Professional Documents
Culture Documents
UNO-2.0 - 2.5-TL-OUTD-Quick Installation Guide EN-RevC
UNO-2.0 - 2.5-TL-OUTD-Quick Installation Guide EN-RevC
The labels on the inverter have the Agency marking, main technical data and identification of the equipment and manufacturer
ABB Solar inverters
UNO-2.0/2.5-I-OUTD
www.abb.com/solar MODEL: www.abb.com/solar MODEL: P/N:PPPPPPPPPPP
SOLAR INVERTER UNO-2.5-I-OUTD-X SOLAR INVERTER UNO-2.0-I-OUTD-S 04
SN:YYWWSSSSSS WK:WWYY
Vdc max 520 V Vacr 230 V 1Ø Vdc max 520 V Vacr 230 V 1Ø WO:XXXXXXX 03
Vdc MPP 90 - 520 V fr 50 Hz Vdc MPP 90 - 520 V fr 50 Hz
Vdc, Full Power 200 - 470 V Pacr (cos φ = 1) 2500 W @ 45°C amb. Vdc, Full Power 200 - 470 V Pacr (cos φ = 1) 2000 W @ 50°C amb. SO:SXXXXXXXX Q1
Idc max 12.8 A Iac max 12.5 A Idc max 12.5 A Iac max 10.5 A
Isc max 15 A Isc max 15 A
01 Inverter model
02 Inverter Part Number
IP65 IP65 03 Inverter Serial Number
-25 to +60 °C 5minutes -25 to +60 °C 5minutes
-13 to +140 °F -13 to +140 °F 04 Week/Year of manufacture
The labels attached to the equipment must NOT be removed, damaged, dirtied, hidden,etc...
If the service password is requested, the field to be used is the serial number -SN: YYWWSSSSSS-
In the manual and/or in some cases on the equipment, the danger or hazard zones are indicated with signs, labels, symbols or icons.
2.
The models of inverter to which this guide refers are available in 2 power ratings:
14 2.0 kW / 2.5 kW.
3.
Environmental checks
Choice of installation location
In addition to what is explained below, the safety and installation information provided in the Installations above 2000 metres
installation manual must be read and followed. The technical documentation and the interface On account of the rarefaction of the air (at high altitudes), particular conditions may occur:
and management software for the product are available at the website. --Less efficient cooling and therefore a greater likelihood of the device going into derating because of high internal
The device must be used in the manner described in the manual. If this is not the case the temperatures
safety devices guaranteed by the inverter might be ineffective. --Reduction in the dielectric resistance of the air that, in the presence of high operating voltages (DC input), can create
electric arcs (discharges) that can reach the point of damaging the inverter
All installations at altitudes of over 2000 metres must be assessed case by case with the ABB Service department.
6.
Installation position Components available for all models Quantity Components available for all models Quantity
--Install on a wall or strong structure suitable for bearing the weight
Choice of installation location
--Install in safe, easy to reach places Connector for connecting the configu- Two-hole gasket for M20 signal cable
2 2+2
UNO UNO UNO
--If possible, install at eye-level so that the display and status LEDs can be seen easily rable relay glands and cover
--Install at a height that considers the heaviness of the equipment
--Install vertically with a maximum inclination of +/- 5°
--To carry out maintenance of the hardware and software of the equipment, remove the covers Connector for the connection of the
2
communication and control signals
UNO UNO
UNO UNO
on the front. Check that there are the correct safety distances for the installation that will allow
UNO
TRIO-20.0-27.6-TL-O
Guida
Oltre
Rapida UTD-Quick
di installazio
a quanto Installation
sicurezza
di seguito Guide
power-one.com. ed installazione IT RevA
condizioni esposto
di garanzia riportateè obbligatorio ne
Etichette e Simboli TRIO-20.0-TL-OUTD & TRIO-27.6-TL-OUTD
nel manualeleggere
La tecnologia si intendono e rispettare
probabilmentedi di installazione
questo inoltre le informazioni
inverter valide disponibiledi
gli inverter se il Cliente
che trifasederiva dal rispetta sul sito
vogliono più utilizzatiperfezionamento quanto www.
CARATTERISTICHE realizzare descritto
al TRIO-20.0-27.6-TL-O nelmanuale.
