Professional Documents
Culture Documents
Strength of Materials QP BANK
Strength of Materials QP BANK
Strength of Materials QP BANK
30mm O
20mm O
400mm 300mm
3) The steel flat shown in figure has uniform thickness of 20mm. Under
an axial load o 80 KN, its extension is found to be 0.17mm.
Determine the Young’s Modulus of the material.
b2=40mm
P P=80KN
b1=80mm
500mm
30KN P
60KN 80KN
A B C D
A B C d
300mm
400mm
6) A steel tube of 50mm outer diameter and 10mm thick is fitted into a
copper tube of inner diameter 50mm and 10mm thick. They are
connected by using 20mm diameter pins at the ends. If the length of
compound bar is 600mm find the stresses produced in the tubes and
pins when temperature is raised by 250C.
Take: αs = 12 x 10-6/0 C, αc = 17.5 x 10-6/0 C,
5 2
Es = 2 x 10 N/mm , Ec = 1.2 x 105 N/mm2,
30mm O
L N M
RL 25KN RM
0.25m 0.6m
8) For the bar as shown in figure calculate the reaction produced by the
lower support on the bar. Take E = 200GN/m2. Find also the stresses
in the bars.
R1
L
A 1 = 110
1.2m
55KN
2.4m
A2 = 220
1.2 m m
R2
C B
x1
m 2.0m
2) Draw the B.M. S.F. diagrams for the beam shown in figure
150N−m
C B
x1
m 2.0m
BEAM
3) As shown in figure a beam AB of length 4m acted upon by the
forces and moments. Draw the B.M. and S.F. diagrams
300KN
x
150N−m
C B
x1
4.0m 2.0m
C B
x1
4.0m 2.0m
BEAM
5) Draws shear force and bending diagram for the beam shown in
figure. Locate point of Contra flexure if any.
6) A beam of span 6m has one support at the left and the other
support at a distance of 2m from the right end. The beam carries
a UDL of 10kN/m over the entire span. Draw the SFD and BMD
and prove that the middle point of the beam is the point of contra
flexure.
Cast iron
water main
WATER
500mm
25mm 25mm
1 50mm
2
150mm
50mm
100mm
30mm
30mm
200mm=d 120mm
50mm
120mm
BEAM
6) A flitched timber beam consists of two joists 100 mm wide and 300
mm deep with a steel plate 200 mm deep and 15 mm thick placed
symmetrically in between and clamped to them. Calculate
300mm
200mm
Timber Beam
1.0cm
20cm
18cm
1.0cm 12.0 cm
Flitched Beam
200mm
20mm
T=10mm
Web
340mm=d 300mm
Flange
20mm
BEAM
200mm
Flange
50mm
Web
200mm
50mm
Flange 15mm
45mm
Web
120mm 90mm
T=15mm
Flange 15mm
BEAM
15mm
200mm
300mm
100mm
Steel Section
150N−m
C
x1
4.0m 2.0m
BEAM
2) A beam AB of 4 meters span is simply supported at the ends and is
loaded as shown in figure. Determine
i) Deflection at C
ii) Maximum deflection and
iii) Slope at the end A
Given: E = 200x106 KN/m2 and I = 20x10-6 m4
x
150N−m
A B
C
x1
4.0m 2.0m
BEAM
10KN/m
A B
C D
150N−m
A B
C
4.0m 2.0m
6.0m
BEAM
10KN 10KN
D C
A B
E
1.0 m 3.0 m 1.0 m
BEAM
300KN
x
150N−m
A B
C
x1
4.0m 2.0m
BEAM
*****END*****
SOM-Question Bank -(DSK)