Professional Documents
Culture Documents
Troubleshooting: 7.1 Power Supply Section
Troubleshooting: 7.1 Power Supply Section
0U LA
7. TROUBLESHOOTING
7.1 Power Supply Section
FLOW CHART NO.1
The power cannot be turned on.
No
Is the fuse (F1901) normal? See FLOW CHART No.2 <The fuse blows out.>
Yes
Is normal state restored when once unplugged No
Check if there is any leak or short-circuiting on the
power cord is plugged again several seconds?
primary circuit component, and service it if defective.
Yes (C601, D1901, D1902, D1903, D1904, Q601, Q603,
No T601)
Is the AL +13V line voltage normal?
Yes
Check the presence that the primary component Check the presence that the rectifying diode or circuit
is leaking or shorted and service it if defective. is shorted in each rectifying circuit of secondary side,
and service it if defective.
Does the photocoupler circuit on the No Check IC603, D631, Q631 and their periphery,
secondary side operate normally? and service it if defective.
Yes
Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side,
and service it if defective. (IC637, D503, D632, D633, D636, D637, D638, D639, D640, D647, D669)
Is approximately 40V voltage supplied to the No Check C639, D636 and their periphery circuit, and
cathode of D636? service it defective.
Yes
Is approximately 13V voltage supplied to the No Check C638, D638, D639 and their periphery circuit,
cathode of D638? andservice it defective.
Yes
Is approximately 6.6V voltage supplied to the No Check C654, D669 and their periphery circuit, and
cathode of D669? service it if defective.
Yes
No
Is approximately 6.6V voltage supplied to the See FLOW CHART No.7
collector of Q637?
Yes
No
Is approximately 6V voltage supplied to the See FLOW CHART No.10
base of Q637?
Yes
Replace Q637.
Is approximately 36V voltage supplied to the No Check C639, D636 and their periphery circuit, and
cathode of D636? service it if defective.
Yes
Is approximately 36V voltage supplied to the Yes Check D641, D652 and their periphery circuit, and
collector of Q632? service it if defective.
No
Is the voltage of base on Q632 lower than the No Check Q634 and P-ON-H1 line, and
voltage of emitter on Q632 when turning the service it if defective.
power on?
Yes
Replace Q632.
26 FUZ2.0U LA
Is approximately 15V voltage supplied to the No Check C633, D633 and their periphery circuit, and
cathode of D633? service it if defective.
Yes
No
Is approximately 14V voltage supplied to the See FLOW CHART No.9
base of Q645?
Yes
Replace Q645.
Is approximately -9V voltage supplied to the No Check C663, D637 and their periphery circuit, and
anode of D637? service it if defective.
Yes
No
Is approximately -9V voltage supplied to the See FLOW CHART No.9
base of Q646?
Yes
Replace Q646.
Is approximately 5V voltage supplied to the No Check C634, D632 and their periphery circuit, and
cathode of D632? service it if defective.
Yes
Is approximately 4V voltage supplied to the No Check Q639, Q671 and their periphery circuit, and
base of Q638? service it if defective.
Yes
Replace Q638.
Is approximately 3V voltage supplied to the No Check C664, D647 and their periphery circuit, and
cathode of D647? service it if defective.
Yes
Check if there is any leak or short-circuit on
the loaded circuit, and service it if defective.
FUZ2.0U LA 27
Is approximately 3V voltage supplied to the No Check C642, D640 and their periphery circuit, and
cathode of D640? service it if defective.
Yes
No
Is approximately 13V voltage supplied to the See FLOW CHART No.6
collector of Q801?
Yes
No
Is approximately 10V voltage supplied to the See FLOW CHART No.10
base of Q801?
Yes
Replace Q801.
Are the contact point and installation state of the key Re-install the switches (SW108, SW109, SW110,
No
switches (SW108, SW109, SW110, SW111, SW111, SW112, SW113, SW114) correctly or
SW112, SW113, SW114) normal? replace the poor switch.
Yes
When pressing each switches (SW108, SW109, Check the switches (SW108, SW109, SW110,
SW110, SW111, SW112, SW113, SW114) do the No
SW111, SW112, SW113, SW114) and their
voltage of Pin(1) on CN301 increase? periphery, and service it if defective.
Yes
Replace Digital Main Board Unit.
28 FUZ2.0U LA
Is the "L" pulse sent out Pin(1) terminal of receiver No Replace the infrared remote control receiver
(RCV101) when the infrared remote control is (RCV101) or the remote control unit.
activated?
Yes
Is the "L" pulse supplied to the Pin(4) of CN301? No Check the line between Pin(1) terminal of receiver
(RCV101) and Pin(4) of CN301 , and service
Yes
it if defective.
Replace Digital Main Board Unit.
Are the video signals outputted to the specific Check the line between each pin of CN302 and input
terminal? terminal and service it if defective.
