Professional Documents
Culture Documents
Continental Disc Corporation Rupture Disc Selection Guide
Continental Disc Corporation Rupture Disc Selection Guide
2 3
TYPE OF DISC
Fig. A Fig. C
Process Side
Process Side
Fig. B
Reverse Acting rupture discs are
oriented in a system with the process
media pressure against the convex side
of the disc (Figure C), placing the rupture
disc in compression. As the burst pressure
rating of the disc is reached, the
compression loading on the rupture disc
causes it to reverse, snapping through the
neutral position and causing it to open by a
predetermined scoring pattern or knife
Process Side
blade penetration.
A reverse acting rupture disc provides
Tension Type rupture discs are some advantages, as compared to tension
oriented in a system with the process type rupture discs, which may warrant
media pressure against the concave consideration when selecting a rupture disc.
side of the rupture disc (Figure A, 30° Seat; These advantages include:
Figure B, Flat Seat). As the process • Zero manufacturing range allowing
pressure increases beyond the allowable the rupture disc to operate to 90%
operating pressure, the rupture disc starts of its stamped burst pressure
to grow. This growth will continue as
• Full vacuum capabilities without the
the pressure increases, until the tensile
need of an additional support member
strength of the material is reached and
rupture occurs. • Longer service life under cyclic or
pulsating conditions
• Constructed using thicker materials
providing greater resistance to
corrosion
4
TENSION TYPE DISC
A Standard Rupture Disc is a solid metal, The Composite Rupture Disc is designed for
differential pressure relief device with an systems requiring a lower burst pressure than
instantaneous, full-opening, non-reclosing design. offered in Standard discs. C.D.C.’s patented
seven-hole center pattern is designed for
SPECIFICATIONS non-fragmentation when used with a Teflon seal.
Sizes: 1/4" - 30"
(6,0mm - 750mm) diameter SPECIFICATIONS
MICRO X® Cross Scored Rupture Disc Composite Flat Seat Rupture Disc
The MICRO X Rupture Disc is a cross-scored The Composite Flat Seat Rupture Disc is
flat seat tension type rupture disc. It is designed designed for systems requiring a lower burst
for non-fragmentation with a four-petal opening. pressure than offered in a MICRO X Rupture Disc.
C.D.C.’s seven-hole center pattern provides a
SPECIFICATIONS: non-fragmenting design when used with a
Teflon seal.
Sizes: 1" - 36"
(25mm - 900mm) diameter SPECIFICATIONS:
Operating conditions: Sizes: 11 / 16" - 36"
Pressure: Up to 80% of rated burst pressure (17,5mm - 900mm) diameter
Temperature: To 1000°F (538°C)
Depending on material
Operating conditions:
Pressure: Up to 80% of rated burst pressure
Burst pressure: 15 to 3600 psig @ 72°F Temperature: To 1000°F (538°C)
(1,03 to 248 barg @ 22°C) Depending on material
Depending on size
Burst pressure: 2 to 1440 psig @ 72°F
Service: Liquid or gas, static, pulsating or (0,138 to 99,3 barg @ 22°C)
cyclic conditions; may be used under a Depending on size
pressure relief valve
Service: Liquid or gas, static, pulsating or
Material: Nickel, Monel, Inconel, Tantalum, cyclic conditions; may be used under
Hastelloy C, or 316SS; pressure relief valves
other materials available
Material:
Tagging: Three-dimensional stainless steel Top Section: 316SS, Nickel, Inconel, Monel,
flow tag attached to all sizes Tantalum, or Hastelloy C
Seat type: Flat seat Seal: Teflon or metal
Holder: UNISERT®, QUICK-CHANGE or Other materials available
CLEAN-SWEEP® holder Tagging: Three-dimensional stainless steel
Alarm system: B.D.I. Alarm System compatible flow tag attached to 1" (25mm)
and above
Options:
Rupture Disc: Liners, coatings, vacuum support Seat type: Flat seat
(vacuum support not required in 1"- 4" {25mm- Holders: UNISERT, Tite-Seal, Screw Type,
100mm} size) QUICK-CHANGE, Sanitary or
Holder: J-Hook, coating, special gasket CLEAN-SWEEP holder
surface finish, gauge tap, Alarm system: B.D.I. Alarm System compatible
tantalum lining (UNISERT)
Options:
Rupture Disc: Liners, protective rings,
gaskets, vacuum support
Holder: J-Hook, coating, special gasket
surface finish, gauge tap,
tantalum lining (UNISERT)
For additional information:
UNISERT Assembly bulletin #2-2203-2
6
TENSION TYPE DISC
The ENVIRO-SEAL Rupture Disc is a flat The Tite-Seal Rupture Disc Assembly is an
composite rupture disc, designed to provide economical “throwaway” sealed unit available with
economic isolation for low pressure atmospheric 1/4", 3/8" or 1/2" MPT inlet connections and outlet
storage vessels or to isolate the downstream configurations with an MPT connection, muffled
side of a pressure relief valve. or free vent.
