Professional Documents
Culture Documents
VDR/S-VDR CYC-316 Playback Software / Real Time Monitor Instruction Manual
VDR/S-VDR CYC-316 Playback Software / Real Time Monitor Instruction Manual
Rev. 2006.September.18
Introduction
<Introduction>
Thank you for using the Playback software for our VDR/S-VDR equipment. This software is intended to help
analyze the data recordings that are stored in a capsule or CF card of VDR/S-VDR installed onboard.
This software chronologically plays back all the data including the radar image, bridge and VHF
- Before using the software, read this manual thoroughly to ensure correct use.
- Keep the manual in a convenient location so that it can be used easily whenever necessary.
- Use this manual to check the operation of the software or at the occurrence of a fault.
Microsoft, MS-DOS, and Windows are the registered trademarks of Microsoft Corporation in the U.S.A and /
or other countries.
The names of actual companies and products mentioned herein are the trademarks of their respective
owners.
Attention
(1) The copyright of this software and a manual is in Japan Radio Co., Ltd.
(2) The range as which the Copyright Act determines a part or all of the contents of this software
(3) Although we created to make doubly sure about the contents of this book, if there is a thing of
companion mind, such as a doubtful point, and an error, omission in written, please contact me.
(4) Please understand beforehand that it is not concerned with (3) clauses and any responsibility
cannot be taken about the claim of the loss for reasons of the employed result, loss profits, etc. in
our company.
<Before Using>
Icons
This manual and product employ various icons to enable users to use the product safety and
correctly, and to prevent any harm to users or others, and to prevent damage to the property.
Incorrect use of the equipment by ignoring this icon may cause death or a
WARNING seruous injury.
Incorrect use of the equipment by ignoring this icon may cause an injury or
CAUTION
physical damage.
Example of icons
The △ symbole indicates a caution (including danger or warning).
Inside of the symbol indicates the actual details (this icon indicates the
icon indicates removal of the power plug from socket) are provided inside of
Remove
Plug Instruction the symbol
Do not use any power supply voltage other than the specified voltages.
Such action may cause burst of a battery by liquid leak, fire, or injury.
Do not put containers into which it went, such as water, or a small metal thing on this
When water enters or a metal thing falls into the equipment, it becomes the cause of a fire, an
If put a heavy thing, heat, it pulls or it bends by force, a power cord will be damaged and it
When a fault occurs, turn off the power supply of this equipment, remove the plug, and
contact the Sales Department of Japan Radio Company, nearest branch company, branch
Checking or repair by anyone other than the specialist maintenance staff may cause fire or
electric shock.
Request checking or repair of the inside of the equipment to the sales Department of Japan
Radio Company, nearest branch company, branch office, sales office, or our agent.
CAUTION
Do not install the equipment in the location affected by water, humidity, dust, or soot. It may
Do not put in from a vent foreign substance, such as metal or a thing which is easy to burn.
It may fall and may become the cause of an injury and failure.
It may be filled with heat and fire and failure may occur.
When the equipment is not used for a long time, pull out a power supply plug from a wall
Pull out a plug from a wall socket for safety at the time of care.
If a computer is infected with a virus, it may suffer the damage of an unusual display, a
program, and data being destroyed, and may become the cause of failure.
Please confirm whether it is infected with the computer virus, using a virus checker program
periodically.
<Contents>
<Introduction>............................................................................................................. i
Chapter1 Outline........................................................................................................... 1
3.2 Set a required information for playback with the Setup software.........................................................9
Chapter1 Outline
This software intends to be used for playing back the record data required the International Standard in
Record data
・Sensor data
・Radar image
As an optional function, this software is extended as real time monitor by making LAN connection with
VDR/S-VDR. And real time data can be indicated and recorded by Real Time Monitor side for a long
Further as an expanded function, by connecting with shipboard LAN, you can see the Real Time
In the case of requirement, contact the Sales Department of Japan Radio Company, nearest branch
Blank Page
CD drive : CD-ROM
(2) After a while, Installer starts and the following web screen opens automatically by AUTORUN.
(If the installer does not start, click “SetupE.exe” after selecting the CD drive by My Computer.
・ CD license number
(3) The Installer for the Playback software starts, and the preparation for the installation are
started.
(4) The opening screen is indicated, and click the [Next] button.
(5) The Install Shield Wizard for the Playback software starts, and click the [Next] button.
Please enter user information in the User Name field and the Organization field.
And enter the License number, which is described in the install CD-ROM to the Serial Number
field.
(7) The confirmation screen where the installation folder and user information are shown is
(9) The Install Shield Wizard completion screen is indicated, and click the [Finish] button.
(10) Please eject the Install CD-ROM from the CD drive, and keep the Installation CD-ROM
carefully.
(1) Click the [Start] button and select Control Panel in the Start menu.
Add or Remove
Programs
(3) Select the JCY-1800/1850 VDR Monitor and click the [Remove] button.
(4) Since some files remain in the following installation folder after removal, please open My
And in order to play back record data of CF card, it is necessary to create a playback folder in the
② Set information required for playback with Setup software. ⇒Refer to 3.2
③ Start the Playback software, and copy a record data of CF card. ⇒Refer to 4.6
C:\MV JRC
3.2 Set a required information for playback with the Setup software
(1) Click the JCY-1800 VDR Monitor icon on the desktop.
