g. intersection, tunnel
bar length can be maximum 162).
covery service must perform etc.).
1 meter / 3,28 ft. • Check that tow rope, chain is
this application. In such a case the following
• Red warning signs must be parallel to the road during the
conditions apply:
attached on tow ropes lon- towing process.
• Maximum towing time: 10
ger than 2.5 meters/8.2 ft. minutes
• If the lighting system of • Maximum speed: 9,3 mph /
Information the towed vehicle is mal- 15 km/h.
INFORMATION
• Maximum speed limit is 9,3 functioning, a 0,65x0,65ft
At an ambient temperature
mph / 15 km/h for vehicles /20 x 20 cm red reflector
below -15˚C / 5˚F, the maxi-
with brake problems. must be placed behind the
mally permitted towing speed
• Maximum speed limit is vehicle.
is 3,11 mph / 5 km/h.
12,5 mph / 20 km/h for
vehicles with no brake prob-
lems.
page 162.
Ensure the parking brake sys-
tem function again before
towing.
Warning
After removal of the propeller
shaft, place gearbox in a neu-
tral position.
It is located at inside part of the Make sure the tow rope is parallel It is located on rear bumper.
front bumper. Pull the cover of tow to the road during the towing pro-
located on front bumper and fix the cess. Otherwise it may cause serious
tow hook. damage to the vehicle.
TRUE
04 drıvıng
First deactivate FALSE
the parking brake.
Switch the ignition
key to position “2” Use rear towing hook to tow any
and shift into “Neu- vehicle.
tral”.
Ignition must be on position “1” or FALSE
“2” during towing process. Never
remove the ignition key, otherwise
steering wheel will lock.
Corridor Lamps Driver’s Reading Lamp Passengers’ Reading Lamps Passengers’ Night Lamps
NIGHT
LIGHT
DRIVER
LIGHT
INTERIOR
LIGHT
05 headlamps
and lamps
Step Lamps Entrance Illumination Lamp Aisle Illumination Lamp Parking Lamps
AISLE
LIGHT
05 headlamps
and lamps
auto auto auto
Information
Consult authorized TEMSA Ser-
vice in case of parking lamp
malfunction.
Brake lamps light up as long as the Indicates to other drivers that the
brake pedal is pressed. driver intends a lateral change of
position. They are located: 2 on
Your vehicle is equipped with seven front and 2 at rear, 2 on each side.
brake lamps, four are located at rear
lamp group and three are at the
05 headlamps
Information
• Indicators are controlled by
left control lever located on
the steering wheel control
Information group.
Brake lamps also light up when • Consult authorizedTEMSA
the retarder brake system is ac- Service in case of turn signal
tivated and switched off when malfunction.
it is deactivated.
Warning
Check that all brake lamps
function properly before driv-
ing. Consult with authorized
TEMSA service in case of mal-
Warning function.
Never cover parking lamps
with paint or label etc.
05 headlamps
and lamps
Information
Information Ignition key must be on posi-
• C
onsult authorized TEMSA
tion “2” to light up luggage
Service in case of rear di-
compartment lamps.
rection indicator lamp mal-
function.
• When the reverse gear is
shifted, hazard warning
flashers start flashing and
buzzer sounds.
ness.
Information
Consult authorized TEMSA
LOW BEAM
Service in case of license plate CLEARANCE
lamp malfunction.
Provide long range visibility during Enables higher visibility of the front
travel. See also page 51 to acti- part of the vehicle in wintry condi-
vate upper beam headlamps. tions. Press “FRONT FOG LAMP” but-
ton located on left control panel to
turn the fog lamps on.
05 headlamps
and lamps
Information
Upper beams are used when Information
the lower beams are insuffi- • Turn the fog lamps on only
cient to provide high visibility. when required by weather
conditions. Unnecessary use
of fog lamps may cause ac-
cidents.
• Abide to country laws.
