Professional Documents
Culture Documents
User Manual Dishwasher: Downloaded From Manuals Search Engine
User Manual Dishwasher: Downloaded From Manuals Search Engine
User Manual Dishwasher: Downloaded From Manuals Search Engine
Dishwasher
ZDF3023
Safety information
Before the installation and use of the appliance, • Use only new hoses to connect the appli-
carefully read the supplied instructions. The ance to the water supply. Do not use old ho-
manufacturer is not responsible if an incorrect ses again.
installation and use causes injuries and dam- • Before you connect the appliance to new
ages. Always keep the instructions with the ap- pipes or pipes not used for a long time, let
pliance for future reference. the water flow until it is clean.
Children and vulnerable people safety • The first time you use the appliance, make
sure that there is no leakage.
Warning! Risk of suffocation, injury or
permanent disability. Electrical connection
• Do not let persons, children included, with Warning! Risk of fire and electrical shock.
reduced physical sensory, reduced mental
functions or lack of experience and knowl- • The appliance must be earthed.
edge use the appliance. They must have su- • Make sure that the electrical information on
pervision or instruction for the operation of the rating plate agrees with the power sup-
the appliance by a person who is responsible ply. If not, contact an electrician.
for their safety. Do not let children play with • Always use a correctly installed shockproof
the appliance. socket.
• Keep all packaging away from children. • Do not use multi-plug adapters and exten-
• Keep all detergents away from children. sion cables.
• Keep children and pets away from the appli- • Make sure not to cause damage to the mains
ance door when it is open. plug and to the mains cable. Contact the
service or an electrician to change a dam-
Installation
aged mains cable.
• Remove all the packaging.
• Connect the mains plug to the mains socket
• Do not install or use a damaged appliance. only at the end of the installation. Make sure
• Do not install or use the appliance where the that there is access to the mains plug after
temperature is less than 0 °C. the installation.
• Obey the installation instruction supplied • Do not pull the mains cable to disconnect
with the appliance. the appliance. Always pull the mains plug.
Water connection • Only for UK and Ireland. The appliance
has a 13 amp mains plug. If it is necessary to
• Make sure not to cause damage to the water change the fuse in the mains plug, use a 13
hoses. amp ASTA (BS 1362) fuse.
2 www.zanussi.com
1 Worktop
1 2 Lower spray arm
3 Filters
10
4 Rating plate
9 5 Rinse aid dispenser
8 2 6 Detergent dispenser
7 7 Salt container
3
6
8 Water hardness dial
4
5 9 Upper spray arm
10 Upper basket
www.zanussi.com 3
Downloaded from www.Manualslib.com manuals search engine
Control panel
1 2 3 4
8 7 6 5
Indicators Description
Washing phase indicator.
Rinse aid indicator. This indicator is off while the programme oper-
ates.
Salt indicator. This indicator is off while the programme operates.
Multitab indicator.
Programmes
4 www.zanussi.com
For all the necessary information for test performance. send an email to:
info.test@dishwasher-production.com
Write down the product number (PNC) that is on the rating plate.
Options
Multitab function The function stays on until you deactivate
Activate this function only when you use the it. Press Multitab, the Multitab indicator
combi detergent tablets. goes off.
This function deactivates the flow of rinse aid
If you stop to use the combi detergent
and salt. The related indicators are off.
tablets, before you start to use separately
The programme duration can increase.
detergent, rinse aid and dishwasher salt,
Activating the Multitab function do these steps:
Activate or deactivate the Multitab function 1. Deactivate the Multitab function.
before the start of a programme. You can- 2. Set the water softener to the highest level.
not activate or deactivate this function while a 3. Make sure that the salt container and the
programme operates. rinse aid dispenser are full.
1. Press the on/off button to activate the appli- 4. Start the shortest programme with a rinsing
ance. phase, without detergent and without
dishes.
2. Make sure that the appliance is in setting
mode. Refer to ‘SETTING AND STARTING 5. Adjust the water softener to the water hard-
A PROGRAMME'. ness in your area.
3. Press Multitab, the Multitab indicator 6. Adjust the released quantity of rinse aid.
comes on.
www.zanussi.com 5
Downloaded from www.Manualslib.com manuals search engine
Before first use
1. Make sure that the set level of the water ble to the water hardness in your area. Refer to
softener agrees with the water hardness in the instructions on the packaging of the prod-
your area. If not, adjust the water softener. ucts.
