Professional Documents
Culture Documents
CATV Operation & Maintenance NC III
CATV Operation & Maintenance NC III
REGULATIONS
MEDIA SECTOR
Page No.
Basic Competencies 2 - 20
Common Competencies 21 - 32
Core Competencies 33 - 52
COMPETENCY MAP
DEFINITION OF TERMS 61 – 65
COMPETENCY MAP 66
ACKNOWLEDGEMENT 67
TRAINING REGULATIONS FOR
CABLE TELEVISION (CATV) OPERATION AND MAINTENANCE NC III
This Qualification is packaged from the competency map of the Media sector) as shown in
Annex A.
This section gives the details of the contents of the basic, common, and core units
of competency required for CATV OPERATION & MAINTENANCE NC III.
BASIC COMPETENCIES
UNIT DESCRIPTOR : This unit covers the knowledge, skills and attitudes required
to lead in the dissemination and discussion of ideas,
information and issues in the workplace.
3. Identify and 3.1. Issues and problems are identified as they arise
communicate issues 3.2. Information regarding problems and issues are
arising in the workplace organized coherently to ensure clear and effective
communication
3.3. Dialogue is initiated with appropriate personnel
3.4. Communication problems and issues are raised as
they arise
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 2
http://www.tesda.gov.ph/downloads/default.asp / secjr
RANGE OF VARIABLES
VARIABLE RANGE
1. Methods of 1.1. Non-verbal gestures
communication 1.2. Verbal
1.3. Face to face
1.4. Two-way radio
1.5. Speaking to groups
1.6. Using telephone
1.7. Written
1.8. Internet
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 3
http://www.tesda.gov.ph/downloads/default.asp / secjr
RANGE OF VARIABLES
VARIABLE RANGE
1. Methods of 1.1. Non-verbal gestures
communication 1.2. Verbal
1.3. Face to face
1.4. Two-way radio
1.5. Speaking to groups
1.6. Using telephone
1.7. Written
1.8. Internet
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 3
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT OF COMPETENCY : LEAD SMALL TEAMS
UNIT CODE : 500311110
UNIT DESCRIPTOR : This unit covers the knowledge, skills and attitudes to lead
small teams including setting and maintaining team and
individual performance standards.
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 5
http://www.tesda.gov.ph/downloads/default.asp / secjr
RANGE OF VARIABLES
VARIABLE RANGE
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 6
http://www.tesda.gov.ph/downloads/default.asp / secjr
EVIDENCE GUIDE
1. Critical aspects of Assessment requires evidence that the candidate:
Competency 1.1. Maintained or improved individuals and/or team
performance given a variety of possible scenario
1.2. Assessed and monitored team and individual
performance against set criteria
1.3. Represented concerns of a team and individual to next
level of management or appropriate specialist and to
negotiate on their behalf
1.4. Allocated duties and responsibilities, having regard to
individual’s knowledge, skills and aptitude and the
needs of the tasks to be performed
1.5. Set and communicated performance expectations for a
range of tasks and duties within the team and provided
feedback to team members
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 7
http://www.tesda.gov.ph/downloads/default.asp / secjr
RANGE OF VARIABLES
VARIABLE RANGE
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 6
http://www.tesda.gov.ph/downloads/default.asp / secjr
RANGE OF VARIABLES
VARIABLE RANGE
1. Preparing for 1.1 Background information on other parties to the
negotiation negotiation
1.2 Good understanding of topic to be negotiated
1.3 Clear understanding of desired outcome/s
1.4 Personal attributes
1.4.1 Self awareness
1.4.2 Self esteem
1.4.3 Objectivity
1.4.4 Empathy
1.4.5 Respect for others
1.5 Interpersonal skills
1.5.1 Listening/reflecting
1.5.2 Non-verbal communication
1.5.3 Assertiveness
1.5.4 Behavior labeling
1.5.5 Testing understanding
1.5.6 Seeking information
1.5.7 self disclosing
1.6 Analytic skills
1.6.1 Observing differences between content
and process
1.6.2 Identifying bargaining information
1.6.3 Applying strategies to manage process
1.6.4 Applying steps in negotiating process
1.6.5 Strategies to manage conflict
1.6.6 Steps in negotiating process
1.6.7 Options within organization and externally
for resolving conflict
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 9
http://www.tesda.gov.ph/downloads/default.asp / secjr
EVIDENCE GUIDE
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 10
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT OF COMPETENCY : SOLVE PROBLEMS RELATED TO WORK ACTIVITIES
UNIT CODE : 500311112
UNIT DESCRIPTOR : This unit of covers the knowledge, skills and attitudes
required to solve problems in the workplace including the
application of problem solving techniques and to determine
and resolve the root cause of problems.
