Professional Documents
Culture Documents
Product Catalog & Design Guide: Gas Discharge Tube (GDT) Products
Product Catalog & Design Guide: Gas Discharge Tube (GDT) Products
CATALOG
& DESIGN
GUIDE
RoHS Compliant
Breakover Max AC Peak Pulse Operating
Cartridge Clip
Series Max
Radial Lead
# Terminals
Axial Lead
Voltage Surge Current Temperature
Lead Free
Mini Tube
Name1 Capacitance
Surface
Range Rating (8x20µs) Range
(Nom VBO)
High Voltage GDTs
-40°C to +90°C
AC 285 - 600 5000A 1.5pF 2 • •
NA
CG3 1000 - 7500 5000A 1.5pF 2 • •
Squared GDTs
SE 140 to 500 0.5KA 0.5pF 2 • •
(1) Please refer to product data in our datasheets for detailed information by part number.
© 2017
2017 Littelfuse,
Littelfuse, Inc.
* Total current through center (ground) terminal
Specifications are
Specifications, subject toand
descriptions change without
illustrative notice.in this literature are
material
as accurate
Revised: as known at the time of publication, but are subject to change
12/12/17
without notice. Visit www.littelfuse.com for more information.
Gas Discharge Tubes
Voltage (V)
as the air gap. Carbon block protectors are used mainly for
Voltage
telephone line protection but are being replaced, in most
installations, with the more reliable and consistent gas
discharge tubes.
Voltage (V)
can begin to conduct. This trigger signal is usually supplied referred to as transient voltage suppressers (TVS) diodes.
through the use of a zener diode. Packages that combine These diodes consist of fairlyBreakdown
large junction zeners which
the SCR and zener diode are now available. These packages have been designed specifically Voltage
for surge protection. The
TVS diodes are rated for higher current surges than zener
are monolithic devices and often contain an SCR-type Zener
thyristor with a gate region that acts like the avalanche diodes and they Voltage
can carry these currents for periods of 2-10
diode. Once triggered, the SCR begins to conduct, dropping microseconds.
the voltage across the zener diode to a value below the
130 are required. These
For use in AC signal lines, two zeners
zener’s operating voltage and thus causing the zener to stop
are available as packagedCurrent
devices. Avalanche diodes are
(mA)
conducting. The SCR will conduct until the applied voltage
often used to protect IC’s from static discharge and other
drops to zero (zero crossing of AC) or until the current falls
forms of transients in power supplies computer buses, and
below a specified value (sometimes referred to as a holding
data lines.
current).
SCR Avalanche Diode
Voltage vs. Current Characteristics Voltage vs. Current Characteristics
Leakage
Region
Clamping
Voltage (V)
Voltage (V)
Voltage
Breakdown
Voltage
Zener
Voltage
130 .001
Although typically having a faster response time than a MOV (METAL OXIDE VARISTOR): As its name
GDT, the SCR package is subject to higher leakage current suggests, the MOV is a voltage variable resistor made
Avalanche
and capacitance. The Diode
SCR package can handle currents from sintered metal oxides. The grains produced in the
Voltage
of several vs.amperes
hundred CurrentofCharacteristics
an 8/20 wave form and sintered metal oxide material of the MOV can be thought
packages are available that offer bi-directional protection. of as a network of series and parallel diodes. As the voltage
potential across the MOV increases, some of the diodes
CLAMPING PROTECTION: A clamping device actually experience avalanche breakdown and begin to conduct and
limits the voltage transient to a specified level by varying
Leakage
through the device increases, the voltage which the MOV plating and the final seal is made in a gasfilled vacuum
clamps at is greatly increased. furnace using braze preforms made of copper-silver eutectic.
The electrodes used for GDTs are either copper or a nickel-
MOV iron alloy, often with a coating to lower the work function
Voltage vs. Current Characteristics and/or add gettering capability. Stripes or bands of semi-
conductive material are applied to the inner surfaces of the
ceramic to improve stability and high-speed response.
Region
Upturn
In contrast, most devices in Littelfuse’s High Energy Devices
Leakage
Region
Voltage (V)
Volts
ARIZED COMPARISON
of the keyOF TECHNOLOGIES
performance parameters for every application.
Due to their complementary performance characteristics,
however, aGAS
GDTTUBE
and MOV can beSCR MOV
combined in a circuit to DIODE
provide theCG2-230L
ultimate in surge suppression performance. The A'
The CLARE product engineering department provides objective technical expertise and
application assistance to designer’s of switching surge protection systems. Our mission is
to assist you in designing the best solution to your specific application problem, regardless
manufacturer. To access our team of engineering professionals call toll free 1-800
CPCLARE.
THEORY
The basic operation of gas tube surge arrestors such as
Littelfuse’s GDTs is best understood by referring to the
schematic form of the voltage-current (V-i) relationship of a
generic gas discharge device such as the one depicted in
Figure 1.
G The arc region. In this region, the arc voltage will quickly
drop and the arc current will quickly increase within the
limitations of the drive energy and impedance.
Legal Disclaimers
Liability Disclaimer
Littelfuse, Inc. its affiliates, agents, and employees, Specifications, descriptions and data contained in this
and all persons acting on its or their behalf (collectively, document are believed to be accurate. However, users
“Littelfuse”), disclaim any and all liability for any errors, should independently evaluate each product for the
inaccuracies or incompleteness contained here or in any particular application. Littelfuse reserves the right to
other disclosure relating to any product. Littelfuse disclaims change any information contained herein without notice
any and all liability arising out of the use or application and may, at its sole discretion, change the design,
of any product described herein or of any information manufacture or construction of any product. Visit
provided herein to the maximum extent permitted by law. www.littelfuse.com for the most up-to-date information.
The product specifications do not expand or otherwise Littelfuse’s only obligations for any of its products are
modify Littelfuse terms and conditions of purchase, specified in its Standard Terms and Conditions and
including but not limited to the warranty expressed therein, Littelfuse shall not be liable for any indirect, consequential
which apply to these products. or incidental damages from any sale or use of any of its
products.
Right to Make Changes
Intellectual Property
Description
E320116 Features
Electrical Characteristics
Note:
* Insulation resistance measured at:
• 250Vdc for CG40.8,
• 500Vdc for CG41.0 8, CG41.0, CG41.8 and CG42.0,
• 1000Vdc for CG42.5, CG42.7 and CG43.0
Product Characteristics
Dimensions in millimeters
6.2 ± 0.2
3.5 ± 0.2
2
0.
±
0
6.
4.2 ± 0.2
TOP VIEW
Part Numbering System and Ordering Information
1.3
CG4 x.x SM
7.2
Series
CG4
3.5
Breakdown Voltage
Recommended Soldering Pad Layout 0.8 = 800V
1.0 = 1000V
3.0 = 3000V
(Voltage code examples for x.x)
100 Typ.
18 Typ.
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete
Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.
© 2017 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 12/12/17
Gas Discharge Tubes
AC and CG3 Series
Description
AC Series:
• Long branch circuits • Power supplies
(AC wall outlet) • Test equipment
• Short branch circuits • Submersible pumps
(at breaker box,
• Medical electronics
Additional Information computer, etc)
CG3 Series:
• CRT terminals • Power supplies
• CATV equipment • Medical electronics
Datasheet Resources Samples
AC Series AC Series AC Series • Antennas
Electrical Characteristics
DC Breakdown Impulse Impulse Insulation Capaci- Arc Max Nominal AC Nominal Max
in Volts Break- Break- Resistance tance Voltage Follow AC Discharge Impulse Surge
(@100V/s) down down In (@1MHz) (on state On Discharge Current Discharge Current5
in Volts Volts Voltage) Current3 Current (1 x 50Hz Current4 (@8/20µs)
@1Amp Min (10x1sec 9 cycles)
(@100V/µs) (@1 Kv/µsec) (@8/20µs)
@50-60Hz)
Part
Number MIN TYP MAX MAX MIN MAX TYP
AC1201 A 230 285 340 500 550 10 GΩ 200 10 shots 1 shot
<1.5 pf ~ 25 V 5A 65 A
AC2401 A 480 600 720 1100 1200 (at 100V) Amps 5kA 10kA
CG3 1.01 A 800 1000 1200 1400 1500
CG3 1.11 A 880 1100 1320 1600 1700
CG3 1.21 A 960 1200 1440 1700 1800
CG3 1.31 A 1040 1300 1560 1800 1900
CG3 1.51 A 1200 1500 1800 1800 2000
CG3 2.01 A 1600 2000 2400 2500 2750
CG3 2.51 A 2000 2500 3000 3200 3500
CG3 2.71 A 2160 2700 3240 3600 4000 10 GΩ 200 10 shots 1 shot
<1.5 pf ~ 25 V N/A N/A
CG3 3.01 A 2400 3000 3600 4000 4200 (at 100V) Amps 5kA 10kA
CG3 3.31 A 2640 3300 3960 4600 4700
CG3 4.0 2
B 3200 4000 4800 5800 6000
CG3 4.52 B 3600 4500 5400 6150 6500
CG3 5.02 B 4000 5000 6000 7500 8000
CG3 6.22,7 B 4960 6200 7440 8100 9500
CG3 6.52,7 B 5200 6500 7800 9500 10000
CG3 7.52,6,7 B 6000 7500 9000 10000 10600
NOTES:
1. Refer to Production Dimensions section, outline A devices
2. Refer to Production Dimensions section, outline B devices Product Characteristics
3. Tested to UL1449 -- 120V r.ms. for AC120, 230V r.m.s. all others.
Conducted with suitable MOV connected in series.