ENVIRO-SEAL Rupture Discs are available in
SPECIFICATIONS:
three designs:
• Type I: Burst in one direction only Disc type:
• Type II & III: Burst in either direction, positive or 1/2" Standard Preformed Rupture Disc:
vacuum, at the same burst pressure Operating conditions:
Pressure: Up to 70% of rated burst pressure
SPECIFICATIONS:
Temperature: To 400°F (204°C)
Sizes: 2"- 36" Burst pressure: 65 to 3000 psig @ 72°F
(50mm - 900mm) diameter (4,48 to 207 barg @ 22°C)
Operating conditions: Material: Silver, Aluminum, Monel, Nickel,
Pressure: Up to 50% of rated burst pressure Inconel, Hastelloy C®* or 316SS
Temperature: To 400°F (204°C) Options: Vacuum support, Teflon coating or
Burst pressure: 1 to 59 psig @ 72°F gasket
(0,069 to 4,07 barg @ 22°C) 11/16" Composite Rupture Disc:
Depending on size
Operating conditions:
Service: Gas or liquid
Pressure: Up to 80% of rated burst pressure
Material: Temperature: To 400°F (204°C)
Top section(s): 316SS, Nickel, Inconel,
Burst pressure: 30 to 1000 psig @ 72°F
Monel, Tantalum, or Hastelloy C;
(2,07 to 68,9 barg @ 22°C)
other materials available
Seal(s): Teflon or Polyethylene Material:
(at the discretion of C.D.C.) Top Section: 316SS, Monel, Inconel,
Gaskets: Non-asbestos both sides Nickel or Hastelloy C;
other materials available
Tagging: Three-dimensional stainless steel
flow tag attached Seal: Teflon or Silver
Alarm system: B.D.I. Alarm System compatible Vacuum support: 316SS or Hastelloy C
7
TENSION TYPE
GRAFSERT Rupture Discs are The ICON Rupture Disc is a The Tanksert Rupture Disc is
machined from a monolithic piece of cross-scored, non-fragmenting design designed for use on railroad tank cars,
graphite and impregnated with phenolic. solid metal rupture disc specifically over the road tank trucks and other
Graphite discs are corrosive resistant to designed to protect transportation transportable vessels. It is designed
many chemicals. vessels like intermodal tank containers to fit both threaded and bolted type
(common in Europe and Asia), Safety Vent Assemblies.
SPECIFICATIONS railroad tank cars, tank trucks, and
other vessels that transport liquids Two styles are available:
Sizes: 1/2" - 24" or gas products. 1. Tanksert Rupture Disc with Bee Screen
(13mm - 600mm) diameter
is used for applications that require
Operating conditions: SPECIFICATIONS protection against bees, insects or
Pressure: Up to 80% of rated burst other airborne particles from entering
Sizes: 65mm and 80mm
pressure. 90% available in the tank after a rupture disc opening
specific static conditions; Operating conditions: has occurred.
consult the factory for details Pressure: Up to 80% of rated burst
2. Tanksert Rupture Disc without bee
Temperature: To 700°F (371°C) pressure; full vacuum
screen.