3. Determine corrective 3.1. All possible options are considered for resolution
action of the problem
3.2. Strengths and weaknesses of possible options
are considered
3.3. Corrective actions are determined to resolve the
problem and possible future causes
3.4. Action plans are developed identifying
measurable objectives, resource needs and
timelines in accordance with safety and operating
procedures
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 11
http://www.tesda.gov.ph/downloads/default.asp / secjr
RANGE OF VARIABLES
VARIABLE RANGE
1. Preparing for 1.1 Background information on other parties to the
negotiation negotiation
1.2 Good understanding of topic to be negotiated
1.3 Clear understanding of desired outcome/s
1.4 Personal attributes
1.4.1 Self awareness
1.4.2 Self esteem
1.4.3 Objectivity
1.4.4 Empathy
1.4.5 Respect for others
1.5 Interpersonal skills
1.5.1 Listening/reflecting
1.5.2 Non-verbal communication
1.5.3 Assertiveness
1.5.4 Behavior labeling
1.5.5 Testing understanding
1.5.6 Seeking information
1.5.7 self disclosing
1.6 Analytic skills
1.6.1 Observing differences between content
and process
1.6.2 Identifying bargaining information
1.6.3 Applying strategies to manage process
1.6.4 Applying steps in negotiating process
1.6.5 Strategies to manage conflict
1.6.6 Steps in negotiating process
1.6.7 Options within organization and externally
for resolving conflict
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 9
http://www.tesda.gov.ph/downloads/default.asp / secjr
EVIDENCE GUIDE
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 13
http://www.tesda.gov.ph/downloads/default.asp / secjr
5. Methods of Competency may be assessed through:
Assessment
5.1. Case studies on solving problems in the workplace
5.2. Observation
The unit will be assessed in a holistic manner as is
practical and may be integrated with the assessment of
other relevant units of competency. Assessment will occur
over a range of situations, which will include disruptions to
normal, smooth operation. Simulation may be required to
allow for timely assessment of parts of this unit of
competency. Simulation should be based on the actual
workplace and will include walk through of the relevant
competency components.
6. Context for 6.1. In all workplace, it may be appropriate to assess
Assessment this unit concurrently with relevant teamwork or
operation units.
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 14
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT OF COMPETENCY: USE MATHEMATICAL CONCEPTS AND
TECHNIQUES
UNIT DESCRIPTOR : This unit covers the knowledge, skills and attitudes required
in the application of mathematical concepts and techniques.
PERFORMANCE CRITERIA
ELEMENT Italicized terms are elaborated in the Range of Variables
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 15
http://www.tesda.gov.ph/downloads/default.asp / secjr
RANGE OF VARIABLES
VARIABLE RANGE
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 12
http://www.tesda.gov.ph/downloads/default.asp / secjr
EVIDENCE GUIDE
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 17
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT OF COMPETENCY: USE RELEVANT TECHNOLOGIES
UNIT DESCRIPTOR : This unit of competency covers the knowledge, skills, and
attitude required in selecting, sourcing and applying
appropriate and affordable technologies in the workplace.
PERFORMANCE CRITERIA
ELEMENT Italicized terms are elaborated in the Range of Variables
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 18
http://www.tesda.gov.ph/downloads/default.asp / secjr
RANGE OF VARIABLES
VARIABLE RANGE
1. Technology May include but are not limited to:
1.1 Office technology
1.2 Industrial technology
1.3 System technology
1.4 Information technology
1.5 Training technology
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 19
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT OF COMPETENCY: USE MATHEMATICAL CONCEPTS AND
TECHNIQUES
UNIT DESCRIPTOR : This unit covers the knowledge, skills and attitudes required
in the application of mathematical concepts and techniques.
PERFORMANCE CRITERIA
ELEMENT Italicized terms are elaborated in the Range of Variables
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 15
http://www.tesda.gov.ph/downloads/default.asp / secjr
COMMON COMPETENCIES
2. Prepare hand tools 2.1. Appropriate hand tools are checked for proper
operation and safety
2.2. Unsafe or faulty tools are identified and marked for
repair according to standard company procedure
3. Use appropriate hand 3.1. Tools are used according to tasks undertaken
tools and test equipment 3.2. All safety procedures in using tools are observed
at all times and appropriate personal protective
equipment (PPE) are used
3.3. Malfunctions, unplanned or unusual events are
reported to the supervisor
4. Maintain hand tools 4.1. Tools are handled without damage according to
procedures
4.2. Routine maintenance of tools undertaken
according to standard operational procedures,
principles and techniques
4.3. Tools are stored safely in appropriate locations in
accordance with manufacturer’s specifications or
standard operating procedures
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 21
http://www.tesda.gov.ph/downloads/default.asp / secjr
RANGE OF VARIABLES
VARIABLE RANGE
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 22
http://www.tesda.gov.ph/downloads/default.asp / secjr
EVIDENCE GUIDE
5. Resource Implication 5.1. Tools may include the following but not limited to:
5.1.1. screw drivers
5.1.2. pliers
5.1.3. punches
5.1.4. wrenches, files
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 23
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT OF COMPETENCY: USE RELEVANT TECHNOLOGIES
UNIT DESCRIPTOR : This unit of competency covers the knowledge, skills, and
attitude required in selecting, sourcing and applying
appropriate and affordable technologies in the workplace.
