Professional Documents
Culture Documents
Engine Oil and Filter - Change: Operation and Maintenance Manual
Engine Oil and Filter - Change: Operation and Maintenance Manual
Previous Screen
Welcome: cr120rxe1
Product: EXCAVATOR
Model: 349D2 L EXCAVATOR TAH
Configuration: 349D2 & 349D2 L Excavators TAH00001-UP (MACHINE)
POWERED BY C13 Engine
i02788014
Park the machine on a level surface and engage the parking brake. Stop the engine.
Note: Drain the crankcase while the oil is warm. This allows waste particles that are suspended in the oil to
drain. As the oil cools, the waste particles will settle to the bottom of the crankcase. The particles will not be
removed by draining the oil and the particles will recirculate in the engine lubrication system with the new
oil.
Illustration 1 g00101627
The crankcase drain valve is located under the rear of the upper structure.
1. Remove the bolts and the washers. Open the crankcase drain valve access cover.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 1/5
13/9/2019 349D2 & 349D2 L Excavators TAH00001-UP (MACHINE) POWERED BY C13 Engine(SEBP7439 - 28) - Documentation
Illustration 2 g01098172
Note: Refer to Operation and Maintenance Manual, "General Hazard Information" for information that
pertains to containing fluid spillage.
2. Open the crankcase drain valve. Allow the oil to drain into a suitable container.
Illustration 3 g01129934
5. Remove the oil filter with a strap type wrench. See Operation and Maintenance Manual, "Oil Filter -
Inspect".
6. Clean the filter housing base. Make sure that all of the old filter gasket is removed.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 2/5
13/9/2019 349D2 & 349D2 L Excavators TAH00001-UP (MACHINE) POWERED BY C13 Engine(SEBP7439 - 28) - Documentation
Illustration 4 g00101634
7. Apply a thin coat of engine oil to the gasket of the new filter.
Instructions for the installation of the filter are printed on the side of each Caterpillar spin-on filter. For
non-Caterpillar filters, refer to the installation instructions that are provided by the supplier of the
filter.
Illustration 5 g00278210
12. Unlatch the engine hood and raise the engine hood.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 3/5
13/9/2019 349D2 & 349D2 L Excavators TAH00001-UP (MACHINE) POWERED BY C13 Engine(SEBP7439 - 28) - Documentation
Illustration 6 g01097911
(1) Dipstick
(2) Oil filler plug
13. Remove oil filler plug (2). Fill the crankcase with new oil. See Operation and Maintenance Manual,
"Capacities (Refill)". Clean the oil filler plug and install the oil filler plug.
NOTICE
Do not under fill or overfill engine crankcase with oil. Either condition
can cause engine damage.
14. Start the engine and allow the oil to warm. Check the engine for leaks. Stop the engine.
15. Wait for fifteen minutes so that the oil can drain back into the crankcase, before you check the oil.
Illustration 7 g00832222
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 4/5
13/9/2019 349D2 & 349D2 L Excavators TAH00001-UP (MACHINE) POWERED BY C13 Engine(SEBP7439 - 28) - Documentation
16. Remove dipstick (1). Maintain the oil between the marks on the "ENGINE STOPPED" side of the
dipstick.
17. Close the engine hood and latch the engine hood.
Copyright 1993 - 2019 Caterpillar Inc. Fri Sep 13 2019 15:01:27 GMT+0200 (hora de verano de Europa central)
All Rights Reserved.
cr120rxe1
Private Network For SIS Licensees.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 5/5