Professional Documents
Culture Documents
Procedures Practiced For Quality Control and Assurance (Cutting)
Procedures Practiced For Quality Control and Assurance (Cutting)
1.Ply alignment
2.Ply Tension or Slackness
3.Bowing
4.Splicing
Ply Alignment & Ply Tension
• The greater the variation in width or length
alignment, the greater the waste in the precision
cutting because the ends and sides must be trimmed
to the narrowest and shortest plies.
• Frayed Edges
– May impede cutting time by clogging the knife
action and / or mar the fabric with the rips or
pulled yarns.
– The amount of fraying depends on fabric
construction and finish.
– Improper cutting tools or dull knives cause
excessive fraying in a pattern as section is cut.
Cutting room defects
• Pattern Precision
– Misshape or distortion of the pattern perimeter as
cut. Whether it is under-or overcut is due to poor
manual control of cutting machine and poor lines
on the marker.
– To assure precision in a pattern, check markers
before cutting, use tensionless spreading, or allow
time for fabric to relax.
– After a cut, check the top, bottom, and middle
plies against the pattern.
Cutting room defects
• Notches
– Notch size refers to the depth of the notch. If the depth of the
notch is too great, the notch may show after a garment is sewn.
– If the notches are too small, sewing operators may have
difficulty locating them quickly, resulting in decreased efficiency.
– Misplacement of a notch may be due to an improper spread
marker, poor control of cutting machine with cutter’s notching
tool stroking diagonally instead of vertically, incorrect marker in
that notches for mating parts do not coincide.
– Check notch placement against mating pieces. Quality control in
stitching may be a problem if notches are not aligned.
Cutting room defects
• Drilling
– The drill hole may be too large or too small in diameter.
– In addition, a drill may become too hot due to high speed or
wrong size, causing the plies to fuse together at the drill hole.
– The drill must stroke vertically to the table for uniform
placement throughout the bundle.
– Sometimes fabric properties are such that the slight
movement of yarns in a fabric would close a drill hole.
– In such cases, it is necessary to drill holes with a marking
fluid. The drill used for such purpose is hollow and carries
marking fluid (ink) that is deposited at the drill point on the
fabric as the needle is withdrawn.
– Such marks should last long enough so that further
processing can be finished without difficulty, but should be
easily removable after processing or in case of an error.
Glossary of Cutting room defects
(Pattern, Marker, Spreading and Cutting room defects)
02.
Distorted Grading: Unbalanced patterns which would cause
twisted seams, puckering, pleating and a
general uneconomical yardage waste.
Marking Defects
Shaded Parts: All component pans not included in same section.
Pieces not Symmetrical Will not sew together without puckering or pleating.
Not Marked by Directional Bias will not fit together, causing twisting, puckering,
Lines: pleating and a general mismatching of component
parts.
Notches and Punch Marks: Left out, not clearly marked or misplaced.
Marker Too Wide Parts will not catch in the lay causing skimpy garments
or requiring recuts
Missed Sectional Sectional marker breaks too long or too short. Parts in lay will
Breaks: be short or material wasted.
Improper Tension Cloth spread too tight or too loose, causing parts not to fit in
sewing or distorting dimensions of garments.
Mismatching Plaids: Material spread too loose or too tight causing plaid lines to
run diagonally or bow.
Improper Matching of Not spread face down, face up or face to face as required
Face of Material
Cutting Defects
Marker or Perforator Not stapled or stenciled on lay to catch both edges
causing parts to miss in cutting. Too tight or too loose
distorting dimensions of garment. Perforated stencil
not powdered, or inked sufficiently to show distinct
lines, notches and punch marks
Misplaced Piece Rate Tickets Attached to, or marked on, wrong bundles causing
or Bundle Members mixed sizes and/or shades.
Drill Marks Drill marks misplaced, not perpendicular, omitted or
wrong side drill used.
Opening Slits Cut under above to the side or at incorrect angle. Not
cut through ·entire bundle or omitted.
Improper Cutting Not following marker lines resulting in distorted parts.
Letting knife lean, causing top and bottom ply to be of
different sizes.
Notches Misplaced, too deep, too shallow or omitted.
Oil Spots Equipment improperly oiled or cleaned.
Improper Knife Sharpening Causing ragged, frayed or fused edges on bundles.
Knife or Scissors Cut Piece damaged by over run in cutting previous piece
Shade Marking Defects
Pencil or Machine Too dark, too light, bleeding through, not legible
marking or marked on wrong side.