Burst pressure: 0.25 to 720 psig @ 72°F Standard Burst pressures:
(0,017 to 49,6 barg @ 22°C) 3,67; 4,10 or 4,84 barg at 20°C; SPECIFICATIONS
Depending on size other pressures available
Size: 2" to fit Safety Vent Assembly
Service: Gas or liquid Service: Liquid or gas
Operating pressure:
Material: Graphite impregnated Material: Nickel disc standard, with Up to 80% of rated burst pressure
with phenolic 316SS inlet / outlet rings;
other materials available Standard Burst pressures:
Seat configuration: Flat seat Stocked and available for immediate
Option: Teflon liner shipment in:
Holder: Installs directly between 150# or
300# ANSI class flanges and Seat type: Flat seat 25 to 30 . . . .psig @ 72°F
equivalent classes DIN or JIS 40 to 45 . . . . " "
Holders: Designed to mount directly 55 to 60 . . . . " "
flanges (separate holder not to tank flanges
required) 70 to 75 . . . . " "
Tagging: Stainless steel tag attached 95 to 100 . . . " "
Tagging: Stainless steel tag attached 155 to 165 . . " "
Alarm system: B.D.I. Alarm System Material: Stainless steel rupture disc
compatible components with Teflon seal;
Options: Coatings, liners, armor ring, Bee screen of #14 or #20
vacuum support, gaskets, mesh stainless steel
high temperature assembly
8
REVERSE ACTING
ULTRX Rupture Disc MINTRX Rupture Disc STAR X Rupture Disc LOTRX Rupture Disc
Sizes: 1" - 12" Sizes: 1" - 8" Sizes: 1" - 6" Sizes: 1" - 8"
(25mm - 300mm) diameter (25mm - 200mm) diameter (25mm - 150mm) diameter (25mm - 200mm) diameter
Burst pressure: Burst pressure: Burst pressure: Burst pressure:
15 to 1000 psig @ 72°F 20 to 139 psig @ 72°F 13 to 140 psig @ 72°F 1.5 to 39.9 psig @ 72°F
(1,03 to 68,9 barg @ 22°C) (1,38 to 9,58 barg @ 22°C) (0,896 to 9,65 barg @ 22°C) (0,103 to 2,75 barg @ 22°C)
• ULTRX operates in GAS, VAPOR or FULL LIQUID Sizes: Shown above; consult the factory for
service conditions. larger sizes
• MINTRX, STAR X, and LOTRX operate in Operating pressure:
gaseous service conditions – consult the factory Pressure: Up to 90% of rated burst pressure
for liquid service applications. (for burst pressures 40 psig and above)
Temperature: To 1000°F (538°C)
• Zero manufacturing range as standard, allowing the
disc to be operated to 90% of its rated burst pressure Service: Static, pulsating or cyclic conditions;
(for burst pressures 40 psig and above. Below 40 excellent for use under pressure
psig, operation is to 90% of the lower portion of the relief valve
burst tolerance range). Material: Hastelloy C, Inconel, Nickel, Monel,
• Safety ratio of 1.5 or less. In the event of rupture disc or 316SS; other materials available
damage, burst will occur within 1.5 times the rated Tagging: Three dimensional stainless steel
burst pressure (LOTRX safety ratio: 1.0). flow tag attached to all sizes
• Inherent with most reverse acting type of rupture Manufacturing range: ZERO is standard;
discs on the market, these discs will operate in -5% or -10% optional
pressure-to-vacuum cycling applications without an
additional vacuum support component, for burst Seat configuration: Flat seat
pressures 5 psig (0,34 barg) and above. Holder: ULTRX, MINTRX, STAR X and LOTRX
• Encapsulating rings on ULTRX, MINTRX, and holders, each with unique alignment pin
LOTRX provide perfect alignment and pattern and J-Hook as standard, or
minimize seal load sensitivity. Quick-Change
• Three-dimensional stainless steel flow tag provides Alarm system: B.D.I. Alarm System compatible
immediate verification of proper installation. The tag (consult factory for B.D.I. Alarm System with
is stainless steel for resistance to corrosion. LOTRX Rupture Disc)
• Designed for non-fragmentation. Options:
• Unique holder utilizes disc alignment pins to aid Rupture Disc: Process side - liner
proper disc orientation in holder, and a J-Hook to aid Outlet side - protective cover
proper orientation relative to flow direction between Holder: Gauge tap, Teflon coating,
companion flanges. special gasket surface finish,
tantalum lining
• Thicker disc material (than tension type rupture disc
of similar burst pressure) adds corrosion resistance.
The RCS Rupture Disc is a reverse acting, cross- The SANITRX Rupture Disc is a reverse acting,
scored, solid metal rupture disc, providing reliable solid metal rupture disc with Continental’s patented
pressure relief protection, easy installation, and retrofit to “failure initiating indents,” designed to provide
your pre-existing piping arrangement. overpressure protection in sanitary environments. Also
available, the SANITRX LP™ Rupture Disc, with lower
SPECIFICATIONS: pressures and a much lower KR factor, available in 1"- 3"
(25-80mm) size.