PERFORMANCE CRITERIA
ELEMENT Italicized terms are elaborated in the Range of Variables
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 18
http://www.tesda.gov.ph/downloads/default.asp / secjr
RANGE OF VARIABLES
VARIABLE RANGE
1. Measuring instruments 1.1. Straight edge
1.2. Torque gauge
1.3. Try square
1.4. Protractor
1.5. Combination gauge
1.6. Steel rule
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 25
http://www.tesda.gov.ph/downloads/default.asp / secjr
EVIDENCE GUIDE
4.1. Observation
4.2. Oral questioning
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 26
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT TITLE : PREPARE AND INTERPRET TECHNICAL DRAWING
UNIT CODE : ELC311202
UNIT DESCRIPTOR : This unit covers the knowledge, skills and attitudes and values
needed to prepare/interpret diagrams, engineering abbreviation
and drawings, symbols, dimension.
4. Store technical drawings and 4.1. Care and maintenance of drawings are
equipment /instruments undertaken according to company
procedures.
4.2. Technical drawings are recorded and
inventory is prepared in accordance with
company procedures.
4.3. Proper storage of instruments is undertaken
according to company procedures.
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 27
http://www.tesda.gov.ph/downloads/default.asp / secjr
COMMON COMPETENCIES
2. Prepare hand tools 2.1. Appropriate hand tools are checked for proper
operation and safety
2.2. Unsafe or faulty tools are identified and marked for
repair according to standard company procedure
3. Use appropriate hand 3.1. Tools are used according to tasks undertaken
tools and test equipment 3.2. All safety procedures in using tools are observed
at all times and appropriate personal protective
equipment (PPE) are used
3.3. Malfunctions, unplanned or unusual events are
reported to the supervisor
4. Maintain hand tools 4.1. Tools are handled without damage according to
procedures
4.2. Routine maintenance of tools undertaken
according to standard operational procedures,
principles and techniques
4.3. Tools are stored safely in appropriate locations in
accordance with manufacturer’s specifications or
standard operating procedures
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 21
http://www.tesda.gov.ph/downloads/default.asp / secjr
EVIDENCE GUIDE
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 29
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT TITLE : APPLY QUALITY STANDARDS
UNIT CODE : ELC315202
UNIT DESCRIPTOR : This unit covers the knowledge, skills, (and) attitudes and
values needed to apply quality standards in the workplace.
The unit also includes the application of relevant safety
procedures and regulations, organization procedures and
customer requirements
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 30
http://www.tesda.gov.ph/downloads/default.asp / secjr
RANGE OF VARIABLES
VARIABLE RANGE
1. Materials/components 1.1. Materials may include but not limited to:
1.1.1. Wires
1.1.2. Cables, soldering lead
1.1.3. Electrical tape
1.2. Components may include but not limited to:
1.2.1. ICs
1.2.2. Diodes
4. Quality standards 4.1. Quality standards may relate but not limited to
the following:
4.1.1. Materials
4.1.2. Component parts
4.1.3. Final product
4.1.4. Production processes
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 31
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT TITLE : PERFORM MENSURATION AND CALCULATION
UNIT CODE : ELC311201
UNIT DESCRIPTOR : This unit covers the knowledge, skills and attitudes and values
needed identify, care, handle and use measuring instruments
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 24
http://www.tesda.gov.ph/downloads/default.asp / secjr
CORE COMPETENCIES
1. Plan and prepare 1.1 Installation procedures are planned and prepared based
CATV system on industry standards.
installation 1.2 Appropriate personnel are consulted to ensure the work is
coordinated effectively with others involved in the work site.
1.3 Installation plan and materials are checked against
requirements
1.4 Tools, equipment and testing devices needed to carry out
the installation work are obtained in accordance with
established procedures and checked for correct operation
and safety
3 Inspect and 3.1 Final inspections and performance checks are undertaken
document to ensure that the installation procedures of devices,
completion of work materials and equipment conforms to industry standards
3.2 Joint-pole agreement is strictly observed and provisions
stipulated on the NTC provisional authority is complied
3.3 Work completion is documented and reported to personnel
concerned in accordance with established procedures
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 33
http://www.tesda.gov.ph/downloads/default.asp / secjr
RANGE OF VARIABLES
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 34
http://www.tesda.gov.ph/downloads/default.asp / secjr
EVIDENCE GUIDE
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 35
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT TITLE : PREPARE AND INTERPRET TECHNICAL DRAWING
UNIT CODE : ELC311202
UNIT DESCRIPTOR : This unit covers the knowledge, skills and attitudes and values
needed to prepare/interpret diagrams, engineering abbreviation
and drawings, symbols, dimension.
4. Store technical drawings and 4.1. Care and maintenance of drawings are
equipment /instruments undertaken according to company
procedures.
4.2. Technical drawings are recorded and
inventory is prepared in accordance with
company procedures.
4.3. Proper storage of instruments is undertaken
according to company procedures.
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 27
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT OF COMPETENCY : COMMISSION CATV SYSTEM
UNIT CODE : MDA311301
DESCRIPTOR : This unit covers the knowledge, skills and attitudes
required to perform commissioning of CATV system
which may include headend and outside plant system.
This covers the activation of headend equipment, cable
powering, energizing and adjustment of proper signal
level.
PERFORMANCE CRITERIA
ELEMENT
(Italicized Bold terms are elaborated in the range of variables)
1. Test-run headend 1.1 Test instruments and equipment are prepared and
equipment checked prior to test run.
1.2 Signal levels are measured and set per channel based on
standard headend parameters
1.3 Signals are combined/mixed in such a way that signal
levels are at the same prescribed level to properly drive
the launching amplifier.