Visual
Warning Inspection
Information Upper beams will adversely af- Warning lamp locat-
• Position the “PARKING LAMP
fect the visibility of the driver ed on warning panel
AND LOW BEAM SWITCH”
on the opposite side. Never lights up as long as the
located on the left control
use the upper beams if not upper beam headlamps are on.
panel to the second level
necessary.
to turn on the lower beam
headlamps.
• Consult authorized TEMSA
Service in case of low beam
headlights malfunction.
Information
Warning Lock protection cap prevents
Never use door opening
dust, oil, etc. from contami-
switches if the door is locked.
nating the lock mechanism.
This could result in damage to
Always keep the cap closed
the locking mechanism.
after use.
Warning
Never use door opening
switches if the door is locked.
This could result in damage to
the locking mechanism.
6 7 8 8 9
The locking mechanism is dedicated Push the lid downwards and turn The locking mechanism is dedicated Push the lid and turn the key clock-
to locking or unlocking the lid. the key clockwise to lock the mech- to locking or unlocking the lid. wise to lock the mechanism.
anism.
Warning Warning
Always hold the handle while • Always hold the handle
opening and closing the lid. while opening and closing
Never hold edges and inner the lid. Never hold edges
parts of the lid. Your hand may and inner parts of the lid.
get caught. Your hand may get caught.
• Do not use this area for stor-
age.
press the latch to release the lock- press the latch to release the lock-
ing mechanism and continue to pull ing mechanism and continue to pull
sideways movement. sideways movement.
Warning Warning
Never hold edges or inner Never hold edges or inner
parts of the lid while closing. parts of the lid while closing.
Your hands may get caught. Your hands may get caught.
The locking mechanism is dedicated Push the lid and turn the key clock- The locking mechanism is dedicated
to locking or unlocking the lid. wise to lock the mechanism. to locking or unlocking the lid. To
open the lid turn the key anti-clock-
Warning
Warning
• Always hold the handle
while opening and closing
the lid. Never hold edges
and inner parts of the lid.
Your hand may get caught.
• Do not use this area for stor-
age.
The locking mechanism is dedicated Push the lid downwards and turn The locking mechanism is dedicated Push the lid and turn the key clock-
to locking or unlocking the lid. the key clockwise to lock the mech- to locking or unlocking the lid. wise to lock the mechanism.
anism.
06 dOOrs and lids
Insert the key in its lock and turn Insert the key in its lock and turn
anti-clockwise. Pull the handle as anti-clockwise. To open the lid pull
shown in the figure and lift the lid. it until it stops, press the latch to
Warning
release the locking mechanism and
• Always hold the handle
continue to pull sideways move-
while opening and closing
ment.
the lid. Never hold edges
and inner parts of the lid.
Warning Your hand may get caught.
Always hold the handle while • Do not use this area for stor-
opening and closing the lid. age.
Never hold edges and inner
parts of the lid. Your hand may
get caught.
The locking mechanism is dedicated Push the handle to the right to open
to locking or unlocking the lid. To fuel tank cap.
open the lid turn the key anti-clock- Information
Warning
Spring mechanism is provided
on the cap. When the handle
is pushed, cap is released au-
tomatically.
The locking mechanism is dedicated To open the lid turn the key clock-
to locking or unlocking the lid. wise and pull the handle to open,
to close push and turn the key anti-
06 dOOrs and lids
clockwise.
Warning
• Always hold the handle
while opening and closing
the lid. Never hold edges
Hot Surfaces and inner parts of the lid.
When opening the engine Your hand may get caught.
maintenance lid beware of • Do not use this area for stor-
hot surfaces. age.
Your vehicle is equipped with die- Prevents the start up of the engine High temperature formed during
sel technology which is designed and avoids possible accidents when the operation of the engine is de-
to provide a safe, economical and Warning the maintenance lid is opened. creased by engine coolant.
efficient driving experience. • N ever allow unauthorized
people to drive the vehicle.
Remove the ignition key
Safety Warnings before operating on the en-
gine compartment.
