Professional Documents
Culture Documents
Aisi 340 Info PDF
Aisi 340 Info PDF
Aisi 340 Info PDF
Chemical Formula
Fe, <0.08% C, 17.5-20% Cr, 8-11% Ni, <2% Mn, <1% Si, <0.045% P, <0.03% S
Topics Covered
Background
Key Properties
Composition
Mechanical Properties
Physical Properties
Grade Specification Comparison
Possible Alternative Grades
Corrosion Resistance
Heat Resistance
Heat Treatment
Welding
Machining
Dual Certification
Applications
Background
Grade 304 is the standard "18/8" stainless; it is the most versatile and most widely used stainless steel, available in a wider range of
products, forms and finishes than any other. It has excellent forming and welding characteristics. The balanced austenitic structure of
Grade 304 enables it to be severely deep drawn without intermediate annealing, which has made this grade dominant in the
manufacture of drawn stainless parts such as sinks, hollow-ware and saucepans. For these applications it is common to use special
"304DDQ" (Deep Drawing Quality) variants. Grade 304 is readily brake or roll formed into a variety of components for applications
in the industrial, architectural, and transportation fields. Grade 304 also has outstanding welding characteristics. Post-weld annealing
is not required when welding thin sections.
Grade 304L, the low carbon version of 304, does not require post-weld annealing and so is extensively used in heavy gauge
components (over about 6mm). Grade 304H with its higher carbon content finds application at elevated temperatures. The austenitic
structure also gives these grades excellent toughness, even down to cryogenic temperatures.
Key Properties
These properties are specified for flat rolled product (plate, sheet and coil) in ASTM A240/A240M. Similar but not necessarily
identical properties are specified for other products such as pipe and bar in their respective specifications.
Composition
Typical compositional ranges for grade 304 stainless steels are given in table 1.
Grade C Mn Si P S Cr Mo Ni N
min. - - - - - 18.0 8.0 -
304 -
max. 0.08 2.0 0.75 0.045 0.030 20.0 10.5 0.10
min. - - - - - 18.0 8.0 -
304L -
max. 0.030 2.0 0.75 0.045 0.030 20.0 12.0 0.10
min. 0.04 - - - 18.0 8.0
304H -0.045 - -
max. 0.10 2.0 0.75 0.030 20.0 10.5
Mechanical Properties
Typical mechanical properties for grade 304 stainless steels are given in table 2.
Table 2. Mechanical properties of 304 grade stainless steel
Physical Properties
Typical physical properties for annealed grade 304 stainless steels are given in table 3.
Table 3. Physical properties of 304 grade stainless steel in the annealed condition
Approximate grade comparisons for 304 stainless steels are given in table 4.
Possible alternative grades to grade 304 stainless steels are given in table 5.
Corrosion Resistance
Excellent in a wide range of atmospheric environments and many corrosive media. Subject to pitting and crevice corrosion in warm
chloride environments, and to stress corrosion cracking above about 60°C. Considered resistant to potable water with up to about
200mg/L chlorides at ambient temperatures, reducing to about 150mg/L at 60°C.
Heat Resistance
Good oxidation resistance in intermittent service to 870°C and in continuous service to 925°C. Continuous use of 304 in the 425-
860°C range is not recommended if subsequent aqueous corrosion resistance is important. Grade 304L is more resistant to carbide
precipitation and can be heated into the above temperature range.
Grade 304H has higher strength at elevated temperatures so is often used for structural and pressure-containing applications at
temperatures above about 500°C and up to about 800°C. 304H will become sensitised in the temperature range of 425-860°C; this is
not a problem for high temperature applications, but will result in reduced aqueous corrosion resistance.
Heat Treatment
Solution Treatment (Annealing) - Heat to 1010-1120°C and cool rapidly. These grades cannot be hardened by thermal treatment.
Welding
Excellent weldability by all standard fusion methods, both with and without filler metals. AS 1554.6 pre-qualifies welding of 304
with Grade 308 and 304L with 308L rods or electrodes (and with their high silicon equivalents). Heavy welded sections in Grade
304 may require post-weld annealing for maximum corrosion resistance. This is not required for Grade 304L. Grade 321 may also be
used as an alternative to 304 if heavy section welding is required and post-weld heat treatment is not possible.
Machining
A "Ugima" improved machinability version of grade 304 is available in bar products. "Ugima" machines significantly better than
standard 304 or 304L, giving higher machining rates and lower tool wear in many operations.
Dual Certification
It is common for 304 and 304L to be stocked in "Dual Certified" form, particularly in plate and pipe. These items have chemical and
mechanical properties complying with both 304 and 304L specifications. Such dual certified product does not meet 304H
specifications and may be unacceptable for high temperature applications.
Applications
• Food processing equipment, particularly in beer brewing, milk processing & wine making.
• Heat Exchangers
• Threaded fasteners
• Springs