1.4 Re-adjustments/re-alignments of questionable channels
and equipment diagnosis are performed in case of
abnormal test results
1.5 Results of tests and measurements per channel are
documented in accordance with company requirements.
2. Test-run auxiliary 2.1 Operation of air-conditioning system is tested and
equipment compared with required ambient temperature for headend
equipment operation.
2.2 Standby generator is test-run for proper voltage and
frequency regulation.
2.3 Test results are recorded and documented in accordance
with job requirements.
2.4 Problems encountered in operation of equipment
accessories are documented and referred to concerned
personnel in accordance with company procedures.
3. Activate OSP 3.1 Appropriate tools, test instrument, equipment,
power supplies materials and PPE are prepared and checked prior to
activation of power.
3.2 Power switch is switched on and input and output
voltages are measured and recorded.
4 Energize OSP 4.1 Trunk amplifiers are activated and energized to the
distribution system correct signal level as per design plan
4.2 Line extender amplifiers are activated and energized to
deliver proper signal level as per design plan
4.3 Safety precautions are observed and followed in climbing
poles and powering of each amplifier.
4.4 Measurements and results of tests are recorded and
documented in accordance with established procedures
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 37
http://www.tesda.gov.ph/downloads/default.asp / secjr
RANGE OF VARIABLES
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 38
http://www.tesda.gov.ph/downloads/default.asp / secjr
6 Measured voltages 6.1 input voltage ~ (220 V, sine wave)
6.2 output voltage ~ (60 V, quasi-square wave)
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 39
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT TITLE : APPLY QUALITY STANDARDS
UNIT CODE : ELC315202
UNIT DESCRIPTOR : This unit covers the knowledge, skills, (and) attitudes and
values needed to apply quality standards in the workplace.
The unit also includes the application of relevant safety
procedures and regulations, organization procedures and
customer requirements
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 30
http://www.tesda.gov.ph/downloads/default.asp / secjr
4. Resource The following resources should be available:
implications 4.1. Design plan
4.2. Tools, test equipment, materials and PPE
4.3. Work area
4.4. Technical data
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 41
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT OF COMPETENCY : OPERATE CATV SYSTEM
UNIT CODE : MDA311302
DESCRIPTOR : This unit covers the knowledge, skills and attitudes
required to monitor, interpret/analyze, adjust and
calibrate CATV system’s performance in the day-to-day
operation as well as monitoring and attending to
subscribers/customers’ complaints.
PERFORMANCE CRITERIA
ELEMENT
(Italicized Bold terms are elaborated in the range of variables)
2 Monitor CATV system 2.1 Appropriate PPE are selected and used in the
performance performance of the job.
2.2 Equipment signal-levels are monitored for normal
readings based on established reference parameters.
2.3 Normal and abnormal operations/readings are recorded
and noted.
2.4 Where applicable, immediate remedies are made to
sustain normal operation.
2.5 Action taken are logged and documented in accordance
with established procedures.
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 42
http://www.tesda.gov.ph/downloads/default.asp / secjr
RANGE OF VARIABLES
VARIABLE RANGE
1. Immediate May include:
remedies 1.1 Adjustment of signal levels at particular channel/s
1.2 Replacement with spare unit
1.3 Tightening loose connections, cables/cords, plugs, switches
1.4 Cleaning dirty surfaces and parts
1.5 Cutting in of emergency power
1.6 Splicing cable cuts
1.7 Replacement of corroded connectors
1.8 Replacement of slow-blow fuses
1.9 Resetting of circuit breakers
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 43
http://www.tesda.gov.ph/downloads/default.asp / secjr
CORE COMPETENCIES
1. Plan and prepare 1.1 Installation procedures are planned and prepared based
CATV system on industry standards.
installation 1.2 Appropriate personnel are consulted to ensure the work is
coordinated effectively with others involved in the work site.
1.3 Installation plan and materials are checked against
requirements
1.4 Tools, equipment and testing devices needed to carry out
the installation work are obtained in accordance with
established procedures and checked for correct operation
and safety
3 Inspect and 3.1 Final inspections and performance checks are undertaken
document to ensure that the installation procedures of devices,
completion of work materials and equipment conforms to industry standards
3.2 Joint-pole agreement is strictly observed and provisions
stipulated on the NTC provisional authority is complied
3.3 Work completion is documented and reported to personnel
concerned in accordance with established procedures
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 33
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT OF COMPETENCY : IMPLEMENT PREVENTIVE MAINTENANCE OF CATV
SYSTEM
UNIT CODE : MDA311303
DESCRIPTOR : This unit covers the knowledge, skills and attitudes
required to perform/implement preventive maintenance
of cable television headend and outside plant.
PERFORMANCE CRITERIA
ELEMENT
(Italicized Bold terms are elaborated in the range of variables)
1 Plan and prepare 1.1 Preventive maintenance checks are identified and
schedules for documented based on established plan and procedures.
maintenance 1.2 Appropriate materials, tools, test instruments and
equipment are identified and selected based on job
requirements.
1.3 Inventory of spare equipment and materials are
identified and listed in accordance with job requirements.
2 Carry out preventive 2.1 Appropriate personal protective equipment (PPE) is
maintenance used in accordance with OHS requirements.
