Professional Documents
Culture Documents
Er 96 2 4 PDF
Er 96 2 4 PDF
CAUTION: To replace a fastener, see parts list for fastener grade and part number. Do not
use a lesser or greater material grade. Use Ariel parts to replace special fasteners and
fasteners with reduced body diameter for fatigue resistance. Do not torque fasteners with
compressor running or pressurized. Read technical manual safety warnings.
Tw = Ta x [L ÷ (L + A)]
Tw = Torque wrench setting, Lb x Ft or N·m.
Ta = Torque required at fastener, Lb x Ft or
N·m. FIGURE 3 Torque Wrench with Angled Adapter
L = Length of wrench, ft or m (from square drive
end to center point of force on handle).
A = Wrench length added by adapter, ft or m (measured to end of adapter on a line parallel to wrench
center line).
Torque
Nominal Size
Fastener Type Lb x Ft (N·m), unless
Inch - TPI
specified
Main Bearing Cap - Cap Screw 7/8 - 9 12 Point - Grade 8 280 (380)
Connecting Rod Cap - Cap Screw 7/8 - 14 12 Point - Grade 8 80 (108) + 90°
1” - 14 See ER-124
Torsional Vibration Detuner - Cap Screw 1” - 14 12 Point - Grade 8 530 (715)
Crankshaft Flange to Nut Plate (JGE:K:T/6) 1/2 - 20 12 Point - Grade 8 46 (62)
a
JGH/4 2-Piece Crankshaft Flange 7/8 - 14 12 Point - Grade 8 Torque to 315 (425),
loosen, then re-torque to
280 (380)
Crosshead Pin Thru Cap Screw - Lock Nut 1/2 - 20 Hex - Nylon Insert 61 (83)
Frame to Spacer Bar - Cap Screw 1-1/8 - 12 12 Point - Grade 8 560 (760)
Crosshead Guide to Frame - Cap Screw 7/8 - 9 12 Point - Grade 8 280 (380)
Crosshead Guide to Cylinder 5/8 - 11 12 Point - Grade 8 97 (130)
7/8 - 9 280 (380)
7/8 - 14 Hex Nut 315 (425)
Crosshead Guide to Support - Cap Screw 7/8 - 9 Hex - Grade 9 255 (345)
12 Point - Grade 8
1” - 8 380 (515)
Head End Cylinder Support to Cylinder 1/2 - 13 Hex - Grade 8 44 (60)
5/8 - 11 88 (120)
3/4 - 10 160 (215)
7/8 - 9 255 (345)
Eccentric Vernier Cap - Cap Screw 5/16 - 18 Hex - Grade 8 Hand Wrench Tight
Idler Sprocket Thru Cap Screw - Lock Nut 1/2 - 20 Hex - Prevailing 41 (55)
5/8 - 18 82 (110)
External Thrust Bearing Adapter to Crankshaft - Cap 1/2 - 20 12 Point - Grade 8 66 (90)
Screw
Rod Packing - Cap Screw b 3/4 - 10 12 Point 125 (170)
Grade 8 or 17-4PH
3/4 - 16 145 (195)
7/8 - 14 230 (310)
Packing Tie Rod - Nut #10 - 24 Hex 20 Lb x In. (2.3)
1/4 - 20 72 Lb x In. (8.1)
Rod Catcher to Packing 1/2 - 20 12 Pt - Grade 8/17-4PH 51 (69)
Piston Nut 1-5/8 - 12 Ariel Design 1590 (2150) c
Piston Nut Set Screw 5/16 - 24 Socket Head 164 Lb x In. (19) d
Crosshead Balance Nut 1-3/4 - 12 Ariel Design Slugging Method e
Force Feed Lube Box - Bearing Housing 1-3/8 - 20 - LH Bearing Housing 70 (95)
Force Feed Lube Box - Jam Nut 1” - 14 Hex 75 (100)
1-1/2 - 12 112 (152)
Force Feed Lube Pump Mounting 1/4 - 20 Hex - Grade 5 50 Lb x In (5.6)
f
Auto Relief Valve 1/2 Ariel Design 75 Lb x In (8.5)
The contents of this document are proprietary and confidential. They are the property of Ariel Corporation and may
not be disclosed, reproduced, or used for manufacture in part or in whole without written permission from Ariel
Corporation.