Guida
• Convertitore mondo
impianti nonchédei modelli
15cm 15cm
Rapida
di grandi i primi AURORA
• di potenza dimensioni a conseguire
UTD-Quick
Oltre PVI-10.0
a quanto senza condensatori i migliori
di installazio
• Unità con Installation e
risultati 12.5
disicurezza
UNO UNO • orientamento in Guide che
conversione di seguito sono
power-one.com. ed installazione elettrolitici IT RevA
variabile.
sul campo
condizioni DC/AC esposto
ne
15cm 15cm
per aumentare
UNO
• Doppia
di garanzia con riportateè obbligatorio
topologianel
dell’energia
La tecnologia sezione manualeleggere ulteriormente
• Ampio si intendono di ponte e rispettare
probabilmentedianchedi ingresso inoltre di installazione
UNO UNO
trifase le informazioni la durata
• Scatolaintervallo questonel caso con valide
• gli inverter inverterdi inseguimento disponibiledi di vita
di cablaggio di tensione stringhe se il Cliente e
trifasederiva
UNO dalorientate
cheagli standard rimovibile in ingresso MPP rispetta sul sito
vogliono
• Algoritmo più utilizzati perfezionamentoin direzioniindipendente, quanto www.
03
• raccolta di MPPT impianti facilemondo
• Convertitore di energia veloce (versioni nonchédei modelli
installazione una
1. di grandi-S2, i primi AURORA ottimale
Final installation of the inverter must not compromise access to any disconnection
• una prestazione di potenza e preciso -S2F a conseguire raccolta
• Costruzione perdimensioni
l’inseguimento e -S2X) PVI-10.0
• Unità senza con
i migliori
• Possibilità costante condensatori orientamento risultati e 12.5
• di conversione
da esterno e della in che
stabile elettrolitici potenza in variabile. sono
sul campo di gestire DC/AC
• Possibilità per uso nell’intero tempo
• Doppia direttamente per aumentare reale
• Uscita conin qualsiasi intervallo e per
di connessione topologia una
sezione di tensione ulteriormente migliore
2
® ausiliaria ponte
AURORA • Ampio di ingresso la potenza in ingresso
1
anche DC di trifase ambientale
PHOTOVOLTAI • Scatolaintervallo nel(24V, sensori con esterni attiva
la durata
TRIO caso300mA) inseguimento e le regolazioni
e di potenza di vita
C INVERTER
®
N10606 • di cablaggio di tensionedi stringhe per il e
VDC
monitoraggio in uscita
VDC
max MODEL:
TRIO-20.0-TL-OUTD-XXX
Made
agli rimovibile in ingresso orientate MPP di potenza
indipendente,
MPP in Italy
standard
DIN
VDC,
• Algoritmo
V VDE0126-1-1
Full
IDC max Power
1000 PROTECTIV
in direzioni delle reattiva
internazionali per una
200 V
condizioni
ECLASS:
-
ISC max 440 950 V
diverse consente
I
- 800
2 x 25 V
VAC
raccolta di MPPT ®
facile
• AURORA
nom
2 x30 A
f nom 0
-40
di energia veloce (versioni installazione unaambientali
1.
400
A
PACnom V 3Ø
, 3W+N+PE PHOTOVOLTAI ottimale
-25to+
IP65
PACnom (cosφ= 1)
50
IAC max (cosφ= ±0.9) 22000 W Hz una TRIO e preciso -S2, raccolta
60°C
-13to+14
2000 @45 prestazione
®
-S2F
per l’inseguimento
0°F
0 W@ °Camb
45
• Costruzione
. V
C INVERTER N10606
e -S2X)Power-One
33 A °Camb.
DC
max MODEL:
• Possibilità
V DC
MPP costante TRIO-27.6-TL-OUTD-XXX DIN
Made
in Italy
V
dellaTRIO-XX.X-XX-XXXX-XXX-
Etichette e Simboli
da
DC, V VDE0126-1-1
1000
200 esterno e stabile
Full PROTECTIV
In caso
I DC
max
Power
V ECLASS: potenza
I di500 -- 800
950
in tempo
• Possibilità 2gestire perV uso nell’intero
SC max I
V
di richiesta x 32 V
AC nom
10minutes
2 x40 A direttamente
f nom
in qualsiasi 0
-40
intervallo realeXXX01
e per
della • -2Uscita A
P ACnom
400
V 3Ø
unamigliore
Sul manuale password di , 3W+N+PE
IP65connessione I
P (cos
®
5to+
-13to+1460°C
ausiliaria φ da
φ
ACnom
AC max
30000 50 Hz condizione
(cos
= 1)
display
=± 0.9)
W @45
di tensione
P/N:PPPPPPPPPPP
AURORA di servizio 0°F 2760
e/o
0
45 la . 02 in ingresso
°Camb
PHOTOVOLTAIin alcuni
DC (24V, di sensori W@ 45 A °Cambpotenza
ambientale
il campo .