2.2 Scheduled preventive maintenance activities are
strictly followed and implemented as per plan.
2.3 Identified equipment and accessories that will cause
potential problems are scheduled for repair and/or
replacement.
2.4 Inventory of spare equipment and materials are
maintained in accordance with established industry
practices.
2.5 Unusual problems encountered are noted and referred
to concerned personnel for appropriate action.
3 Prepare preventive 3.1 Preventive maintenance log book is properly
maintenance report accomplished.
3.2 Inventory stock levels are recorded in the stock cards as
per company policy.
3.3 Recommendations for preventive maintenance are
prepared and referred to concerned personnel.
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 45
http://www.tesda.gov.ph/downloads/default.asp / secjr
RANGE OF VARIABLES
VARIABLE RANGE
1. preventive Preventive maintenance checks may include:
maintenance HEADEND:
checks 1.1 Mechanical
1.1.1. air-conditioning units
1.1.2. emergency generator
1.1.3. antenna tower structures
1.1.4. building structures
1.1.5. facility grounding and bonding
1.1.6. lightning arresters
1.1.7. satellite dish structures
1.2 Electrical/Electronics
1.2.1. signal processing equipment
1.2.2. satellite receivers
1.2.3. modulators
1.2.4. systems converters
1.2.5. automatic voltage regulators (AVR)
1.2.6. antenna pre-amps, LNB/LNA and downleads
1.2.7. equipment interconnecting cables
1.2.8. electrical wirings and lightings
1.2.9. security alarm systems (optional)
OUTSIDE PLANT:
1.1 Mechanical
1.1.1. equipment attachments
1.1.2. cable attachments
1.1.3. guying and bonding
1.1.4. connectorization
1.2 Electrical/electronics
1.2.1. power supplies
1.2.2. active and passive devices
1.2.3. grounding
2. spare equipment This may include:
and materials 2.1 Equipment
2.1.1. agile modulator
2.1.2. agile demodulator
2.1.3. satellite receiver
2.1.4. signal processor
2.1.5. super heterodyne processor
2.1.6. low-noise block down converter (LNB)
2.1.7. power divider
2.1.8. AVR
2.2 Materials
2.2.1. RG-6 coaxial cable
2.2.2. connectors
2.2.3. hardware, supplies and spare parts
2.2.4. heat shrink
2.2.5. silicon gel
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 46
http://www.tesda.gov.ph/downloads/default.asp / secjr
3. PPE PPE may include:
3.1 safety belt
3.2 rubber gloves
3.3 safety shoes
3.4 safety ladder
3.5 hard hat
3.6 safety goggles
4. preventive Activities may include:
maintenance 4.1 Pest control activities (insects, rodents, birds, termites)
activities 4.2 Grass trimming/cutting
4.3 Tree branch trimming
4.4 Cleaning/sweeping/vacuum-cleaning of floors and equipment
surfaces and air-con filters
4.5 Lubrication of satellite dish mechanism and emergency
generator
4.6 Anti-corrosion on grounding facilities
4.7 Adjustments of output levels of processors, modulators, and
satellite receivers
4.8 Check standby power supplies for the following:
4.8.1. Corrosion on battery terminals and power-supply housing
4.8.2. Float and charging voltage of standby power supplies
4.8.3. Open-circuit voltage of each standby battery (difference with
each battery in the series should not be more than 0.5 VDC
and each battery should not be less than 10.5 VDC); replace
batteries if more than 0.5 VDC difference
4.8.4. Physical condition of AC capacitor [(oil leaks and deformed
appearance) CAUTION: Beware of high voltages on the AC
capacitor]; recommend replacement of leaky capacitors.
4.9 Signal test and voltage check of trunk amplifiers and line-
extender amplifiers
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 36
http://www.tesda.gov.ph/downloads/default.asp / secjr
EVIDENCE GUIDE
1. Critical aspects of Assessment requires evidence that the candidate:
competency 1.1. Complied with job requirements and safety procedures at all times
during preventive maintenance implementation
1.2. Implemented and strictly followed schedule of preventive
maintenance activities as per plan
1.3. Communicated and worked with relevant personnel
2. Underpinning The candidate must be able to demonstrate knowledge on the following:
knowledge and 2.1 Safety Practices
attitude 2.1.1 Work safety requirements
2.1.2 Proper use of tools and equipment
2.2 Materials, Tools and Equipment:
2.2.1 Uses and Specifications
2.2.2 Identification of appropriate tools, equipment; and devices
2.3 Theory and Practices
2.3.1 Preventive maintenance concepts and procedures
2.3.2 System sweeping
2.3.3 CATV Headend technology
2.3.3.1 Signal sources
2.3.3.2 Signal processing
2.3.3.3 Signal mixing
2.3.3.4 Facility grounding
2.3.3.5 Air-conditioning system
2.3.3.6 Power sources
2.3.4 CATV Outside Plant
2.3.4.1 Distribution cables
2.3.4.2 Active devices
2.3.4.3 Passive devices
2.3.4.4 Pole hardware
2.3.4.5 Grounding and bonding
2.3.4.6 System alignment and balancing
2.4 Desirable work values and attitudes (cost conscious, safety
conscious, quality conscious, etc.)