Check that general safety rules, all • Always stop the engine and
warning signs and information are wait until it’s cold before
07 engıne
07 engıne
engine temperature is hot. Check the coolant level when • Never fill up the tank only
Pressurized steam may es- the engine is cold. Coolant with antifreeze.
level must not be below “MINI-
cape from tank. Warning • In addition to this, anti-
• Never remove the expan- MUM” sign on the tank. freeze protects the engine
Engine coolant must be re-
sion tank cap completely at placed periodically only by au- against overheating as it
once. Turn the cap slowly thorized TEMSA Service. increases the boiling point
to release the pressurized of water.
steam. Then remove the cap
completely. Warning
Coolant level increases as its Freeze Protection Temperatures for Anti-
temperature rises. Over-filled freeze Concentrations (1)
tank may overflow. Protection to: Concentration Warning
-24˚C (-12˚F) 40% glycol, 60% water • Addition or replacement
-37˚C (-34˚F) 50% glycol, 50% water
processes of engine coolant
must only be performed by
-52˚C (-62˚F) 60% glycol, 40% water authorized TEMSA Service.
(1)
Ethylene glycol-based antifreeze • Contact with engine cool-
ant may cause irritation on
skin and eyes. If this occurs
seek medical help.
07 engıne
system.
Information
For more information about
air filter maintenance and re-
placement (see page 178).
07 engıne
EM
CY
steering hydraulic tank filter.
STOP
Warning
To reinstall the cap, turn clock
07 engıne
wise.
Start engine by
pressing “Engine Warning
Start” button. Rotate “Emergency Stop” but-
ton clockwise to bring it into
first position and turn “Ignition
Switch” to “OFF” position after
stopping the engine.
Manual Regeneration
07 engıne
sprayed in engine compartment
room. WARNING
Detector tube and
extinguisher cylinder
bar
Information Information
When ambient temperature ush D for forward or R for
P
SELECT Warning is below -15 °C/5°F keep the reverse to shift the transmis-
Never select R while the ve- engine running in idle speed sion into a desired range or
hicle is in forward motion. until the engine temperature gear temperature reaches
reaches 40 °C/104°F. 40 °C/104°F.
lower engine speed to achieve the The vehicle performs at maximum By pressing the Mode Button the
lowest possible fuel consumption. power when it is activated. Power mode is selected and the red
08 transmission
LED on the right top corner will light
MONITOR
up to show the mode is selected.
Information Information
Driving mode can be selected Fuel consumption increases
at any time. when powerful drive mode is
activated.
When the transmission shifts into
reverse gear, the display will have
an R in both locations. There is only
one reverse gear.
Downshift Button
To select the gear manu-
ally press Downshift But-
ton.
The controls will automatically • M ove your foot off the accelera-
select the Economy shift strategy tor pedal.
when an unloaded state of the vehi- LBSS Drive Mode Information • Apply service brake till the ve-
cle is detected (based on capability The mode is used when Fuel consumption increases hicle stops.
of the vehicle to accelerate quickly), powerful driving is re when powerful drive mode is
then automatically switch to the quired. activated.
Performance shift strategy when The vehicle performs at maximum
the vehicle is loaded and its ability power when it is activated. Information
to accelerate is reduced. The re- For short term stopping use
sulting operation can continuously the service brake, for longer
modify transmission shifting to keep
Option stops shift into neutral gear
the engine near its more efficient Information and use service brake.
LBSS system is optional. It may
speed range. This can produce im- Press MODE button while not exist in all models of the
proved overall vehicle fuel economy LBSS Drive Mode activated to vehicle.
while still enabling high productivity switch economic drive mode.
when the vehicle is loaded. If your vehicle is fully loaded,
LBSS Drive Mode activated Warning
The red LED on the right top corner again automatically. If the driver should leave the
will light up when economic drive driver compartment with the
mode is selected. engine running. Neutral (N)
gear must be engaged and
parking brake must be acti-
vated.
Consult
Authorized
TEMSA Service
Stop the engine and consult
authorized TEMSA Service in
case of air bellow malfunction.
