Professional Documents
Culture Documents
Nureva Wall Wm408i Installation Guide July 20181
Nureva Wall Wm408i Installation Guide July 20181
INSTALLATION GUIDE
Important
SAFETY WARNINGS
Prior to installing this product, ensure you fully read and understand the installation instructions.
Failure to do so could result in personal injury or property damage. You are responsible for
ensuring all components are properly assembled and installed using the instructions provided.
Keep this information sheet and related product manuals for future reference.
SAFETY WARNINGS
The manufacturer shall not be legally responsible for any property damage or personal injury caused by incorrect installation
of the equipment or operation outside of the user’s manual. The manufacturer shall not be liable for damage to property or
personal injuries arising out of factors beyond the manufacturer’s control.
WARNING: This projector is a Class 2 laser device. Do not stare into the projector beam. The bright light
may result in permanent eye damage.
WARNING: Never operate this equipment if it is damaged. Do not modify the parts or accessories.
Opening the projector’s case exposes you to risk of electrical shock. Do not use with parts or accessories
not recommended by the manufacturer. Contact your reseller with questions regarding replacement
parts.
WARNING: Ensure that any cables used with the equipment are properly bundled, routed, covered or
constrained if they cross the floor or pose a tripping hazard.
WARNING: Failure to provide adequate structural strength for the wall mount can result in serious
personal injury or damage to property. The anchors and wall to which this equipment is attached can
support four times the combined weight of all equipment. Ensure the wall structure is reinforced as
required before installing the equipment.
WARNING: Exceeding the wall mount’s weight capacity can result in serious personal injury or damage to
equipment. The installer is responsible for ensuring the combined weight of all components attached to
the wall mount does not exceed 33 lb. (15 kg).
WARNING: Adding additional weight to the wall mount by leaning, hanging or storing items on it can
result in serious personal injury or damage to property.
June 2018 1
Important
SAFETY WARNINGS
NOTICE: This projector is a Class 2 laser device that conforms to IEC 60825-1: 2007 and CFR 1040.10 and 1040.11.
Except for deviations to Laser Notice No.50 dated June 24 2007.
FCC NOTICE
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to
radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the device and receiver
• Connect the device into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/television technician for help
SHIELDED CABLES: All connections to other computing devices must be made using shielded cables to maintain
compliance with FCC regulations.
CAUTION: Changes or modifications not expressly approved by the manufacturer could void the user’s authority, which
is granted by the Federal Communications Commission, to operate this projector.
OPERATION CONDITIONS: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired operation
INDUSTRY CANADA STATEMENT
This Class A/B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation
June 2018 2
Table of contents
BEFORE YOU BEGIN
What’s in the box 4
3. Connection diagrams 17
June 2018 3
W - Projector plate YOU
Nureva YOUT WILL
Wall – WM408i
YOU WILLN
A
ROTCEJORP – 2 XOB
QUICK STARTNEED
YOU WILL GUIDE
T
P Nureva Wall – WM408i Q YOU WILL
Z
R NEED W
1
A - Touch panel F -EPower adaptors
- Power supply (x4) - Top end
J - Bottom end cap nuts cap screws O - ITop end caps a similar anchor
Z - Tog
M Bottom connector plate D - Wall spacersC C- Wall - CWall Ibrackets
- Washers
brackets H H - USB
- USB A-BA-B Ncable
cable - Top connector W -M M plate
Projector
- Bottom
- Bottom plate
connector
connectorJ Model
plate
plate
BB
D L- Wall spacers B I -are
Washers N United
- Top
or connector Z Z- Toggler™
plate FsnaptoMo
-D N - Top - Toggler™ snap
B - Covers ©- 2018
A - TouchGpanel RS232 B
Nureva
to 3.5mmFD- -rights
Inc. All Wall
cable
Power spacers
reserved. -©Nureva
adaptors Bottom (x4)andend
theI Inc.
- Nureva
KWashers
caps Toplogo
Icaps
end trademarks of Nureva
cap screws connector
Inc. in the plate Canada
States, and other countr
N Top connector plate E - Power supply
© 2018 D DNureva
- Wall Jspacers
-All
Bottom
- Wallspacers
Inc. end cap
rights reserved.
E -IPower
2018
-nuts
-IWashers
Nureva
Nureva
and theONureva
Washers
supply
All rights
- Toplogo
B endare
J -
reserved.
