Professional Documents
Culture Documents
3-2. DTH Button Bits en
3-2. DTH Button Bits en
m
co
in drilling applications, and is suitable for hard to very hard and abrasive rock formations
in applications with high air pressures. It maintains average hole straightness but have an
s.
excellent penetration rate. This kind of bits is used primarily in blast-hole work. So typically flat face with
ll
hemi-spherical buttons design are the most popular choice.
ri
Convex Face
ed
A classic design for soft to medium hard rock formation, but not so abrasive with low to
medium air pressures. This face has been utilized in very hard drilling formations where
ac
the face of the bit tends to be prematurely worn away. The convex style tends to keep the
w.
drilling face intact longer by drilling with the two rows of buttons on the convex face. This bit keeps average hole
ww
straightness but drills at excellent speed. It is the most resistance to steel wash, and may reduce the load and wear
on the Gauge Buttons, gives excellent penetration rate but poor hole deviation control.
Concave Face
This bit is ideal for drilling through medium to hard formations, but less abrasive and
fractured. Good hole deviation control with an average rate of penetration and good
flushing capacity, especially for deep hole drilling.
Very hard
Flat face High Fair Good
and abrasive
Convex Low to Medium to
Average Excellent
face medium hard
formation, best rate, but best suited to ground, as well as loose rock
ri
suited to hard ground and very medium hard ground and mildly formation, but best suited to soft ground.
ed
to 45,000 PSI (170 to 300 MPa). 25,000 PSI (100 to 170 MPa). PSI (70 to 140 MPa)
w.
ww
m
co
Bits Shank Illustration Shank Style Identification
s.
Bulroc BR3, Boart BH75, Minroc 3, Klemm KR-3,
Bulroc BR2, Minroc 2
ll
Bohler LH-78ZD
ri
ed
Φ = 6 Spline, L = 165mm/ 6.5in ac Φ = 6 Spline, L = 164mm/ 6.46in
w.
Ingersoll Rand DHD3.5, Atlas Copco TD35,
ww
Halco Mach33/303
Sandvik XL3
Φ = 8 Spline, L = 215.2mm/8.47in
Φ = 8 Spline, L = 224 mm/ 8.82in
Ingersoll Rand DHD340A/DHD4, Atlas Copco COP44,
Atlas Copco COP34
Atlas Copco Secoroc4/44, Numa4, Mincon 4HR
m
co
s.
ll
Φ = 12 Spline, L = 228mm/ 8.98in Φ = 7 Spline, L = 190mm/ 7.48in
Sandvik XL4
ri
Halco Mach 40/44, Halco Dominator 400
ed
ac
w.
ww
Φ = 8 Spline, L = 260mm/ 10.24in, L’= 55mm/ 2.17in Φ = 8 Spline, L = 260mm/ 10.24in, L’= 54.5mm/ 2.15in
Ingersoll Rand QL50, Atlas Copco COP54 gold, Sandvik Mission 50/55
Atlas Copco TD50/TD55/HP50/ HP55, Numa Patriot 50
m
Numa Challenger6/Patriot 6, Mincon 6BH360,
co
Stenvick ADEC-6M, Halco Mach 60M
Sandvik Mission XL61/PD61, Halco Mach 60IR
s.
ll
ri
ed
Φ = 8 Spline, L = 324mm/ 12.76in, L’= 54mm/ 2.13in
ac
Φ = 8 Spline, L = 309mm/ 12.17in, L’= 57mm/ 2.24in
Ingersoll Rand QL60, Atlas Copco COP64 Gold,
w.
Atlas Copco TD60/ TD65/ TD70/HP60/HP65, Sandvik Mission 60/60W/65
ww
Mincon 6DH
m
co
s.
ll
ri
Φ = 12 Spline, L = 332mm/ 13.07in, L’= 52.3mm/ 2.05in Φ = 12 Spline, L = 329mm/ 12.95in
ed
Sandvik SD10 Numa100
ac
w.
ww
Φ = 8 Spline, L = 356mm/ 14.02in, L’= 60.3mm/ 2.37in Φ = 10 Spline, L = 375mm/ 14.76in, L’= 55mm/ 2.17in
Ingersoll Rand DHD112, Sandvik XL12, Sandvik SD12(A100-15), Drillquip T1120A,
Halco Mach132, Drillquip T1120-112, Epley 1200 Halco Mach120
Φ = 8 Spline, L = 491mm/ 19.33in, L’= 52.3mm/ 2.06in Φ = 8 Spline, L = 468mm/ 18.43in, L’= 48mm/ 1.89in
Numa 120
Numa 125
m
co
s.
ll
ri
m
76 3 2 6×13 3×13
co
80 3 3/16 2 6×14 3×13
s.