Sizes: 1" - 32"
(25mm - 800mm) diameter SPECIFICATIONS:
Operating conditions:
Sizes: 1-1/2" - 4"
Pressure: Up to 90% of rated burst pressure
(40mm - 100mm) diameter
Temperature: To 1000°F (538°C)
Operating conditions:
Burst pressure: 20 to 1000 psig @ 72°F Pressure: Up to 90% of rated burst pressure
(1,38 to 68,9 barg @ 22°C)
Temperature: Rated up to 450°F (232°C),
Depending on size
Depending on gasket material
Service: Gaseous, static, pulsating or cyclic conditions;
Burst pressure: 14 to 500 psig @ 72°F
may be used under pressure relief valve
(0,965 to 34,5 barg @ 22°C)
Material: Nickel, 316SS, Monel, Inconel and Hastelloy C Depending on size
Tagging: Three-dimensional stainless steel flow tag Service: Gaseous, static, pulsating or cyclic conditions;
attached to all sizes may be used under pressure relief valve
Seat configuration: Flat seat Material:
Disc: Nickel, Monel, 316SS, Inconel, Hastelloy C,
Holder: RCS Insert Holder
Aluminum and Tantalum
Alarm system: B.D.I. Alarm System compatible Gasket: Viton, Buna-N, Silicone, EPDM, PTFE Teflon,
Options: and Platinum Cured Silicone
Rupture Disc: Process side - Teflon liner Tagging: Three-dimensional stainless steel flow tag
Outlet side - protective cover attached to all sizes
Holder: J-Hook, coatings, special gasket surface
Seat configuration: Flat seat
finish
Holder: Designed to install directly between sanitary tube
O.D. connections using a sanitary clamping device
Alarm system: B.D.I. Alarm System compatible
ZAP® Reverse Acting Rupture Disc KBA Reverse Acting Rupture Disc
The ZAP Reverse Acting Rupture Disc design The KBA Reverse Acting Rupture Disc utilizes
utilizes replaceable knife blades in the holder outlet permanently attached knife blades in the holder outlet
to cut open the rupture disc as reversal occurs. to cut open the disc as reversal occurs.
Proven features include: Proven features include:
• Zero manufacturing range • Zero manufacturing range
• Exceptional cyclic or pulsating service life compared to • Exceptional cyclic or pulsating service life compared
tension type rupture discs to tension type rupture discs
• May be operated under full vacuum or backpressure • May operate under full vacuum or backpressure
to 110% of the rated burst pressure without an additional to 110% of the rated burst pressure without an additional
vacuum support compared to tension type rupture disc vacuum support compared to tension type rupture disc
• Encapsulating rings provide perfect alignment and • Thicker disc material adds corrosion resistance
minimize seal load sensitivity • Permanently attached knife blades
• Replaceable knife blades for easy, quick replacement
SPECIFICATIONS:
• Thicker disc material adds corrosion resistance
Sizes: 1" - 32"
SPECIFICATIONS: (25mm - 800mm) diameter
Insert Style
Insert Style
Sanitary Style
Sanitary Style
The CAL-VAC Rupture Disc Assembly is a highly The POS-A-SET Rupture Disc Assembly is a highly
accurate pressure relief device for protecting vessels accurate pressure relief device for protecting vessels and
and equipment against damaging vacuum conditions. equipment against damaging positive pressure conditions.
Proven features include: Proven features include:
• Designed to open on vacuum within a 6" water column • Designed to open on positive pressure within a
spread 6" water column spread
• Pressure setting starting at 1" water column • Positive pressure setting starting at 1" water column
• Can be operated to within 1" water column or 90%, • Can be operated to within 1" water column or 90%,
dependent upon rating dependent upon rating
• Dual directional pressure protection (positive or negative) • Dual directional pressure protection (positive or negative)
• Designed for non-fragmentation • Designed for non-fragmentation
SPECIFICATIONS: SPECIFICATIONS:
Sizes: Insert Style 3" - 12" Sizes: Insert Style 3" - 12"
(80mm - 300mm) diameter (80mm - 300mm) diameter
Sanitary Style 3" - 10" Sanitary Style 3" - 10"
(80mm - 250mm) diameter (80mm - 250mm) diameter
Operating conditions: Operating conditions:
Vacuum Pressure: Up to 90% of minimum vacuum Positive Pressure: Up to 90% of minimum positive
pressure set point or within 1" of pressure set point or within 1" of
water column, whichever is greater water column, whichever is greater
Positive pressure: Up to 80% of rated burst Vacuum: Up to 80% of rated pressure in the
pressure vacuum direction
Temperature: To 400°F (204°C) Temperature: To 400°F (204°C)
Burst pressure: Burst pressure:
Vacuum: 6" water column spread Positive: 6" water column spread
between 1" to 30" of water column between 1" to 30" of water column
Depending on size Depending on size
Positive: 2 to 150 psig (0,138 - 10,3 barg) Vacuum: To full vacuum.