Air bellow compression can be Your vehicle is equipped with a Kneeling Lifting button enables
changed in order to adjust the ve- Front Kneeling System to ease the adjustment of body leveling. The
hicle body height from the ground. Warning entering and exiting of passengers. warning lamp on the button lights
• D
o not continue driving if up as long as the kneeling-lifting
you encounter a problem operation is being performed. Press
with the KNEELING-LIFTING lower side of KNEELING-LIFTING
system. button located on the left control
• Before jacking up the ve- panel to decrease the body height.
09 SUSPENSION
hicle, deactivate the KNEEL-
ING - LIFTING system. KNEELING BUS
KNEELING &
Authorized
TEMSA Service
Consult authorized TEMSA Ser- Information
vice in case of kneeling-lifting Body height can be decreased
Information malfunction. by maximum 80 mm/3,14
The bus is equipped with inch.
kneeling system that consist
of an outside warning lamp at
the frame of front door and a
buzzer. Kneeling lamp flashes
and beeps during the kneeling Information
system is active. If Kneeling system was acti-
vated, transmission won’t en-
gage.
mph.
Thus, 265 millimeter width, 50 % indicates plant code, tire size and figuration. Dual Tire Maximum Load Tire pressure increases while
aspect ratio, radial type and rims of manufacture date of the tire. Tire for your vehicle is 3150 kg (6940 driving. Check tire pressure
19.5 inches tires are used. Identification Number for your ve- lbs) at 775 kPa (12,4 psi) cold. when tires are cold.
hicle is 562742.
Check the tire pressures before pro- It is suggested to use snow tires to
longed driving. provide better traction on snow
Warning and ice.
Check the tire pressures once a • Extremely Low Tire Pressure
week when they are cold. causes tire overheating, in-
creases fuel consumption
Always check the tire pressures with and reduces road handling.
a pressure gauge. Appearance of Low Proper High • Overloaded tires with ex-
the tire can be misleading. tremely low pressure have
a high risk of inflation.
The wrong tire pressure will have an • Extremely low tire pressure
10 tires
effect on safety. can deteriorate the tire con-
dition and could cause the
Warning tire to release from the rim
• E xtremely high tire pressure fixation.
Warning increases wear of tires, brak-
Pressures of tires on the same ing distance and reduces
axle must be equal to maintain road handling.
the brake stability. Having dif- • Tire pressure rises after pro-
ferent pressure values may longed driving especially in
cause inaccurate and instable hot conditions. Do not de-
braking power. flate the tires when they are
hot. Pressure adjusted in hot
conditions might be insuffi-
cient in cold conditions.
Visual • Objects such as nails, gravel
Inspection etc. inside the tire treads
Check the tires visu- may cause continuous defla-
ally and ensure that they are tion of tire pressure. Check
in good conditions. the tires regularly.
E AS
BR ING
RELE
E
AK
RK
possible. When using snow chains, Vehicle jack, wheel chock and aux-
TO
PU L
PA
PUSH TO
Remove the rim covers Loosen the wheel nuts Use of jack
First ensure the vehicle is secure Loosen all the wheel nuts with a lug Rotate the screw anti-clockwise and
and then remove the rim cover of wrench in a crosswise pattern. push the jack piston downwards to
the wheel to be changed. Information release the jack.
Lug wrench is located inside
the tool box in the emergency
equipment compartment.
10 tires
Hold the safety spring behind the
hub cap and pull it outwards. Re-
move the hub cap.
Warning
Never remove the wheel nuts
before the vehicle is jacked up.
10 tires
50 km/31miles.
Warning
Check the wheel nuts regularly
to ensure that they are cor- Remove the wheel nuts in a cross-
rectly seated. Retighten the wise pattern using a socket wrench
nuts if necessary. It is essential and take off the wheel. Take care
to retighten the wheel nuts of The mechanism moves upwards as not to damage the wheel stud
Warning
Always fit new tires on the
a changed wheel after 50 km. the lever is rotated counterclock- threads.
front of the vehicle.
wise.