4. 10 x [5(+) and 5(-)] applications 5kA @ 8/20µs Core Outline A & B items:
5. 1 x [1(+) and 1(-)] application 10kA @ 8/20µs Device: Tin Plated 17.5±12.5 Microns
6. CG3 7.5 product UL approval is currently pending Materials
Axial Outline A & B items:
7. When ordering this item, use suffix code D004 when entering the part number.
The older product version without D004 suffix code has been discontinued.
Device & Wire: Tin Plated 17.5±12.5 Microns
Refer to Part Numbering System section for additional information.
LF Logo, Voltage and date code;
Product Marking
Black ink positive print
Glow to arc
< 0.5Amps
transition current
Glow Voltage ~ 140 Volts
Storage and
Operational -40 to +90
Temperature
Temperature
- Time (Min to Max) (ts) 60 – 180 secs
Ramp-down
Average ramp up rate (Liquidus Temp
3°C/second max Preheat
(TL) to peak TS(min)
tS
TS(max) to TL - Ramp-up Rate 5°C/second max
- Temperature (TL) (Liquidus) 217°C 25
Reflow
- Temperature (tL) 60 – 150 seconds time to peak temperature
(t 25ºC to peak) Time
Peak Temperature (TP) 260+0/-5 °C
Time within 5°C of actual peak
10 – 30 seconds
Temperature (tp)
Ramp-down Rate 6°C/second max
Time 25°C to peak Temperature (TP) 8 minutes Max.
Do not exceed 260°C
180
Temperature Minimum: 100° C
160 Temperature Maximum: 150° C
140
Preheat Time: 60-180 seconds
120
100
Solder Pot Temperature: 280° C Maximum
80
20
0
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
10
20
30
40
50
60
70
80
90
0
Time (Seconds)
Axial PROFILE VIEW TOP VIEW AC XXX XXX CG3 X.X XXX D004
Series Series
0.80DIA. TYP. CG3
[0.031] AC Line Voltage Breakdown Voltage
120 = 120V
A 8.0 ± 0.2
[0.314 ± 0.008]
240 = 240V
1.0 = 1000V
1.1 = 1100V
1.2 = 1200V
Lead / Packaging Option 1.3 = 1300V
= Core (no leads) / Bulk pack, 400 pcs per bag 1.5 = 1500V
L = Leaded / Bulk pack, 50 pcs per tray 2.0 = 2000V
6.0 ± 0.2 LTR = Leaded / Tape & Reel, 500 pcs per reel 2.5 = 2500V
[0.236 ± 0.008]
2.7 = 2700V
62 ± 2 3.0 = 3000V
[2.441 ± 0.079] 3.3 = 3300V
4.0 = 4000V
4.5 = 4500V
7.9 ± 0.3
[0.311 ± 0.012] 5.0 = 5000V
6.2 = 6200V
6.5 = 6500V
7.5 = 7500V
8.0 ± 0.2
B [0.314 ± 0.008] Lead / Packaging Option
= Core (no leads) / Bulk pack, 400 pcs per bag
0.80DIA. TYP. L = Leaded / Bulk pack, 50 pcs per tray
[0.031] LTR = Leaded / Tape & Reel, 500 pcs per reel
<1.2 Max. Lead Bend
Special Suffix Code
SEMI–PROFILE VIEW Enter this D004 special suffix code when placing orders
for CG36.2, CG36.5 and CG37.5 only
Core PROFILE VIEW TOP VIEW
A 8.0 ± 0.2
[0.314 ± 0.008]
<0.8 Max
52.4
6.0 ± 0.2 [2.063]
[0.236 ± 0.008]
22.8
[0.898]
B 8.0 ± 0.2
[0.314 ± 0.008]
6.4
[0.252]
7.9 ± 0.3 5.0 Pitch
[0.311 ± 0.012]
[0.197]
Packaging Dimensions
For 'LTR' Option Code Axial Lead Items <1.2 Max. Lead Bend
254.0 - 356.0
[10.0 - 14.0]
<0.8 Max
22.8
[0.898]
6.4
[0.252]
5.0 Pitch
[0.197]
254.0 - 356.0
[10.0 - 14.0]
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete
Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.
Direction of Feed © 2017 Littelfuse, Inc.
80.0
[3.15] Specifications are subject to change without notice.
Revised: 12/12/17
Gas Discharge Tubes
CG7 Series
Description
E128662
Features
E320116 • RoHS compliant and • 1kA 8/20μS surge
Lead-free capability pulse as
• Excellent Surge defined by IEC 61000-
Two Electrode GDT Graphical Symbol
Withstanding Capability 4-5 2nd edition
• Excellent response to • Ultra Low capacitance
fast rising transients. (<0.3pF)
• Ultra Low Insertion • Voltage Range 75V
Loss and low off-state to 470V
capacitance for GHz • UL recognized
bandwidth compatibility
Additional Information • Ultra small devices
offered in SMD package
Electrical Characteristics
Notes:
UL Pending for CG775 and CG7470.
1. 5 x (+) and 5 x (-) applications of 1kA 8/20μs sec.
Typical Insertion Loss
2. 5 x (+) and 5 x (-) applications of 100A 10/700μs sec.
@1.0GHz = 0.02dB
Product Characteristics @1.4GHz = 0.03dB
@1.8GHz = 0.05dB
Device Tin Plated 17.5 ± 12.5
Materials Microns @2.0GHz = 0.06dB
Construction: Ceramic Insulator
@2.4GHz = 0.07dB
Storage and Operational
-40 to +90°C @2.8GHz = 0.08dB
Temperature
@3.1GHz = 0.09dB
@3.5GHz = 0.10dB
Voltage Vs. Time Characteristic
@4.0GHz = 0.12dB
Note: Insertion data for customer reference only, application testing needed for verification.
Max dynamic
800 breakover voltage
Arc Voltage
Point at which gas tube is at
400 I Axis lowest impedance and
fully conductive.
Hold over voltage Typical arc voltage at about
10 to 12 Volts
200
V Axis
Temperature
- Time (Min to Max) (ts) 60 – 180 secs
Ramp-down
Average ramp up rate (Liquidus Temp
3°C/second max Preheat
(TL) to peak TS(min)
tS
TS(max) to TL - Ramp-up Rate 5°C/second max
- Temperature (TL) (Liquidus) 217°C 25
Reflow
- Temperature (tL) 60 – 150 seconds time to peak temperature
(t 25ºC to peak) Time
Peak Temperature (TP) 260 +0/-5
°C
Time within 5°C of actual peak
10 – 30 seconds
Temperature (tp)
Ramp-down Rate 6°C/second max
Time 25°C to peak Temperature (TP) 8 minutes Max.
Do not exceed 260°C
Dimensions in millimeters
Unit = mm
Item Spec Item Spec
P2 P0 P
E D
P 8.0 ± 0.1 E 1.75 ± 0.1
>1.5
Packaging Quantity:
2500 pcs per reel (13”)
100 Typ.
1 reels per inner box
10 inners box per carton
25,000 pcs per full carton
15 Typ.
CG7 XXX MS
Series
CG7
Breakdown Voltage
70 = 70V
90 = 90V
120 = 120V
150 = 150V
200 = 200V
230 = 230V
350 = 350V
400 = 400V
470 = 470V
Surface Mount
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete
Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.
© 2017 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 12/12/17
Gas Discharge Tubes
CG6 Series
Description
E128662
Features
E320116 • RoHS compliant and • Compact SMD package
Lead-free offered in two squared
Two Electrode GDT Graphical Symbol • Excellent Surge terminals
Withstanding Capability • Non-Radioactive
• Excellent response to • Ultra Low capacitance
fast rising transients. (<0.3pF)
• Ultra Low Insertion • Voltage Range 75V to
Loss and low off-state 600V
capacitance for GHz • UL recognized
bandwidth compatibility
• Characterized according
Additional Information • 3kA 8/20µs surge to ITU-T K.12 as a Class
capability X, Type 1 GDT
Applications
Datasheet Resources Samples
CG5 Series • Broadband equipment • Embedded Multimedia
• CATV/Broadband Terminal Adapter
equipment (EMTA)
• Data lines and Ethernet • RF Connector
(up to 10GbE) • Multimedia over Coax
• xDSL equipment, Alliance (MoCA)
including ADSL2, ADSL, • Base Station RF
VDSL, VDSL2 30a antenna transmitter
bandplan compatible • G.Fast 106MHz and
• IAD (Integrated Access 212 MHz bandplans
Device) compatible
• Set Top Box (STB) • Aerospace and
• General telecom Automotive
equipment
Electrical Characteristics
Note:
1. 5 x (+) and 5 x (-) applications of 3kA 8/20μs sec.
