Professional Documents
Culture Documents
bs4 1 Specification For Hot Rolled Sections PDF
bs4 1 Specification For Hot Rolled Sections PDF
bs4 1 Specification For Hot Rolled Sections PDF
: 693.814.1
CDC ijrj~.14.01a.29-423-12~
The preparation of this British Standard was entrusted by the Iron and Steel
Standards Policy Committee (ISM/-) to Bchnical Committee ISM/13, upon
which the following bodies were represented:
BEAMA Ltd.
British Constructional Steelwork Association Ltd.
British Steel Industry
Health and Safety Executive
National Association of Steel Stockholders
0BSI 1993
Amendments issued since publication
First published November 1903
Second edition August 1921
Third edition March 1932
Amd. No. 1 Date I B x t affected
Fourth edition February 1962
Fifth edition January 1972
Sixth edition November 1980
Seventh edition December 1993
BS 4 : Part 1 : 1993
Contents
pwe
Committees responsible Inside front cover
Foreword 2
Specification
1 Scope 3
2 Normative reference 3
3 Designation 3
4 Tolerances on universal beams, columns and bearing piles 3
5 Mass and length tolerances for joists and channels 3
6 Tolerance on depth of section for joists and channels 3
7 Dimensions of hot-rolled structural steel sections 3
ables
1 Tolerances on nominal depth of joists and channels 3
2 Universal beams 4
3 Cniversal columns 7
4 Universal bearing piles 9
5 Joists with taper flanges 10
6 Structural tees cut from universal beams 11
7 Structural tees cut from universal columns 14
8 Channels 15
~~
Foreword
This Part of BS 4 has been prepared under the direction of the Iron and Steel
Standards Policy Committee and is a revision of BS 4 : Part 1 : 1980 which is
withdrawn.
The major reason for this revision is to delete the requirements for tolerances on
beams, columns and bearing piles which are now contained in BS EN 10034,
published simultaneously with this standard. The opportunity has also been
taken to delete derived properties from the tables in the previous edition of this
standard.
The dimensions and masses of beams, columns and bearing piles have also been
amended slightly to correct anomalies in tables 5 to 7 of BS 4 : Part 1 : 1980.
Compliance with a British Standard does not of itself confer immunity from
legal obligations.
- i 305 - 0.8
i
4 Tolerances on universal beams, 305 381
columns and bearing piles 381 I432 - 4.8 - 1.6
Dimensional, mass, length and straightness
tolerances on universal beams, columns ancl 7 Dimensions of hot-rolled structural
bearing piles shall be as given in BS EN 10034.
steel sections
The nominal diniensions of hot-rolled structural
steel sections shall be as given in tables 2 to 8.
Y
II
X--
t IY
Section designation Mass per Depth Width Web Hange Root radius
unit length h b S t r
kg/m mm mm mm mm inm
314 x 419 x 388 388.0 921.0 420.5 21.4 36.6 24.1
314 x 419 x 343 343.3 611.8 418.5 19.4 32.0 24.1
4
COPYRIGHT British Standards Institute on ERC Specs and Standards