Depending on size Seat configuration: Flat seat
Seat configuration: Flat seat Holder: Sanitary, insert type or QUICK-CHANGE
Holder: Sanitary, insert type or QUICK-CHANGE Alarm system: B.D.I. Alarm System compatible
Alarm system: B.D.I. Alarm System compatible
For additional information:
CAL-VAC / POS-A-SET Rupture Disc Assemblies bulletin #4-8804-4
12
VENT PANELS
CP Series:
The CP series flat composite vent panel
is excellent for applications requiring cyclic
conditions (positive to negative
pressures), low opening pressures and the
need for stainless steel construction.
14
SPECIAL ASSEMBLIES
15
RUPTURE DISC HOLDERS
C.D.C. holders are available in a correct rupture disc orientation in the configurations, dependent upon size.
variety of types and styles to meet your holder. A J-Hook, along with flow direction Welded, threaded or flat faced inlets and
needs. The product chart, as shown on arrows on the nameplate, aids in proper outlets are available. Stainless steel flow
pages 18, 19 and 20, shows which disc assembly installation between the directional nameplates are provided.
may be used in specific holders, and the companion flanges.
holder options which are available. Screw Type Holders
3. The RHI Insert holder has a flat seat
C.D.C. offers an extensive line of configuration for use with either a
holders including: MICRO X or Composite flat seat rupture
• Insert disc. The minimal overall height of the
• Bolted assembly allows installation in tight piping
• Screw Type arrangements, and retrofit in many
• Union Type existing installations, while still providing
• CLEAN-SWEEP the benefits and features of the
• Sanitary Holders Continental flat seat rupture disc design
• QUICK-CHANGE holders (see UNISERT).
Consult your C.D.C. representative or 4. The ULTRX, MINTRX, STAR X, and
the factory for those applications needing LOTRX Insert holders are designed with
additional features or modification. either a tapered or flat raised seat on the
holder inlet. This design allows a uniform Screw Type Holders are available
Insert Holders seal load on the mating rupture disc. for pressures ranging up to 20,000 psig.
Each holder has a number of round The Screw Type holder is supplied
and /or oblong pins and the mating with 1 / 4" or 1 / 2" MPT inlet threads in
rupture disc is identically notched, combination with MPT, free or muffled
providing proper rupture disc orientation outlets. The 1 / 2" Standard and 11 / 16"
in the holder. A J-Hook and flow direction Composite Rupture Disc are used in
arrows on the nameplates aid in the these holders. Special high pressure
correct assembly orientation between designs are available.
companion flanges.
Union Holders
5. The ZAP and KBA Insert holders
have an integral mating interlock device
which correctly orients the holder inlet
Insert type rupture disc holders are flat and outlet with respect to each other. The
faced assemblies that fit between two ZAP Holder is available with either a
ANSI, DIN, JIS or BSI companion replaceable or permanently welded knife
flanges, as shown in the photograph blade assembly. The KBA Holder comes
above. Insert holders to fit other standards with permanently welded knife blades.
are available. These holders are designed
for eleven different rupture disc styles, 6. The RCS Insert holder is designed for
described in paragraphs 1 through 6 simplicity and safety of installation with
below. Common features of C.D.C.’s superior sealing capabilities. Three round
Insert Holders include: pins located in the holder inlet and
• Fit within companion flange bolts, matching holes in the RCS Rupture Disc Union Holders are available for
allowing easy installation and removal provide correct rupture disc and flow pressure ranges up to 6000 psig,
direction orientation. A tapered seat depending on disc size. All sizes are
• Preassembly clips are standard and configuration allows a uniform seal load available with threaded or welded inlets
provide means to assemble the on the rupture disc. in combination with threaded, welded or
rupture disc and holder together muffled outlets. Special unions are
before installation in piping system Full Bolted Holders available.