Fit the new tire and tighten all the
SPARE TIRE wheel nuts gently in crosswise se-
quence. Then retighten the wheel
Information nuts in order shown in the illus-
DOWN
Warning
Never use snow tires and nor-
mal tires together on your
vehicle. Tires with different
specifications and properties
10 tires
Information
According to FMCSA 393.47
standard, a commercial motor
vehicle shall not be operated if
the brake lining/pad thickness
is less than 3.2 mm (1/8 inch).
ABS warning lamp does not switch Parking brake prevents the vehicle
off in case of ABS malfunction dur- from moving after it has stopped.
ing travel. In such a case consult
authorized TEMSA Service. 1. Pull the lever upwards to activate
the parking brake.
2. Push the lever downwards to de-
activate the parking brake.
Warning
• B
raking function is adversely
affected in case of any prob-
11 brakes
lem with ABS system. Park
the vehicle in an appropri-
APPLY
ate place if ABS warning
E
BR ING
EAS
E
REL
AK
RK
TO
lamp lights up. PA
PU L
PUSH TO
•
Service brake and other “PARKING BRAKE” warning lamp
auxiliary brakes continue located on warning panel lights up
functioning even if ABS does when the parking brake is activated.
not function the result is the
Warning
It switches off when the parking Consult authorized
wheels may get locked and brake is released. TEMSA Service if the
braking distance may in-
TEMSA ‘‘PARKING BRAKE’’
crease. Release the parking brake before warning lamp does
driving and check that the ‘‘PARK- not switch off although air
ING BRAKE’’ warning lamp is off. pressure in the system is suf-
Consult ficient.
Authorized
TEMSA Service
Consult authorized TEMSA Warning
Service before continuing to Never use the parking brake
drive. during travel except for emer-
gencies.
Consult
Authorized
11 brakes
11 brakes
wear of brake pads and tires. continuously when coolant
temperature decreases. If Information
Using the retarder brake system warning lamp keeps flashing When the retarder sys-
while driving increases the life span there may be a failure in the R tem is activated, the
of the b
rake pads. system. Consult authorized retarder warning lamp
TEMSA Service before driving. located on the warning panel
Retarder brake has five levels, the lights up.
appropriate level can be applied ac-
cording to the speed of the vehicle
and road conditions. First level pro-
vides lowest braking power while
the third level provides the highest
braking power.
ASR system regulates the drive There are three control positions of
torque and the wheels are spinning The effect of the service brake in- the service brake for the intarder
independently from each other. ASR creases and life span of the brake system.
DISABLE
pads increases.
ASR system prevents wheel slip and 1st Level: Low intarder braking
provides safer driving in difficult Intarder brake system is activated power
driving conditions. or deactivated by the “INTARDER” 2nd Level: Full intarder braking
button located on the left control power
panel. 3rd Level: Service brake
Press “ASR Disable” switch located
on left control panel to deactivate
Warning ASR system.
Visual
• Deactivate ASR system while
Inspection
Check “STOP” warn-
using snow chains.
ing lamp and temperature
• Wheels may spin and the
indicator regularly while using
vehicle may sway when the
the intarder system.
ASR system is deactivated.
• The ASR warning lamp may
switch on during driving on
slippery roads, if so, reduce
speed.
11 brakes
ENGINE BRAKE
left control panel to activate the en- ON/OFF
Activate the main battery cut-off Turn the switch in the direction of The Batteries are located on the The following instructions will in-
switch to disconnect the electri- the arrow to disconnect the system left-hand side of the vehicle. crease the service life of your bat-
cal system from the battery if the from the battery. tery.
vehicle is to remain unused for a
long period of time or before re- • Battery main switch should be
pair work. turned off if the vehicle is going
to be parked for a long term.
12 electrıcal
Save the
Environment
Battery disposal should
be done according to the haz-
ardous waste disposal regula-
tions.