(3) The Login screen is indicated, and click the [OK] button after confirming that user is selected
(5) Eject a CF card from the VDR/S-VDR, and insert it into the CF card slot of used PC.
Then, to import VDR/S-VDR configuration data, select the following file in the CF card and
Caution When a CF card is ejected from the VDR/S-VDR, please be sure to follow
*: \Init\SysInfo.dat
CF card drive
Note If the [Import] button is clicked and a SysInfo.dat file is not imported, the
[Set] button do not become valid.
(6) Check quantity of engine, rudder, thruster and propeller and so on which are imported by
Quantity selection
(7) Click the [Folder Selection] button, and select a folder created in accordance with the “3.1
(8) Click the [CF Card] drive button, and select a CF card drive.
CF Card button
In order to initialize a playback folder when its folder is created newly, the
Note following dialog screen is indicated.
Chapter4 Operation
4.1 How to start up Playback software
(1) Click the JCY-1800 VDR Monitor icon on the desktop.
indicated.
Setup button
(2) Click the [Exit] button of bottom left in the Setup screen.
Exit button
(4) The Playback screen is closed and it returns to the Launcher menu.
Menu Block.
Main Block
The Playback screen has Voyage screen, Alarm/Status screen, AIS screen and Radar screen on the
Main Block, and their screens are selected with buttons of the Menu Block.
Voyage
Alarm/Status
Menu Block
AIS
Radar
① ⑩
③ ⑪
④ ⑫
③ Slide bar Available to playback from a certain time by sliding the knob.
⑩ Play List button Available to playback after selecting a voyage data registered in the play list.
⑫ Playback Speed Available to select a playback speed from “×1”, ”×2” and “×4”.
(1) Eject a CF Card from VDR/S-VDR, and insert it in the CF card slot.
Caution When a CF card is ejected from the VDR/S-VDR, please be sure to follow
If the drive is not set, please click the [Folder Select] button and select the drive.
(4) Select a playlist in the Copy place box, and click the [Copy] button.
Since the comment dialog appears, and enter some comments if required.
Note The entered comments are indicated in the Comment field.
Please press the [ACK] button in the VDR/S-VDR to stop the alarm.
VDR/S-VDR.
(5) Select radio button of the playlist copied CF card data, and click the [OK] button.
Playlist
radio
button
(6) The setup is completed above, and it is possible to play back with the [Playback] button.
Caution When data copying is finished, please be sure to insert a CF card to the
VDR/S-VDR.
Stop
Playback
Slide bar
Playback time
Slide bar
If the [Forward] button is pressed, a playback time is forwarded. And the step time is
If the [Rewind] button is pressed, a playback time is reversed. And step time is increased by
Forward button
Rewind button
Playback time
Slide bar
Playback time
[Playback] button.)
If “×2” is selected, the playback speed become 2 times faster than normal.
Moreover if “×4” is selected, the playback speed become 4 times faster than normal.
Playback speed
Speaker
If exclude an unnecessary audio source, click the source and remove the “レ” mark.
Moreover if the All mute is clicked and enter the “レ” mark, all sources are muted.
Audio Source
Volume
All Mute
To change the screens, click the [Voyage] button in the Menu block.
Graphic screen
Numeric screen
Voyage
Moreover, if the [True/Relative] button is clicked, it changes to true indication (top is the
True/Relative button
Rudder direction
Heading
voyage.
The following figure is an example in case there are 1 propeller and 1 rudder.
If the [Voyage/Docking] button is clicked, the Ship block is switched to the Docking
screen.
Refer to “4.10.1.5 Ship block (Docking screen)” about the Docking screen.
Voyage screen
Voyage/Docking button
under docking.
The following figure is an example in case there are 1 propeller, 1 rudders and 1 thruster.
If the [Voyage/Docking] button is clicked, the Ship block is switched to the Voyage screen.
Refer to “4.10.1.4 Ship block (Voyage screen)” about the Voyage screen.
Docking screen
Voyage/Docking button
A horizontal axis shows lapsed time and shows the depth of water of the newest at right
end.
Underwate
Seabed
Telegraph Position
Sub-Telegraph Position
Operating Location
In the Numeric screen, all data of the Graphic screen are showed by numeric.
This screen is composed 3 blocks of Alarm/Status, Category Menu and Alarm/Status Menu.
To show door status e.g., click the [Door] button from the Alarm/Status Menu.
Moreover, to show about Steering gear e.g., click the Steering gear from the Category Menu.
Alarm/Status
Category
Menu
Alarm/Status
Menu
Section button
It is prepared so that the icon and the menubar may effectively view the radar screens.
If Radar Interfaces (Option Unit) are added, it is possible to view maximum 4 images.
4.12.1 Icon
① ④
② ⑤
③ ⑥
File Window
Zoom Out Tile
Zoom In Cascade
Print
Close
And simple information of own ship and AIS targets is indicated on right side.