Contact your local water authority to know
the water hardness in your area. Adjusting the water softener
2. Fill the salt container. Hard water contains a high quantity of minerals
that can cause damage to the appliance and
3. Fill the rinse aid dispenser.
bad washing results. The water softener neu-
4. Open the water tap. tralises these minerals.
5. Processing residues can stay in the appli- The dishwasher salt keeps the water softener
ance. Start a programme to remove them. clean and in good conditions. Refer to the table
Do not use detergent and do not load the to adjust the water softener to the right level. It
baskets. makes sure that the water softener uses the
correct quantity of dishwasher salt and water.
If you use the combi detergent tablets, ac-
tivate the multitab function. These tablets You must adjust the water softener man-
contain detergent, rinse aid and other added ually and electronically.
agents. Be sure that these tablets are applica-
Water softener
Water hardness
adjustment
German French mmol/l Clarke Manual Elec-
degrees degrees degrees tronic
(°dH) (°fH)
51 - 70 91 - 125 9.1 - 12.5 64 - 88 2 1) 10
43 - 50 76 - 90 7.6 - 9.0 53 - 63 2 1) 9
37 - 42 65 - 75 6.5 - 7.5 46 - 52 21) 8
29 - 36 51 - 64 5.1 - 6.4 36 - 45 21) 7
23 - 28 40 - 50 4.0 - 5.0 28 - 35 21) 6
19 - 22 33 - 39 3.3 - 3.9 23 - 27 21) 51)
15 - 18 26 - 32 2.6 - 3.2 18 - 22 1 4
11 - 14 19 - 25 1.9 - 2.5 13 - 17 1 3
4 - 10 7 - 18 0.7 - 1.8 5 - 12 1 2
<4 <7 < 0.7 <5 12) 12)
1) Factory position.
2) Do not use salt at this level.
6 www.zanussi.com
1 2
1 2
Turn the water hard-
ness dial to the posi-
tion 1 or 2.
Electronic adjustment
The appliance must be in setting mode.
Refer to ‘SETTING AND STARTING A
3 4
PROGRAMME’.
Put 1 litre of water in
1. Make sure that the programme marker on the salt container (on-
the programme knob is aligned with the off ly for the first time).
position.
2. Press and hold Start. At the same time turn
the programme knob counterclockwise until
the programme marker is aligned with the
first programme on the control panel.
3. Release Start when the display shows the
setting of the water softener.
• Example: = level 5.
4. Press Start again and again to change the 5 6
setting.
Filling the rinse aid dispenser
5. To confirm the setting, turn the programme
knob until the programme marker is aligned Caution! Only use rinse aid for
with the off position. dishwashers. Other products can cause
Filling the salt container damage to the appliance.
Caution! Only use dishwasher salt. Other The rinse aid, during the last rinsing phase,
products can cause damage to the helps to dry the dishes without streaks and
appliance. stains.
Water and salt can come out from the salt
container when you fill it. Risk of corrosion. To
prevent it, after you fill the salt container, start a
programme.
www.zanussi.com 7
Downloaded from www.Manualslib.com manuals search engine
X
MA
+
4
1
2 3
X
MA
+
4
1
2 3
3 4
Daily use
1. Open the water tap. • Do not put in the appliance items that can
2. Turn the programme knob until the pro- absorb water (sponges, household cloths).
gramme marker is aligned with a pro- • Remove remaining food from the items.
gramme on the control panel. Make sure • Make soft the remaining burned food on the
that the appliance is in setting mode. Refer items.
to ’SETTING AND STARTING A PRO- • Put hollow items (cups, glasses and pans)
GRAMME’. with the opening down.
• If the salt indicator is on, fill the salt con- • Make sure that cutlery and dishes do not
tainer. bond together. Mix spoons with other cutlery.
• If the rinse aid indicator is on, fill the rinse • Make sure that glasses do not touch other
aid dispenser. glasses.
3. Load the baskets. • Put small items in the cutlery basket.
4. Add the detergent. • Put light items in the upper basket. Make
5. Set and start the correct programme for the sure that the items do not move.
type of load and soil. • Make sure that the spray arms can move
Loading the baskets freely before you start a programme.