NN- Top
trademarks
Bottom
Nureva
- end
Topof
and
connectorJ Inc.plate
the
connector
Nureva
cap nuts
Nureva logo
inplate
are
the United
O - Top
trademarks
a similar anchor
States,
end
of
Canada
caps
Nureva
Model
Model
and
Inc.
BBBB
other
in the Uo
countrie
KnutsZ - Toggler™
BOX 2 – PROJECTOR GE -- RS232
Powerto supply J - LBottom endend capcaps O - Top end caps a si
M - Bottom AA or
1
Z C - Wall bracketsB - CoversH - USB A-B cable 3.5mm cableconnector - Bottom plate snaptoggle or
- HDMI cable
O Top end-caps E E- Power
- Power supply
DNureva andA-B
supply J -JBottom
- Bottom end
end cap
cap nuts
nuts OO- Top - Top end
end caps
caps
Model L G
BB Canada and other countries.
a asimilar
similar
H
anchor
ancho
© 2018 Nureva Inc.I All
D - Wall spacers rights reserved.
- Washers the N - Toplogo
Nureva connector
are trademarks
M plate KNureva
of Nureva Inc. in the United
-reserved.
Bottom connector theplate
States,
P C©H2018- USB
C - Wall brackets cable
© 2018 Nureva
rightsInc. All rights andlogo Nureva ZNureva
- Toggler™ snaptoggle A
Nureva Inc. All reserved. Nureva
C and the Nureva are or logo areoftrademarks
trademarks Inc.ofinNureva
the Inc. inStates,
United the United
CanadaSta
M L
-- Warranty and warnings documents
BOX 2 – PROJECTOR DNureva YOU WILL NEED Model BB
1
J -©Bottom
E - Power supplyD - Wall spacers 2018 endInc.
Nureva cap
All nuts
rights O
reserved. - Top
Nureva endand caps
the N - Top connector plate
Nureva logo are trademarks of a similar
Nureva Inc.anchor
in the United States, Canada and other count
© 2018 I - Washers
Inc. All rights reserved. Nureva and the Nureva logo are trademarks of Nureva Inc. in the United
or
States,
I GCanada and other
J
cou
E - Power supply J - Bottom end cap nuts O - Top end Mcaps O a similar anchor
E C N
© 2018 Nureva Inc. All rights reserved. Nureva and the Nureva logo are trademarks of Nureva Inc. in the United States, Canada and other countries.
K
BOX 2 – PROJECTOR P
1S
D O I L
© 2018 Nureva Inc. All rights reserved. Nureva and the Nureva logo are trademarksN
P B
of Nureva Inc. in the United States, Canada and other countries.
F
Z
M AA
Box 2:A -Projector
Touch panel F - Power adaptors (x4) K - Top end cap screws
K O
N
P H G B - Covers
A - Touch panel G - RS232
F - Power to 3.5mm
adaptors DK - TopL end
(x4) cable - Bottom end caps
cap screws
Wall – WM408i
CB - Covers
C - Wall brackets H - USB
G - RS232 A-B cable
to 3.5mm cable M - Bottom
L - Bottom connector plate
end caps ZM-end
Toggler™ sn
P Interactive projector J I
Q D -brackets
C - Wall Wall spacersR I - A-B
H - USB S
Washers
cable
A - Touch panel
B - Covers M - Bottom
F - Power adaptors (x4)
N - Top connector
G -connector
RS232 plate
to 3.5mm
K - Top
platecable L - Bottom
Z - Toggler™end
cap scre
Model BB
caps
snaptog
or
START GUIDE
K D - Wall I - Washers plate
L Q D E R
E - Power supply
D - Wall spacers
J - Bottom end cap nuts
I - Washers
O - Top end caps
or
N - Top connector pl
a similar anchor
R Country-specific power cable S
WM408i
M
S
E and
- Power J - Bottom O - Top
QUICK STARTtemplate
GUIDE
© 2018 Nureva Inc. All rights reserved. Nureva the Nureva
supplylogo are trademarks of Nureva
endInc.
capinnuts
the United States, Canada
end and other
caps
R
A - Touch panel F - Power adaptors (x4) K - Top end
S Installation O
08i
© 2018 Nureva Inc. All rights reserved. Nureva and©the Nureva logo
Inc.are
All trademarks of Nureva
NurevaInc.