attiva
Obbligo TRIO casi SN (serial 300mA) esterni el
e di potenza
SN:SSSSSSSSSS
03
C INVERTER sull’apparecchiatura,
Modelloe regolazioni
®
N10606
number) per il 01
in uscita
V DC
del manuale di consultazione monitoraggio XXXXXXXXXWK:WW/YY
di inverter di potenza
max MODEL:
V
V
DC
MPP
TRIO-20.0-TL-OUTD-XXX DIN
Made
in Italy
V VDE0126-1-1
dautilizzare 10minutes
02
Part
Number 04
reattiva Q1
DC,
1000 03
Serial delledell’inverter
PROTECTIV
le zone
Full
IP65 I DC
Power
200 V èriportato
Numbercondizioni
max ECLASS:
I SC max
Grado 440 -- 800
950
V
V Pericolo di pericolo
I
nell’etic 04
Settimana/Anno
di22 xprotezione hettaapplicata
AC nom ®
V
AURORA dell’inverterambientali
parecchiatura 25 A
x30
f
P
nom
400 tante
0
-40
generico o attenzione
A ACnom V 3Ø
PHOTOVOLTAI
informazione sullaparte di produzione
dell’ap-
P , 3W+N+PE
(cos
-25to+
60°C IP65
φ
22000 50 Hz rezza
ACnom = 1)
- Impor TRIO vengono superiore
0°FPolo
-13to+14 I (cos
(inverter)
φAC max = ±0.9)
2000 W @45 -
®
C INVERTER
positivo di sicu-
inverter to the
N10606
0 W@ °Camb
vo della MODEL: indicate
45 . V
33 A °Camb.
DC
max Power-One
e V
con
(DC) tensionepolo negati-
Made
Intervallo V segnaletica, TRIO-XX.X-XX-XXXX-XXX-
DC
DC,
MPP
TRIO-27.6-TL-OUTD-XXX DIN in Italy
V VDE0126-1-1
1000
Tensione
Full PROTECTIV
I Power
V
In caso di temperature 200
di ingresso
DC ECLASS:
max
-
500 950 V etichette,
di richiesta
- 800 V AC nom
pericolosa 0-40
Obbligo
10minutes
2 x 32 V
2 x40 A
f nom
400 simboli XXX 01
della
P V 3Ø
gliamentodi -1-2utilizzare
A
o icone.
ACnom
mento trasformatore
φ
P/N:PPPPPPPPPPP
di servizionali di
AC max =± 0.9)
e/o i 0°F l’abbi- 2760 W @45
e/o in mezzi 0 W@ °Camb
protezione 45 . 02 Parti
45 A °Camb.
alcuni il campo perso di isola calde
Obbligo casi SN (serial - -01 SN:SSSSSSSSSS
03
sull’apparecchiatura, Punto Modello
del manuale di consultazione number)
dautilizzare messadi collegamento 10minutes
02
Part Rispettivamente
di inverter XXXXXXXXXWK:WW/YY
04
a terra 03 Number continua
IP65 Grado le zone èriportato della04 Serial Numberdell’inverter Q1
Pericolo di pericolo nell’etic di protezione Settimana/Anno e alternata corrente
di protezione hettaapplicata dell’inverter
parecchiatura tante generico o attenzione Tempo
sullaparte di produzione
dell’ap- rezza informazione - Impor vengono superiore immagazzinatadi scarica
Polo (inverter)
positivo di sicu-- indicate dell’energia
vo della e con
(DC) tensionepolo negati- Intervallo
Tensione
segnaletica,
di ingresso di temperature etichette,
pericolosa
Obbligo simboli
gliamentodi utilizzare Senza o icone.
nali e/o i
di protezione mezzi l’abbi- mento trasformatore Parti
perso di isola calde
- -
Punto
messadi collegamento Rispettivamente
a terra continua
di protezione della
e alternata corrente
Tempo
di scarica
immagazzinata
dell’energia
Please refer to the warranty terms and conditions available on the website and evaluate ABB
XXXXXXX
solar
inverters
XXXXXXXXXXXXXX
50
XXXXXXXXXXXX
XXXXX
50 any possible exclusion due to improper installation. Bracket and screws for lead sealing the
cm
UNO UNO
cm 1
UNO UNO
4. 7.
