Professional Documents
Culture Documents
Epcon C8: Steel Reinforcement Fixings For Reinforced Concrete
Epcon C8: Steel Reinforcement Fixings For Reinforced Concrete
Epcon C8: Steel Reinforcement Fixings For Reinforced Concrete
¬ Epoxy resin
¬ Steel reinforcement fixings for reinforced concrete
European Technical Approval
Mechanical characteristics of rebar
ETA TR 023
n° 07/0189 Nominal 8 10 12 14 16 20 25 32 40
steel
bar Ø
Sections (cm2) 0.503 0.785 1.13 1.54 2.01 3.14 4.91 8.04 12.57
Min. resistances Fe E400 21.13 32.97 47.46 64.68 84.42 131.88 206.22 337.68 527.94
to failure (kN) Fe E500 25.90 40.43 58.20 79.31 103.52 161.71 252.87 414.06 647.36
Ultimate limit
Fe E500 21.85 34.15 49.17 66.93 87.42 136.59 213.43 349.56 546.36
n° 0901501 load NRd (kN)
The mechanical characteristics of the high adhesion rebars are defined in the NFA 35-016 and NFA 35-017
standards.
Anchoring product
P18 822 - NF 030 Sizing rules for steel reinforcement fixings for concrete
Category 5
according to Eurocode 2 regulations and ETA 07/0189
AFNOR AFAQ Certification
11, Avenue Francis de Préssencé The basic anchorage length Lb,rqd (mm) for the ultimate limit load for rebar FRD (N) is given by
F-93571 St Denis la Plaine following equation:
Concrete class fck (Mpa) fbd (Mpa)
C20/25 20 2,3
The product SPIT EPCON C8 C25/30 25 2,7
is NF approved as a category 5 C30/37 30 3,0
anchoring product as per standard C35/45 35 3,4
P18-822.
FRd: Design ultimate load (N) C40/50 40 3,7
It has successfully passed tests C45/55 45 4,0
according to standards P18-831 of fbd : Design value of the bond strength in N/mm2 C50/60 50 4,3
April 93 and P18-836 of July 93.
∅ : Rebar diameter (mm)
η1 : depends on bond conditions - η1 =1 (good bond conditions). See § 8.4.2 (EN 1992-1-1)
Fire behaviour
η2 : depends on rebar diameter - η2 = 1 for Øbar ≤ 32 mm
¬ See page 30
The design anchorage length Lbd (mm) is determined as follow:
PV 26007642-b
With α2 : Influence of concrete With α5 : Influence of the confinement by
minimum cover. transverse pressure.
The factor α5 take into account of the
effect of the pressure transverse to the
plane of splitting along the design length.
p (Mpa) α5
3 0,88
C1
a 5 0,8
7 0,72
C
where p is the transverse pressure at the
ultimate limit state along Lbd in MPa.
ETA 07/0189
Rebar Ø Drilling Ø Anchor length Ultimate limit load (daN) Ultimate limit load (daN) Number of fixings
d0 L bd without influence of centre with influence of centre for Epcon C8 450ml
distance and/or edge (1) distance and/or edge (2) cartridge (3)
(α2 = 0.7) (α2 = 1)
The mechanical characteristics of the high adhesion rebars are defined in the NFA 35-016 and NFA 35-017
standards.
Calculation method
¬ Characteristic bond strength
τRk : 17.85 N/mm2 issues from confirmed test and from the calculation using the
rebar diameter (available for rebar diameter 8 to 40 mm). [τRk = τRu,m x 0.75].