90 3 1/2 2 6×14 5×12
ll
Shank Style Diameter Weight Part Number
Identification mm in kg lb Flat Face Convex Face
ri
76 3 3.6 7.9 32-0221-076 32-0222-076
ed
Bulroc BR2 80 3 3/16 4 8.8 32-0221-080 32-0222-080
90 3 1/2 4.2 ac 9.3 32-0221-090 32-0222-090
w.
ww
Ingersoll Rand
95 3 3/4 4.8 11 32-0331-095 32-0332-095
DHD3.5
ri
m
co
105 4 1/8 5.8 13 32-0341-105 32-0342-105
s.
85 3 3/8 4.2 9.3 32-0351-085 32-0352-085
90 3 1/2 4.5 9.9 32-0351-090 32-0352-090
ll
Atlas Copco
95 3 3/4 4.7 10 32-0351-095 32-0352-095
ri
COP32
100 3 7/8 5 11 32-0351-100 32-0352-100
ed
105 4 1/8 5.2 11 32-0351-105 32-0352-105
85
90
3 3/8
3 1/2
4.2
4.5
ac 9.3
9.9
32-0361-085
32-0361-090
32-0362-085
32-0362-090
w.
Atlas Copco
95 3 3/4 4.8 11 32-0361-095 32-0362-095
ww
COP34
100 3 7/8 5 11 32-0361-100 32-0362-100
105 4 1/8 5.5 12 32-0361-105 32-0362-105
m
co
127 5 11.5 25 32-0441-127 32-0442-127 32-0443-127
s.
105 4 1/8 9.3 21 32-0421-105 32-0422-105 32-0423-105
110 4 1/4 10 22 32-0421-110 32-0422-110 32-0423-110
ll
Sandvik
115 4 1/2 10.5 23 32-0421-115 32-0422-115 32-0423-115
ri
Mission 40
121 4 3/4 12 26 32-0421-121 32-0422-121 32-0423-121
ed
127 5 13 29 32-0421-127 32-0422-127 32-0423-127
105
110
4 1/8
4 1/4
8.2
8.5
ac 18
19
32-0451-105
32-0451-110
32-0452-105
32-0452-110
32-0453-105
32-0453-110
w.
Atlas Copco
115 4 1/2 8.9 20 32-0451-115 32-0452-115 32-0453-115
ww
COP 42
121 4 3/4 9.5 21 32-0451-121 32-0452-121 32-0453-121
127 5 10.8 24 32-0451-127 32-0452-127 32-0453-127
105 4 1/8 8 18 32-0461-105 32-0462-105 32-0463-105
110 4 1/4 8.5 19 32-0461-110 32-0462-110 32-0463-110
Halco Mach
115 4 1/2 8.8 19 32-0461-115 32-0462-115 32-0463-115
40/44
121 4 3/4 9.4 21 32-0461-121 32-0462-121 32-0463-121
127 5 10.5 23 32-0461-127 32-0462-127 32-0463-127
105 4 1/8 9 20 32-0471-105 32-0472-105 32-0473-105
110 4 1/4 9.5 21 32-0471-110 32-0472-110 32-0473-110
Sandvik XL4 115 4 1/2 10 22 32-0471-115 32-0472-115 32-0473-115
121 4 3/4 11.5 25 32-0471-121 32-0472-121 32-0473-121
127 5 12.5 28 32-0471-127 32-0472-127 32-0473-127
m
Ingersoll Rand
co
146 5 3/4 17 37 32-0511-146 32-0512-146 32-0513-146
DHD350R
s.
152 6 17.5 39 32-0511-152 32-0512-152 32-0513-152
165 6 1/2 18.5 41 32-0511-165 32-0512-165 32-0513-165
ll
137 5 3/8 15.5 34 32-0531-137 32-0532-137 32-0533-137
ri
140 5 1/2 16 35 32-0531-140 32-0532-140 32-0533-140
ed
Sandvik SD5 146 5 3/4 16.5 36 32-0531-146 32-0532-146 32-0533-146
152
165 6 1/2
6 17
18
ac 37
40
32-0531-152
32-0531-165
32-0532-152
32-0532-165
32-0533-152
32-0533-165
w.
137 5 3/8 15.5 34 32-0541-137 32-0542-137 32-0543-137
ww
m
mm in [No.]×[mm] [No.]×[mm]
co
152 6 2 8×17 8×14
s.
