Professional Documents
Culture Documents
SCH Linea Screen Bidi 02 en
SCH Linea Screen Bidi 02 en
SCH Linea Screen Bidi 02 en
BiDirectional radio
automation and
management systems
for blinds, rolling shutters
and awnings
Nice
Command
reception feedback
blind/shutter wound
blind/shutter unwound
partial opening/closing
> ERA P BD, ERA W BD > ERA INN EDGE BD > DMBD GW > TTPRO BD
Portable and wall-mounted For indoor blinds Bidirectional din module Palmtop programmer for tubular
transmitters Tubular motors with electronic limit The DMBD GW module acts as an motors
Ergonomic design and intuitive use for switch, practical dry contact input and interface between the modular system Time savings and incomparable
this line of transmitters to control blind, built-in bidirectional radio receiver. and the Nice bidirectional transmitters: precision. The TTPRO BD simplifies
rolling shutter and awning automations. it can memorise up to 30 radio channels management of blind and rolling shutter
With key to activate/deactivate the with a frequency of 433.92 MHz and automation systems: programming is
climatic sensor, “i” key to check blind manage all outputs in the control system. simple, by memorising the settings then
position and slider for the “Go to > ERA FIT M BD copying them without repeating the
Position” function. sequence for each new automation.
Available in one and six channel version. For outdoor blinds No access to the automation is required:
Up to six groups of automations can be and rolling shutters you can control and programme Nice
controlled in single, group, or multigroup and awnings automations with bidirectional radio
mode. Tubular motor with without needing physical access to the
electronic motor itself. Installation is completely
limit switch and built- wireless.
in bidirectional radio receiver.
BiDi Yubii
Era P BD series
Portable bidirectional transmitters
Down
Slider
Era W BD Series
Wall-mounted bidirectional transmitters
PRG Esc
key key
LED to select
the channel and
display command
reception Group selection keys
feedback
Up Easy duplication, just place the two transmitters Intuitive programming procedure using the Fully concealed wall support included in pack
near each other and press a key keys on the back of the transmitter
Stop
Down
Era Fit M BD
E FIT M 817 BD Electronic limit switch, built-in bidirectional radio receiver. 1
8 Nm, 17 rpm, 15 kg*
E FIT M 1517 BD Electronic limit switch, built-in bidirectional radio receiver. 1
15 Nm, 17 rpm, 28 kg*
With limit switch and built-in bidirectional E FIT M 3017 BD Electronic limit switch, built-in bidirectional radio receiver.
30 Nm, 17 rpm, 56 kg*
1
radio receiver E FIT M 4012 BD Electronic limit switch, built-in bidirectional radio receiver.
40 Nm, 12 rpm, 75 kg*
1
TECHNICAL SPECIFICATION
Code E FIT M 817 BD E FIT M 1517 BD E FIT M 3017 BD E FIT M 4012 BD E FIT M 5012 BD
ELECTRICAL SPECIFICATIONS
Power supply (VAC/Hz) 230/50
Absorption (A) 0.55 0.75 1.10
Power (W) 120 170 250 245 250
Power consumption in standby (w) <0,5
PERFORMANCE
Torque (Nm) 8 15 30 40 50
Speed (rpm) 17 12
Lifted weight* (kg) 15 28 56 75 95
Number of turns before the stop 92
Continuous operating time (min) 4
DIMENSIONAL DATA
Tubular motor with electronic limit Thanks to this function, there are a number of possible Length (L) (mm) 426 451 486
settings.
switch and built-in bidirectional radio If an incorrect selection is made, programming begins
Weight of motor (kg) 2.15 2.45 2.65
Pack dimensions (mm) 90x90x465 90x90x500 90x90x530
receiver. again from the previous level without the need to
reprogramme all the settings programmed up to that Protection class IP44.
point. *Value calculated with 60 mm diameter octagonal roller.
M size - 45 mm.
Memory locking to prevent accidental memorising.
Smart Connection to climatic sensors via radio with user- POWER CABLE
The Nice bidirectional radio protocol enables friendly programming.