Warning
Warning Never activate the main bat-
After turning off the ignition tery cut-off switch while the
switch, wait for at least 2 min- engine, preheater, air condi-
utes before switching off the tioner or any electric system is
main switch.Otherwise, some running. In such a case electric
of the systems in your vehicle or control systems and alterna-
could be damaged. tor may be damaged.
12 electrıcal
Check that both vehicles operate
systems
at the same operating voltage and
the poles of the batteries are not
corroded.
Warning
• S top the engine and shift
into “Neutral” before per-
forming jump start.
• Deactivate the main battery
cut-off switch before con-
necting the jumper cables
to prevent the electric or
control systems being dam-
aged.
• If vehicles operating differ-
ent voltage, both vehicles
can be damaged.
Activate the main battery cut-off • Keep fire, sparks, naked Warning
systems
switch. Start the engine of the do- flames and cigarette away Always check the ampere val-
nor vehicle. Switch the ignition key from the battery. ue on the spare fuse and use
of the receiver vehicle to position • Connect the jumper cables a fuse that complies with the
“2”. to the battery terminals amperes written on the fuse
only. Never connect them label.
Stop the donor vehicle when the to the starter or frame.
receiver vehicle starts operating • It may not be a simple bat-
properly. tery fault if the engine does
not run. Stop the engine Consult
of the donor vehicle. Oth- Authorized
Remove the terminal clamps in re-
erwise donor battery may
TEMSA Service
verse order.
discharge. Consult authorized TEMSA Ser-
vice for relay malfunctions.
12 electrıcal
lights off when the hatch is mentation.
systems
closed. When the igntition is
Consult
off, illumination lamp lights Before replacing fuses make sure
Authorized
up for an hour if the hatch is the corresponding electric systems TEMSA Service
kept open. Close the hatch are switched off.
Consult authorized TEMSA Ser-
and then open or switch the
vice for spare fuse ordering.
igniton to “ON” to illuminate
the switch panel again.
Information
Remove the screws on cover
to access to the fuse box.
Information
Fuse panels vary depending on
Warning the customer requirements.
• Take the ampere values into Therefore, fuse panels sup-
consideration before replac- plied on the vehicle may differ
ing fuses. from those indicated in User’s
• Both faulty and replaced Manual.
spare fuses must have the
same ampere values.
12 electrıcal
button in the center, and the but-
systems
ton will be popped out. The button
on a breaker that is not tripped will
be almost flush with the surface. A
tripped button will stick out about Push the button in until it clicks into
a quarter of an inch. place.
13 maintenance
ing contact with metal surfaces and in the oil indicate that the oil has • Engine at idle,
oil by using transmission control
protects the engine. Engine oil gets deteriorated. For exact results, the • Neutral gear selected
panel.
dirty as long as the engine runs. oil must be subject to physical and • Zero output speed
chemical analysis at the laboratory. • Transmission sump oil must be
within an operating tempera-
ture band: 62ºC - 104ºC (140ºF
- 220ºF)
Warning
If oil colour is dark or black, Warning
once the first four conditions are
consult authorized TEMSA ser- Oil replacement must
met, and a 2 minute “waiting” pe-
vice immediately. always be performed
TEMSA by authorized TEMSA riod has passed (to facilitate consis-
tent oil drain back), oil level mea-
Service, if the engine
surement will be displayed.
oil loses its properties or it is
depleted.
13 maintenance
Warning
• Ensure that the engine is
stopped and the ignition 1
key is removed or in “OFF”
position before removal Pull the filter gently towards you
of the air filter for mainte- and remove.
nance and cleaning.
• Never start the engine until
the air filter is reinstalled.
Warning
Check that filter and its ele-
ments are installed correctly 2
after maintenance work.
Visual
Inspection
Replace the air filter if Apply pressurized air to the inner
too much soot or oil has ac- parts of the filter.
cumulated on it.
Performance of the vehicle and fuel Ensure that engine is stopped be-
Consult
consumption depend on the cleanli- fore checking coolant level. Park
Authorized
Service ness of the fuel filter. Clogged fuel Warning the vehicle on level ground before
TEMSA filter reduces the performance of • N o maintenance work is ap- checking coolant level.