165 6 1/2 2 8×18 9×16
ll
172 6 3/4 2 8×18 10×16
178 7 2 8×18 10×16
ri
190 7 1/2 3 9×18 11×16
ed
203 8 3 9×18 12×16
Shank Style Diameter ac
Weight Part Number
w.
Identification mm in kg lb Flat Face Convex Face Concave Face
ww
10
m
co
190 7 1/2 28.5 63 32-0651-190 32-0652-190 32-0653-190
s.
203 8 32 71 32-0651-203 32-0652-203 32-0653-203
152 6 25.5 56 32-0661-152 32-0662-152 32-0663-152
ll
165 6 1/2 26.8 59 32-0661-165 32-0662-165 32-0663-165
ri
172 6 3/4 28.5 63 32-0661-172 32-0662-172 32-0663-172
Sandvik XL6
ed
178 7 29.5 65 32-0661-178 32-0662-178 32-0663-178
190
203
7 1/2
8
31.5
33
ac 69
73
32-0661-190
32-0661-203
32-0662-190
32-0662-203
32-0663-190
32-0663-203
w.
ww
11
m
co
292 11 1/2 85 187 32-0841-292 32-0842-292 32-0843-292
s.
305 12 95 209 32-0841-305 32-0842-305 32-0843-305
203 8 37 82 32-0821-203 32-0822-203 32-0823-203
ll
216 8 1/2 48 106 32-0821-216 32-0822-216 32-0823-216
ri
Sandvik 241 9 1/2 63 139 32-0821-241 32-0822-241 32-0823-241
ed
Mission 80/85 254 10 70 154 32-0821-254 32-0822-254 32-0823-254
292
305
11 1/2
12
85.5
98
ac188
216
32-0821-292
32-0821-305
32-0822-292
32-0822-305
32-0823-292
32-0823-305
w.
ww
SD10 314 12 3/8 128 282 32-1013-314 314 12 3/8 112 247 32-1023-314
s.
320 12 5/8 132 291 32-1013-320 320 12 5/8 115 254 32-1023-320
ll
12
m
mm in [No.]×[mm][No.]×[mm][No.]×[mm]
co
311 12 1/4 3 15×19 19×19 9×16
s.
314 12 3/8 3 18×18 23×18 9×16
ll
320 12 5/8 3 18×18 24×18 9×16
333 13 3 18×19 24×18 14×16
ri
349 13 3/4 3 15×19 24×19 15×16
ed
381 15 3 18×18 30×18 21×16
400 15 3/4 3 18×19 30×19 ac 29×16
w.
419 16 1/2 3 18×19 30×19 30×16
ww
Shank Style Diameter Weight Part Number Shank Style Diameter Weight Part Number
Identification mm in kg lb Concave Face Identification mm in kg lb Concave Face
311 12 1/4 140 309 32-1213-311 311 12 1/4 172 379 32-1223-311
314 12 3/8 145 320 32-1213-314 314 12 3/8 173 381 32-1223-314
320 12 5/8 150 331 32-1213-320 320 12 5/8 176 388 32-1223-320
Ingersoll Rand 333 13 155 342 32-1213-333 Sandvik 333 13 181 399 32-1223-333
DHD112 349 13 3/4 170 375 32-1213-349 SD12 349 13 3/4 195 430 32-1223-349
381 15 190 419 32-1213-381 381 15 200 441 32-1223-381
400 15 3/4 230 507 32-1213-400 400 15 3/4 239 527 32-1223-400
419 16 1/2 235 518 32-1213-419 419 16 1/2 245 540 32-1223-419
311 12 1/4 162 162 32-1243-311 311 12 1/4 162 162 32-1253-311
314 12 3/8 168 168 32-1243-314 314 12 3/8 168 168 32-1253-314
320 12 5/8 172 172 32-1243-320 320 12 5/8 172 172 32-1253-320
333 13 180 180 32-1243-333 333 13 180 180 32-1253-333
Numa 120 Numa 125
349 13 3/4 205 205 32-1243-349 349 13 3/4 205 205 32-1253-349
381 15 228 228 32-1243-381 381 15 228 228 32-1253-381
400 15 3/4 270 270 32-1243-400 400 15 3/4 270 270 32-1253-400
419 16 1/2 277 277 32-1243-419 419 16 1/2 277 277 32-1253-419
Note: 1. All diameters showed as above are only our usual diameters, other diameters are also available upon
m
customized request;
co
3. Face design, T.C shape, buttons configuration and Flushing Holes number must be confirmed when place
order our DTH button bits.
ll
ri
ed
ac
w.
ww
13