Length 2.5 m, 3 wires in cable
confirmation of correct reception of the command by the
The built-in circuit board allows a number of motors PHASE
automation and the possibility of checking the position
to be connected and controlled in parallel CA0274A00
from a NEUTRAL
of the blind or rolling shutter. As it also supports the Nice EARTH
single point without the need for additional control units.
mesh network function, the motor can route the radio
command, thus extending the radio range of the system. Low consumption in stand-by.
CA0275A00
Handy remote control of limit switches by
transmitter in manual or semi-automatic mode. DIMENSIONS
Compatible with previous versions of Nice unidirectional transmitters.
Easy to programme, thanks to feedback CA0276A00 15 L
from movement of the rolling shutter.
Ø 8
2,25 17
Ø5
Ø
Level programming: quick and safe. 31,5 Ø1
48
3,
2
5
CA0277A00
44,9
Ø45
Ø30
CA0278A00
3,5
,8
17
60
Ø
ax
m
BiDi Yubii 100-240 Vac Code Description Pcs./pack Certificates
For indoor blinds, with built-in E EDGE SI 1012 AC BD Electronic limit switch, dry contact and built-in radio receiver.
100-240 VAC, 10 Nm, 12 rpm
1
bidirectional radio receiver NB: When ordering, please specify the certification required.
TECHNICAL SPECIFICATION
Code E EDGE SI 332 AC BD E EDGE SI 620 AC BD E EDGE SI 1012 AC BD
Pushbuttons for precise
and quick limit switch adjustment ELECTRICAL SPECIFICATIONS
Antenna cable Power supply (VAC/Hz) 100-240 / 50-60
Connectors for dry contact Absorption (A) 0.6 0.8
input
Power (W) 40 50 40
Power consumption in standby (W) <0.5
PERFORMANCE
Torque (Nm) 3 6 10
Rated speed (rpm) 32 20 12
Maximum speed (rpm)* 48 32 20
Minimum speed (rpm) 16 10 5
Noise (dBA)** 35
Number of turns before the stop <150
Continuous operating time (min) 10 6
Lifted weight (kg)*** 12 22 34
DIMENSIONAL DATA
Length (L) (mm) 744
Cable length (m) 1.5
Tubular motor with electronic limit Adjustable up and down speed.
Weight of motor (kg) 1.5
switch, practical dry contact input Compatible with commercially available dry contact Operating temperature (°C Min/Max) 0 - 60
and built-in bidirectional radio systems. Pack dimensions (mm) 795x100x100
receiver. Simple installation Protection class IP30.
*If the set speed is higher than the rated speed, motor torque is automatically reduced by 50%.
Each motor can be programmed individually, without **Noise levels have been measured in accordance with EN ISO 3745, EN ISO 3746 and EN 60704-1, expressing the sound power emitted by the source in dBA.
S Size - 35 mm needing to power off the other motors in the same ***Indicative value calculated with a 40 mm diameter roller. The actual value may vary depending on the specific installation.
system.
• Via radio, using Nice transmitters or the TTPRO BD
Smart palmtop programmer.
The Nice bidirectional radio protocol enables • Via a wired connection, using the TTPRO palmtop
PULL-OUT POWER CABLE ADAPTERS AND SUPPORTS
confirmation of correct reception of the command by programmer. Length 1.5 m, 3 wires in cable See the dedicated sections
the automation and the possibility of checking the in the Screen catalogue
position of the indoor blind. Acoustic and visual comfort
PHASE
CA0274A00 NEUTRAL
As it also supports the Nice mesh network function, Electronically controlled Soft Start and Soft Stop EARTH
the motor can route the radio command, thus functions allow different acceleration and deceleration
extending the radio range of the system. levels to be set in the sections near the limit switches.
CA0275A00
Minimum vibrations and silent operation for Facilitated programming thanks to the two- DIMENSIONS
maximum acoustic comfort. Noise 35 dBA. colour diagnostic LED.
Perfect alignment between the blinds, even with Energy saving
CA0276A00
multiple installations: constant motor rotation speed L
Low consumption both during motor operation and in
ERA INN 11 1 ,2
Ø1
in all load conditions and the possibility of setting the 24
standby (<0.5 W). Ø3
3
duration of up and down movements.