Licensed by Information Handling Services
BSI B S X 4 : P A R T * 1 93 m 1 b 2 4 b b ï 0388174 121 m
BS 4 : Part 1 : 1993
6
COPYRIGHT British Standards Institute on ERC Specs and Standards
Licensed by Information Handling Services
BSI BSS4: PARTS3 93 - 3624bb9 0388376 T T 4
BS 4 : part 1 : 1993
h b l e 3. Universal columns
t I
Y
iection designation Mass per Depth Width Web Flange Root radius
unit length h b S t 'I'
kgim mm mm mm mm mm
356 x 406 x 634 633.9 474.6 424.0 47.6 77.0 15.2
356 x 406 x 551 551.0 455.6 418.5 42.1 67.5 15.2
356 x 406 x 467 467.0 436.6 412.2 35.8 58.0 15.2
356 x 406 x 393 393.0 419.0 407.0 30.6 49.2 15.2
356 x 406 x 340 339.9 406.4 403.0 26.6 42.9 15.2
I56 x 406 x 287 287.1 393.6 399.0 22.6 36.5 15.2
I56 x 406 x 235 235.1 381.0 394.8 18.4 30.2 15.2
203
203
203
x 203
x 203
x 203
x
x
x
86
71
60
86.1
71.0
60.0
222 2
e
215.8
209.6
209.1
206.4
205.8
12.7
10.0
9.4
20.5
117.3
4.2
10.2
110.2
10.2
I
203 x 203 x 52 52.0 206.2 204.3 7.9 2.5 10.2
203 x 203 x 46 46.1 203.2 203.6 7.2 1.0 10.2
8
COPYRIGHT British Standards Institute on ERC Specs and Standards
Licensed by Information Handling Services
BSI BS*4: P A R T * 1 93 m 1624669 0388178 877 m
BS 4 : Part 1 : 1993
b
r 1
I
Y
Section designation Mass per Depth Width Web Flange Root radius
unit length h b S t P
kg'm mm mm mni mm mn
i
9
COPYRIGHT British Standards Institute on ERC Specs and Standards
Licensed by Information Handling Services
BSI B S * 4 : PARTS3 93 = 362Ybb9 O388379 703
BS 4 : Part 1 : 1993
7-
Section designation Mass per Depth of Width of Thickness Radius
unit length section section
h
Web Fiange Root Toe
b S t rl r2
mm k€m mm mm mm mm mm mm
254 x 203 x 82 82.0 254.0 203.2 10.2 19.9 19.6 9.7
254 x 114 x 37 37.2 254.0 114.3 7.6 12.8 12.4 6.1
10
COPYRIGHT British Standards Institute on ERC Specs and Standards
Licensed by Information Handling Services
BSI BS*4: PART*L 9 3 W 3b24667 0388380 425 m
BS 4 : Part 1 : 1993
i
Y
Section designation ììíass per Cut from universal Width of Depth of Thickness Root
unit beam (see table 2) section section radius
length b A Y
Section designation Web Flange
S t
kg’m mni niin itun It1111 inm min
305 x 457 x 127 126.7 914 x 305 x 253 305.5 459.1 17.3 27.5 19.1
305 x 457 x 112 112.1 914 x 305 x 224 304.1 455.1 15.9 23.9 19.1
30-5x 457 x 101 100.4 914 x 305 x 201 303.3 451.4 15.1 20.2 19.1
292 x 419 x 113 113.2 838 x 292 x 226 293.8 425.4 16.1 26.8 17.8
292 x 419 x 97 96.9 838 x 292 x 194 292.4 420.3 14.7 21.7 17.8
292 x 419 x 88 87.9 838 x 292 x 176 291.7 417.4 14.0 18.8 17.8
267 x 381 x 99 98.3 762 x 267 x 197 268.0 384.8 15.6 25.4 16.5
267 x 381 x 87 86.5 762 x 267 x 173 266.7 381.0 14.3 21.6 16.5
267 x 381 x 74 73.4 762 x 267 x 147 265.2 376.9 12.8 17.5 16.5
204 x 343 x 85 88.1 686 x 254 x 170 255.8 346.4 14.5 23.7 15.2
254 x 343 x 76 76.2 686 x 254 x 152 254.5 343.7 13.2 21.0 15.2
254 x 343 i< 70 70.0 686 x 254 x 140 253.7 341.7 12.4 19.0 15.2
