ADDENDUM No.! 6 Pages 11/06
CRANE LOAD CHART BASICS
LOAD CHARTS
TMS300B
PCSA CLASS 10-114
85% STABILITY
73,600 Ib GVW
With power Pinned Fly
and 32ft Boom Extension
71321
SERIAL NUMBER
Grove40 1 of 610,
"
12,
13,
14
15
GENERAL NOTES
Do not exceed any rated lifting capacity. Rated lifting capacities are based on freely suspended loads with the
machine leveled and standing on a firm supporting surface. Ratings with outriggers are based on outriggers being
‘extended to their maximum position and tires raised free of crane weight before extending the boom or lifting loads.
Practical working loads for each particular job shall be established by the user depending on operating conditions
to include: the supporting surface, wind and other factors affecting stability, hazardous surroundings, experience of
personnel, handling of load, etc. No attempt must be made to move a load horizontally on the ground in any direction,
Operating radius is the horizontal distance from the axis of rotation before loading to the centerline of the vertical
hoist line or tackle with loads applied
"On Rubber" lifting (if permitted) depends on proper tire inflation, capacity and condition. “On Rubber" loads may
be transported at a maximum vehicle speed of 2.5 mi/hr (4 km/hr) on a firm and level surface under conditions
specified.
Jibs may be used for single line lifting crane service only. Jib capacities are based on structural strength of jib or
main boom. Jib loads must not exceed main boom lifting capacities for the actual operating radius.
Operation is not intended or approved for any conditions outside of those shown hereon. Handiing of personnel
from the boom is not authorized except with equipment furnished and installed by Grove Manufacturing Company.
For clamshell or concrete bucket operation, weight of bucket and load must not exceed 80% of rated lifting capacities,
Power-telescoping boom sections must be extended equally at all times. Long cantilever booms can create a tipping
condition when in extended and lowered position,
‘The maximum load which may be telescoped is limited by hydraulic pressure, boom angle, boom lubrication, etc.
It is safe to attempt to telescope any load within the limits of rated lifting capacity chart
With certain boom and hoist tackle combination, maximum capacities may not be obtainable with standard cable
lengths
With certain boom and load combinations, raising of load with boom lift cylinders may not be possible. Operational
safety is not affected by this condition
Keep load handling devices a minimum of 12 inches (30 cm) below boom head when lowering or extending boom
If actual boom length and/or radius is between values listed, use lifting capacity for the next longer rated length
and/or radius.
All load handling devices and boom attachments are considered part of the load and suitable allowances must be
made for their combined weights.
Operation of this equipment in excess of rating charts or disregard of the instructions is hazardous and voids the
warranty and manufacturers liability.
LIFTING CAPACITY NOTES
Capacities appearing above the bold line are based on structural strength and tipping should not be relied upon as
a capacity limitation. Capacities do not exceed 85% of tipping loads as determined by test in accordance with SAE
recommended practice-Crane load stability test code - SAE J-765.
Do not exceed any rated load when lifting regardless of whether it is based on structural strength or stability,
For boom lengths less than 104 ft. with power pinned fly extended, the rated loads are determined by boom angle
only in the column headed by 104 ft. boom. For boom angles not shown, use rating of next lower boom angie.
For boom lengths less than 113 ft. with power pinned fly retracted and 32 ft. boom extension erected, the rated
loads are determined by boom angle only in the column headed by 113 ft. boom. For boom angles not shown, use
rating of next lower boom angle.
For boom lengths less than 136 ft. with power pinned fly extended and 32 ft. boom extension erected, the rated
loads are determined by boom angle only in the column headed by 136 ft. boom. For boom angles not shown, use
rating of next lower boom angle.
Boom angle is the included angle between horizontal and the axis of the boom base section after lifting rated toad.
* Capacities for the 34 ft. boom length shall be lifted with boom fully retracted. If boom is not fully retracted,
capacities shall not exceed those shown for the 38 ft. boom length.