Consult authorized
the vehicle and increases fuel con- plied for the fuel filter. Fuel
TEMSA service to replace air
sumption. filters must be replaced by
filter.
authorized TEMSA Service at Do it yourself
13 maintenance
13 maintenance
3 Engine is started and works at idle speed.
13 maintenance
Rotating Parts Do not deactivate air condi- air conditioner vents. Dry in well
Always perform radiator main- tioner immediately after long ventilated area. Clean vents regu-
tenance when the engine is larly.
use. Run the air conditioner in Warning
stopped. Check that all parts the fan position to allow the Do not run the air conditioner
are stationary before starting humidity to escape from the during filter cleaning.
to clean the radiator. system.
Save the
Environment
Vehicles in good condi-
tions releases less amount of
particles to the environment.
The periodic maintenance
achieves an improvement of
the vehicle conditions and
protects the enviroment.
13 maintenance
Warning Warning
• N ever use corrosive sub- • U
se only water and soap to
stances or solvents such as clean seat belts. Never use
paint thinner for cleaning chemicals to clean seat
non-metal surfaces. belts.
• Cleaning of electronic parts •
Never stick any materials
must only be performed by on seat belts. Avoid cutting,
authorized TEMSA Service. painting or bending the seat
• Never use corrosive sub- belt buckles.
stances or solvents such as
paint thinner or detergent
for cleaning electronic in-
struments panel and control
switches.
• Upholstery, cloth and floor
mats can be cleaned by
brushing and using vacuum
cleaner or with soapy warm
water depending on the
level of contamination.
Pressure washing can be done on Use cold or warm water for pressure
vehicle older than 2 months. Run- washing. Depending on the manu-
ning water and gentle washing facturer, you can add 1 to 5 % wash-
Warning Warning
agents approved by Temsa can be ing agent to the water.
• New paintwork is not fully Do not use high pressure
used for this process.
hardened during the first round jet nozzles and power
months. Therefore, instead nozzles. Only use flat jet
of washing the vehicle in nozzles for pressure washing.
13 maintenance
30 cm
an automatic wash system Always keep the nozzle mov-
prefer hand wash during the ing instead of pointing. The
first 2 months. average operating pressure
• Always wash the vehicle for pressure washing should
starting from top to bottom. be 50 bars.
50 bars
25°
Petrol
Solvents
Thinner
Salting icy roads during the winter Repair any observed scratches and Prepare the vehicle for winter con-
helps vehicle tires to maintain trac- paintwork damages immediately. ditions as recommended by autho-
tion. On the other hand, accumu- Uncoated surfaces cause corrosion. rized TEMSA Service.
Warning
lation of road salt in the fenders,
• Never use additives or
luggage compartments and under Surface Protection Corrosive factors as dirt, snow and
cleaning agents comprising
body zone of the vehicle causes With a recommended bright polish- other external substances remain-
petrol, thinner or any other
corrosion. ing agent, apply wax sealing. ing on the surface for a long time
hydrocarbon based solvents.
13 maintenance
The damage caused by accidents When paint work is needed, use ma-
eg. scrathes, dents etc. increase terials according to the procedures
Information the risk of corrosion unless repaired. recommended by TEMSA Service to
Conducting necessary mainte- protect the body against corrosion.
nance on the mechanical parts
required for winter conditions Clean corrosion stains formed on
as recommended by autho- Information the rim joints and apply wax-based
13 maintenance
rized TEMSA service reduces Consult authorized TEMSA preservatives recommended by au-
the risk of corrosion. service to carry out necessary thorized TEMSA service.
repairs after accident.
Information
Wash the vehicle with plenty
of water after cleaning pro-
cess.
14 Index
Front Door................................................................................. 75,112 Fuel..............................................................................................................