254 x 343 x 63 62.6 686 x 254 x 125 253.0 338.9 11.7 16.2 15.2
305 x 30.5 x 119 119.0 610 x 305 x 238 311.4 317.8 18.4 31.4 16.5
305 x 305 x 90 89.5 610 x 305 x 179 307.1 310.0 14.1 23.6 16.5
305 x 308 x 75 74.6 610 x 305 x 149 304.8 306.1 11.8 19.7 16.5
229 x 300 x 70 69.9 610 x 229 x 140 230.2 308.5 13.1 22.1 12.7
229 x 305 x 63 62.5 610 x 229 x 125 229.0 306.0 11.9 19.6 12.7
229 x 305 x 57 56.5 610 x 229 x 113 228.2 303.7 11.1 17.3 12.7
229 x 305 x 51 50.6 610 x 229 x 101 227.6 301.2 10.5 14.8 12.7
191 x 229 x 49 49.1 457 x 191 x 98 192.8 233.5 11.4 19.6 10.2
191 x 229 x 45 44.6 457 x 191 x 89 191.9 231.6 10.5 17.7 10.2
191 x 229 x 41 41.0 457 x 191 x 82 191.3 229.9 9.9 16.0 10.2
191 x 229 x 37 37.1 457 x 191 x 74 190.4 228.4 9.0 14.5 10.2
191 x 229 x 34 33.5 457 x 191 x 67 189.9 226.6 8.5 12.7 10.2
152 x 229 x 41 41.0 457 x 152 x 82 155.3 232.8 10.5 18.9 10.2
152 x 229 x 37 37.1 457 x 152 x 74 154.4 230.9 9.6 17.0 10.2
152 x 229 x 34 33.6 457 x 152 x 67 153.8 228.9 9.0 15.0 10.2
152 x 229 x 30 29.9 457 x 152 x 60 152.9 227.2 8.1 13.3 10.2
152 x 229 x 26 26.1 457 x 152 x 52 152.4 224.8 7.6 10.9 10.2
178 x 203 x 37 37.1 406 x 178 x 74 179.5 206.3 9.5 16.0 10.2
178 x 203 x 34 33.5 406 x 178 x 67 178.8 204.6 8.8 14.3 10.2
178 x 203 x 30 30.0 406 x 178 x 60 177.9 203.1 7.9 12.8 10.2
178 x 203 x 27 27.0 406 x 178 x 54 177.7 201.2 7.7 10.9 10.2
140 x 203 x 23 23.0 406 x 140 x 46 142.2 201.5 6.8 11.2 10.2
140 x 203 x 20 19.5 406 x 140 x 39 141.8 198.9 6.4 8.6 10.2
171 x 178 x 34 33.5 356 x 171 x 67 173.2 181.6 9.1 15.7 10.2
171 x 178 x 29 28.5 356 x 171 x 57 172.2 178.9 8.1 13.0 10.2
171 x 178 x 26 25.5 356 x 171 x 51 171.5 177.4 7.4 11.5 10.2
171 x 178 x 23 22.5 356 x 171 x 45 171.1 175.6 7.0 9.7 10.2
127 x 178 x 20 19.5 356 x 127 x 39 126.0 176.6 6.6 10.7 10.2
127 x 178 x 17 16.5 356 x 127 x 33 125.4 174.4 6.0 8.5 10.2
165 x 152 x 27 27.0 305 x 165 x 54 166.9 155.1 7.9 13.7 8.9
165 x 152 x 23 23.0 305 x 165 x 46 165.7 153.2 6.7 11.8 8.9
165 x 152 x 20 30.1 305 x 165 x 40 165.0 151.6 6.0 10.2 8.9
127 x 152 x 24 24.0 305 x 127 x 48 125.3 155.4 9.0 14.0 8.9
127 x 152 x 21 20.9 305 x 127 x 42 124.3 153.5 8.0 12.1 8.9
127 x 152 x 19 18.5 305 x 127 x 37 123.4 152.1 7.1 .0.7 8.9
12
COPYRIGHT British Standards Institute on ERC Specs and Standards
Licensed by Information Handling Services
BSI B S t 4 : P A R T * 1 9 3 1624669 0388182 2T8 =
BS 4 : Part 1 : 1993
146 x 127 ic 22 21.5 254 x 146 x 43 147.3 129.7 7.2 12.7 7.6
146 x 127 x 19 18.5 254 x 146 x 37 146.4 127.9 6.3 10.9 7.6
146 x 127 x 16 15.5 254 x 146 x 31 146.1 125.6 6.0 8.6 7.6
t
102 x 127 x 14 14.1 254 x 102 x 28 102.2 130.1 6.3 10.0 7.6
102 x 127 x 13 12.6 254 x 102 x 25 101.9 128.5 6.0 8.4 7.6
102 i< 127 x 11 11.0 254 x 102 x 22 101.6 126.9 5.7 6.8 7.6
133 x 102 x 15 15.0 203 x 133 x 30 133.9 103.3 6.4 9.6 7.6
133 x 102 x 13 12.5 203 x 133 x 25 133.2 101.5 5.7 7.8 7.6
X U E 1. The nominal dimensions are based on the iniperial values.