ACTION
CA0277A00
Ø35,2
Possibility of activating the obstacle detection Extended operation without the risk of
29
4
Ø3
CA0278A00
10
8
L
BiDi Yubii 24V Code Description Pcs./pack Certificates
TECHNICAL SPECIFICATION
Code E EDGE SI 332 DC BD E EDGE SI 620 DC BD E EDGE SI 1012 DC BD
Pushbuttons for precise and quick
limit switch adjustment ELECTRICAL SPECIFICATIONS
Antenna cable Power supply (VDC) 24
Connectors for dry contact Absorption (A) 1.5 2 1.6
input
Power (W) 36 50 40
Power consumption in standby (W) <0.5
PERFORMANCE
Torque (Nm) 3 6 10
Rated speed (rpm) 32 20 12
Maximum speed (rpm)* 48 32 20
Minimum speed (rpm) 16 10 5
Noise (dBA)** 35
Number of turns before the stop <150
Continuous operating time (min) 10 6
Lifted weight (kg)*** 12 22 34
DIMENSIONAL DATA
Length (L) (mm) 472
Cable length (m) 1.5
Tubular motor with electronic limit
Adjustable up and down speed. Weight of motor (kg) 1.1
switch, practical dry contact input Operating temperature (°C Min/Max) 0 - 60
and built-in bidirectional radio Compatible with commercially available dryCA0274A00
contact Pack dimensions (mm) 595x100x100
systems.
receiver. Protection class IP30.
*If the set speed is higher than the rated speed, motor torque is automatically reduced by 50%.
Simple installation **Noise levels have been measured in accordance with EN ISO 3745, EN ISO 3746 and EN 60704-1, expressing the sound power emitted by the source in dBA.
CA0275A00
S Size - 35 mm Each motor can be programmed individually, without ***Indicative value calculated with a 40 mm diameter roller. The actual value may vary depending on the specific installation.
needing to power off the other motors in the same
system.
Smart • Via radio, using Nice transmitters or the TTPRO BD
The Nice bidirectional radio protocol enables palmtop programmer.
CA0276A00 PULL-OUT POWER CABLE ADAPTERS AND SUPPORTS
confirmation of correct reception of the command by • Via a wired connection, using the TTPRO palmtop Length 1.5 m, 2 wires in cable See the dedicated sections in the
the automation and the possibility of checking the programmer. Screen catalogue
position of the indoor blind. CA0277A00 POSITIVE
NEGATIVE
As it also supports the Nice mesh network function, Acoustic and visual comfort
the motor can route the radio command, thus Electronically controlled Soft Start and Soft Stop
extending the radio range of the system. functions allow different acceleration and deceleration
CA0278A00
levels to be set in the sections near the limit switches.
Minimum vibrations and silent operation for DIMENSIONS
maximum acoustic comfort. Noise 35 dBA. Facilitated programming thanks to the two-
colour diagnostic LED.
Perfect alignment between the blinds, even with
multiple installations: constant motor rotation speed L
Energy saving
ERA INN 11 1 ,2
Ø1
in all load conditions and the possibility of setting the 24
Low consumption both during motor operation and in Ø3
3
duration of up and down movements.
ACTION
standby (<0.5 W).
Ø35,2
29
4
Ø3
Thanks to its compact dimensions, the motor can 10
8
be installed in even the smallest of spaces.
L
BiDi Yubii 100-240 Vac Code Description Pcs./pack Certificates
For indoor blinds, with built-in E EDGE MI 1020 AC BD Electronic limit switch, dry contact and built-in radio receiver.
100-240 VAC, 10 Nm, 20 rpm
1
bidirectional radio receiver NB: When ordering, please specify the certification required.