Graphic screen
Simple Information
List Screen
Graphic / List
Centering on own ship, the state of AIS target is indicated on graphics by a symbol.
Screen area is expanded or contracted by the Range button. (Radius: from 0.75 to 24
nm)
AIS Target
Ground).
Ground).
AIS
Base Station
Aids-to
-navigation
Mouse
cursor
Position report, ship's name, IMO number, call sign and length of hull etc are showed in
this screen.
If the [Detail] button in the simple information block, the detail screen is indicated.
If the [Detail] button in the simple information block, the detail screen is indicated.
Setup button
(2) Select the Maintenance tab in the setup and click the [View] button.
Maintenance tab
View button
②
①
Print button
(1) Click the [Setup] button in the Menu Block and select the Version tab.
Setup button
And when the [Setup] button is clicked, setting tabs of each block are indicated, and if a check mark
When Dialogs are changed on the Voyage1 screen, a layout of the Voyage1 screen is changed.
If the Voyage2 screen is changed, please change Dialogs on the Voyage2 screen.
The screen layouts are saved automatically at exiting the Playback software.
Dialog
Exit button
(1/4)
Course Bar
Ship (Voyage)
(2/4)
Ship (Docking)
Current / Wind
Voyage Info
(3/4)
invisible.
“WATER/TRANS/KEEL” mode.
invisible.
invisible.
Engine
Telegraph
(4/4)
background color.
If the Voyage1 screen is restored, press the [Restore] button after opening the Voyage1 screen.
If the Voyage2 screen is restored, press the [Restore] button on the Voyage2 screen.
Save button ※
Restore button
Reread button ※
record for a long time are available as Real Time Monitor. Shows the operation below.
If you require the real time indication and record for a long time, contact
(1) Confirm that the “Live” of the Status block goes out.
(3) The Confirmation screen of indication clear. If it is good, click the [OK] button.
(4) The "Live" lights up yellow, and it changes to real time indication.
green.
The capacity of HDD required in order to record for a long time changes with a record period
Starts the Setup software from the Launcher menu to set them.
(2) Click the [Folder Selection] button in the Setup Folder, and select a record folder.
Before select the record folder, please create the folder with the My Computer.
To create the playback folder, refer to the “3.1 Create a playback folder”.
About Overwrite)
When there is the check in the Overwrite and a record period is exceeded, oldest data is
(2) Since a record folder and free space of a HDD are indicated, and click the [REC] button after
check.
(3) The “REC” in the Status block lights up red, and record is started.
The record by the Real Time Monitor records data which the
Note VDR/S-VDR outputs by a UDP protocol.
not resent. There may be no data in the record data at that time.
(2) When record is stopped, click the [STOP] button. When record is paused, click the [PAUSE]
button.
(3) The “REC” in the Status block goes out, and the record is stopped or paused.
The record data by the Real Time Monitor are saved in the Playlist1.
To play back the record data, select the Playlist1 in accordance with the following operation.
When a LAN cable of the Real Time Monitor is disconnected for playing
Note back in another sitting room, the playback is not possible.
Start the Setup software, and press the Disconnect button in the Ethernet
tab. Then restart the Real Time Monitor, and it is possible to play back.
When the LAN cable is connected again, press the Connect button with
Blank Page
before contact us
1 The real time indication is not Faulty wiring of a LAN cable Check the connections.
possible. The power of the VDR/S-VDR Turn on the power of the VDR
2 The image indication is not The Power of a captured Turn on power of a captured
3 There are no audio outputs of Audio monitoring is not On private, the monitoring may
serviceman is necessary.
Or mute is validated.
4 The record is not possible. Faulty wiring of the external Check the connections.
HDD
5 The audio recording is not The audio recording is not To record, the setup by our
6 The image recording is not The image recording is not as To record, the setup by our
7 Record data are less than a The free space of the HDD is Increase a free space by
record period. not enough for the record deleting unnecessary data, or
8 When a LAN cable of the Real The [Connect] button is In order to operate under
Time Monitor is disconnected, pressed and operation is in the disconnecting the LAN, please
the playback is not possible. state of LAN connection. press the [Disconnect] button
Refer to 4.19.2.4.
Chapter6 Appendix
6.1 How to eject CF card from VDR/S-VDR
Open the door with key.
Key
(2) The CARD LED blinks for 5sec and goes out. Then ejection of CF card becomes possible.
CF CARD SLOT
EJECT button
CARD LED(Green)
MEDIA LED(Red)
Caution When data copying is finished, please be sure to insert a CF card to the
VDR/S-VDR.
If the LED does not light up, the CF card may be faulty.
Please contact us in that case.
Port xx min-1
Ship (Docking) Speed Bow (The left and right in bow) [P/S]xx.x kt $xxVBW
Port xx min-1
(2/4)
Wing e.g.
hh:mm:ss
hh:mm:ss
Override ON/OFF
(3/4)
(Numeric) Keel)
Depth xxx.x m
/Heading Control
/Track Control
/Rudder Control
(4/4)
VDR Engine order and Remote control Port Revolution xx min-1 $xxPRC
order and
Pitch xxx.x deg(°)
response
Stern Revolution xx min-1
Blank Page