NíXE 2. The masses per metre run are calculated from the cross-sectional area on the basis of 0.78.5 kami2 lier metre nin.
Depth of
section
Thickness Root
radius
length b A T
368 x 178 x 101 100.9 356 x 368 x 202 374.7 187.2 16.5 27.0 15.2
368 x 178 x 89 88.5 356 x 368 x 177 372.6 184.0 14.4 23.8 15.2
368 x 178 x 77 76.4 356 x 368 x 153 370.5 180.9 12.3 20.7 15.2
368 x 178 x 65 64.5 356 x 368 x 129 368.6 177.7 10.4 17.5 15.2
305 x 152 x 79 79.0 305 x 305 x 158 311.2 163.5 15.8 25.0 15.2
305 x 152 x 69 68.4 305 x 305 x 137 309.2 160.2 13.8 21.7 15.2
305 x 152 x 59 58.9 305 x 305 x 118 307.4 157.2 12.0 18.7 15.2
305 x 152 x 49 48.4 305 x 305 x 97 305.3 153.9 9.9 15.4 15.2
254 x 127 x 66 66.0 254 x 254 x 132 261.3 138.1 15.3 25.3 12.7
254 x 127 x 54 53.5 254 x 254 x 107 258.8 133.3 12.8 20.5 12.7
254 x 127 x 45 44.4 254 x 254 x 89 256.3 130.1 10.3 17.3 12.7
254 x 127 x 37 36.5 254 x 254 x 73 254.6 127.0 8.6 14.2 12.7
203 x 102 x 43 43.0 203 x 203 x 86 209.1 111.0 12.7 20.5 10.2
203 x 102 x 36 35.5 203 x 203 x 71 206.4 107.8 10.0 17.3 10.2
203 x 102 x 30 30.0 203 x 203 x 60 205.8 104.7 9.4 14.2 10.2
203 x 102 x 26 26.0 203 x 203 x 52 204.3 103.0 7.9 12.5 10.2
203 x 102 x 23 23.0 203 x 203 x 46 203.6 101.5 7.2 11.0 10.2
14
COPYRIGHT British Standards Institute on ERC Specs and Standards
Licensed by Information Handling Services
BSI B S X 4 : P A R T t L 93 = LI-24669 038BL84 070
BS 4 : Part 1 : 1993
Eble 8. Channels
+--I I1
X-- --- X
I
Y
Section designation Mass per Depth of Width of í'hickness Radius Depth
unit section section between
length h 5 fillets
d
Feb Flange Root
i t y1
kgni mm nini mn nini mni tim
432 x 102 x 6.5 65.5 431.8 101.6 12.2 16.8 15.2 4.8 362.4
881 x 102 x 55 55.0 381.0 101.6 10.4 16.3 15.2 4.8 312.4
805 x 102 x 46 46.2 304.8 101.6 10.2 14.8 15.2 4.8 239.2
805 x 89 x 42 41.8 304.8 88.9 10.2 13.7 13.7 3.2 245.4
Normative reference
BS EN 10034 : 1993
BS 4 : Part I :
1993
BSI
Linford Wood
Milton Keynes
MK14 6LE