2. 5 x (+) and 5 x (-) applications of 150A 10/700μs sec. Typical Insertion Loss
@1.4GHz = 0.06dB
@2.4GHz = 0.13dB
Storage and Operational
-40 to +90°C
Temperature @2.8GHz = 0.15dB
@3.1GHz = 0.17dB
@3.5GHz = 0.19dB
Voltage Vs. Time Characteristic
@4.0GHz = 0.22dB
Max dynamic Note: Insertion data for customer reference only, application testing needed for verification.
800 breakover voltage
Arc Voltage
Point at which gas tube is at
400 I Axis lowest impedance and
fully conductive.
Typical arc voltage at about
Hold over voltage 10 to 12 Volts
200
V Axis
On-state voltage
Temperature
- Time (Min to Max) (ts) 60 – 180 secs
Ramp-down
Average ramp up rate (Liquidus Temp
3°C/second max Preheat
(TL) to peak TS(min)
tS
TS(max) to TL - Ramp-up Rate 5°C/second max
- Temperature (TL) (Liquidus) 217°C 25
Reflow
- Temperature (tL) 60 – 150 seconds time to peak temperature
(t 25ºC to peak) Time
Peak Temperature (TP) 260 +0/-5
°C
Time within 5°C of actual peak
10 – 30 seconds
Temperature (tp)
Ramp-down Rate 6°C/second max
Time 25°C to peak Temperature (TP) 8 minutes Max.
Do not exceed 260°C
Dimensions in millimeters
3.5 ± 0.2
Unit = mm
Item Spec Item Spec
P2 P0 P
E D
P 8.0 ± 0.1 E 1.75 ± 0.1
>1.5
Packaging Quantity:
2000 pcs per reel (13”)
100 Typ.
1 reels per inner box
10 inners box per carton
20,000 pcs per full carton
15 Typ.
CG6 XXX SM
Series
CG6
Breakdown Voltage
75 = 75V
90 = 90V
145 = 145V
230 = 230V
250 = 250V
300 = 300V
350 = 350V
400 = 400V
470 = 470V
600 = 600V
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete
Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.
© 2017 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 12/12/17
Gas Discharge Tubes
CG5 and SL0902A Series
Description
Electrical Characteristics
Product Characteristics
CG5xxxLS (Outline 500), CG5xxxxLTR Product Marking LF Logo, Voltage and date code
& CG5350L-03TR (Outline 502), and
CG5xxxL-02 (Outline 503): Device Glow to arc
< 0.5Amps
Nickel Plated 2–5 Microns Wire Tin Plated transition current
17.5±12.5 Microns Construction Ceramic
Materials
Insulator. Glow Voltage 140 Volts
CG5xxx (Outline 501), and CG5xxxMS
& SL0902AxxxSM (Outline 505): Storage and
Device Tin Plated 17.5±12.5 Microns Operational -40 to +90
Construction Ceramic Insulator. Temperature
@ 2.45 GHz= 1 dB
(V)
Device Dimensions
Outline 500 - CG5xxxLS Outline 503 - CG5xxxL-02 (except CG5600L-02, see Outline 502)
5.0 ± 0.2
[0.197 ± 0.008]
40° ± 3°
5.30 ± 0.30
[0.209 ± 0.012]
3.0 ± 0.3 5.0 ± 0.2
[0.118 ± 0.008] [0.197 ± 0.008]
0.80
0.004 5.30 ± 0.30 [0.031] 0.80DIA. TYP.
2 Surfaces 0.40 ± 0.03 [0.209 ± 0.012] 6.3 ± 0.2 [0.031]
[0.016 ± 0.0012] [2.480 ± 0.079]
8.00 ± 0.30
[0.315 ± 0.012]
9.30 ± 0.30
[0.366 ± 0.012]
Outline 505 - CG5xxxMS and SL0902AxxxSM
SOLDER PAD LAYOUT
PROFILE VIEW TOP VIEW
8.00
[0.315] 6.6 ± 0.2
[0.260 ± 0.008]
5.50
[0.216]
5.4 ± 0.15
[0.212 ± 0.006]
1.80
[0.071]
0.5 ± 0.1
9.80 [0.02 ± 0.004 ] 3.8
[0.386] [0.15]
5.0 ± 0.2 5.4 ± 0.15
[0.197 ± 0.008] [0.212 ± 0.006]
5.10
5.0 ± 0.15 [0.2]
[0.197 ± 0.006]
0.70
[0.028]
5.0 ± 0.2
[0.197 ± 0.008]
5.0 ± 0.2
[0.197 ± 0.008]
62 ± 2
[2.441 ± 0.079]
Temperature
- Time (Min to Max) (ts) 60 – 180 secs
Ramp-down
Average ramp up rate (Liquidus Temp
3°C/second max Preheat
(TL) to peak TS(min)
tS
TS(max) to TL - Ramp-up Rate 5°C/second max
- Temperature (TL) (Liquidus) 217°C 25
Reflow
- Temperature (tL) 60 – 150 seconds time to peak temperature
(t 25ºC to peak) Time
Peak Temperature (TP) 260+0/-5 °C
Time within 5°C of actual peak
10 – 30 seconds
Temperature (tp) Soldering Parameters - Hand Soldering
Ramp-down Rate 6°C/second max
Solder Iron Temperature: 350° C +/- 5°C
Time 25°C to peak Temperature (TP) 8 minutes Max. Heating Time: 5 seconds max.
Do not exceed 260°C
180
Temperature Minimum: 100° C
160 Temperature Maximum: 150° C
140
Preheat Time: 60-180 seconds
120
100
Solder Pot Temperature: 280° C Maximum
80
110
120
130
140
150
160
170
180
190
200
210
220
230
240
10
20
30
40
50
60
70
80
90
0
Time (Seconds)
Packaging
CG5xxxLTR
Straight Axial Leads Outline 502 1000pcs/reel in tape and reel*
CG5xxxL-03TR**
CG5xxxL-02** Bent Radial Leads Outline 503 50pcs/tray in tray and cover
CG5xxxMS
Surface mount Outline 505 900pcs/reel in carrier and tape*
SL0902AxxxSM
* For tape specifications and dimensions, please contact factory.
** Special order items not available for general sale. Please contact Littelfuse for details.
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete
Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.
© 2017 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 12/12/17
Gas Discharge Tubes
SL1002A Series
Description
The Broadband Optimized™ SL1002A series has
been especially developed for use in broadband
equipment. Special design features provide high
levels of protection against fast rising transients
in the 100V/μs to 1kV/μs range usually caused by
lightning disturbances. These devices have ultra low
capacitance (typically 1.2pF or less) and present
insignificant signal losses up to 1.5GHz. These
devices are extremely robust and are able to divert
a 5000A pulse without destruction. For AC Power
Cross of long duration, overcurrent protection is
recommended.
Agency Approvals
Features
AGENCY AGENCY FILE NUMBER
• RoHS compliant/Lead- • 10/700 6kV capability,
E128662 free as per ITU-T Rec. K.21,
• Ultra low insertion loss enhanced test level
2 Electrode GDT Graphical Symbol • Surface mountable • 2000 A 2/10μs surge
rating
• 5kA surge capability
tested with 8/20μS– • Meet FCC part 68
Pulse as defined by IEC 10/160μs waveform,
61000-4-5 200A test and 10/560μs
waveform 100A test
• Excellent response to
fast rising transients • Halogen-free
Electrical Characteristics
Notes:
1. At delivery AQL 0.65 level II, DIN ISO 2859
2. In ionized mode
3. In ionized mode, tested according to ITU-T Rec. K.12
4. Comparable to the silicon measurement Switching Voltage (Vs)
5. Reference REA PE-80, 0.2A. Tested to ITU-T Rec. K.12 and REA PE-80 < 150 msecs.
6. 300 Applications [150(+) & 150(-)]
7. 10x[5x (+) & 5x (-)] Applications
Product Characteristics
Max dynamic
breakover voltage
Voltage
(V)
Hold-over voltage
On-State voltage
Typical Insertion Loss Characteristics (90V) Typical Insertion Loss Characteristics (600V)
2 2
0 0
-2
-2
-4
-4
-6
S21 [dB]
S21 [dB]
-6
-8
-8
-10
-10
-12
-12
-14
-16 -14
-18 -16
1.E+07 1.E+08 1.E+09 1.E+10 1.E+11 1.E+07 1.E+08 1.E+09 1.E+10 1.E+11
Frequency [Hz] Frequency [Hz]
Device Dimensions
Ø6.2 ± 0.15
0.50
7.
