The document contains clarification requests regarding three sets of pumps supplied by a vendor:
1. Condensate pumps - the vendor's offered pump performance does not meet specifications, and clarification is requested on materials, seal design, and adding an inducer.
2. Bearing cooling water sump pump - clarification is requested on materials, pump type, and seal configuration offered versus specifications.
3. Acid gas KOD pumps - clarification is requested on materials offered versus specifications and why the impeller diameters differ between the two pumps.
The document contains clarification requests regarding three sets of pumps supplied by a vendor:
1. Condensate pumps - the vendor's offered pump performance does not meet specifications, and clarification is requested on materials, seal design, and adding an inducer.
2. Bearing cooling water sump pump - clarification is requested on materials, pump type, and seal configuration offered versus specifications.
3. Acid gas KOD pumps - clarification is requested on materials offered versus specifications and why the impeller diameters differ between the two pumps.
The document contains clarification requests regarding three sets of pumps supplied by a vendor:
1. Condensate pumps - the vendor's offered pump performance does not meet specifications, and clarification is requested on materials, seal design, and adding an inducer.
2. Bearing cooling water sump pump - clarification is requested on materials, pump type, and seal configuration offered versus specifications.
3. Acid gas KOD pumps - clarification is requested on materials offered versus specifications and why the impeller diameters differ between the two pumps.
SUBJECT: CLARIFICATIONS ON FLOWSERVE GENERAL PURPOSE PUMPS
1. 088-P-006A/B – Condensate Pumps
As per page 3 of 7 of specification 088-SP-0910-006_A the pump differential head should be read as 9.58 kg/cm2 instead of 7.28 kg/cm2. The differential head shall be 99.8 m and pump discharge pressure shall be 9.763 kg/cm2g instead of 7.46 kg/cm2g. Vendor has offered differential head of 75.91 m against 99.8 m. The NPSHA is approximately 1.8 m. The vendor to confirm the offered pump model, pump performance curve and selected motor power is suitable for these conditions mentioned in specifications? The offered material of construction for casing and impeller is SS 316 as against Carbon Steel mentioned on page 3 of 7 of specification. And what is shaft material? Why it is deviated? What is the offered mechanical seal flushing plan? As per specification page 6 of 7 it is Plan 23. Can vendor provide some mechanical device like inducer inside pump to reduce the NPSHR requirement? If so provide optional price for inducer of this pump. 2. 088-P-010A/B – Bearing Cooling Water Sump Pump Vendor has offered material code of “ST”. Please clarify what is this material. Specification page 3 of 7 material of case/impeller both carbon steel. And what is shaft material? As per page 3 of 7 the pump type is “VS4”. Vendor to mention type of pump offered. Page 7 of 9 of offer says, Mechanical Seal configuration: Single Mechanical Gas Seal whereas per specification 088-SP-0910-010_A, no such requirement is mentioned. Please clarify. 3. 088-P-001A/B & 088-P-002A/B – Acid Gas KOD Pump/SWS Acid Gas KOD Pump Vendor has offered material code as “A-8”. Please clarify what is this material. Vendor offered A 351. Per specification 088-SP-0910-001/002_A both casing and impeller to be SS 316 and Shaft SS 316. Why impeller diameter of this pump P-002A/B is more than P-001A/B?
Gas-Engines and Producer-Gas Plants
A Practice Treatise Setting Forth the Principles of Gas-Engines and Producer Design, the Selection and Installation of an Engine, Conditions of Perfect Operation, Producer-Gas Engines and Their Possibilities, the Care of Gas-Engines and Producer-Gas Plants, with a Chapter on Volatile Hydrocarbon and Oil Engines