Professional Documents
Culture Documents
Setfast Acrylic Aisle Marking Paint: Protective & Marine Coatings
Setfast Acrylic Aisle Marking Paint: Protective & Marine Coatings
Setfast Acrylic Aisle Marking Paint: Protective & Marine Coatings
TINTING
Do not tint.
APPLICATION CONDITIONS
Temperature: 50°F (10°C) minimum, 110°F (43°C)
maximum
(air, surface, and material)
At least 5°F (2.8°C) above dew point
Relative humidity: 85% maximum
ORDERING INFORMATION
Packaging: 5 gallon (18.9L) containers
Weight: White: 10.21 ± 0.2 lb/gl 1.2 kg/L
Yellow: 9.74 ± 0.2 lb/gl 1.15 kg/L
SAFETY PRECAUTIONS
Refer to the MSDS sheet before use.
Published technical data and instructions are subject to change without notice.
Contact your Sherwin-Williams representative for additional technical data and
instructions.
WARRANTY
DISCLAIMER The Sherwin-Williams Company warrants our products to be free of manufactur-
ing defects in accord with applicable Sherwin-Williams quality control procedures.
The information and recommendations set forth in this Product Data Sheet are Liability for products proven defective, if any, is limited to replacement of the defec-
based upon tests conducted by or on behalf of The Sherwin-Williams Company. tive product or the refund of the purchase price paid for the defective product as
Such information and recommendations set forth herein are subject to change and determined by Sherwin-Williams. NO OTHER WARRANTY OR GUARANTEE
pertain to the product offered at the time of publication. Consult your Sherwin- OF ANY KIND IS MADE BY SHERWIN-WILLIAMS, EXPRESSED OR IMPLIED,
Williams representative to obtain the most recent Product Data Information and STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING MER-
Application Bulletin. CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
www.sherwin-williams.com/protective
Protective SETFAST® ACRYLIC
& AISLE MARKING PAINT
Marine
Coatings TM2172
TM2173
WHITE
LEAD FREE YELLOW
Recommended Spreading Rate per coat: No reduction of material is recommended as it can affect film build,
appearance, and adhesion.
Approximately 320 lineal feet (97 meters) of standard 4"
stripe per gallon In order to avoid blockage of spray equipment, clean equipment
Wet mils (microns) 15.0 (375) before use or before periods of extended downtime.
Dry mils (microns) 6.3 (158)
~Coverage sq ft/gal (m2/L) 110 (2.7) Check adhesion by applying a test strip to determine the readiness
Theoretical coverage sq ft/gal for painting.
(m2/L) @ 1 mil / 25 microns dft 672 (16.5)
NOTE: Brush or roll application may require multiple coats to Do not paint on wet surfaces.
achieve maximum film thickness and uniformity of appearance.
Drying Schedule @ 15.0 mils wet (375 microns): Do not paint when the relative humidity is above 85%.
o o
@ 77 F/25 C
Do not paint when the temperature is below 50°F (10°C).
50% RH
To touch: 45 minutes
Cool, damp conditions will prolong the drying time.
Light traffic: 1-2 hours
Heavy traffic: 12-24 hours
Painted surfaces can become slippery when wet. This aisle mark-
Full service: 2-3 days
Drying time is temperature, humidity, and film thickness dependent. ing paint is not intended to be used to paint large areas subject to
pedestrian traffic.
SAFETY PRECAUTIONS
CLEAN UP INSTRUCTIONS Refer to the MSDS sheet before use.
Clean spills and spatters immediately with soap and warm water.
Published technical data and instructions are subject to change without notice.
Clean hands and tools immediately after use with soap and warm
Contact your Sherwin-Williams representative for additional technical data and
water. After cleaning, flush spray equipment with Mineral Spirits
instructions.
to prevent rusting of the equipment. Follow manufacturer's safety
recommendations when using Mineral Spirits.
WARRANTY
DISCLAIMER The Sherwin-Williams Company warrants our products to be free of manufacturing
defects in accord with applicable Sherwin-Williams quality control procedures.
The information and recommendations set forth in this Product Data Sheet are Liability for products proven defective, if any, is limited to replacement of the de-
based upon tests conducted by or on behalf of The Sherwin-Williams Company. fective product or the refund of the purchase price paid for the defective product
Such information and recommendations set forth herein are subject to change and as determined by Sherwin-Williams. NO OTHER WARRANTY OR GUARANTEE
pertain to the product offered at the time of publication. Consult your Sherwin- OF ANY KIND IS MADE BY SHERWIN-WILLIAMS, EXPRESSED OR IMPLIED,
Williams representative to obtain the most recent Product Data Information and STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING MER-
Application Bulletin. CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
www.sherwin-williams.com/protective