andinthe
theNureva
Unitedlogo
States,
are Canada and of
other countri
B
R QP
2018 Nureva rights reserved. trademarks Nureva Inc.
N
F B - Covers G - RS232 to 3.5mm cable L - Bottom e
Q swercs paand
-- Warranty, warnings, Quick start
P - Projector Q - Projector remote control R - Power cable M - Bottom
NEL Q R C- Power
- Wall brackets H - USB A-B cable
GUIDE
guide, installation drawing c dne poT - K )4x( srotpada rewoP - F
P - Projector lenap hcuoT - A
Q - Projector remote control cable
– TOUCH PANEL outline drawing documents
spac dne mottoB - L elbac mm5.3 ot 232SR - G srevoC - B D - Wall spacers R I - Washers N - Top conn
P - Projector Q - ProjectorBOX
remote3control
– WALL
Box 3:MOUNT
RWallI mount
- Power cable J 81¼”
BOX
P - Projector 3 – WALL MOUNT
Q - Projector remote control R - Power cable
.seirtnuoc rehto dna adanaC ,setatS detinU eht ni .cnI averuN fo skramedart era ogol averuN eht dna averuN .devreser sthgir llA .cnI averuN 8102 ©
(206.4 cm)
S - Installation template
T Wall mount K
S - Installation
D template U L V W
U Wall mount covers
M U V
V Wall plate
BOX 3 – WALL MOUNT 81¼”
W Projector plate TT O 1.2
(206.4 cm)
X Mount end-cap BOX 3 – WALL MOUNT
W
V
N
X
U
Y X
1.2
T U
Y Screws to attach plate to projector
A - Touch panel
(x4) and screws to attach projector F - Power adaptors (x4) K - Top end cap screws
to mount (x4). WV cable X Y
-- Warranty and warnings documents
B - Covers
T - Projector wall
L - Bottom end caps
G - RS232 to 3.5mm
U - Wall mount cover (L/R) Y
V - Wall mount plate U 1.2 V
mount M - Bottom connector plate
T C - Wall brackets H - USB A-B cable
X - Adjustment cover
Z - Toggler™ snaptoggle
Y - Screws to attach plate to BB
AA - HDMI cable
D - Wall spacers W - Projector
I - Washers N - Top connector plate Model
W plate
X projector and screws or
to
Y
caps(L/R) attach projector toamount
1
E - Power supply
T - Projector Bottom end capUnuts
J - wall - Wall mount cover
O - Top end V - Wall mount plate
similar anchor
June 2018 4
mount
T
© 2018 Nureva Inc. All rights reserved. Nureva and the Nureva logo are trademarks of Nureva Inc. in the United States, Canada and other countries.
X - Adjustment cover Y - Screws to attach plate to
T - Projector wall W -cover
U - Wall mount Projector YOU WILL NEED
(L/R) plate
V - Wall mount plate projector and screws to
MOUNT 81¼”
(206.4 cm)
U V
TOOLS
EED
Hardware CABLES and CONNECTIONS
Z AA
S HDMI cable
Step ladder
x1 x2 x3
2 x1 x1 x1
Z
PC must meet the following
specifications:
•
•
Windows® 10 or higher
Intel® i5 or equivalent
• HDMI video out port or adapter
• Supports 1920 x 1080 display
Laser level EN Install according to manufacturer instructions
resolution
• 4GB+FRRAMInstallez conformément aux instructions du fabricant
• 2GB+ESfree storage
8mm Instalar según las instrucciones del fabricante
10mm
• 1 GB video memory (per projector)
CS Instalaci je nutné provést v souladu s pokyny výrobce POWER REQUIREMENTS
Single Double
DA Installer i henhold til producentens instruktioner Triple
system system system
NL Installeren volgens de instructies van de fabrikant
x1 x1 x1
Screw driver
V
DE Bitte gemäß den Herstellerangaben montieren
x3 Power outlet
IT Effettua l'installazione seguendo le istruzioni del
produttore x5 x7 110-240 V
NO Installer etter produsentens anvisninger
e AA - HDMI cable
Z RU Установите
Wireless keyboardсогласно инструкциям производителя
and mouse
Stud finder
SV Installera enligt tillverkarens instruktioner
Page 1 of 4 101402-02
Toggler™ snaptoggle
x14 x28 x42 Model BB
or
10 mm wrench
Min. #10 or M5
Screws
#2 Phillips *Optional for wood
screwdriver
studs. May require
washers.