TECHNICAL SPECIFICATION
Pushbuttons for precise
Antenna cable and quick limit switch adjustment Code E EDGE MI 332 AC BD E EDGE MI 632 AC BD E EDGE MI 1020 AC BD
ELECTRICAL SPECIFICATIONS
Connectors for dry contact input Power supply (VAC/Hz) 100-240 / 50-60
Absorption (A) 0.8 0.95 1.1
Power (W) 45 70
Power consumption in standby (W) <0.5
PERFORMANCE
Torque (Nm) 3 6 10
Rated speed (rpm) 32 20
Maximum speed (rpm)* 48 32
Minimum speed (rpm) 16 10
Noise (dBA)** 33
Number of turns before the stop <150
Continuous operating time (min) 10 6
Lifted weight (kg)*** 10 18 29
DIMENSIONAL DATA
Length (L) (mm) 759
Cable length (m) 1.5
Tubular motor with electronic limit Possibility of activating the obstacle detection
function during both opening and closing. Weight of motor (kg) 2 2.1
switch, practical dry contact input Operating temperature (°C Min/Max) 0 - 60
and built-in bidirectional radio Adjustable up and down speed. Pack dimensions (mm) 795x100x100
receiver. Compatible with commercially available dry contact Protection class IP30.
*If the set speed is higher than the rated speed, motor torque is automatically reduced by 50%.
systems. **Noise levels have been measured in accordance with EN ISO 3745, EN ISO 3746 and EN 60704-1, expressing the sound power emitted by the source in dBA.
M size - 45 mm ***Indicative value calculated with a 50 mm diameter roller. The actual value may vary depending on the specific installation.
Simple installation
Each motor can be programmed individually, without
Smart needing to power off the other motors in the same
The Nice bidirectional radio protocol enables system.
PULL-OUT POWER CABLE ADAPTERS AND SUPPORTS
confirmation of correct reception of the command by • Via radio, using Nice transmitters or the TTPRO BD Length 1.5 m, 3 wires in cable See the dedicated sections in the
the automation and the possibility of checking the palmtop programmer. Screen catalogue
position of the indoor blind. • Via a wired connection, using the TTPROCA0274A00
palmtop
PHASE
As it also supports the Nice mesh network function, NEUTRAL
programmer. EARTH
the motor can route the radio command, thus
extending the radio range of the system. Acoustic and visual comfort
CA0275A00
Electronically controlled Soft Start and Soft Stop
Minimum vibrations and silent operation for functions allow different acceleration and deceleration DIMENSIONS
maximum acoustic comfort. levels to be set in the sections near the limit switches.
Noise 33 dBA.
CA0276A00
Facilitated programming thanks to the two-
Perfect alignment between the blinds, even with colour diagnostic LED. L
ERA INN
2
multiple installations: constant motor rotation speed 11 2
3,
32 3
Ø1
Ø
in all load conditions and the possibility of setting the
Low consumption ACTION
Energy saving CA0277A00
duration of up and down movements. both during motor operation and in
Ø45
Ø30
MEDIUM
3,5
48
standby (<0.5 W).
CA0278A00
58
Extended operation without the risk of
Ø
overheating. 17
BiDi Yubii 24V Code Description Pcs./pack Certificates
For indoor blinds, with built-in E EDGE MI 1020 DC BD Electronic limit switch, dry contact and built-in radio receiver.
24 VDC, 10 Nm, 20 rpm
1
bidirectional radio receiver NB: When ordering, please specify the certification required.
TECHNICAL SPECIFICATION
Pushbuttons for precise
Antenna cable and quick limit switch adjustment Code E EDGE MI 332 DC BD E EDGE MI 632 DC BD E EDGE MI 1020 DC BD
ELECTRICAL SPECIFICATIONS
Connectors for dry contact input Power supply (VDC) 24
Absorption (A) 1.5 3
Power (W) 36 70
Power consumption in standby (W) <0.5
PERFORMANCE
Torque (Nm) 3 6 10
Rated speed (rpm) 32 20
Maximum speed (rpm)* 48 32
Minimum speed (rpm) 16 10
Noise (dBA)** 33
Number of turns before the stop <150
Continuous operating time (min) 10 6
Lifted weight (kg)*** 10 18 29
DIMENSIONAL DATA
Length (L) (mm) 486
Cable length (m) 1.5
Tubular motor with electronic limit be installed in even the smallest of spaces.
