Professional Documents
Culture Documents
Description: Steering Pad Switch Circuit
Description: Steering Pad Switch Circuit
Title: AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: Steering Pad Switch Circuit; 2014 2016 MY IS200T IS250
IS300 IS350 [04/2013 ]
Steering Pad Switch Circuit
DESCRIPTION
This circuit sends an operation signal from the steering pad switch assembly to the radio receiver assembly.
If there is an open in the circuit, the audio and visual system cannot be operated using the steering pad switch
assembly.
If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.
Therefore, the radio receiver assembly cannot be operated using the steering pad switch assembly, also the radio
receiver assembly itself will not function.
WIRING DIAGRAM
https://techinfo.toyota.com/t3Portal/resources/jsp/siviewer/index.jsp?dir=rm/RM30G0U&locale=en&User=false&publicationNumber=RM30G0U&objType=toc/… 1/6
3/6/2017 AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: Steering Pad Switch Circuit; 2014 2016 MY IS200T IS250 IS300 IS350 [04/2013 ]
CAUTION / NOTICE / HINT
NOTICE:
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as
airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for
Supplemental Restraint System.
Click here
PROCEDURE
1. CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
(a) Disconnect the K72 radio receiver assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
https://techinfo.toyota.com/t3Portal/resources/jsp/siviewer/index.jsp?dir=rm/RM30G0U&locale=en&User=false&publicationNumber=RM30G0U&objType=toc/… 2/6
3/6/2017 AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: Steering Pad Switch Circuit; 2014 2016 MY IS200T IS250 IS300 IS350 [04/2013 ]
No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume switch pushed 2955 to 3265 Ω
No switch pushed 95 to 105 kΩ
MODE switch pushed Below 2.5 Ω
Off hook switch pushed 950 to 1050 Ω
Voice switch pushed 2955 to 3265 Ω
PROCEED TO NEXT SUSPECTED AREA SHOWN IN
OK PROBLEM SYMPTOMS TABLE
NG
2. INSPECT STEERING PAD SWITCH ASSEMBLY
(a) Remove the steering pad switch assembly.
Click here
(b) Measure the resistance according to the value(s) in the table below.
https://techinfo.toyota.com/t3Portal/resources/jsp/siviewer/index.jsp?dir=rm/RM30G0U&locale=en&User=false&publicationNumber=RM30G0U&objType=toc/… 3/6
3/6/2017 AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: Steering Pad Switch Circuit; 2014 2016 MY IS200T IS250 IS300 IS350 [04/2013 ]
Component without harness
*a connected *b Volume+
(Steering Pad Switch Assembly)
*c Volume *d MODE
*e Seek+ *f Seek
*g Off hook *h On hook
*i Voice
Standard Resistance:
No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume switch pushed 2955 to 3265 Ω
No switch pushed 95 to 105 kΩ
MODE switch pushed Below 2.5 Ω
Off hook switch pushed 950 to 1050 Ω
Voice switch pushed 2955 to 3265 Ω
https://techinfo.toyota.com/t3Portal/resources/jsp/siviewer/index.jsp?dir=rm/RM30G0U&locale=en&User=false&publicationNumber=RM30G0U&objType=toc/… 4/6
3/6/2017 AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: Steering Pad Switch Circuit; 2014 2016 MY IS200T IS250 IS300 IS350 [04/2013 ]
NG REPLACE STEERING PAD SWITCH ASSEMBLY
OK
3. INSPECT SPIRAL CABLE WITH SENSOR SUBASSEMBLY
(a) Remove the spiral cable with sensor subassembly.
Click here
(b) Measure the resistance according to the value(s)
in the table below.
Standard Resistance:
Center
2.5 rotations to
z48 (EAU) K263
the left 3 Ω or less
(EAU)
2.5 rotations to
the right
Center
2.5 rotations to
z411 (AU1) K26
the left 3 Ω or less
6 (AU1)
2.5 rotations to
the right
Center
2.5 rotations to
z410 (AU2) K26
the left 3 Ω or less
5 (AU2)
2.5 rotations to Component without harness connected
*a
the right (Spiral Cable with Sensor Subassembly)
*b Steering Pad Switch Assembly Side
*c Vehicle Side
(c) After setting the spiral cable with sensor subassembly to the center position, rotate the spiral cable
with sensor subassembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub
assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table
below.
https://techinfo.toyota.com/t3Portal/resources/jsp/siviewer/index.jsp?dir=rm/RM30G0U&locale=en&User=false&publicationNumber=RM30G0U&objType=toc/… 5/6
3/6/2017 AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: Steering Pad Switch Circuit; 2014 2016 MY IS200T IS250 IS300 IS350 [04/2013 ]
Standard Resistance:
NOTICE:
Press and hold the lock located in the center of the spiral cable with sensor subassembly to rotate the spiral
cable with sensor subassembly.
The spiral cable with sensor subassembly is an important part of the SRS airbag system. Incorrect removal or
installation of the spiral cable with sensor subassembly may prevent the airbag from deploying.
As the spiral cable with sensor subassembly may break, do not rotate the spiral cable with sensor subassembly
more than the specified amount.
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK (RADIO RECEIVER ASSEMBLY SPIRAL CABLE WITH
SENSOR SUBASSEMBLY)
REPLACE SPIRAL CABLE WITH SENSOR SUB
NG ASSEMBLY
https://techinfo.toyota.com/t3Portal/resources/jsp/siviewer/index.jsp?dir=rm/RM30G0U&locale=en&User=false&publicationNumber=RM30G0U&objType=toc/… 6/6