• Stainless steel flow direction nameplates
permanently attached to the holder Sealing Capabilities
• Stainless steel customer identification
tag permanently attached Continental’s holder designs provide
superior sealing capabilities to prevent
1. 7I Insert holders, designed for product loss or contamination. The
Standard and Composite rupture discs, tapered seat configuration of
are available in 30° light or heavy lip Continental’s UNISERT, RHI, ULTRX,
configurations, dependent upon size. MINTRX, STAR X and RCS holders
outperforms other, similar designs,
2. The UNISERT Insert holder has a flat Full Bolted Holders do not need without the need for “pretorque”
seat configuration for use with either a companion flanges. The proper seat arrangements. A pretorque-able holder is
MICRO X or Composite flat seat rupture configuration is machined directly into the available for those customers whose
disc. Holder alignment pins and matching flange. Full bolted holders are available specifications require it.
notches in the rupture disc provide in 30° light or heavy lip seat
16
RUPTURE DISC HOLDERS
CLEAN-SWEEP®
Rupture Disc Holder Sanitary Holder QUICK-CHANGE Holder
-5
(B .D
URE
STANDARD MATERIALS** COMPATIBLE HOLDERS
701
tion
OF S LATION
FOR MENDE
G
VE
RAT RST PR ING
ESS
7
icato
RIN
ifica
FULL ED TO W T
TO B OPERA D
o .5 -
ulle bove)
VAL
IT
OR
Y
E
T
T
MAX MMEND
76
RAN FACTU
REQU M SUPP
tin N
Cert
AFE
ISO
(1 in isc Ind
ANGE
OM
EEP
Y C -2
a
Burs ABLE
IEF
ED
BLE
TYPE
nd
VACU
UM
ALUM
BURST
BOLT
N-SW
HITE
REC
TARY
REL
K-CH
SEAL
ELLO
ch a
GE
EL
ILA
IR
IN
U
tD
IO
U
IL
EL
W
EL
RT
PRESSURE CONTINENTAL RUPTURE DISC TYPE FLOW
O
.
ef. B
PROCESS
S
N
E
N
MAN
ALUM
VACU
GRAP
316S
SCRE
AVA
TANT
ASM
REC
INCO
NICK
HAST
FULL
UNIO
CLEA
QUIC
MON
SANI
TITE-
AVA
INSE
ENVIRONMENT SIZE RANGE & BULLETIN No. DIRECTION YES NO
R
STANDARD 30°
Liquid or Gas
(static, cyclic or pulsating)
1/4" - 30"
6mm - 750mm
3 - 80,000 psig
0,207 - 5516 barg
70% Standard
3/4, 1/2
1/4
Yes
.. . . . . . No. 2-2201-2
. . . .. . . . . .
COMPOSITE 30°
1" - 30" 2 - 1440 psig 80% Standard Yes
Liquid or Gas
.. . . . . . ... . . . .
No. 2-2202-2
(static, cyclic or pulsating) 25mm - 750mm 0,138 - 99,3 barg 3/4, 1/2
1/4
COMPOSITE FS
.. . . . . .
Liquid or Gas 11/16" - 36" 2 - 1440 psig 80% Standard Yes
. .. . . . . . .
No. 2-2202-2
(static, cyclic or pulsating) 17,5mm - 900mm 0,138 - 99,3 barg 3/4, 1/2
1/4
MICRO X®
Liquid or Gas
. . . . . . . . . . . .
1" - 36" 15 - 3600 psig 80% Standard No* No. 2-2203-2
(static, cyclic or pulsating) 25mm - 900mm 1,03 - 248 barg -5%
-10%
ULTRX®
.. . . . .
1" - 12" 15 - 1000 psig 90% ZERO No
. . . . .
No. 3-2210-3
Liquid or Gas
25 - 300mm 1,03 - 68,9 barg -5%
(static, cyclic or pulsating)
-10%
MINTRX®
Gas – consult the factory 1" - 8" 20 - 139 psig 90% ZERO No
. . . . . . . . . . .
No. 3-2218-3
for liquid applications 25mm - 200mm 1,38 - 9,58 barg -5%
(static, cyclic or pulsating) -10%
STAR X®
Gas – consult the factory 1" - 6" 13 - 140 psig 90% ZERO No
for liquid applications
(static, cyclic or pulsating)
25mm - 150mm 0,896 - 9,65 barg -5%
-10%
.. . . . . . TB-SRX-0394
. . . . .