Weight of motor (kg) 1.5 1.6
switch, practical dry contact input Adjustable up and down speed. Operating temperature (°C Min/Max) 0 - 60
and built-in bidirectional radio CA0274A00 Pack dimensions (mm) 595x100x100
Compatible with commercially available dry contact
receiver. systems. Protection class IP30.
*If the set speed is higher than the rated speed, motor torque is automatically reduced by 50%.
CA0275A00 **Noise levels have been measured in accordance with EN ISO 3745, EN ISO 3746 and EN 60704-1, expressing the sound power emitted by the source in dBA.
M size - 45 mm Simple installation ***Indicative value calculated with a 50 mm diameter roller. The actual value may vary depending on the specific installation.
Each motor can be programmed individually, without
needing to power off the other motors in the same
Smart system.
The Nice bidirectional radio protocol enables CA0276A00
• Via radio, using Nice transmitters or the TTPRO BD
PULL-OUT POWER CABLE ADAPTERS AND SUPPORTS
confirmation of correct reception of the command by palmtop programmer. Length 1.5 m, 2 wires in cable See the dedicated sections in the
the automation and the possibility of checking the • Via a wired connection, using the TTPRO palmtop Screen catalogue
position of the indoor blind. programmer. CA0277A00 POSITIVE
NEGATIVE
As it also supports the Nice mesh network function,
the motor can route the radio command, thus Acoustic and visual comfort
extending the radio range of the system. Electronically controlled Soft Start and Soft Stop
CA0278A00
functions allow different acceleration and deceleration
Minimum vibrations and silent operation for levels to be set in the sections near the limit switches. DIMENSIONS
maximum acoustic comfort.
Noise 33 dBA. Facilitated programming thanks to the two-
colour diagnostic LED.
Perfect alignment between the blinds, even with L
ERA INN
2
multiple installations: constant motor rotation speed 11 2
3,
Energy saving 32 3
Ø1
Ø
in all load conditions and the possibility of setting the
duration of up and down movements. ACTION
Low consumption both during motor operation and in
standby (<0.5 W).
Ø45
Ø30
MEDIUM
3,5
48
Possibility of activating the obstacle detection Extended operation without the risk of
function during both opening and closing.
58
overheating.
Ø
Thanks to its compact dimensions, the motor can 17
Code Description Certificates
DMBD GW
DMBD GW DIN module for the radio control of devices connected to the Nice modular
system
557.23110 Antenna cable for DMBD radio module. Length 1 m
Programming button
90,4
90,4
35
35
93
35
93
35
For the DMBD GW module to function correctly, it GW module, avoiding shielding and interference.
must be connected to a modular system consisting
of DMLPS and DMBPD power modules and at least
one DMAM, DMDCM or DMBM module to transmit
the commands received from the radio connectivity
module by wire to each of the connected motors.
DMAM
DMAM
DMDCM
DMDCM
DMWF
DMWF
DMBD
DMBD
DMKNX
DMKNX
DMBM
DMBM
DMBPD
DMBPD
DMLPS - 2415
DMLPS - 2430
DMLPS - 2415
DMLPS - 2430
Code Description
TTPRO BD
TTPRO BD Palmtop programmer for Nice tubular motors with TTBUS or dry contact technology
B1.2V2.4315 Pair of rechargeable batteries for TTPRO
No access to the automation is required: Simple cancellation of the memory and resetting to
You can control and programme automations with default configurations.
Nice bidirectional radio without needing physical
"Macro" function to copy the settings to a number of
access to the motor itself. Installation is completely
motors.
wireless.
Firmware update via PC and practical USB cable for
Simple, direct programming, including by recharging the TTPRO BD.
wireless, of:
• electronic limit switches; Radio test
• intermediate heights; Possibility of checking for any ambient radio
interference.
We make even the
smallest of gestures
extraordinary.
Nice,
a world without barriers.
Automation and control systems for gates, garage
doors, blinds, awnings and rolling shutters and alarm
systems for all types of space, from private homes to
large public buildings.
www.niceforyou.com
Nice SpA
Oderzo, TV, Italy
The information shown in this publication is purely indicative. Nice reserves the right to make any modifi cations to the products as it sees fit. Product Design Roberto Gherlenda