NOTE: If machine is equipped with front jack cylinder, the front jack cylinder shall be set in accordance with written
procedure. Radii less than 35 ft. not recommended when lifting over front of machine.
tms3008 - S/N 71321 Grove40 2 of 6RATED LIFTING CAPACITIES IN POUNDS
34 ft. - 104 ft. BOOM
ON OUTRIGGERS - 360°
Radius a me 73 wa
in eet ‘ain Boom Langan in Feat (Power Pinned Fiy Revered) Power Pin [57h Ox @ [SDR Exe
ryeark | srk | oer
SS CS 104 nH 136
70 80.006 [68.000 | 6a.000 | 60.000 See See See
o)_| as) | as) | 05) Warning _| Warning | _wovning
77} 65.000 [62.500 [57-500 | ss 000 [s7,000 | 49,000, Note3 | Nowe4 —]— Notes
es) |» fare | oo | ce | ors
TE 67.000 [5.000 | 50.000 | 46.500 [43.900 [1.900 | 40,000 | 38.600
ws] ea | 675) | G08 | 7 | 748) | 6H) | 78)
3) [ae.a0 [43,000 | 39.500 | 36.500 [34.500 | 32.700 | 3t.400 | 30,000 | 78.700
25) Loe | oo | oo | 7s) | 09 | 02 | vas | 06
3] 25.460 [ 20480 | 2.480 | 29-450 | 20,700 | 26.500 | 25,00 | 28,200 | 75.100 | 70,000 | 17500
ess) | ws | 6a [ors Lorn | on [ers | eas | va | an | 7s,
35] 20.560 | 201560 | 70.560 | 20.580 [20,800 [20,500 | 20,500 ] 20,000 | 19,000 | 17.750 | —¥6.400
oa [an | «x | eo [5 | 695 | ze Loss | oy | cas | 55)
3% T5480 | 15.460 | 16450 | 15460 | 15.450 | 18460 | T8480] 15600 | 12.700} 8.600
crs | a2 | a | Go | ors | on oss | or | o9 | ors
a tao firaio [i410 [irate Pirato | 11410] 11410 | 13.100 | 12.200 | 8.750
03s) | a2 | ats | a7) | 62) | es | eo | es | cos) | 55)
5 3450 | 8480 | 8a60 | e460 | 8.450 | 8480 | 10990 | 10.800 | 7.900
ce [2s | an | an [ors | oo | oss |r) 7s
50 6630 | 6530 | 6630 | 6630 | 6630 | 8760 | —ea70 | 7.050
cos) | 3 | aos | wo | ors) | 2 | ess | on
% 260 | 6260 | 5260 | 6,260 | 7.130 | 7300 | 650
@s |e | lues| oo | ors | oss
% “090 | a.090 | 4.090] 5.650] 5.00] 5800
@ [ess | en | oss | es) | es
w 060 [3080 | 3.000] 4500 | —a760 [8190
@ | 2) [a | a | sss) | eas)
7 2180 | 2180 | 3600 [3700 | «440
ars ars | a] o28)_| or)
7% 1.300 | 2.840} 3.000 | 3.650
Gn | as us| 685)
7 2189} 2.340] 2.950
(40) (48) (56)
s 1880} 1.740 | 2.370
(35) cn | 1635)
% 7.020 [1.170 | 1.990
ess | on | 60s)
ro 1530
(ers)
105 7.130
(4a)
Note: Boom angles ate in dagrees.
{LMI operating code, Refer ro LMI manual for instructions,
‘Soe
ing capectty nates on page 2
TMs3008 S/N 71321
Grove40 3 of 6
‘AS. 829-006678 & -0021370RATED LIFTING CAPACITIES IN POUNDS
34 ft. - 104 ft. BOOM
ON OUTRIGGERS - OVER REAR
Radius #01 102 708 108
In Feet ‘Main Boom Length in Feet (Power Pinned Fly Retracted) PoworPin [32h em 6 [32h Ex
Fyesth | et toa fe
734 38 [50 5S 2 mo 7 a 104 cE 136)
70 | 86.000 [68.000 | 64.000 | 60,000 ‘See See ‘See
wx) | ors) | 745) | 65) warring | Warring _|_Wornng
72 [65.000 [62.500 | 57.500 | $4,000 ] 67.000 | 49.000 Noes | Noted | Notes
wos) | 6) | 715) | a | 7) | 075)
Ts [57.000 [5,000 | 50.000 [46,500 | 43,900 | 41,900 | 40,000 | 38,500
was) | | 675) | vos) | va _| 748) | ves) | 75)
720___[ 47,000 | 43.000 | 39.500 | 36,600 [34.500 | 32.700 | 31,400 | 30,000 | 28.700,
was) | a) | 60) | we [ers | co | 72 | 735) | ce
"25 | 35.675 | 33.300 [31,000 | 30,000 [ 28.100 | 28.500 | 25.300 | 24.200 | 23,100 | 20,000 | 17,500