LOTRX®
Gas – consult the factory 1" - 8" 1.5 - 39.9 psig 90% ZERO No*
. . . . . . . . .
TB-LTRX0101
for liquid applications 25mm - 200mm 0,103 - 2,75 barg -5% (3" - 8" size)
(static, cyclic or pulsating) -10%
ZAP®
Gas
. . . . . . . . . . .
1" - 8" 15 - 1000 psig 90% ZERO No No. 3-2220-3
(static, cyclic or pulsating) 25mm - 200mm 1,03 - 68,9 barg
KBA
Gas
.. . . . . .
1" - 32" 15 - 1000 psig 90% ZERO No
(static, cyclic or pulsating) 25mm - 800mm 1,03 - 68,9 barg
No. 3-2220-3
. . . .
RCSTM
Gas 1" - 32" 20 - 1000 psig 90% ZERO No
. . . . . . . . .
No. 3-2225
(static, cyclic or pulsating) 25mm - 800mm 1,38 - 68,9 barg -5%
-10%
6 inch CAL-VAC®
3" - 12" 1 inch - 30 inch Within 1 inch NOT
. . . . . . . .. . .
Liquid or Gas water No. 4-8804-4
80mm - 300mm water W.C. of applicable
(static, cyclic or pulsating) column
column min. setting
min/ max
6 inch POS-A-SET®
Liquid or Gas 3" - 12" 1 inch - 30 inch Within 1 inch NOT
. . . . . . . .. . .
water No. 4-8804-4
(static, cyclic or pulsating) 80mm - 300mm water W.C. of column applicable
column min. setting min/ max
SANITRX®
Gas – consult the factory 1" - 4" 10 - 500 psig 90% ZERO No* No holder required.
for liquid applications
(static, cyclic or pulsating)
25mm - 100mm 0,690 - 34,5 barg -5%
-10%
.. . . . . . No. 4-8803
SANITRX LP™
TB-SNXL-0403
Installs between standard sanitary ferrules. . . .
ENVIRO-SEAL
2" - 36" 1 - 59 psig 50% Min/Max No* Downstream
Liquid or Gas
. . . . . . No holder required.
. .
No. 2-2202-2
50mm - 900mm 0,069 - 4,07 barg Bolts between standard bore companion flanges. Only
(static, cyclic or pulsating)
GRAFSERT®
Liquid or Gas
. . . .
1/2" - 24" 0.25 - 720 psig 80% Standard No* No. 2-2204-2 No holder required.
(static, cyclic or pulsating) 13mm - 600mm 0,017 - 49,6 barg Bolts between companion flanges.
*Dependent upon burst pressure. **Materials not indicated or shown may be available by special design. Contact the factory.
VENT PANELS provide instantaneous overpressure relief to
minimize structural or mechanical damage that may be caused by expanding
gases as a result of deflagration of dust, gases or mists. These panels are
available in a wide variety of styles, configurations and materials. Refer to
page 13 for further information.
For additional information, please check the ULTRA-LOW PRESSURE Rupture Discs / Holders
appropriate product categories and fill in your
address. Thank you.
G CAL-VAC rupture disc assembly
G POS-A-SET rupture disc assembly
TENSION TYPE Rupture Discs VENT PANELS
CORPORATE HEADQUARTERS
Continental Disc Corporation
3160 W. Heartland Drive
Liberty, Missouri 64068-3385 USA
ASME Code Symbol Stamp
Available When Specified
Phone: (816) 792-1500
FAX: (816) 792-2277 / 5447
E-Mail: pressure@contdisc.com
Pressure Equipment Directive China Manufacture License Website: www.contdisc.com
Available When Specified Available When Specified
A Siegel-Robert Company
Continental Disc Corporation reserves the right to alter the information in this publication without notice.
Reproduction without written permission prohibited. © 1997-2005 Continental Disc Corporation Printed in U.S.A.
11060001CD
STAMP
ATTENTION: Marketing
ALL GAS / LIQUID HANDLING SYSTEMS, I.E. ...CHEMICAL • PETROCHEMICAL • PETROLEUM REFINING
FOOD PROCESSING • BREWING • LIQUID STORAGE • POWDER BULK STORAGE • RAILROAD TANK CARS
INTERMODAL TANK CONTAINER • PULP & PAPER PROCESSING • COMMERCIAL AVIATION
AEROSPACE • PHARMACEUTICAL • BIO-TECHNOLOGY • O.E.M. • DUST COLLECTION SYSTEMS