Refer to the supplied leaflet with examples Using the detergent
of the load of the baskets. Caution! Use only detergents for
• Only use the appliance to wash items that dishwashers.
are dishwasher-safe. Do not use more than the correct quantity
• Do not put in the appliance items made of of detergent. Refer to the instructions on
wood, horn, aluminium, pewter and copper. the detergent packaging.
8 www.zanussi.com
1 2
10 www.zanussi.com
A
5 6
Put filter (A) to its ini- Assemble filters (B)
tial position. Make and (C). Put them in-
sure that it assembles to position in filter
correctly under the (A). Turn the handle
two guides (D). clockwise until it
locks.
Troubleshooting
The appliance does not start or it stops during • - The anti-flood device is on.
operation.
Warning! Deactivate the appliance before
First try to find a solution to the problem (refer
you make the checks. Turn the programme
to the table). If not, contact the service.
knob until the programme marker is aligned
With some problems, the display shows
with the off position.
an alarm code:
• - The appliance does not fill with water.
• - The appliance does not drain the wa-
ter.
www.zanussi.com 11
Downloaded from www.Manualslib.com manuals search engine
Problem Possible cause Possible solution
The programme does not The mains plug is not connected in Connect the mains plug.
start. the mains socket.
The appliance door is open. Close the appliance door.
You did not press Start. Press Start.
The fuse in the fuse box is damaged. Replace the fuse.
The delay start is set. Cancel the delay start or wait for the
end of the countdown.
The appliance does not fill The water tap is closed. Open the water tap.
with water.
The water pressure is too low. Contact your local water authority.
The water tap is clogged or there is Clean the water tap.
limescale on it.
The filter in the water inlet hose is Clean the filter.
clogged.
The water inlet hose has a kink or a Make sure that the position of the
bend. hose is correct.
The anti-flood device is on. There are Close the water tap and contact the
water leakages in the appliance. Service.
The appliance does not The sink spigot is clogged. Clean the sink spigot.
drain the water.
The water drain hose has a kink or a Make sure that the position of the
bend. hose is correct.
After the checks are completed, turn the pro- If the problem occurs again, contact the Serv-
gramme knob until the programme marker is ice.
aligned with the programme that was in opera- If the display shows other alarm codes, contact
tion when the problem occurred. The pro- the Service.
gramme continues from the point of interrup-
tion.
The washing results and drying results are not satisfactory
12 www.zanussi.com
Activating the rinse aid dispenser with the 1. Make sure that the programme marker on
multitab function activated the programme knob is aligned with the off
position.
The appliance must be in setting mode.
2. Press and hold Start. At the same time turn
Refer to ‘SETTING AND STARTING A
the programme knob counterclockwise until
PROGRAMME’.
the programme marker is aligned with the
first programme on the control panel.
www.zanussi.com 13
Downloaded from www.Manualslib.com manuals search engine
3. Release Start when the display shows the Off
setting of the water softener.
On
4. Turn the programme knob counterclockwise
until the programme marker is aligned with 6. Press Start to change the setting.
the second washing programme on the 7. To confirm the setting, turn the programme
control panel. knob until the programme marker is aligned
5. The display shows the setting of the rinse with the off position.
aid dispenser.
Technical information
Dimensions Width / Height / Depth (mm) 600 / 850 / 610
Electrical connection Refer to the rating plate.
Voltage 220-240 V
Frequency 50 Hz
Water supply pressure Min. / max. (bar / MPa) (0.5 / 0.05 ) / (8 / 0.8 )
Water supply 1) Cold water or hot water2) max. 60 °C
Capacity Place settings 12
Power consumption Left-on mode 0.99 W
Off-mode 0.1 W
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
2) If the hot water comes from alternative sources of energy, (e.g. solar panels, aeolian energy), use the hot
water supply to decrease energy consumption.
Environment concerns
14 www.zanussi.com
3
820 mm
4
600 mm
1 4
Make sure that the dimensions of the recess
agree with the dimensions in the figure. Loosen or tighten the adjustable feet for a cor-
rect level of the appliance. With a correct level
the appliance door closes and seals correctly.
Install the appliance worktop to the appliance if
you want to use the dishwasher as a freestand-
ing appliance.
1 2 The plinth on freestanding appliance is not ad-
justable.
2 3
www.zanussi.com 15
Downloaded from www.Manualslib.com manuals search engine
156959590-A-032011
www.zanussi.com/shop