LEDs and BUTTONS, in various combinations, can be used to view the status or carry out complex actions that are described more fully in the manual.
CR2032
GND_MODE MEMORY
J4
CARD
W2 BT1
WHITE 2 18
Wall/Pole mounting
11
14
1 17
Standard Version
Instruments
GFI
9
S2
J9 J10
W3
BLACK
J6 1
W4
MOV1 MOV2 GFI
5
6
RED CR2032
1 1
GND_MODE MEMORY CARD
TERM. 120
J4
J14
Assembly Instruction
W2 BT1 J16
RS485(B)
RS485(A)
1 WHITE 2
OFF
18
1 2
11
14
J7 J8 ON
J5 S1
1 17 J15 1
F1 J25 K4 S2
J9 J10
W3
BLACK J23
J13
1 OFF 1 2
1 2J7 J8
3 4 1 2 3 S1
ON
J15
N.O.
MOV4 S3
T/R
T/R
WT
WT
RTN
LNK
R
R
DC IN GRID
C
J17 J18
RS485 CARD
1 2 3
N.O.
T/R
T/R
WT
WT
RTN
LNK
R
R
DC IN GRID
C
3 x Ø 10 mm ground.
insufficient sunlight.
It is used to scroll up the menu options or to
UP
shift the numerical scale in ascending order. --Position the bracket 01 perfectly level on the wall
YELLOW The inverter has de- DC
and use it as a drilling template.
ALARM
tected an anomaly. The anomaly is AC
It is used to scroll down the menu options 09 10 11 05 08 06
LED
shown on the display. DOWN or to shift the numerical scale in descending 09 10 11 05 08 06 --Drill the 3 holes required using a drill with 10mm bit.
POWER ALARM GFI ESC UP DOWN ENTER
order. The holes must be about 70mm deep.
It can be used to conrm an action, to access -S Version --On bracket 01 there are 5 fastening holes, but only
CR2032
GND_MODE MEMORY CARD
14
1 17
14
GFI
14 12 13
9
RED
ENTER
J4 J16
RS485(B)
RS485(A)
1 W2 OFF BT1 1 2
J7 J8 WHITE 2
ON
18
S1 J15
11
14
J5 1
1 17
MOV3 MOV4 S3
12
9
J23S2
J9 J10
W3
BLACK
17 18 J6 1
W4
MOV1 MOV2 GFI
J17 J18
1
RED RS485 CARD
1
TERM. 120 J14
J24
J16
RS485(B)
RS485(A)
1 2J7 1
3 4 1 2 3 OFF 1 2
J8 ON
-IN -IN +IN +IN J5 N L S1 J15 1
N.C.
N.O.
T/R
T/R
WT
WT
RTN
LNK
R
R
DC IN GRIDMOV3 MOV4
C
S3
digit to be edited.
J19 J20 F1 J25 K4 ALARM J13 WIND REM RS485
J23
13
17 18
J17 J18
RS485 CARD
J24
1 2 3
B
-IN -IN +IN +IN N L
N.C.
N.O.
T/R
T/R
WT
WT
RTN
LNK
R
R
DC IN GRID
C
09 10 11 07 05 08 06
O
UN
The components of the packaging must be disposed on in accordance with the regulations in force in the the inverter, and it can be carried out with ease following the procedure
1 2 3 4 5
O
14
11
0 0 NON-ASSIGNED ENGLISH 1 9 CEI-021 @ 230V EXTERNAL Protection (CEI021 EX) ITALIAN
2
9
The grounding of the inputs is negative configuration by default.