Pencil
Tape
Level
June 2018 5
1. Determine the installation location
Ensure the area you select to install your system meets the following
requirements and recommendations.
Space requirements
75 lb.
(34 kg)
*Touch panel weight
June 2018 6
2. Install the system
2.1 Install the projector wall mount plate(s)
45.85in 89.21in 43.52in
2.1.1
1165mm 2266mm 1106mm
1.12in
29mm
436mm
17.15in
PROJECTOR MOUNTING PLATE
NPT-1 WALL BRACKETS
2475mm REF
51.34in
2591mm
97.42in
2039mm
80.28in
2
installation drawing for your
3
44.69in
45.85in
IMAGE CENTER IMAGE CENTER
89.21in
systemʼs configuration from43.52in
1135mm 1165mm 2266mm 1106mm
www.nureva.com/support
755mm
29.72in
89.29in
2268mm
1 SYSTEM CENTER
178.58in
4536mm
1.12in
29mm
436mm
17.15in
PROJECTOR MOUNTING PLATE
NPT-1 WALL BRACKETS
2.1.2
1304mm
2475mm REF
51.34in
2591mm
102.00in
97.42in
2039mm
80.28in
Measure and mark the system
centerline (if installing a dual or 2
triple system).
3
44.69in IMAGE CENTER IMAGE CENTER
1135mm
Refer to installation
755mm
29.72in
1
89.29in
2268mm measurement 1 on your
installation drawing.
SYSTEM CENTER
178.58in
4536mm
1.12in
29mm
436mm
17.15in
2.1.3
PROJECTOR MOUNTING PLATE
NPT-1 WALL BRACKETS
2475mm REF
51.34in
2591mm
102.00in
97.42in
xx
3
44.69in IMAGE CENTER IMAGE CENTER
1135mm
Refer to installation
755mm
29.72in
measurement 2 on your
89.29in
2268mm
1 SYSTEM CENTER
178.58in
4536mm installation drawing.
June 2018 7
1165mm 2266mm 1106mm
S 1.12in
29mm
436mm
17.15in
R NPT-1 WALL BRACKETS
PROJECTOR MOUNTING PLATE
Q
2.1.4 MIN 254mm [10in]
MAX 660mm [26in]
MIN 254mm [10in]
MAX 660mm [26in]
4
ble
R - Power ca
r rem ote control
1304mm
2475mm REF
51.34in
Q - Projecto
2591mm
102.00in
97.42in
r
P - Projecto
81¼” the system center,
From
2039mm
n template
80.28in
(206.4 cm)
S - Installatio measure and mark the image
2
xx
center for each touch panel
LL MOUNT location.
BOX 3 – WA
3
44.69in IMAGE CENTER IMAGE CENTER
1135mm
V
755mm
29.72in
89.29in
U
2268mm
Refer to installation
min 3 ½”
1 SYSTEM CENTER
measurement 3 on your
1.2
178.58in
(8.9 cm)
4536mm
installation drawing.
PROJEC
* VARIES WITH PROJECTED IMAGE
Y
T X
W PROJECTOR
nt plate
V - Wall mou
ver (L/R)
U-W all mount co ate to
r wall to attach pl to
T - Projecto Y - Screws d screws
ver to r an
mount X - Ad justment co proj ec
ector to mou
nt
attach proj
TER
2.1.5ector plate
IMAGE CEN
W - Proj
SYSTEM /
MIN 3 ½"
1
4
to ceiling
NEED
YOU WILL 2266mm [89 1/4"]
TO NEXT PROJECTOR
REFERENCE HOLE
2266mm [89 1/4"]
TO NEXT PROJECTOR
REFERENCE HOLE
2591mm [102"] MINIMUM CEILING HEIGHT S
WM408i NUREVA WALL
INSTALLATION TEMPLATE
AA
PROJECTOR MOUNTING PLATE
THIS TEMPLATE
WALL BRACKET/SPACER
2
NUREVA WALL NTP-1
BRACKET DISTANCE
FROM CENTERLINE
MIN: 254mm [10"]
MAX: 660mm [26"]
BOARD MOUNTING
BRACKETS HOLES
1
2064mm [81 4"] template.