3. Underpinning 3.1. Working efficiently and systematically
skills 3.2. Observing safety precautions
3.3. Proper handling, use and maintenance of tools and equipment
3.4. Analytical skills
3.5. Communicate effectively
3.6. documentation skills
4. Resource The following resources should be available:
implications 4.1. Tools, test instruments, equipment, materials and PPE
4.2. Work area
4.3. Maintenance log
4.4. Reference/Historical data (for work area or simulated CATV
system)
4.5. Technical manuals (optional)
5. Method of 5.1. Direct observation/demonstration with oral questioning
assessment 5.2. Third Party Report
5.3. Portfolio
6. Context of 6.1. Competency maybe assessed in the workplace or in a simulated
assessment workplace setting
6.2. Assessment shall be undertaken either individually or part of team
under limited supervision
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 49
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT OF COMPETENCY : PERFORM CATV SYSTEM TROUBLESHOOTING
AND REPAIR
UNIT CODE : MDA311304
DESCRIPTOR : This unit covers the knowledge, skills and attitudes
required to perform corrective maintenance for CATV
systems which includes scheduling of works, analyzing
and identifying trouble/defect and implementing
appropriate repair or correction.
PERFORMANCE CRITERIA
ELEMENT
(Italicized Bold terms are elaborated in the range of variables)
1 Receive and 1.1 Sort out the received job orders, arrange and plan
acknowledge service- effective/efficient route to implement the required job.
request job orders 1.2 Service requests are prioritized according to urgency of
request and volume of complaints per service area.
1.3 Necessary equipment, tools and materials are
requested from stock room in accordance with company
policies and procedures.
3 Perform post-service 3.1 At the end of the day, all accomplished job orders are
procedures per summarized on the daily job accomplishment report form
company policy and submitted to technical supervisor/office manager.
3.2 Unused/pulled-out equipment and/or materials are
documented and returned to the stock man for
acknowledgment.
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 50
http://www.tesda.gov.ph/downloads/default.asp / secjr
RANGE OF VARIABLES
VARIABLE RANGE
1. Necessary May include but not limited to:
equipment, tools 1.1 Field intensity meter
and materials 1.2 Digital voltmeter
1.3 TV receiver/monitor
1.4 Set of hand tools
1.4.1. long nose pliers
1.4.2. diagonal side cutter
1.4.3. screwdrivers
1.4.4. wrenches
1.5 Spare active and passive devices
1.6 Coaxial cables
1.7 Connectors
1.8 Weatherproofing materials
1.9 Spare power supply module
2. Trouble/defect May include but is not limited to:
2.1 Poor or no reception
2.2 Cross modulation
2.3 Intermittent reception
2.4 Poor or no signal on some channels
2.5 Clear picture but no sound or vice versa
2.6 Black-and-white picture in color TV set
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 51
http://www.tesda.gov.ph/downloads/default.asp / secjr
6 Measured voltages 6.1 input voltage ~ (220 V, sine wave)
6.2 output voltage ~ (60 V, quasi-square wave)
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 39
http://www.tesda.gov.ph/downloads/default.asp / secjr
SECTION 3 TRAINING STANDARDS
Course Description:
This course is designed to develop & enhance the knowledge, skills, & attitudes of a
CATV Technician, in accordance with industry standards. It covers the basic & common
competencies in addition to the core competencies such as commissioning consumer
electronic products and systems, developing servicing system for consumer electronic
products and training service technicians. The nominal duration of 176 hours covers the
required units at Cable Television Operation & Maintenance NC III. TVET providers can
however, offer a longer, ladderized course covering both NC II and NC III basic, common
and core units.
BASIC COMPETENCIES
36 hrs
Unit of Assessment
Learning Outcomes Methodology
Competency Approach
1. Lead workplace 1.1 Communicate information Group discussion Observation
communication about workplace Role Play Interviews
processes. Brainstorming
1.2 Lead workplace
discussions.
1.3 Identify and communicate
issues arising in the
workplace
2. Lead small 2.1 Provide team leadership. Lecture Demonstration
teams 2.2 Assign responsibilities Demonstration Case studies
among members. Self-paced
2.3 Set performance (modular)
expectation for team
members.