J9 J10
MOV1 MOV2
W3
0 1 GERMANY VDE 0126 @ 230V Single Phase (VDE 0126) GERMAN 1 B SOUTH AFRICA @ 230V (S.AFRICA) ENGLISH
For the correct operation, some photovoltaic panels require the connection of the potential of the positive terminal 0 2 UL1741 @ 208V Single Phase (UL208sing) ENGLISH 1 E BELG C10-11 110% @ 230V (C1011 110) FRENCH
5
6
a03
1 1
to the earth terminal, or to have both of the input poles floating in regards to ground potential. J7 J8
1
J5
0 3 UL1741 @ 240V Split Phase (UL240spl) ENGLISH 1 F BRAZIL @ 220V (BRAZIL) ENGLISH
In order to achieve this, it is possible to vary the default configuration, moving the connector installed in a03 (nega- 0 4 UL1741 @ 277V Single Phase (UL277sing) ENGLISH
a04
J19 J20 F1
tive grounding) to a04 (positive grounding) or a02 (floating configuration). 0 5 ENEL GUIDA @ 230V Single Phase (ENEL) ITALIAN
0 6 SPAIN RD 1699 @ 230V (RD 1699) SPANISH
J17 J18 MEMORJ4 CARD CR2032
ND MODE
W2 BT1
W ITE 2 18
11
14
1 17
2
S2
BLACK
The configuration of the grounding of the inputs must be done before any connections or
J J10
5
6
1 2 4
RED
3
1 1 J14
TERM.1 20
J16
RS485(B)
RS485(A)
1 O 1 2
J7 J8 ON
J5 S1 J15 1
DCI N
J17 J18
RS485 CARD
J24
1 2 3 4 1 2 3
IN IN IN IN N L
N.C.
N.O.
T/R
T/R
WT
WT
RID
RTN
LNK
R
R
DC IN
C
ALARM WIND REM RS485
No pole of the array can have earthing connection points located outside the inverter. 0 A AUSTRALIA @ 230V (AS 4777) ENGLISH a09
Incorrect configuration may cause damage to the system and photovoltaic panels! 0 B ISRAEL @ 230V (ISRAEL) ENGLISH
EF0 1
1
BCD
23
10.
45
0 D FRANCE @ 230V (FRANCE) FRENCH
A
6789
BCDE
3456
BCD
23
When exposed to sunlight, the PV panels supply DC direct voltage to the inverter. 1 0 PORTUGAL @ 230V (PORTUGAL) ENGLISH
Input connection (DC)
45
A
6789
789A
The inside of the inverter may only be accessed after the equipment has been disconnected from the grid and from the photovoltaic 1 1 CORSICA @ 230V (CORSICA) FRENCH
generator. 1 2 HUNGARY @ 230V (HUNGARY) ENGLISH
1 3 CHINA @ 230V (CHINA) ENGLISH F 012
2
For the string connections it is necessary to use the quick fit connectors (multicon-
1 4 KOREA @ 220V (KOREA) ENGLISH
BCDE
3456
tact or weidmüller) located on the bottom of the mechanic. Standard Version -S Version
1 5 TAIWAN @ 230V (TAIWAN) ENGLISH 789A
The maximum numbers of input strings which can be connected is 2. GND_MODE
GND_MODE MEMORY CARD
MEMORY
CR2032
J4
CARD CR2032
GND_MODE
GND_MODE MEMORY CARD
MEMORY
CR2032
J4
CARD CR2032
1 6 CHECA Republic @ 230V (CZECH) CZECH
1 7 GERMANY–VDE AR-N-4105 @230V (VDE 4105) GERMAN
J4 BT1 W2 J4 BT1
W2
WHITE 2 18
BT1 W2 WHITE 2 18
BT1
W2
WHITE 2 18
WHITE 2 18
11
14
11
14
11
14
11
14
1 17 1 17
1 17 1 17
GFI GFI
GFI GFI
2
S2
2
BLACK
S2
BLACK
2
J9 J10 S2
2
J9 J10
BLACK
S2 J9 J10 BLACK
Connect all the strings included in the design of the system and always check the
J9 J10 W3 W3 J6
W3 J6 1 W3 1
J6 W4 J6 1
W4 1
W4 W4
MOV1 MOV2 GFI MOV1 MOV2 GFI
5
6
MOV1 MOV2 GFI
5
6
MOV1 MOV2 GFI
5
6
RED
5
6
RED
RS485(B)
RS485(A)
J16
RS485(B)
RS485(A)
OFF J16
RS485(B)
1 2
RS485(A)
OFF J16 1
RS485(B)
1 2
RS485(A)
1
1 OFF 1 2 1
J7 J8 OFF 1 2
J7 J8 ON ON
J7 J8 S1 J15 J7 J8 J5 ON S1 J15 1
J5 ON 1
S1 J15
J5 S1 J15 1 J5 1
The settings become fixed after 24 hours of operation of the inverter ((the PV generator simply has to be under power)).