(355) | 1a) | 62) | 675) | ors | sr | 675) | 95) | ca | 78)
30 [25.200 | 25.200 | 26.200 | 26.200 | 23.600 | 22.100 ] 21,000 | 20,000 | 19,000 | 17,750 | 15.400
oa fan | cay | 50] 55.5} 1595) | (os) | v5.5) | cee) | 1745) 75.5)
35 78.340 | 18.340 | 19,340 | 18700 | 17,700 | 16.800 | 16,000] 16600 | 13,700 | 9600
ars) | a2 | 4 Leo Lore] en | es | ors (73 075)
0 15.180 | 15.190 | 15180 | 18190 ] 16,190 | 14400 [13.600 } 1s100 | 12200 | 6750
«i35) | 2 | 1) | 475) | 25) Les) | (6 | 685) (705) (755)
% ¥2310 [12310 | 210 | 12.310 | asi | 11,700 | 11,300 | 10800 | 7.900
cr) | 25) | an | a7 | 15) | eo | ess) (675) (73)
0 70,000 | 70.000 | 70.000 [10,000 | 10.000 | 9.830 aa10 7050
os) | xy | aos) | cae) _| 515) | (62) (645) my
oF 3.180 | 8180 | 8180 | 8.180 | 8710 8230 6.360
25) | 33)_| (oy | 465) | 9) 61.5) (68.5)
0 650 | 6.650 | 6.650 | 7.680 7280) 5.800
ea | ass) | ay | 655) (585) (65)
cy 280 | 5.280 | 5280 | 6,800 6.380) 5.200
@ |e | os | 2 wssy | (635)
7 4.140 | 4.140 5580 4750
1) | 275) 525) 615)
75 3320 | 6000 ‘310, 4360
an | ws (aa) (585)
oy 4.060 090) 4.050
(40), (49), (56)
co 3.290 3.420 3.700
(35) cay (535)
30 2.730 2,830 3.280
(298) 3”) (50.5)
% 2210 2.330 2.870
(225) (32) 275)
700 7.680) 7.290 2.470
305) es) | 445)
105 1470 2.080)
os) cy
70 1700
(375)
Te 1.380)
(335)
120 7070)
(29)
‘Note: Boom angles are in dearaos "A6-829-0083008 6 0021370
{HLM operating code. Refer 10 LM manual for instructions
‘See iting capacity notes 06 page 2
Tms3008 S/N 71321 Grove40 4 of 62OLo Lines DETERMINE
Charing positron oe AF
OAD fo, OPERATION WITHIN,
NOMCING AREAS INDICATED!
WORKING AREA DIAGRAM
SENTERO
RetaTION
LINE PULLS & REEVING INFORMATION
HOISTS: CABLE SPECS, PERMISSIBLE
LINE PULLS:
MAIN & AUX. [3/4 in. (19 mm) 18x19 Class or 35x7 12,920 Ibs.
Mode! 30 Rotation Resistant
Min. Breaking Str. 64,600 Ibs.
WEIGHT REDUCTIONS FOR LOAD HANDLING DEVICES
*Stowed -
‘Erected -
HOOKBLOCKS:
150 Ton, 4 Sheave
45 Ton, 3 Sheave
15 Ton, 1 Sheave
25 Ton, 2 Sheave
Ausliary Boom Hoad
10 Ton Headache Ball
7.1/2 Ton Headache Ball
Tws3008 - S/N 71321
32 ft. Boom Extension
430 Ibs.
2,985 Ibs.
"Reduction of main boom capacities
700 Ibs.
1,100 tbs.
400 i,
665 is,
100 tbe.
1560 ibs
328 hs
When lifting over swingaway and/or jib
combinations, deduct total weight of all
load handling devices reeved over main
boom nose directly from swingaway or jib
capacity.
NOTE: All load handling devices and boom
attachments are considered part of the load
and suitable allowances MUST BE MADE
for their combined weights. Weights are for
Grove furnished equipment.
Grove40 5 of 6HOOK ELEVATION IN FEET
RANGE DIAGRAM CUNLADEN BOOM) 06-829-008865
G'
180
170
160
150
Wao S2a5
130
120 32"
110 104
100
90 81
74
68
62
56
50
44
80
70
60
BOOM & EXTENSION LENGTH IN FEET
so
40
30 75* MAX
20
10 o
iso | 130 | 110 | 90 | 70 | So |. 30
1603 2140)! 120) = 1001. 80 60) = 40: 20)
AXIS_OF
ROTATION
OPERATING RADIUS FROM AXIS OF ROTATION IN FEET
DIMENSIONS ARE FOR LARGEST
tT GROVE FURNISHED HOOK BLOCK
AND HEADACHE BALL, WITH
ANTI-TWO BLOCK ACTIVATED
= WITH 81 FOOT 800M ux WITH 104 FOOT BOOM
TMS3008 S/N 71321
Grove40 6 of 6