0.50
5
±
0.
2
1.30 [0.051]
5.00 [0.197]
3.50 [0.138]
Temperature
- Time (Min to Max) (ts) 60 – 180 seconds
Ramp-down
Average Ramp-up Rate (Liquidus Temp
3°C/second max. Preheat
(TL) to peak) TS(min)
tS
TS(max) to TL - Ramp-up Rate 5°C/second max.
- Temperature (TL) (Liquidus) 217°C 25
Reflow
- Temperature (tL) 60 – 150 seconds time to peak temperature
(t 25ºC to peak) Time
Peak Temperature (TP) 260+0/-5 °C
Time within 5°C of Actual Peak
10 – 30 seconds
Temperature (tp)
Ramp-down Rate 6°C/second max.
Time 25°C to Peak Temperature (TP) 8 minutes max.
Do not exceed 260°C
120
Preheat Time: 60-180 seconds
100
Solder Pot Temperature: 280° C Maximum
80
20
0
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
10
20
30
40
50
60
70
80
90
0
Time (Seconds)
Packaging
‘C’ Type Core Items: Package bulk pack in polybag, 1000 pcs/bag
'SM' Type Surface Mount Items: Packaged tape and reel carrier, 1000 pcs/reel (specifications below)
Dimensions are in millimeters [and inches] Dimensions are in millimeters [and inches]
6.5 ± 0.1
275.0
1.50 +0.10 [0.256 ± 0.004] [10.83]
0
0.40
[0.059 +0.004 ] [0.016] 100.0
0
[3.94]
3°
76.0
[0.256 ± 0.004]
[2.99]
[0.630 ± 0.012]
25.0
6.5 ± 0.1
16 ± 0.3
[0.98]
[0.295 ± 0.004]
7.5 ± 0.1
R0.30 max.
[0.012] 17.7
[0.697]
1.50 2 ± 0.1 8 ± 0.1 [0.069 ± 0.004]
1.75 ± 0.1
Direction of Feed
[0.059] [0.079 ± 0.004] [0.315 ± 0.004]
10x4=40 ± 0.2 4 ± 0.1
[10x0.157=1.575 ± 0.008] [0.157 ± 0.004]
SL1002 A XXX XX
Surge Capability
Voltage
Pin Configuration
C = Core (Packed in polybag, 1000pcs/bag)
SM = Surface Mount (Packed in carrier and tape, 1000pcs/reel)
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete
Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.
© 2017 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 12/12/17
Gas Discharge Tubes
SL1003A Series
Description
The SL1003A series has been especially developed
for Broadband equipment. Special design features
provide high levels of protection against fast rising
transients in the 100V/μs to 1kV/μs range usually
caused by lightning disturbances.
Electrical Characteristics
Notes:
1. At delivery AQL 0.65 level II, DIN ISO 2859
2. In ionized mode, tested according to ITU-T Rec. K.12
3. Comparable to the silicon measurement Switching Voltage (Vs)
4. Reference REA PE-80, 0.2A. Tested to ITU-T Rec. K.12 and REA PE-80 < 150 msecs.
Product Characteristics
Device Dimensions
'R' Type Radial Lead Devices (SL1003AxxxR-001) 'C' Type Core Devices
'R' Type Radial Lead Devices (SL1003AxxxR and SL1003AxxxRF) 'SM' Type Surface Mount Devices
PROFILE VIEW TOP VIEW
TOP VIEW
12.2 - 2 6.0 ± 0.1 PROFILE VIEW
[0.480 - 0.079] [0.236 ± 0.039]
6.0 ± 0.1 8.1 ± 0.2
8.1 ± 0.2
3.20 [0.319 ± 0.0079]
[0.236 ± 0.039] [0.126] 2.8 2.8
[0.110] [0.110]
Ø6.0 ± 0.1
1.5
[0.059]
2.20
[0.087]
1.20 1.20
PROFILE VIEW TOP VIEW
[0.04] [0.047]
12.2 - 2 6.0 ± 0.1
[0.480 - 0.079] [0.236 ± 0.039]
1.2 Max 8.1 ± 0.2 7.00
[0.047] [0.236 ± 0.039]
[0.275]
6.000 allow space
[0.236] for product
clearance
6.7 ± 0.5
[0.263 ± 0.020]
2.10 2.10
[0.083] [0.083]
6.40
4.3 + 1.5 6.0 ± 0.5 [0.252]
[0.169 + 0.059] [0.236 ± 0.020]
7.60
[0.299]
Temperature
- Time (Min to Max) (ts) 60 – 180 seconds
Ramp-down
Average Ramp-up Rate (Liquidus Temp
3°C/second max. Preheat
(TL) to peak) TS(min)
tS
TS(max) to TL - Ramp-up Rate 5°C/second max.
- Temperature (TL) (Liquidus) 217°C 25
Reflow
- Temperature (tL) 60 – 150 seconds time to peak temperature
(t 25ºC to peak) Time
Peak Temperature (TP) 260+0/-5 °C
Time within 5°C of Actual Peak
10 – 30 seconds
Temperature (tp)
Ramp-down Rate 6°C/second max.
Time 25°C to Peak Temperature (TP) 8 minutes max.
Do not exceed 260°C
120
Preheat Time: 60-180 seconds
100
Solder Pot Temperature: 280° C Maximum
80
20
0
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
10
20
30
40
50
60
70
80
90
0
Time (Seconds)
Packaging
'C' Type Core Items: Package bulk pack in polybag, 500 pcs/bag
'R' and ‘RF’ Type Radial Lead Items: Packed in tray, 100 pcs/tray
'SM' Type Surface Mount Items: Packaged tape and reel carrier, 700 pcs/reel (specifications below)
Dimensions are in millimeters [and inches] Dimensions are in millimeters [and inches]
[0.069 ± 0.0039]
[3.94]
m
76.0
20°
[0.453 ± 0.0039]
[2.99] 25.0
11.5 ± 0.1
[0.98]
[ 0.945 ± 0.012]
[0.339 ± 0.0039]
24 ± 0.3
14 [0.551]
4 [0.157]
8.6 ± 0.1
17.7
[0.697]
Direction of Feed
5° m
[0.118] [0.354]
6.1 ± 0.1
R0.3 typical [0.240 ± 0.0039]
[0.012]
SMD-tape according to IEC 60286-3
SL1003 A XXX XX
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete
Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.
© 2017 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 12/12/17
Gas Discharge Tubes
SL1010A Series
Description
The SL1010A Series Gas Discharge Tube (GDT) offers
a compact, three-terminal, surface mount component
that’s just 5mm in diameter. It is rated for 10 hits
(±5 repetitions) of a 5kA 8/20µs surge event with a
low off-state capacitance of 1.5pF. Its low arc voltage
parameter of 10V reduces thermal accumulation
during long-term power fault events.
Agency Approvals
Features
AGENCY AGENCY FILE NUMBER • 5mm diameter size • High current rating
• Low insertion loss • Stable performance
E128662
• Fast response time over lifetime
• Single component • Lead-free and RoHS
3 Electrode GDT Graphical Symbol balanced protector compliant
(T-grd & R-grd) • UL Recognized
Applications
Electrical Characteristics
Product Characteristics
Product Marking Littelfuse 'LF' Mark, voltage and date code Storage and Operational Temperature -40 to +90°C
Device Dimensions
For SL1010A series: Dimensions are in millimeters [and inches]
0,2
4,7
2
0,
6
Temperature
Pre Heat - Temperature Max (Ts(max)) 200°C
- Time (Min to Max) (ts) 60 – 180 seconds Ramp-down
Preheat
Average Ramp-up Rate (Liquidus Temp TS(min)
3°C/second max.
(TL) to peak) tS
TS(max) to TL - Ramp-up Rate 5°C/second max.
25
- Temperature (TL) (Liquidus) 217°C time to peak temperature
Reflow (t 25ºC to peak) Time
- Temperature (tL) 60 – 150 seconds
Peak Temperature (TP) 260+0/-5 °C
Soldering Parameters - Hand Soldering
Time within 5°C of Actual Peak
10 – 30 seconds
Temperature (tp) Solder Iron Temperature: 350° C +/- 5°C
Ramp-down Rate 6°C/second max. Heating Time: 5 seconds max.
Time 25°C to Peak Temperature (TP) 8 minutes max.