J24
1 2 3 4 1 2 3 1 2 3 4 1 2 3 1 2 3
1 2 3 4 1 2 3 1 2 3 4
N L -IN -IN +IN +IN N L
If some of the string inputs should not be used you must proceed to verify the
-IN -IN +IN +IN N L
N.C.
N L
N.O.
-IN -IN +IN +IN
T/R
T/R
N.C.
WT
WT
N.O.
-IN -IN +IN +IN
T/R
T/R
RTN
LNK
WT
WT
R
R
GRID
N.C.
RTN
LNK
N.O.
R
R
DC IN
T/R
T/R
GRID
N.C.
WT
WT
N.O.
C
DC IN
T/R
T/R
RTN
LNK
WT
WT
R
R
GRID
RTN
LNK
R
R
GRID DC IN
C
DC IN
C
ALARM WIND REM RS485 ALARM WIND REM RS485
ALARM WIND REM RS485 ALARM WIND REM RS485
presence of covers on DC input connectors 10 and then install them should they The standard for the Italian grid which must be set during installation is 1 -9 (CEI-021 @ 400V INTERNAL Protection)
be absent. This operation is necessary for the tightness of the inverter and to avoid
damaging the free connector that could be used at a later date. 14.
The two pairs of DC input connectors 10 are internally related to a single Connections of the signals to the main board
istics: a03 a01 a04 a02 a05 09 a06 a09 a07 a08 a12 a11 Ref. Ref.
Description
UNO-2.0-I-OUTD UNO-2.5-I-OUTD manual inverter
Type Automatic circuit breaker with differential thermal magnetic protection a01 J9 - J10 Input varistors
Voltage/Current rating 230Vac/16A GND_MODE MEMORY
J4
CARD CR2032 a02 J5 Connector for floating ground of the inputs
Magnetic protection characteristic B/C
W2 BT1
WHITE 2 18
14
11
1 17
GFI
Number of poles 2
2
9
S2
J9 J10 BLACK
5
6
1
RED
1
TERM. 120 J14
J16
RS485(B)
RS485(A)
1 OFF 1 2
MOV3 MOV4 S3
ABB declares that the ABB high-frequency isolated inverters, in terms of their construction, do not inject continuous ground fault currents and therefore there is
J13
J23
17 18
no requirement that the differential protection installed downstream of the inverter be type B in accordance with IEC 60755 / A 2. a07 J4 Inverter data memory card housing
J17 J18
RS485 CARD
J24
1 2 3 4 1 2 3
-IN -IN +IN +IN N L
a08 BT1 Battery housing
N.C.
N.O.
T/R
T/R
WT
WT
GRID
RTN
LNK
R
R
DC IN
C
Characteristics and sizing of the line cable ALARM WIND REM RS485
Rotary switches for setting the standard of the country and the
Three-pole cable required . a10 a15 a14 a13 a09 S1 - S2
language of the display
The cross-section of the AC line conductor must be sized in order to prevent unwanted disconnections of the inverter from the grid due to high impedance of the
line that connects the inverter to the power supply point a10 S3 Switch for setting the termination resistance of the RS485 line
Please refer to the manual for details of the connections and
a11 J16 RS485 communication card housing
functions available on the main board
Cross-section of the line conductor (mm2) Maximum length of the line conductor (m) max 6 mm 2 Connection of the RS485 line on RJ45 1
T/R
T/R
WT
WT
RTN
LNK
R
R
- Remote ON/OFF
WIND REM RS485
- Tachometer signal (WIND version)
For the connection to the inverter grid you need 3 connections: ground, neutral and phase. 1 Terminal block connecting to the configurable
Output connection (AC)
N.C.
O
N O.
The maximum diameter accepted by the cable gland is from 10 to 17 mm while each terminal of the terminal board accepts a cable with can be set are:
C
cross-section which can vary from 0.6 up to 16 mm2 (tightening torque 1.5Nm). 09 -Production -Alarm -Alarm (configura- ALARM
ble) -Crepuscolar
Unscrew the AC cable gland 08 , remove the cover, insert the cable of suitable cross-section and connect the conductors (Ground, Neutral, N L
and Phase) to the terminals on the AC output screw terminal block 09 .
