Professional Documents
Culture Documents
Single Mode 1.0625 GBD FC Laser Transceiver 1X9
Single Mode 1.0625 GBD FC Laser Transceiver 1X9
●
11x
●
0.25 typ. ∅.004 M
●
(1.6±0.1)
●
.020 typ.
.063±.004 (b)
●
Z
8x 2.54=20.32
●
0.25 typ.
8x .100=.800
●
.010 typ.
●
1 2 3 4 5 6 7 8 9
●
Rx
●
(25.4±0.1)
●
●
12.7 (2.54)
∅0.3 M A SC
●
RECEPTACLE 2x
8x .100=.800 (2.54)
●
Tx
20.32 .075±.004
●
.100 .800
●
DESCRIPTION
This data sheet describes the Siemens single mode FC transceiver, which
complies with the Fibre Channel Physical and Signaling Interface (FC-PH),
ANSI X3T11 Fiber Channel Physical Standard Class 100-SM-LL-I, Revision
4.3.
The appropriate fiber optic cable is 9 µm (mode field diameter) single
mode fiber with Duplex SC connector.
The Siemens single mode FC transceiver is a single unit comprised of a
transmitter, a receiver and an SC receptacle. It thereby frees the customer
from many alignment and PC board layout concerns. The module is
designed for low cost LAN and WAN applications. It can be used as the
9–42
DESCRIPTION (continued) network end device inter- Recommended Operating Conditions
face in workstations, servers, and storage devices, Parameter Symbol Min. Typ. Max. Units
and in a broad range of network devices such as
bridges, routers, intelligent hubs, and local and wide Case Temperature TC 0 70 °C
area switches. Power Supply Voltage VCC–VEE 4.75 5.0 5.25 V
This transceiver operates at 1.0625 Gbits per second Supply Current(1) ICC 150 300 mA
from a single power supply (+5 Volt). The full differen-
tial data inputs and outputs are PECL compatible. Transmitter
Functional Description of 1x9 Pin Row Transceiver Data Input High Voltage VIH–VCC –1165 –880 mV
This transceiver is designed to transmit serial data via Data Input Low Voltage VIL–VCC –1810 –1475
single mode cable. Input Data Rise/Fall Time, t ,t 100 750 ps
R F
10–90%
Figure 1. Functional diagram
Receiver
Figure 3. Schematic
VCC–TX VCC–RX
1 VCC VCC–RX
9
L1
GND GND VCC
82R
82R
82R
82R
R1 R3 R5 R7
C1 C2
RD
TXD RDN GND GND
SD VCC–TX
TXDN
C1/3=4700 nF VCC-TX L2
130R
200R
130R
130R
130R
(optional) R2 R4 R9 R8
C2/4=4700 nF R1/3/5/7=82 Ohm VCC-RX C3 C4
GND GND R6
L1/2=15000 nH R2/4/6/8=130 Ohm Transceiver GND GNDGND
(L2 is optional) GNDGND GND GND
R9=200 Ohm
The power supply filtering is required for good EMI perfor- is only possible when the power is turned off, then on again
mance. Use short tracks from the inductor L1/L2 to the module (VCCTX switched below VTH).
VCC-RX/VCC-TX. Application board available.
The transceiver contains an automatic shutdown circuit. Reset