Do not exceed 260°C
Packaging
'SM' Type Surface Mount Items: Packaged tape and reel carrier, 900 pcs/reel (specifications below)
Dimensions are in millimeters [and inches] Dimensions are in millimeters [and inches]
275.0
[10.83]
100.0
[3.94]
76.0
[2.99] 25.0
[0.98]
17.7
[0.697]
Direction of Feed
SL1010A Series
Voltage
Pin Configuration
F = with Failsafe (Packed in carrier and tape, 900pcs/reel)
SM = Surface Mount (Packed in carrier and tape, 900pcs/reel)
SMF = Surface Mount with Failsafe (Packed in carrier and tape, 900pcs/reel)
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete
Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.
© 2017 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 12/12/17
Gas Discharge Tubes
SL1011A and SL1411A Series
Description
The SL1011A and SL1411A series provides high levels
of protection against fast rising transients in the
100V/µs to 1kV/µs range usually caused by lightning
disturbances.
Features
AGENCY AGENCY FILE NUMBER
• Lead-free and RoHS • 5kA (SL1011A) or
E128662 compliant 10kA (SL1411A) surge
• Low insertion loss capability tested with
2 Electrode GDT Graphical Symbol 8/20μs pulse as defined
• Excellent response to
by IEC 61000-4-5 2nd
fast rising transients
edition
• Ultra low capacitance
Applications
Electrical Characteristics
Product Characteristics
Device Dimensions
Ø8.0 ± 0.2
[0.315 ± 0.0079]
Ø8.0 ± 0.2
6.05 ± 0.2
[0.238 ± 0.0079]
62 ± 2
'A' Type Axial Lead Devices 'SM' Type Surface Mount Devices
PROFILE VIEW TOP VIEW TOP VIEW PROFILE VIEW SEMI–PROFILE VIEW
8.3 ± 0.1
Ø1.0 4 [0.157]
[0.039] 5.55 [0.219]
+ 0.10 6.05 ± 0.2
Ø8.0 – 0.30
[0.238 ± 0.0079]
[0.315 + 0.0039
– 0.0118 ]
Ø8.3 ± 0.15
6.05 ± 0.2
[0.238 ± 0.0079]
62 ± 2
Ø
9.
0.5 ± 0.1
30
±
0.
1.30 [0.051]
7.00 [0.276]
Temperature
- Time (Min to Max) (ts) 60 – 180 seconds
Ramp-down
Average Ramp-up Rate (Liquidus Temp
3°C/second max. Preheat
(TL) to peak) TS(min)
tS
TS(max) to TL - Ramp-up Rate 5°C/second max.
- Temperature (TL) (Liquidus) 217°C 25
Reflow
- Temperature (tL) 60 – 150 seconds time to peak temperature
(t 25ºC to peak) Time
Peak Temperature (TP) 260+0/-5 °C
Time within 5°C of Actual Peak
10 – 30 seconds
Temperature (tp)
Ramp-down Rate 6°C/second max.
Time 25°C to Peak Temperature (TP) 8 minutes max.
Do not exceed 260°C
120
Preheat Time: 60-180 seconds
100
Solder Pot Temperature: 280° C Maximum
80
20
0
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
10
20
30
40
50
60
70
80
90
0
Time (Seconds)
22.8
[0.898]
6±1
[0.236 ± 0.039]
10 ± 0.5 Pitch
[0.394 ± 0.020]
Packaging Dimensions
254.0 - 356.0
[10.0 - 14.0]
22.8
[0.898]
6±1
[0.236 ± 0.039]
10 ± 0.5 Pitch
[0.394 ± 0.020]
275.0
254.0 - 356.0 [10.83]
[10.0 - 14.0]
10x4 ± 0.1 = 40 ± 0.2 100.0
[10x0.157 ± 0.004 = 1.575 ± 0.008] [3.94]
1.75 ± 0.1
0.4 ± 0.05 [0.069 ± 0.004] 1.5 DIA. MAX. 4 ± 0.1 76.0
[0.016 ± 0.002] [0.059] [0.157 ± 0.004] [2.99] 25.0
[0.98]
7.5 ± 0.1
[0.295 ± 0.004] Direction of Feed
77.0 Max.
8.5 ± 0.1
[0.335 ± 0.004] [3.03] 16 +0.3 / -0.1 17.7
[0.630 +0.012 / -0.004] [0.697]
Direction of Feed
For 'C' Type Core Items: Packed in plastic bag (500 pcs)
Voltage
Pin Configuration
A = Axial Lead
C = Core
Remarks: Formed leads are available on request
Surge Capability
Voltage
Pin Configuration
A = Axial Lead
C = Core
SM = Surface Mount
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete
Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.
© 2017 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 12/12/17
Gas Discharge Tubes
SL1122A Series
Description
Agency Approvals
Features
Applications
a b
• MDF protection • Alarm panels
(centre electrode)
• ADSL equipment • General telecom
• XDSL equipment equipment
e
Additional Information
Electrical Characteristics
Notes:
1. Total current through centre electrode
2. Maximum Peak Break Over Voltage
Product Characteristics
Radial Lead Devices For Radial Lead Items: Packed in tray (100 pcs)
PROFILE VIEW Dimensions are in millimeters [and inches]
TOP VIEW
SL1122A XXX X
Voltage
1.5 Min
[0.059]
10.5 Max
[0.413] Pin Configuration
15.0 ± 1.0
[0.591 ± 0.039]
Temperature
- Time (Min to Max) (ts) 60 – 180 seconds
Ramp-down
Average Ramp-up Rate (Liquidus Temp
3°C/second max. Preheat
(TL) to peak) TS(min)
tS
TS(max) to TL - Ramp-up Rate 5°C/second max.
- Temperature (TL) (Liquidus) 217°C 25
Reflow
- Temperature (tL) 60 – 150 seconds time to peak temperature
(t 25ºC to peak) Time
Peak Temperature (TP) 260+0/-5 °C
Time within 5°C of Actual Peak * Devices that are soldered require inspection before use.
10 – 30 seconds
Temperature (tp)
Ramp-down Rate 6°C/second max.
Time 25°C to Peak Temperature (TP) 8 minutes max.
Do not exceed 260°C
120
Preheat Time: 60-180 seconds
100
Solder Pot Temperature: 280° C Maximum
80
20
0
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
10
20
30
40
50
60
70
80
90
0
Time (Seconds)
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete
Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.
© 2017 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 12/12/17
Gas Discharge Tubes
SL1021A/B Series
Description
Electrical Characteristics
SL1021A145
SL1021B145
116 145 174
500
SL1021A150 600
SL1021B150
120 150 180
SL1021B300
240 300 360 650 850
(at 100V) 5kA3
SL1021A350
SL1021B350
280 350 420 700 900
SL1021A400
SL1021B400
320 400 480
850 950
SL1021A420
SL1021B420
345 420 500
SL1021A450
SL1021B450
360 450 540 900 1000
SL1021A500
SL1021B500
400 500 600 950 1100
Additional Information
Voltage
13
12
(V)
11
10
9
8 Hold-over voltage
7
6
5
4
On-State voltage
3
2
1
0 200 400 600 800 1000 1200
0.5 1 2 5 10 15 30
Time (ns)
180
Temperature Minimum: 100° C
160 Temperature Maximum: 150° C
140
Preheat Time: 60-180 seconds
120
100
Solder Pot Temperature: 280° C Maximum
80
0
individually examined after soldering
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
10
20
30
40
50
60
70
80
90
0
Time (Seconds)
SL1021A/B Series
Minimum
Gap
9.9
9.9
[0.354]
[0.354]
15
[0.590]
NOTE: Failsafe option dimensions shown in green. 8.3 +0.3/-0.0 8.0 +0.3/-0.1
12.4 ± 1 [0.327 [0.315
[0.488 ± 0.039] Mounting Area +0.019/-0.00] +0.019/-0.004]
Shaped
Type 05Radial
/P Leaded Devices:
11.8 9.0 Core Devices:
[0.464] [0.354]
12.4
10.10 ±1 8.1. Mounting Area
[0.488 ±12.4
[0.398] 0.039]
±1 [0.319] Area PROFILE VIEW 11.8 SIDE VIEW TOP VIEW
Mounting Mounting
9.0 Area
[0.488 ± 0.039] [0.464]
11.8
Type 04 / R 11.8 Mounting
9.0 Area Type 01 / C [0.464]
[0.354]9.0
Type0.3mm
04 / R 12.4
[0.464]
[0.488
±1
11.8
± 0.039]
[0.464]
[0.354]9.0
[0.354]Area
Type 01 / C 10.10
11.8
2.2 ± 0.0 [0.354]Area
Mounting
8.1
Minimum 10.10 Mounting
8.1. [0.398]
10.10 [0.087 ± 0.000] 9.0
[0.464] [0.319]
8.1
Type 04 /R
Gap [0.398]11.8
10.10
[0.464]
[0.319]9.0
8.1.