2.4 Supervise team
performance
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 53
http://www.tesda.gov.ph/downloads/default.asp / secjr
3. Develop and 3.1 Identify relevant Direct Written test
practice information in planning observation Practical/
negotiation negotiations Simulation/role performance
skills 3.2 Participate in negotiations playing test
3.3 Document areas for Case studies
agreement
4. Solve 4.1 Explain the analytical Direct observation Written test
workplace techniques. Simulation/role Practical/
problem related 4.2 Identify the problem. playing performance
to work 4.3 Determine the possible Case studies test
activities cause/s of the problem
5. Use 5.1 Identify mathematical Direct observation Written test
mathematical tools and techniques to Simulation/role Practical/
concepts and solve problem playing performance
techniques 5.2 Apply mathematical Case studies test
procedures/solution
5.3 Analyze results
6. Use relevant 6.1 Identify appropriate Direct observation Written test
technologies technology Simulation/role Practical/
6.2 Apply relevant technology playing performance
6.3 Maintain/enhance Case studies test
relevant technology
COMMON COMPETENCIES
44 hrs
Note: Those who have completed the course on CATV Installation NC II or have acquired the
CATV Installation NC II qualification can skip this portion on common competencies
Unit of Assessment
Learning Outcomes Methodology
Competency Approach
1 Apply Quality 1.1 Check materials and Field trip Demonstration &
Standards replace faulty ones in Symposium questioning
accordance with Film showing Observation &
workplace standards and Simulation questioning
requirements On-the-job Third party
1.2 Carry out work training report
assignments in
accordance with standard
operating procedures
1.3 Check completed work
against standards and
specifications
1.4 Document and prepare a
report on deviations from
specific quality standards
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 54
http://www.tesda.gov.ph/downloads/default.asp / secjr
2 Use Hand 2.1 Identify tasks to be Lecture / Written/Oral
Tools undertaken and the Demonstration examination
appropriate tools to Distance Practical
perform the task learning demonstration
2.2 Prepare and check the Film Showing Observation and
required hand tools and questioning
use them properly
2.3 Use appropriate hand
tools and test equipment
in accordance with safety
rules and procedure
2.4 Perform basic
maintenance procedures
on hand tools and test
equipment
3 Perform 3.1 Identify tasks to be Self- paced/ Written/Oral
Mensuration performed and the modular examination
and appropriate measuring Lecture/ Practical
Calculation instruments required Demonstration demonstration
3.2 Perform measurement and Small group
calculation tasks discussion
according to specifications Distance
and requirements learning
3.3 Perform basic
maintenance tasks on
measuring instruments
according to established
rules and procedure
4 Prepare and 4.1 Identify and select the Lecture/ Written /oral
Interpret appropriate technical demonstration examinations
Technical drawing required Dualized Direct
Drawings 4.2 Identify symbols and training observation
Interpret the technical Distance Project method
drawing properly learning interview
4.3 Check and validate
drawing requirements and
prepare/make changes on
electrical/electronic
schematics and drawings
4.4 Explain how to record and
store technical drawings,
equipment and
instruments properly
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 55
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT OF COMPETENCY : OPERATE CATV SYSTEM
UNIT CODE : MDA311302
DESCRIPTOR : This unit covers the knowledge, skills and attitudes
required to monitor, interpret/analyze, adjust and
calibrate CATV system’s performance in the day-to-day
operation as well as monitoring and attending to
subscribers/customers’ complaints.
PERFORMANCE CRITERIA
ELEMENT
(Italicized Bold terms are elaborated in the range of variables)
2 Monitor CATV system 2.1 Appropriate PPE are selected and used in the
performance performance of the job.
2.2 Equipment signal-levels are monitored for normal
readings based on established reference parameters.
2.3 Normal and abnormal operations/readings are recorded
and noted.
2.4 Where applicable, immediate remedies are made to
sustain normal operation.
2.5 Action taken are logged and documented in accordance
with established procedures.
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 42
http://www.tesda.gov.ph/downloads/default.asp / secjr
3.2 TRAINING DELIVERY
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 57
http://www.tesda.gov.ph/downloads/default.asp / secjr
3.3 TRAINEE ENTRY REQUIREMENTS
The trainees who wish to enter the course should possess the following
requirements:
Must have completed Cable TV Installation NCII program or equivalent
can communicate either oral or written;
must be physically and mentally fit to undergo training
high school graduate or equivalent
with basic computer skills; and
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 58
http://www.tesda.gov.ph/downloads/default.asp / secjr
3.5 TRAINING FACILITIES
Total 128
Facilities / Equipment / 37
Circulation**
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 59
http://www.tesda.gov.ph/downloads/default.asp / secjr
UNIT OF COMPETENCY : IMPLEMENT PREVENTIVE MAINTENANCE OF CATV
SYSTEM
UNIT CODE : MDA311303
DESCRIPTOR : This unit covers the knowledge, skills and attitudes
required to perform/implement preventive maintenance
of cable television headend and outside plant.
PERFORMANCE CRITERIA
ELEMENT
(Italicized Bold terms are elaborated in the range of variables)
1 Plan and prepare 1.1 Preventive maintenance checks are identified and
schedules for documented based on established plan and procedures.
maintenance 1.2 Appropriate materials, tools, test instruments and
equipment are identified and selected based on job
requirements.
1.3 Inventory of spare equipment and materials are
identified and listed in accordance with job requirements.
2 Carry out preventive 2.1 Appropriate personal protective equipment (PPE) is
maintenance used in accordance with OHS requirements.
2.2 Scheduled preventive maintenance activities are
strictly followed and implemented as per plan.
2.3 Identified equipment and accessories that will cause
potential problems are scheduled for repair and/or
replacement.
2.4 Inventory of spare equipment and materials are
maintained in accordance with established industry
practices.
2.5 Unusual problems encountered are noted and referred
to concerned personnel for appropriate action.
3 Prepare preventive 3.1 Preventive maintenance log book is properly
maintenance report accomplished.
3.2 Inventory stock levels are recorded in the stock cards as
per company policy.
3.3 Recommendations for preventive maintenance are
prepared and referred to concerned personnel.