Are the video signals outputted to the No Check the video signal line and IC7001,
Pin(23) of CN302? and service it if defective.
Are the luminance signals outputted to the No Check the luminance signal line and IC7001,
Pin(19) of CN302? and service it if defective.
Are the chrominance signals outputted to the No Check the chrominance signal line and IC7001,
Pin(21) of CN302? and service it if defective.
Are the component video(Y/Pb/Pr) signals outputted No Check the component video(Y/Pb/Pr) signal line
to the Pin(14, 16, 17) of CN302? and IC7001, and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(14,15) No Check IC701 and the periphery circuit,
of IC701? and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(1,7) No Check IC702 and the periphery circuit,
of IC702? and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(1,2) No Check IC801 and the periphery circuit,
of CN801 and CN802? and service it if defective.
Yes
Are the DIF signals outputted to the Pin(20, 22) No Check the line between Pin(20, 22) of CN303 and
of CN303? Pin(20, 21) of TU1 and TU1(Tuner Unit),
Yes and service it if defective.
No
Are the audio data signal outputted to the Pin(6) of Replace Digital Main Board Unit.
CN302?
Yes
Are the audio(L/R) signals outputted to the Pin(14,15) No Check IC701 and the periphery circuit,
of IC701? and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(1,7) No Check IC702 and the periphery circuit,
of IC702? and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(1,2) No Check IC801 and the periphery circuit,
of CN801 and CN802? and service it if defective.
Yes
Are the audio (L/R) signals outputted to the No Check the line between Pin(3, 4) of CN303 and
Pin(3, 4) of CN303? each Audio input terminal(JK752, JK7501, JK7702,
Yes JK7705, JK7712, JK7714), IC7001 and IC7301, and
service it if defective.
No
Are the audio data signal outputted to the Pin(6) of Replace Digital Main Board Unit.
CN302?
Yes
Are the audio(L/R) signals outputted to the Pin(14,15) No Check IC701 and the periphery circuit,
of IC701? and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(1,7) No Check IC702 and the periphery circuit,
of IC702? and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(1,2) No Check IC801 and the periphery circuit,
of CN801 and CN802? and service it if defective.
Yes
IC3101
(SUB MICRO CONTROLLER)
X3101
XOUT 6 4MHz
8.1 System Control Block Diagram
12 LED1
XIN 8 OSC
24 KEY-IN1
13 P-ON-H2
IC3102 (MEMORY)
14 P-ON-H1
REMOTE R22 11 REMOTE SDA 20 5 SDA
TO AUDIO-1 INPUT0 TXD1 P22 15 RXD SCL 19 6 SCL
A11 INPUT0
BLOCK INPUT1 RXD1 N22 16 TXD WP 2 7 WP
DIAGRAM E12 INPUT1
RESET-MAIN V24 5 RESET-MAIN
TO DIGITAL
VCOM-PWM SIGNAL
VCOM-PWM 21 PROCESS
BLOCK
AMP-MUTE-MAIN C12 18 AMP-MUTE-SUB DIAGRAM
3 RESET POWER SUPPLY BOARD
CN3701 CN302
PROTECT1 TO POWER
8. BLOCK DIAGRAM
RESET TO AUDIO-2
X3301 AMP-MUTE BLOCK
U25 CLKOUT DIAGRAM
25MHz
OSC U26 CLKIN
BOARD
31
“ “ = SMD
32
IC7001