GRID 4
Pay special attention and ensure you do not reverse the phase with the neutral!
Once the connection to the terminal board is complete, screw in the cable gland firmly (tightening torque 5.0Nm) and check the tightness. 09 J21 - J22 AC output terminal board
1 2 3
N L
Before connecting the inverter to the distribution grid it is necessary to set the country standard by manipulating the two rotary switches a09. 2 GRID
15. 17.
The inverter commissioning procedure is as follows: UNO-2.0-I-OUTD UNO-2.5-I-OUTD
Input
Commissioning
--Turn the AC+DC disconnect switch 07 to the ON position Absolute Maximum Input Voltage (Vmax,abs) 520 V
--If there are two separate external disconnect switches (one for DC and the other for AC), first close the AC disconnect switch and then the DC disconnect Input Activation Voltage (Vstart) 200 V (adj. 120...350 V)
Input operating range (Vdcmin...Vdcmax) 0.7 x Vstart...520 V
switch. There is no order of priority for opening the disconnect switches.
Rated DC Input Power (Pdcr) 2100 Wp 2600 Wp
Number of Independent MPPTs 1
--When the inverter has power, the first check performed is the one relating to the input voltage: “2300 W Linear Derating From MAX to “2900 W Linear Derating From MAX to
1. If the DC input voltage is lower than the Vstart voltage (voltage required to begin the inverter’s grid connection) the b14 icon remains off and the “Waiting Maximum Input Power for each MPPT (PMPPTmax)
Null [470V≤VMPPT≤520V]” Null[470V≤VMPPT≤520V]”
sun” message is displayed b10. MPPT Input DC Voltage Range (VMPPTmin,f ... VMPPTmax,f) at Pacr 200...470 V
2. If the DC input voltage is higher than the Vstart voltage the b14 icon is displayed and the inverter goes to the next stage of the controls. Maximum DC Input Current (Idcmax) / for each MPPT (IMPPTmax) 12,5 A / 12,5 A 12.8 A / 12.8 A
In both cases the voltage levels and input current are displayed in the b15 and b16 fields. Maximum Input Short Circuit Current for each MPPT 15.0 A
Maximum Backfeed current (from AC to DC side) Negligible
--The inverter performs a control of grid parameters. The b22 icon, which represents the grid distribution, can have different statuses: Number of DC Inputs Pairs for each MPPT 2
3. not present, if the mains voltage results as absent. DC Connection Type Tool Free PV Connector WM / MC4
4. flashing, if the mains voltage is present but outside the parameters dictated by the standard of the country of installation. Input protection
5. turns on, if the mains voltage is present and within the parameters dictated by the standard of the country of installation. In this condition, the inverter starts Reverse Polarity Protection Yes, from limited current source
the sequence of grid connection. Input Overvoltage Protection for each MPPT - Varistor 2
Photovoltaic Array Isolation Control According to local standard
DC Switch Rating for each MPPT (-S Version) 16 A / 600 V
If the input voltage and the grid voltage are within the inverter operating intervals, connection to the grid will commence. After the inverter is con-
Output
nected, the icons on the whole line b21 will come on steady. AC Grid Connection Type Single phase
Rated AC Power (Pacr) 2000 W 2500 W
Once the connection sequence has been completed, the inverter starts to operate and indicates its correct operation by making a sound and by the Maximum AC Output Power (Pacmax) 2200 W (4) 2750 W (5)
green LED coming on steady on the LED panel 14 . Rated AC Grid Voltage (Vac,r) 230 V
AC Voltage Range 180...264 V (1)
If the inverter signals any errors/warnings the messages and their codes will be indicated on the display 12 . This state will also cause switching of Maximum AC Output Current (Iac,max) 10.5 A 12.5 A
the multi-function relay (set to alarm mode in the menu SETTINGS>Alarm) which activates any external signalling device that may be connected. Maximum output fault current <20Arms (60mS)
Rated Output Frequency (fr) 50 / 60 Hz
16. Output Frequency Range (fmin...fmax)
Nominal Power Factor (Cosphiac,r)
47...53 / 57...63 Hz (2)
> 0.990
The display 12 has a section b10 (graphic display) for moving through the menu using the buttons of the LED panel 14 . Section b10 consists of 2 lines with 16 Total Harmonic Distortion of Current < 2%
Structure of the display menu