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 45
http://www.tesda.gov.ph/downloads/default.asp / secjr
DEFINITION OF TERMS
GENERAL
3) Common Competencies - are the skills and knowledge needed by all people
working in a particular industry
8) Core Competencies - are the specific skills and knowledge needed in a particular
area of work - industry sector/occupation/job role
10) Elective Competencies - are the additional skills and knowledge required by the
individual or enterprise for work
11) Elements - are the building blocks of a unit of competency. They describe in
outcome terms the functions that a person performs in the workplace.
13) Level - refers to the category of skills and knowledge required to do a job
14) Method of Assessment - refers to the ways of collecting evidence and when,
evidence should be collected
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 61
http://www.tesda.gov.ph/downloads/default.asp / secjr
15) National Certificate (NC) – is a certification issued to individuals who achieve all
the required units of competency for a national qualification defined under the
Training Regulations. NCs are aligned to specific levels within the PTQF
17) Qualification - is a cluster of units of competencies that meets job roles and is
significant in the workplace. It is also a certification awarded to a person on
successful completion of a course in recognition of having demonstrated
competencies in an industry sector
18) Range of Variables - describes the circumstances or context in which the work is
to be performed
20) Resource Implications - refers to the resources needed for the successful
performance of the work activity described in the unit of competency. It includes
work environment and conditions, materials, tools and equipment
21) Basic Competencies - are the skills and knowledge that everyone needs for work
22) Training Regulations (TR) – refers to the document promulgated and issued by
TESDA consisting of competency standards, national qualifications and training
guidelines for specific sectors/occupations. The TR serves as basis for
establishment of qualification and certification under the PTQF. It also serves as
guide for development of competency-based curricula and instructional materials
including registration of TVET programs offered by TVET providers
24) Underpinning Skills - refers to the list of the skills needed to achieve the elements
and performance criteria in the unit of competency. It includes generic and
industry specific skills
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 62
http://www.tesda.gov.ph/downloads/default.asp / secjr
SECTOR SPECIFIC
3. Bridger amplifier – a device which extracts a portion of the signal from the trunk,
amplifies it to a higher level, and feeds it to the distribution system.
4. Cable – is used for the distribution of television signals from the headend to the
subscribers. The nominal characteristic impedance used in CATV system must be 75-
ohms.
5. CATV – any facility that, in whole or in part, receives directly or indirectly over the air,
and amplifies or otherwise modifies (improves) the signals transmitting programs
broadcast by one or more television, satellite or radio stations and distributes such
signals by wire or cable to subscribing members of the public who pay for such service
or services.
8. Directional couplers – is a device used to divide the power unequally into two paths.
9. Drop cable – a small-diameter cable leading from the tap-off in the cable plant to the
subscribers’ TV receivers. A drop cable used by the CATV system should be either RG-
59 or RG-6, 75-ohms coaxial cable (foam).
10. Environment - The area surrounding the work site which can be directly or indirectly
affected by occurrences at the work site. It includes the atmosphere, soils, drains,
underground water tables, and the ecosystem. Protection of the environment would
require the proper disposal of waste materials, restriction of burning off, the correct
handling of toxic substances, the containment of CFCs and the like.
12. Hazardous materials - Flammable gases and vapors and combustible dusts.
13. Headend – is the main site at which all the signals from the various program sources
are received, assembled, processed and combined for transmission through the
distribution network. It is the originating point for all services carried on a cable television
system
14. Line extender amplifier – extends further the feederline from the trunk bridger.
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 63
http://www.tesda.gov.ph/downloads/default.asp / secjr
6. unusual problems Unusual problems may include:
6.1 conflict with other parties:
6.1.1. government national and local regulations
6.1.2. owner of subject vegetation that needs to be trimmed
6.1.3. installation of other utility companies affecting the
CATV cable lines
6.2 accidents and unforeseen incidents
6.3 Situations arising from poor peace and order conditions
6.4 Poles that needs to be replaced or relocated
7. concerned This may include:
personnel 7.1 supervisors and/or owner of CATV facilities
7.2 town/barangay officials
7.3 homeowner association officials
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 48
http://www.tesda.gov.ph/downloads/default.asp / secjr
30. UHF – Ultrahigh frequency. The band of frequencies extending from 470 to 890 MHz as
designated by the Federal Communications Commission.
31. VHF – Very high frequency. The band extending from 30 to 300 MHz.
32. Wiring systems - Permitted cables, enclosures, supports and accessories for power,
measurement, control or communications purposes.
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 65
http://www.tesda.gov.ph/downloads/default.asp / secjr
ANNEX A - ICT (BROADCAST MEDIA) COMPETENCY MAP
BASIC COMPETENCIES
Receive and
Practice basic Participate in
Respond to Demonstrate work
Work with Others housekeeping Workplace
Workplace values
procedures Communication
Communication
Practice occupational
Work in a Team Practice career Lead Workplace
health and safety Lead Small Team
Environment professionalism Communication
procedures
COMMON COMPETENCIES
Terminate and
Connect Electrical
Wiring and Electronic
Circuits
CORE COMPETENCIES
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 66
http://www.tesda.gov.ph/downloads/default.asp / secjr
ACKNOWLEDGEMENTS
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TRAINING REGULATIONS – CATV OPERATION & MAINTENANCE NC III Promulgated December 2007 Page 67
http://www.tesda.gov.ph/downloads/default.asp / secjr