SYSTEM / IMAGE CENTER
TO FLOOR
SYSTEM / IMAGE CENTER
Image center
F line
H
8mm
2.1.6 10mm
J 2266mm [89 1/4"] 2266mm [89 1/4"]
2591mm [102"] MINIMUM CEILING HEIGHT
UREVA WALL
ON TEMPLATE
L V
Drill out the projector wall plate
PROJECTOR MOUNTING PLATE
e L - Bo Z - Toggler™
plate
THIS TEMPLATE
conn tor
ec
Model BB
M - Bottom
WALL BRACKET/SPACER
or Page 1 of 4
ector plate chor
N - Top conn BRACKET DISTANCE
FROM CENTERLINE
MIN: 254mm [10"]
a similar an
BOARD MOUNTING
caps
MAX: 660mm [26"]
BRACKETS HOLES
O - Top end
1
2064mm [81 4"]
s untries.
SYSTEM / IMAGE CENTER
d other co
TO FLOOR
, Canada an
the Un ited States
Nureva Inc. in
demarks of
ogo are tra June 2018 8
YSTEM / IMAGE CENTER
2.1.7 Ensure the wall mount plate is
level.
2.2.1
2.2.2
June 2018 9
2.2.3
2.2.4
2.2.5
projector.
AC Power
Network
VGA 1
1 HDMI 2
WiFi / USB
Media
HDMI
June 2018 10
2.3 Install the touch panel
Refer to installation
measurement on your
installation drawing.
2.3.2
V
2.3.3
Make sure that the RS232 to
R 3.5mm cord is out of the way
from where the touch panel
G
will be mounted.
June 2018 11
2.3.4
With the help of one other
person, lift the touch panel up
and angle it to hook onto the
wall brackets.
”¼1 R
6.1
2.3.5 )mc
8 elba
c re
woP
”½ 3 4.60 -R
2(
)mc nim Q
lortn
oc e
tom
9.8(
ETAL
PG
NITN
UOM er ro
i804
ROT
CEJ tcejo
rP -
3 ORP
61
Q
ETA
rotc
LP G
etal ejor
ROT
E
CEJ
ORP
pme
3
2.1
P-P
t no
V T N
feet land on the wall
UOM – there I - S
itall
atsn
Y
CE
AM G
I/
X
ME
X
TSY
S
etal
p tn
ot e uom
ta llaW
1
ot s lp hcat -V W
T
4
tnuo wercs ta ot
Z
)R/L
6.2
S
mo
t rot
dna swer
cejo
rotc cS - Y
e
rp h jorp
catt
a
( rev
revo
oc t
c tn
nuo
emt
m ll
aW
-U
sujd llaw
utca A-X rotc
fun ejo
tnuo rP - T
am
ni x
u
ot g
nidr
6.3 etal m
a tn occa
p ro
tcejo
emé rP -
noic mro llats W
curt fnoc nI N 6.1
v ts
sni
sal n zella E DEE
évo úge tsnI NL
rp é s ra 2.3.6 LIW
2
RF
dor ntu lats
nI S AA UOY
p lit
dloh
n ej
icala E Z
ni e neh tsnI
d sn i rel SC Z
eglo lats
tsre v nI A
H ne 74lb. nerella
d ßäkg
33.6 tsnI
D Slide the touch panel on the
noiz meg LN
alla
tsni e ttiB wall brackets until it's out of
'l au ED
orp
erot tteffE
tudo TI
the way to drill the marked
rett
гос
e re
llats
r p location.
ети nI O
вон N
giln атсУ
e ar mm
ella
tsnI
UR
mm 8
Insert a recommended wall
C VS 01
Page 2 of 4 V 101402-02 anchor at each drilled location.
E
F
8 K
8.1
2.3.8
7.1 10
7 N
7.1 10
Use a screwdriver to lever the
touch panels closer together.
G
Tighten the nuts.
J
M
J
M
9
8.1
K
8
2.3.9
8.1
N K
I
9
I June 2018 13
E
© 2018 Nureva Inc. All rights reserved. Nureva and the Nureva logo are trademarks of Nureva Inc. in the United States, Canada and other countries.
M
2.3.10 8.1
K 7 7.1 10
Use a screwdriver
G
to lever the
M
J touch panels closer together.
8 K
8.1
2.3.119
H
H
Secure the bottom of the panel E
AA
X
© 2018 Nureva Inc. All rights reserved. Nureva and the Nureva logo are trademarks of Nureva Inc. in the United States, Canada and other countries.
F
Page 3 of 4
6.1
2.4.1
AA
RS232
3.5mm
Connect the RS232 to 3.5mm
cable from the projector to
the touch panel.
are trademarks of Nureva Inc. in the United States, Canada and other countries. Repeat for
Page 3 of 4each touch panel.