JK752 POWER SUPPLY BOARD (VIDEO SELECTOR) DIGITAL MAIN BOARD UNIT
VIDEO-IN2
CN751 CN701 56
5 VIDEO-IN2 5 6
FUZ2.0U LA
JK7702
VIDEO-IN1
C Y
JK7701
S-VIDEO
-IN1
3 S-SW1
9 S-SW2
JK7711
COMPONENT
-Y-IN1
COMPONENT
-Pb-IN1
COMPONENT
-Pr-IN1
JK7713
COMPONENT
-Y-IN2
COMPONENT
-Pb-IN2
COMPONENT
-Pr-IN2
TU1
(TUNER UNIT)
CN303 CN3704
DIF-OUT1
DIF-OUT1 20 22 DIF-OUT1 2 TO DIGITAL
DIF-OUT2 SIGNAL
DIF-OUT2 21 20 DIF-OUT2 4
IF-AGC PROCESS
IF-AGC 18 18 IF-AGC 6 BLOCK
Q3 TU-CVBS DIAGRAM
VIDEO-OUT 4 BUFFER 11 TU-CVBS 13
“ “ = SMD
AUDIO SIGNAL
AUDIO(R)
-IN2 IC7001
(AUDIO SELECTOR)
53
SIDE JACK BOARD
51 AUDIO 45
49 SELECTOR
47
8.3 Audio-1 Block Diagram
JK7702
AUDIO(L) IC7301 IC3702
-IN1 (INPUT SELECT) (AUDIO A/D CONVERTER)
WF7
AUDIO(R) 4
-IN1 CN303 CN3704 BCLK TO
2 (L-CH) 11
3 3 AUDIO(L) 21 1 LRCLK DIGITAL
5 A/D 10 SIGNAL
4 AUDIO(R) 20 (R-CH) CONVERTER ACLK PROCESS
JK7712 15
2 AUX-ADATA BLOCK
COMPONENT 12 DIAGRAM
AUDIO(L) 54
-IN1 52 AUDIO 44 11
COMPONENT 50 SELECTOR
AUDIO(R) 15
48 13
-IN1 14
JK7714
COMPONENT
AUDIO(L) SW CTL
-IN2
COMPONENT
AUDIO(R) 9 10
-IN2
JK7501
PC-AUDIO
-IN
Q7301
JK7705
Q7302
HDMI
AUDIO(L)-IN
HDMI
AUDIO(R)-IN
CN303 CN3704 TO
TU1 INPUT1 SYSTEM
(TUNER UNIT) 7 INPUT1 17 CONTROL
INPUT0
Q4,Q5 8 INPUT0 16 BLOCK
DIAGRAM
SIF-OUT 3 BUFFER 9 SIF 15
TO
DIGITAL
SIF SIGNAL
FUZ2.0U LA
PROCESS
BLOCK
DIAGRAM
33
“ “ = SMD
34
AUDIO SIGNAL
IC701
(AUDIO D/A CONVERTER) P-ON+9V
IC702
(AMP)
CN801 CL801
CN3701 CN302 PWM SP801
LRCLK 3 8,9 2 SP(L)+
TO 14 LRCLK 10 8 (L-CH) 1 2 GEN. SPEAKER
DIGITAL BCLK 15 2 18,19 1 SP(L)- L-CH
15 BCLK 9 7 D/A
SIGNAL ADATA
PROCESS 16 ADATA 8 6 CONVERTER (R-CH)
BLOCK ACLK 14
17 ACLK 7 5
DIAGRAM SPDIF 5 44,45
18 SPDIF 6 7 51 PWM
6 -1 34,35
12 AMP-MUTE 12 GEN.
20 RESET 4
8.4 Audio-2 Block Diagram
P-ON+5V
Q7201 JK7715
BUFFER DIGITAL
AUDIO-OUT
(COAXIAL)
TO POWER
RESET SUPPLY
BLOCK
DIAGRAM
45 37 B0(+)
SIF 44 36 B0(-)
AUX-ADATA 42 35 G3(+)
TO AUDIO-1 AD15
BCLK 41 34 G3(-)
BLOCK AE15
DIAGRAM LRCLK DIGITAL
AE16 SIGNAL 40 33 G2(+)
ACLK AUDIO I/F PROCESS 39 32 G2(-)
AF15
RSDS 38 31 G1(+)
SPDIF
AF16 I/F 37 30 G1(-)
ADATA
AD16 36 29 G0(+)
TO AUDIO-2 BCLK
BLOCK 35 28 G0(-)
DIAGRAM LRCLK
31 23 R3(+)
JK4001 ACLK
30 22 R3(-)
TMDS-D0(+) 29 21 R2(+)
7 A9
TMDS-D0(-) 28 20 R2(-)
9 B9
TMDS-D1(+) AUDIO 27 19 R1(+)
4 C8 DECODER
TMDS-D1(-) 26 18 R1(-)
6 C9
TMDS-D2(+) 25 17 R0(+)
1 B8
HDMI-IN1 TMDS-D2(-) 24 16 R0(-)
3 A8
TMDS-CLOCK(+) 33 26 CLK(+)
10 B10
TMDS-CLOCK(-) 32
1 25 CLK(-)
12 A10
SDA Q4002 IC4202 (MEMORY) 22 52 STH
16 BUFFER E9
SCL 92 5 CPV
15 BUFFER C10
SCL 6 99 SCL 93 4 GOE
Q4001
HDMI VIDEO SDA 5 100 SDA 19 54 LP
JK4002 I/F DECODER
53 POL
TMDS-D0(+) 6 STV
7 A5
TMDS-D0(-) SWITCHING 1 VGH
9 B5
TMDS-D1(+) Q4501, Q4516,
4 C4 IC3201 (SDRAM)
TMDS-D1(-) Q4551, Q4552
6 C5
TMDS-D2(+)
HDMI-IN2 1 B4 A13-15,A18, B1,B9,C2,C8,
TMDS-D2(-) D1,D3,D7,D9,
3 A4 A21-23,B13-15,
TMDS-CLOCK(+) B17,B19-23 F1,F9,G2,G8, DATA(0-15)
10 B6 H1,H3,H7,H9 IC4511, Q4511,
TMDS-CLOCK(-) TO SYSTEM Q4512, Q4513
12 A6 C15,C17-19, M2,M3,M7,M8,
FUZ2.0U LA