Professional Documents
Culture Documents
Duct Seal: Multi Cable and Pipe Sealing System
Duct Seal: Multi Cable and Pipe Sealing System
Duct Seal: Multi Cable and Pipe Sealing System
UK
THORNE & DERRICK UK
TEL 0044 191 490 1547 FAX 0044 477 5371
TEL 0044 117 977 4647 FAX 0044 977 5582
WWW.THORNEANDDERRICK.CO.UK
Duct Seal
Multi Cable and Pipe Sealing System
SAFETY.
RELIABILITY.
INGENUITY.
Features.
Simple and Effective Water and Gas Tight Flexible and Versatile
The RISE Duct Seal is a multi-cable The elasticity and high bonding The RISE System can be used
and pipe transit sealing system. strength of FIWA sealant offers in vertical as well as horizontal
It provides an effective and simple a flexible seal, which resists ducts. The insert sleeves cling
solution to all fire, gas and watertight movement, shock and vibration, to the cables without sliding down
duct sealing requirements. as well as high pressure. The RISE and falling out of the penetration.
rubber insert sleeves are applied The high adhesion and viscosity
Few Components to provide cable separation and of the FIWA sealant means
a backing for the application of the it will not run or drip when
It consists of only two components:
FIWA sealant. For water and gas applied overhead.
rubber insert sleeves, used to
tight applications our standard
separate the cables and as a backing
60mm RISE sleeve is sufficient. Adding/Removing Cables
for the sealant layer and FIWA
sealant; a high quality silicone based, Installing additional cables is very
Fire, Water and Gas Tight
fire resistant, water repellent sealant straightforward. It is a simple matter
which consequently makes the Using the RISE insert sleeves at of coring into the soft rubber layer
system quick and easy to install. a length of 160mm and applying of the FIWA sealant to a depth of
FIWA sealant to both faces of the 20mm and passing the additional
opening, will provide a fire tight seal. cables through the opening created.
When exposed to heat or flame, The FIWA sealant is then applied
the advanced rubbers used within around the new cable to re-seal.
the system will resist heat and flame, There is no need to disassemble
assuring total conduit sealing the whole transit.
protection against fire, heat,
toxic and corrosive gases.
2 csdsealingsystems.co.uk
Benefits.
20 60
20mm layer FIWA sealant Concrete
*wall/floor thickness
2 x 20mm FIWA sealant minimum 180mm 20 160 20
layers 160mm RISE insert for F180 Concrete
sleeves Type FRR/LEHF
• Certified Pressure
Resistance - 2.5BAR
• 4 hours fire protection
5
Installation.
Clean the inside of the duct Fill the remaining free space with Apply a 20mm layer of FIWA
and cables, use an appropriate spare RISE insert sleeves, usually sealant to the face of the transit.
degreaser to remove the dirt, dust of sizes 27/19 and 18/12. Pack Begin in the most difficult area
or oil to allow the FIWA sealant sleeves tightly then adjust to and work outwards. A slight
to bond. Apply a RISE insert allow a 20mm gap from the front overfill is recommended.
sleeve of the relevant diameter of the transit.
around each cable.
Using a damp cloth, press the Using your hand (gloves are Take a final check with a torch
FIWA sealant down and between recommended), make sure to ensure sufficient FIWA sealant
the cables. Ensure a sufficient enough sealant is between has been applied between
amount is applied and it makes the cables and has been the cables. FIWA sealant layer
good contact with all surfaces. applied to the required depth cures on average at a rate
and then smooth to finish. of 2mm per day.
Wet the hands to prevent
the FIWA sealant sticking.
6 csdsealingsystems.co.uk
Adding a cable.
Adding extra cables Pull the cable through If the empty filler Pull the cable through
is an easy job. Cut one of the empty filler sleeves are not fitting the fitting insert sleeve
away the sealant layer sleeves with an inner to the size of the cable that has now been
at both sides of the diameter more or less to be ducted, a number installed. Refill the
penetration with corresponding to the of these insert sleeves openings cut in the
a knife or a hollow outer diameter of must be removed sealant layer at both
punch in a tapering the cable. from the penetration. sides of the
shape as shown penetration with
Refill the opening in Install a fitting insert
above. This creates sufficient sealant.
the sealant layer at sleeve (with some filler
a good foundation The sealant is
both sides of the sleeves if necessary)
for the sealant mass pressed down firmly
penetration with in the open space
to be applied later. and smoothed with
sufficient sealant. in the penetration.
a damp cloth.