C
6.2
6.3
June 2018 14
Z
2.4.2 5V DC
2A
10
Daisy chain the boards
USB A together by connecting the
USB A-B cord to the ports on
G G
USB B
the control module of one
6 touch panel to the next.
6.1
2.4.3
6.2
AA
6.3
6.1
Page 3 of 4 101402-02
2.4.4
Attach
Z
the appropriate power
adapter (F) to the 5 V power
74lb.
33.6 kg
supply (E).
Lower Upper
power
power Connect the power cable from
an outlet to either the upper or
lower power connection.
6.3
Z
X J
6.2 B
6.3
www.nureva.com/support
12.1
Z 13
6.1
2.4.6 Span N
software M
74lb.
12
33.6 kg
K
Secure the top end caps
Focus in place using the screws
provided.
13.2 13.3
Page 2 of 4 101402-02
6.2
6.3
2.4.7 Z
B
System matching Image alignme
74lb.
33.6 kg
www.nureva.com/support
13.1
© 2018 Nureva Inc. All rights reserved. Nureva and the Nureva logo are trademarks of Nureva Inc. in the United States, Canada and other countries. Page 4 of 4
13 Span Nureva
Page 2 of 4 101402-02
software Manager
13.3 13.4
June 2018 16
3. Connection
10
diagrams
7.1
6
T G G
Legend HDMI USB A-B RS232 3.5mm
J X
Y
3.1 Single system
8.1
Y
K
W
6.1
RS232 to 3.5mm
C E
AA
H
I F
D
E
6.2
F
6.3
7.1 10
6 6 Z
AA G G
T
J X
X M 74lb.
33.6 kg
R
Y Page 3 of 4 101402-02
G 8.1
K Y
N W
es, Canada and other countries. 6.1 Page 2 of 4 6.1 101402-02
E
C C AA
H
I F
D
E
6.2 6.2
F
6.3 6.3
AA Z Z
74lb.
33.6 kg
74lb.
33.6 kg
June 2018 17
ureva and the Nureva logo are trademarks of Nureva Inc. in the United States, Canada and other countries. Page 3 of 4 101402-02
G G
J
M
N Y Y
R R
U
G G
Y Y
W W
6.1 6.1 6.1
4 H
E
AA
H
C C
I F
D Z E D
Z Z Z
AA
74lb. 74lb. 74lb.
33.6 kg 33.6 kg 33.6 kg
d. Nureva and the Nureva logo are trademarks of Nureva Inc. in the United States, Canada and other countries. Page 3 of 4 101402-02
A
Page 2 Inc.
and the Nureva logo are trademarks of Nureva of 4 in the United States, Canada and other
©countries. Page 2Inc.
2018 Nureva Inc. All rights reserved. Nureva and the Nureva logo are trademarks of Nureva of 4in the United States, Canada and other countries. 101402-02 Page 2 of 4 101402-02 10140
June 2018 18
4. Initial adjustment of the projected image(s)
4.1.1
4.1.2
Image size
IMAGE SIZE
IMAGE
Pitch/Roll/Yaw
ADJUSTMENT
June 2018 19
100"
6 6
T
X X
Y
R
G
4.1.3
Y
W
6.1 6.1
Align the image to the touch
P
panel.
D
Ideally, align the image hairline
to the touch panel bezel.
6.2 6.2
6.3 6.3
Z Z
74lb. 74lb.
33.6 kg 33.6 kg
4.1.4
Page 2Inc.
rved. Nureva and the Nureva logo are trademarks of Nureva of 4in the United States, Canada and other countries. Page 2 of 4 101402-02 101402-02
4.1.5
June 2018 20
5. Adjust the projected image and touch
5.1 Download software
5.1.1
5.2.1
13.1
Nureva
Manager Open the Nureva Room
Manager on the left board.
13.4
@ support@nureva.com
101402-02
June 2018 21
13.4
12 5.2.3
Span Nureva
software Manager
5.2.4
5.3.1
Image alignment Touch calibration
13.4
@ support@nureva.com
Launch Span Workspace.
101402-02
1:41 PM
5/11/2018
6.2
6.3
*The HDL300 system cannot be mounted beneath the projector wall mount and maintain optimal performance.
June 2018 23
Troubleshooting
For troubleshooting, please see our Customer support portal.
ww.nureva.com/support
June 2018 24