[0.354]
Type 01 / C 1.2 ± 0.0
0.3mm [0.047 ± 0.000]
[0.398] 1.2 ± 0.0 [0.354]
[0.047 ± 0.000] [0.319]
[0.398] 9.9 [0.319] 10.10
[0.354] Minimum
0.3mm [0.398] 8.1
10.10 8.1. Gap
Minimum [0.319]
0.3mm [0.398] [0.319]
Minimum
0.3mm Gap
0.3mm
Gap
Minimum Minimum 9.9
15
Gap 9.9 Gap 6.0 ± 0.0 [0.354] 8.5 ± 0.0
0.3mm
[0.590] [0.236 ± 0.000] 9.9 [0.335 ± 0.000]
Minimum [0.354]
9.9 [0.354]
Gap [0.354] 9.9
16.8 9.9 1.0 DIA. [0.354]
[0.661] [0.354] [0.039]
4.4 15
[0.590] 15
[0.173]
[0.590] 10.75 ± 0.0 Overall Product Space
[0.423 ± 0.000] DO NOT ENCROACH
15
[0.590] 16.8 1.0 DIA.
[0.661] [0.039]
4.4 5.5± 0.3 5.5± 0.3 16.8 1.0 DIA. SOLDERING PAD LAYOUT
10.0 ± 0.3
[0.216± [0.661] [0.039]
[0.173] 4.40.12] [0.216± 0.12] [0.394 10.0
± 0.019]
± 0.3
[0.173] 16.8 1.0 DIA. Type 60 7.7 ± 0.3 [0.394 ± 0.019]
4.4
[0.661] [0.039]
Type 60 [0.303 ± 0.019]
7.7 ± 0.3 Ø7.0 ± 0.1
[0.27510.0
Ø7.0 ±±0.3
± 0.004]0.1
[0.173] [0.303 ± 0.019] [0.394
[0.275 ±± 0.019]
4.4± 0.3
[0.173± 0.12]
4.4± 0.3
4.4± 0.3
[0.173±
4.4±0.12]
0.3 Straight Radial Leaded Devices:
Type 60 7.7 ± 0.3
0.004]
Ø7.0 ± 0.1
[0.173± 0.12] [0.173± 0.12] [0.303 ± 0.019]
[0.275 ± 0.004]
4.4± 0.3 4.4± 0.3
[0.173± 0.12] [0.173± 0.12] 8.3 +0.3/-0.0 14.7 8.0 +0.3/-0.1
12.4 ± 1 [0.327
8.3 +0.3/-0.0 [0.579] [0.315
8.0 +0.3/-0.1
Type 14 / X
[0.488 ±12.4
0.039]
±1
[0.488 ± 0.039]
Mounting Area Type 06 / Y
+0.019/-0.00]
[0.327
+0.019/-0.00] 11.8
+0.019/-0.004]
Mounting Area [0.315
Type 05 / P 11.8
50 ± 3 [0.464]
Mounting
9.0 Area 8.3 +0.3/-0.0
[0.464] 9.0 +0.019/-0.004]
8.0 +0.3/-0.1
Type 05 / P 12.4
[1.968 ± 0.118[0.488
] [0.464]
±1
11.8
± 0.039]
[0.354]9.0 [0.327
+0.019/-0.00]
[0.354] [0.315
Mounting [0.354]Area
Mounting
Area 10.10 +0.019/-0.004]
10.10 8.1. 8.1 DIA. MAX.
Type 05 / P 11.8
[0.464]
[0.398]11.8
10.10 9.0
[0.319]9.0
8.1. PROFILE VIEW [0.398] SIDE VIEW TOP VIEW [0.319]
[0.464]
[0.398] [0.354] [0.354]
[0.319] PROFILE VIEW SIDE VIEW TOP VIEW
10.10 10.10 8.1.
0.3mm [0.398] 8.1 DIA. MAX. 0.3mm PROFILE VIEW
2.2 ± 0.0
[0.398] [0.319] SIDE VIEW
[0.087
2.2±±0.000]
0.0 TOP VIEW
Minimum
0.3mm [0.319] Minimum
Gap
Minimum Gap 1.2 ± 0.0 [0.087 ±1.20.000]
± 0.0
Gap 9.9 [0.047 ± 0.000]
1.2 ± 0.0 2.29.9 [0.047
± 0.0 1.2±±0.000]
0.0
0.3mm 0.3mm [0.047 ± 0.000]
Minimum Minimum [0.354]
9.9 [0.047 ± 0.000] [0.354]
[0.087 ± 0.000]
Gap Gap [0.354] 1.2 ± 0.0 1.2 ± 0.0
9.9 [0.047 ± 0.000] [0.047 ± 0.000]
15 [0.354] 15 6.0 ± 0.0 8.5 ± 0.0
[0.590] 15 [0.590]
[0.236 ± 0.000]
6.0 ± 0.0 [0.335
8.5±±0.000]
0.0
[0.590] [0.236 ± 0.000] [0.335 ± 0.000]
15 6.0 ± 0.0 8.51.0 DIA.
± 0.0
[0.590] 16.8 23.8 1.0 DIA. [0.236 ± 0.000]
16.8
[0.039]
[0.335 ± 0.000]
[0.937]
[0.661] [0.661]
16.8 [0.039]
1.0 DIA.
22 4.4 [0.661] [0.039]
[0.173] 4.4
[0.866] 10.75 ± 0.0
[0.173] 16.8 1.0 DIA..1.0 DIA. Overall Product Space
[0.42310.75
± 0.000]
± 0.0 DO NOT ENCROACH
[0.661] [0.039] [0.039] Overall Product Space
4.4 [0.423 ± 0.000] DO NOT ENCROACH
[0.173] SOLDERING 10.75
PAD±LAYOUT
0.0
5.5± 0.3 5.5± 0.3 6.35 ± 0.5 6.35 ± 0.5 Overall Product Space
[0.423 ±PAD
SOLDERING 0.000]
LAYOUT DO NOT ENCROACH
[0.216± 0.12]
5.5± 0.3 [0.216±
5.5±0.12]
0.3 [0.25 ± 0.25] [0.25 ± 0.25]
[0.216± 0.12] [0.216± 0.12]
5.5± 0.3 5.5± 0.3 SOLDERING PAD LAYOUT
[0.216± 0.12] [0.216± 0.12]
14.7
[0.579]
14.7
Straight
Type 14"T"
/ XLeaded Devices: Type 06 / Y [0.579] Mounting Area
Type 14 / X 50 ± 3
Type 06 / Y 11.814.7
[0.464]
11.8
Mounting
9.0 Area
[0.579] [0.354]9.0
[1.968 ± 50
0.118
± 3] [0.464]
Type 14 / X [1.968 ± 0.118 ] Mounting Area Type 06 / Y 10.10
11.8 8.1 DIA.
[0.354]Area
Mounting
MAX.
11.8 Mounting
9.0 Area [0.398]
10.10 9.0 MAX.
50
[0.464] ±3
11.8 [0.464] [0.319]
8.1 DIA.
[0.354]9.0 [0.398] [0.354]
[0.319]
[1.968 ± 0.118 ]
[0.464]
10.10 [0.354]Area
Mounting 10.10
11.8 0.3mm 8.1 DIA. MAX.
[0.398]
10.10 8.1 DIA. MAX.
9.0 [0.398] [0.319]
[0.464]
[0.398] [0.319]
8.1 [0.354]
DIA. MAX. Minimum
0.3mm
[0.319] Gap
Minimum
10.10 Gap 9.9
0.3mm [0.398] 8.1 DIA. MAX. 0.3mm
Minimum
0.3mm Minimum [0.354]
9.9
[0.319] [0.354]
Gap
Minimum Gap
Gap
0.3mm 9.9
Minimum 15 [0.354]
Gap [0.590] 15
[0.590]
23.8 15 1.0 DIA.
[0.590] 16.8
[0.937]
23.8 [0.661] [0.039]
1.0 DIA.
16.8
[0.937] [0.661] [0.039]
22
[0.866] 22 23.8 16.8 1.0 DIA.
[0.866] [0.937] 1.0 DIA.. [0.661] [0.039]
[0.039]
1.0 DIA..
22 [0.039]
[0.866] 6.35 ± 0.5
1.0 DIA.. 6.35 ± 0.5
[0.039] [0.25 ±6.35
0.25]
± 0.5 [0.256.35
± 0.25]
± 0.5
[0.25 ± 0.25] [0.25 ± 0.25]
6.35 ± 0.5 6.35 ± 0.5
[0.25 ± 0.25] [0.25 ± 0.25]
SL1021A/B Series
Box (Cardboard)
~58
Tray (PET)
for 50 Pcs.