DPF Regeneration.................................................................................130 Fuel Tank............................................................................ 60,118,119
Drive Mode.................................................................................................. Fuse Box...............................................................................................167
Powerful Drive Mode.......................................................................135
G
E Glove Box............................................................................................... 78
Electric Socket........................................................................................ 80
Emergency Exit............................................................................................ H
Emergency Exit Windows.................................................................. 72 Hatch................................................................................................ 60,76
Engine......................................................................................................... Horn........................................................................................................ 51
Engine Control Panel.......................................................................129
I
Escape Hatch.......................................................................................... 76
Indicator......................................................................................................
Exit Windows.......................................................................................... 72
Dust Indicator..................................................................................175
Expansion Tank.............................................................................124,176
Oil Pressure Indicator........................................................................ 43
F Temperature Indicator........................................................ 37,39,178
Filter............................................................................................................ Intarder........................................................................................... 33,160
Air Filter...................................................................128,174,175,176
K N
Key............................................................................................................... NHTSA..................................................................................................... 11
Ignition Key.............................................................................51,60,95 Nozzle.................................................................................................... 87
Kneeling-Lifting.............................................................................. 33,141
O
L Odometer............................................................................................... 37
Lamp............................................................................................................ Oil Level Sensor....................................................................................173
14 Index
Brake Lamps.....................................................................................106
P
Engine Inspection Lamps................................................................107
Parking...............................................................55,97,105,134,157,158
Front Fog Lamp...............................................................................109
Paste Wax.............................................................................................184
Luggage Compartment Lamp.........................................................108
Preheater........................................................................................ 45,164
Rear Direction Indicator Lamp........................................................107
Pressure.......................................................................................................
Upper Beam Headlamps........................................................... 51,109
Air Pressure............................................................... 44,47,48,93,158
Lavatory.......................................................................................................
Oil Pressure........................................................................................ 46
Lavatory Waste Discharge................................................................. 83
Tire Pressure...................................................................... 13,146,147
Lavatory Waste Tank.................................................................. 83,182
Propeller Shaft......................................................................................100
License Plate.........................................................................................108
Low Beam Headlamps.........................................................................108
R
Lumbar................................................................................................... 91
Radiator.......................................................................... 39,113,116,178
Refuel..................................................................................................... 98
M
Relay Panel...........................................................................................166
Maximum....................................................................................................
Replacing Air Filter...............................................................................176
Speed Limit........................................................................................ 99
Retarder Control Lever........................................................................... 53
Reverse Gear.......................................................................... 59,107,134
S W
Safety........................................................................................................... Warning.......................................................................................................
Operational Safety............................................................................... 9 Warning Panel........................................................................40,41,46
Safety Switch........................................................................................124 Wax.......................................................................................................184
Scissors................................................................................................... 74 Wheel Chocks......................................................................................... 74
Shifting.................................................................................................152 Wheel Nuts...................................................................................149,151
14 Index
Signal........................................................................................................... Window.......................................................................................................
Left Turn Signal.................................................................................. 52 Exit Window....................................................................................... 73
Right Turn Signal................................................................................ 52
Snow.............................................................................................147,148
Spare Tire.............................................................................................151
Speedometer......................................................................................... 38
Steering Wheel................................................................................. 50,92
Stopping................................................................................................. 96
Sun Visor........................................................................................... 77,79
T
Terminal Clamp....................................................................................165
Tire Pressures.................................................................... 13,86,146,147
Toilet....................................................................................49,79,81,182
Tow Hook.............................................................................................101
U
Unlocking Parking Brake......................................................................158
Temsa Global
Kısıklı Cad. Şehit Teğmen İsmail Moray Sok. T: +90 216 544 52 00
No: 2/1 34622 F: +90 216 325 60 40
Altunizade - İstanbul / Türkiye E: info@temsaglobal.com
“Value in motion” and “TEMSA” is a trading name of TEMSA Global. The TEMSA Roundel and the TEMSA word mark are registered trademarks of TEMSA
Global. The information in this publication is accurate as of its publication date. The information here in is subject to change without prior notice.
Copyright© 2011 TEMSA Global. All rights reserved.