Professional Documents
Culture Documents
Republic of The Philippines: Engr. Jonathan C. Bulagao
Republic of The Philippines: Engr. Jonathan C. Bulagao
Republic of The Philippines: Engr. Jonathan C. Bulagao
STEEL DESIGN
University of Eastern Philippines
E12
College of Engineering
CIVIL ENGINEERING DEPARTMENT Prepared by:
University Town, Northern Samar Engr. JONATHAN C.
BULAGAO
SITUATION 1 7. Which of the following most nearly gives the
A cover plated steel beam is composed of W 410 x 100 maximum shearing stress developed?
with 300mm x 12mm cover plates at top and bottom has a. 2.44 MPa c. 4.05 MPa
a simple span of 10m. b. 3.68 MPa d. 5.55 MPa
W 410 x 100 PROBLEM 8
A = 12700 mm2
A 10 m steel wide flange beam is laterally supported.
d = 400mm
The width of the web if the beam is 700 mm and web
bf = 260 mm
thickness is 10 mm. if Fy is equal to 250 MPa, the
tw = 10 mm
allowable bending stress is:
lx = 398 x 106 mm4
a. 135 MPa c. 185 MPa
1. Find the moment of inertia of the gross section.
b. 165 MPa d. 105 MPa
a. 832,5 x 106 mm4 c. 703.6 x 106 mm4
b. 302.5 x 106 mm4 d. 520.3 x 106 mm4 PROBLEM 9
2. If the allowable flexural stress in steel is fs = 138 MPa The shear capacity V if a steel wide flange section, 600
and the beam is fully supported laterally, what additional mm deep web is 9 mm thick, is closest to: assume fy =
concentrated load “P” at the center that the said beam 200 MPa
would carry aside from the total uniform load of 7.5 a. 645 Kn c. 507 kN
kN/m that it carries. b. 413 kN d. 432 kN
a. 123.5 kN c. 159.6 kN
SITUATION 3
b. 187.3 kN d. 145.7 kN
The section below is a 6m long steel column made up of
SITUATION 2
a wide flange with 3350 mm x 10 mm thick steel plates
The welded lap joint has the following data:
welded on both sides. The properties of said WF section
Fu = 350 MPa
are as follows:
Externally applied force = T
A= 11,540 mm2
Plate thickness = 12mm
Tf= 16 mm
Plate width = 250 mm
Bf = 250 mm
3. The maximum allowable weld thickness is:
Ix= 2.66 x108 mm4
a. 9.4 c. 8.8
Iy= 0.44 x 108 mm4
b. 10.4 d. 11.4
Fy= 248 MPa
4. The allowable stress in the weld is:
a. 94.5 c. 89.25
10. Find the max. slenderness ratio about the x-axis if it
b. 105 d. 115.5
is fixed at both ends (K=0.5)
SITUATION 4 a. 22.4 c. 21.24
A simply supported beam L meters long carries a b. 33.44 d. 22.94
uniformly distributed load of 16 Kn/m over its entire 11. Find the maximum slenderness ratio about the y-axis
length and has a T cross-section. The flange is 140mm x if it is fixed at both ends but hinged and braced at mid-
20mm place and the web is 160 mm by 20 mm. span.
5. Which of the following most nearly gives the moment a. 37.1 c. 21.44
of inertia about N. A.? b. 22.44 d. 27.5
a. 10.25 x 106 mm4 c. 22.24 x 106 mm4 SITUATION 4
b. 17.23 x 106 mm4 d. 19.02 106 mm4 A steel column carries moment Mx = 11 Kn.m and My =
6. Which of the following most nearly give the value of 16.5 Kn.m and an axial load of 220 KN. The steel
L to cause a maximum flexural strength of 40 MPa? section has the following properties.
a. 1.77 m c. 3.24 m A = 7420 mm2
b. 2.82 m d. 4.00 m Ry = 50.4 mm
Sx = 693x103 mm3
1
Republic of the Philippines EVALUATION
STEEL DESIGN
University of Eastern Philippines
E12
College of Engineering
CIVIL ENGINEERING DEPARTMENT Prepared by:
University Town, Northern Samar Engr. JONATHAN C.
Sy = 186x103 mm3 tw = 19.4 mm BULAGAO
K = 1.0 lx = 503.64 (106)
Fy = 400 MPa Sx = 10.88 (106)
E = 200000 MPa Ly = 156.09 (106)
Fx = 108 mm Sy = 1.014 (106)
Cm = 0.85 K = 0.50
Axial compressive stress that would be permitted if axial Cm = 0.85
force alone existed Fn = 72.54 MPa. Compressive 15. What is the eccentric moment (Mx) in KN-m?
bending stress that would be permitted if bending a. 100 c. 175
moment along the x-axis alone existed Fbx = 240 MPa b. 150 d. 90
(0.60 Fy). Compressive bending stress that would be 16. Which of the following most nearly gives the actual
permitted if bending moment along y-axis alone existed axial stress?
Fby = 300MPa (0.75 Fy). Members subjected to both a. 37.2 MPa c. 27.2 MPa
axial compression and bending stresses shall be b. 47.2 MPa d. 57.2 MPa
proportioned to satisfy the following requirements: 17. Which of the following gives the value of
slenderness ratio?
fa C m f bx C m f by a. 16.86 c. 46.86
+ + =1.0
Fa fa fa b. 26.86 d.36.86
( 1−
Fe x ' ) (
Fb x 1−
Fe y ' )
Fb y
SITUATION 6
A built-up steel I beam effectively laterally supported
12 r 2 E has a simple span of 6m. due to air conditioning
Where : Fex1 = kl 2 installation, it is necessary to provide openings as
23( ) shown. It carries a total uniform load of 175 kN/m.
rx