~135
Part Numbering System and Ordering Information Packaging
SL102x x xxx x x PMT8 xxx x x For 'SL1021A/B' device type C, R, P, Y packing
Series Series
SL1021 PMT8
SL1024
Surge Capability
A = 10kA 35
B = 20kA ~2
Breakdown Voltage Breakdown Voltage
090 = 90V 300 = 300V 090 = 90V
145 = 145V 350 = 350V 230 = 230V
150 = 150V 400 = 400V 250 = 250V Box (Cardboard)
200 = 200V 420 = 420V 350 = 350V
230 = 230V 450 = 450V 400 = 400V
250 = 250V 500 = 500V
260 = 260V 600 = 600V Tray, Cover (PET)
~55
Configuration Code Configuration Code
(See Device Dimensions section) (See Device Dimensions section)
Tray, Bottom (PET)
C Y 01 10
R X
for 100 Pcs.
04 14
P 05 60
06 PE Form
Option Code Option Code
Blank = No failsafe Blank = No Failsafe
F or G = With Failsafe F = With Failsafe
58
~2
Box (Cardboard)
~58
Tray (PET)
for 50 Pcs.
~135
Device~2Type
35 Description Quantity
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete
Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.
© 2017 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 12/12/17
Gas Discharge Tubes
CG/CG2 Series
Description
AGENCY AGENCY FILE NUMBER The CG Series (75V-110V) is ideal for protection
of test and communication equipment and other
E1286621 devices in which low voltage limits and extremely
low arc voltages are required.
E3201162
NOTES: The CG2 Series (145V-1000V) is ideal for protecting
1. Certified to UL 497B.
2. Only CG2300, CG2470, CG2600, CG2800 and CG221000. Certified to UL 1449.
equipment where higher voltage limits and holdover
voltages are necessary.
2 Electrode GDT Graphical Symbol
Features
Applications
Datasheet Resources Samples
CG/CG2 • Communication lines • Instrumentation circuits
and equipment • Medical electronics
• CATV equipment • ADSL equipment
• Test equipment • Telecom SLIC
• Data lines protection
• Power supplies
Electrical Characteristics
Product Characteristics
8.71 [0.343]
Device Dimensions
5.89 [0.232]
Ø6.81 [0.268]
0.47 ± 0.1
Leaded 'L' Type Straight Axial Devices Leaded 'LS' Type Shaped Lead Devices
8.10DIA. MAX.
[0.319]
8.40 ± 0.3
[0.331 ± 0.012]
6.07 ± 0.15
[0.239 ± 0.006]
0.80
0.004 8.4 ± 0.3 [0.032]
62 ± 2 [0.331 ± 0.012]
2 Surfaces 0.40 ± 0.03
[0.0157 ± 0.0012]
9.85 ± 0.30
[0.388 ± 0.012]
PROFILE VIEW TOP VIEW SOLDER PAD LAYOUT
11.15 ± 0.30
6.07± 0.30 8.10 Max. [0.439 ± 0.012]
[0.239 ± 0.012] [0.319 DIA Max.]
SOLDER PAD LAYOUT
Core Devices 9.85 [0.388]
9.85
[0.388]
8.40 ± 0.3 8.66 [0.341]
[0.331 ± 0.012]
TOP VIEW PROFILE VIEW SEMI–PROFILE VIEW 8.60
[0.339]
8.10 Max.
[0.032 Max.]
6.07 ± 0.15 1.77 [0.070]
[0.239 0.81
± 0.0059]
0.004 8.4 ± 0.3 [0.032]
5.89 [0.232] 1.80
2 Surfaces 0.40 ± 0.03 [0.331 ± 0.012] 11.68 [0.460] [0.071]
[0.0157 ± 0.0012]
11.65
9.85 ± 0.30 [0.459]
8.10 Max.
[0.388 ± 0.012]
11.15 ± 0.30
[0.439 ± 0.012]
11.50
.3
30 0
6
± .00
0. 7
2 9]
16 16 16 16 16 0.47 ± 0.1
250G 250G 250G 250G 250G
XXXX XXXX XXXX XXXX XXXX [0.019 ± 0.0039]
24.00
SOLDER PAD LAYOUT
2.29 [0.090]
16.00
5.89 [0.232]
1.01
(25.7)
Direction of Feed
Temperature
- Time (Min to Max) (ts) 60 – 180 secs
Ramp-down
Average ramp up rate (Liquidus Temp
3°C/second max Preheat
(TL) to peak TS(min)
tS
TS(max) to TL - Ramp-up Rate 5°C/second max
- Temperature (TL) (Liquidus) 217°C 25
Reflow
- Temperature (tL) 60 – 150 seconds time to peak temperature
(t 25ºC to peak) Time
Peak Temperature (TP) 260 +0/-5
°C
Time within 5°C of actual peak
10 – 30 seconds
Temperature (tp)
Ramp-down Rate 6°C/second max
Time 25°C to peak Temperature (TP) 8 minutes Max.
Do not exceed 260°C
180
Temperature Minimum: 100° C
160 Temperature Maximum: 150° C
140
Preheat Time: 60-180 seconds
120
100
Solder Pot Temperature: 280° C Maximum
80
20
0
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
10
20
30
40
50
60
70
80
90
0
Time (Seconds)
6.4
[0.252]
5.0 Pitch
[0.197]
Packaging Dimensions
254.0 - 356.0
[10.0 - 14.0]
<0.8 Max
Direction of Feed
80.0
52.4 [3.15]
[2.063]
22.8
[0.898]
6.4
[0.252]
5.0 Pitch
[0.197]
275.0
[10.83]
10x4 ± 0.1 = 40 ± 0.2 100.0
254.0 - 356.0 [10 x 0.157 ± 0.004 = 1.575 ± 0.008] [3.94]
[10.01.75 ± 0.1
- 14.0]
0.4 ± 0.05 [0.069 ± 0.004] 1.5 DIA. MAX. 4 ± 0.1 76.0
[0.016 ± 0.002] [0.059] [0.157 ± 0.004] [2.99] 25.0
[0.98]
7.5 ± 0.1
[0.295 ± 0.004]
8.5 ± 0.1
[0.335 ± 0.004] 16 +0.3 / -0.1 17.7
[0.630 +0.012 / -0.004] Direction of Feed [0.697]
80.0
[3.15] Direction of Feed
1.9
[0.075] 25.7
[1.01]
11.5 ± 0.1 Direction of Feed
[0.453 ± 0.004]
0.5 ± 0.01
[0.020 ± 0.004]
1.5 DIA. MAX.
9 ± 0.1 [0.059] 16 ± 0.1
[0.354 ± 0.004] [0.630 ± 0.004]
CG2 XXX XX * XX
Series Examples:
CG -- for 75, 90, or 110V
CG2 -- for 145V to 1000V CG75 -- A non-leaded 75V device
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete
Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.
© 2017 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 12/12/17
Gas Discharge Tubes
SL1026 Series
Description
The SL1026 Series is a heavy-duty transient
suppresser using Gas Plasma technology. In
response to transients that exceed the device's
breakover voltage, the device changes from a very
high impedance state to a low impedance state to
conduct harmful current away from the protected
system. The SL1026 is designed to protect electrical
and electronic equipment such as communications,
control and railway systems. Carefully designed
geometry ensures against short circuiting if a failure
occurs due to conditions and events beyond the
design criteria. Optional electrical mounting clip (part
3 Electrode GDT Graphical Symbol SL1053 ) is available to aid mounting and connection.
a = TIP Features
a b b = RING • RoHS compliant • Will protect against
e = GROUND capacitor discharge
(centre electrode) • 55 kA surge capability
(single shot) tested with voltage transient
8/20μS pulse as defined waveforms as specified
e in RIA 12.
by IEC 61000-4-5
• 40 kA surge capability • Will protect against
Additional Information double exponential
(repetitive)
voltage transient
• Will protect against
waveforms as specified
Trapezoidal waveforms
in IEC 571.
as specified in RIA 12.
Datasheet Resources Samples
Applications
Electrical Characteristics
DC Voltage 1
AC 1
AC 1
Surge Max
1,2
Ø8.7 Ø9.1
Max Max
Voltage
(V)
On-State voltage
Electrical Specifications
Insulation
> 10GΩ at 100 Volts
Resistance
Physical Specifications GDT devices are provided as bulk pack in poly bag --
20 pieces per bag and 5 bags per carton.
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete
Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.
© 2017 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 12/12/17
Gas Discharge Tubes
SE Series
SE Series RoHS
Description
Electrical Characteristics
Product Characteristics Tape and Reel Dimensions (IEC 60286-3, dimension in mm)
2.1 ±0.1 5°
Device Tin Plated 17.5±12.5 Microns Tape Specifications
Materials Tape Specifications
IEC 60286-3 section
Construction Ceramic Insulator. IEC 60286-3 in mm
Dimensions section
B-B
5°
Dimensions in mm B-B
Storage and
Operational -40 to +90 °C
1.75 ±0.1
section
section 2 ±0.1 4 ±0.1
1.75 ±0.1
A-A
A-A
Temperature 0.4 ±0.05
0.4 ±0.05 2 ±0.1 A4 ±0.10 Ø 1.55 1.5 Ø 1.6 ±0.1
±0.05
±0.05
A
12 - 0.15.5 ±0.1
5°
4.9 ±0.1 5°
+0.3
5.5 ±0.1
0
B B
3 ±0.1
A 3.65 ±0.1 8 ±0.1
3.7 ±0.1
R0.5 typical
B B
Max dynamic breakover SMD-Tape has to withstand
Hold-over voltage
Reel Specifications
On-State voltage
Reel
IEC Specifications
60286-3
Dimensions
IEC 60286-3in mm
Dimensions in mm
1.5 min.
1.5 min.
min. max.
20.2 min.
Ø100 min.
12.8 min.
Ø330 max.
20.2 min.
Ø100Ø330
R0.75
12.8 min.
18.4 max.
R0.75
18.4 max.
12.4 +2/-0
12.4 +2/-0
11.9 min.
11.9 min.
© 2017 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 12/12/17
Gas Discharge Tubes
SE Series
Temperature
- Time (Min to Max) (ts) 60 – 180 secs
Ramp-down
Average ramp up rate (Liquidus Temp
3°C/second max Preheat
(TL) to peak TS(min)
tS
TS(max) to TL - Ramp-up Rate 5°C/second max
- Temperature (TL) (Liquidus) 217°C 25
Reflow
- Temperature (tL) 60 – 150 seconds time to peak temperature
(t 25ºC to peak) Time
Peak Temperature (TP) 260 +0/-5
°C
Time within 5°C of actual peak
10 – 30 seconds
Temperature (tp)
Ramp-down Rate 6°C/second max
Time 25°C to peak Temperature (TP) 8 minutes Max.
Do not exceed 260°C
SE xxx
Dimensions in mm and inch [...] Series
[0.126 +/- 0.012] [0.063+/- 0.008] 1206 Square GDT
3.2+/-0.3 1.6+/- 0.2
Breakdown Voltage
[0.063+/- 0.008]
140 = 140V
1.6+/- 0.2
200 = 200V
230 = 230V
350 = 350V
470 = 470V
[0.157] 500 = 500V
4 Packaging
1.2 1.6
2.4
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete
Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.
© 2017 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 12/12/17
Gas Discharge Tubes
SG Series
SG Series RoHS
Description
Features
Electrical Characteristics
Storage and
Operational -40 to +90 °C
Temperature
Voltage
(V)
Temperature
- Time (Min to Max) (ts) 60 – 180 secs
Ramp-down
Average ramp up rate (Liquidus Temp
3°C/second max Preheat
(TL) to peak TS(min)
tS
TS(max) to TL - Ramp-up Rate 5°C/second max
- Temperature (TL) (Liquidus) 217°C 25
Reflow
- Temperature (tL) 60 – 150 seconds time to peak temperature
(t 25ºC to peak) Time
Peak Temperature (TP) 260+0/-5 °C
Time within 5°C of actual peak
10 – 30 seconds
Temperature (tp)
Ramp-down Rate 6°C/second max
Time 25°C to peak Temperature (TP) 8 minutes Max.
Do not exceed 260°C
Type Production
Dimensions in Millimeters.
Code Year Code
(last digit)
Tape and Reel Dimensions (IEC 60286-3, dimension in mm) Part Numbering System and Ordering Information
Tape Specifications
IEC 60286-3
section 5° SG xxx Q
Dimensions in mm B-B
Series
section Square GDT
1.75 ±0.1
A-A
0.4 ±0.05 2 ±0.1 4 ±0.10 Ø 1.55 ±0.05 Ø 1.6 ±0.1 Breakdown Voltage
A 75 = 75V
90 = 90V
150 = 150V
5.5 ±0.1
4.9 ±0.1 5°
+0.3
200 = 200V
12 0
230 = 230V
300 = 300V
B B 350 = 350V
3 ±0.1 400 = 400V
R0.5 typical A 3.65 ±0.1 8 ±0.1
420 = 420V
SMD-Tape has to withstand
450 = 450V (Not available without “Q” suffix)
a minimum Force of 500 = 500V (Not available without “Q” suffix)
F > 20 N / pocket 600 = 600V (Not available without “Q” suffix)
2 Kg / pocket
minimum vertical load Device Option Code
(minimum checking
quantity:10 pockets) (Blank) = Standard device
Q = Quick Response Version
(300V, 350V, 420V, 450V,
500V, 600V only)
Packaging
Reel Specifications
IEC 60286-3 Quantity and Packaging
Part Number and Device Type
Dimensions in mm Description
1.5 min.
Ø330 max.
20.2 min.
Ø100 min.
12.8 min.
R0.75
18.4 max.
12.4 +2/-0
11.9 min.
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete
Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.
© 2017 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 12/12/17
Gas Discharge Tubes
SH Series
SH Series RoHS
Description
Features
Two Electrode GDT Graphical Symbol
• Excellent response to • Offered with squared
fast rising transients body package
• GHz working frequency • Non-Radioactive
• 5kA, 8/20μs surge • Ultra Low capacitance
capability as defined (<0.7pF)
by IEC 61000-4-5 2nd • Lead-free and RoHS
Additional Information Edition compliant
• UL recognized
Applications
Datasheet Resources Samples
• CATV equipment • IEEE 802.3 compliant
• Antennas Ethernet interfaces
• RS 485 • Broad Band equipment
• Telecom Base Station • xDSL, ADSL, ADSL2,
VDSL, and VDSL2
• Power Supply AC Main
• Medical Electronics
• G.fast
• Test Equipment
• EV power Charging
• General Telecom
• Inverter/Variable
Equipment
Frequency Drivers
(VFDs) • Renewable Energy
Electrical Characteristics
Note:
* Reference REA PE-80, 0.2A, tested to ITU-T Rec K.12 and REA PE 80 <150 ms.
** DC spark-over may exceed ± 25% after discharge, but will continue to protect without venting
@1.0GHz = 0.08dB
Device Tin Plated 17.5 ± 12.5
Materials Microns @1.4GHz = 0.16dB
Construction: Ceramic Insulator
@1.8GHz = 0.26dB
Storage and Operational
-40 to +90°C @2.0GHz = 0.33dB
Temperature
@2.4GHz = 0.47dB
@2.8GHz = 0.59dB
Voltage Vs. Time Characteristic
@3.1GHz = 0.70dB
@3.5GHz = 0.89dB
Max dynamic
800 breakover voltage @4.0GHz = 1.24dB
Note: Insertion data for customer reference only, application testing needed for verification.
600
Voltage (V)
400
200
On-state voltage
0
0 200 400 600 800 1000 1200
Time (ns)
Temperature
- Time (Min to Max) (ts) 60 – 180 secs
Ramp-down
Average ramp up rate (Liquidus Temp
3°C/second max Preheat
(TL) to peak TS(min)
tS
TS(max) to TL - Ramp-up Rate 5°C/second max
- Temperature (TL) (Liquidus) 217°C 25
Reflow
- Temperature (tL) 60 – 150 seconds time to peak temperature
(t 25ºC to peak) Time
Peak Temperature (TP) 260 +0/-5
°C
Time within 5°C of actual peak
10 – 30 seconds
Temperature (tp)
Ramp-down Rate 6°C/second max
Time 25°C to peak Temperature (TP) 8 minutes Max.
Do not exceed 260°C
Dimensions in millimeters
A 3A
TOP VIEW PROFILE VIEW
0.5 ± 0.2
5.0 ± 0.2
4.8 ± 0.2
4.2 ± 0.3
Type Code Month Code
A SH75 A January
TOP VIEW
B SH90 B February
0.8 S SH145 C March
D SH230 D April
6.0 R SH250 E May
E SH300 F June
G SH350 G July
3.7
I SH400 H August
Recommended Soldering Pad Layout
P SH470 I September
V SH600 J October
K November
L December
SH X.X
Series
Square GDT
Breakdown Voltage
75 = 75V
90 = 90V
145 = 145V
230 = 230V
250 = 250V
300 = 300V
350 = 350V
400 = 400V
470 = 470V
600 = 600V
Taping
Unit = mm D P0
>1.5
Packaging Quantity:
900 pcs per reel (13”)
100 Typ.
1 reel per inner box
10 inner boxes per carton
9,000 pcs per full carton
18 Typ.
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete
Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.
© 2017 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 12/12/17
littelfuse.com
circuitprotection@littelfuse.com
EC141Nv1217