Professional Documents
Culture Documents
Dampers & Louvers Full Submittal PDF
Dampers & Louvers Full Submittal PDF
Dampers & Louvers Full Submittal PDF
ABU RKHAYA
DAMPERS TECHNICAL SUBMITTAL
www.airmasteremirates.com
19.0 FIRE
DAMPER
19.0 index
INDEX
SECTION TOPIC PAGE
19.1 Introduction 3
2015 Edition.
www.airmasteremirates.com 02 Copyright reserved. Specifications subject to change without notice.
19.1
FIRE
DAMPER
INTRODUCTION
2015 Edition.
Copyright reserved. Specifications subject to change without notice.
03 www.airmasteremirates.com
19.1
FIRE
DAMPER
The most prominent testing laboratories for The open/close position can be monitored by
evaluating fire resistive materials and assemblies is introducing a limit switch or Auxiliary switch in the
the Underwriters Laboratory (UL), U.S.A. All damper which communicates the open/close status
Airmaster Fire dampers are tested and certified by to the BMS or a standalone control panel. As a
UL. result, further actions could be programmed like
switching on smoke extract fans or switching off all
Airmaster fire dampers are developed with the HVAC units or informing Fire department and so on.
intention of maximizing the occupant's safety. There
are two basic types of damper operations: a) Curtain UL Testing:
type b) Multiple blade type. Though construction of Airmaster has taken great efforts in developing fire
both dampers are different, the purpose is the same – dampers and getting it certified from UL after passing
to interrupt airflow in order to restrict the passage of their stringent testing procedures successfully. Our
fire & smoke. dampers have withstood the demanding test
requirements of UL 555 and UL 555S standards.
Curtain type: The blades are folded and held under Both these standards call of series of tests like:
spring tension using a bi-metal fusible link. Heat of
165oF (74oC) inside the duct is sufficient for fusible
link to melt and break, thus allowing blades to shut
like a curtain under the force of the springs attached.
The fire damper acts as a barrier between fire and
non-fire zones thus containing the fire in the
compartment from which it originated. This gives
sufficient time for occupants to escape and move into
safety.
2015 Edition.
www.airmasteremirates.com 04 Copyright reserved. Specifications subject to change without notice.
19.1
FIRE
DAMPER
UL listed products are finally dispatched after UL Maintenance: Regular inspection and maintenance
labels are proudly pasted on each and every fire of fire damper is essential. NFPA 80 – standard for
damper. The installation has to be carried out fire doors and other opening protective states that
strictly as per the installation instructions that is sent fire dampers shall require inspection and testing
along with every shipment. one year after installation. Follow up testing and
inspection shall be done every 4 years except in
hospitals where the frequency shall be 6 years.
Most common installation errors to be avoided:
2015 Edition.
Copyright reserved. Specifications subject to change without notice.
05 www.airmasteremirates.com
19.2 CURTAIN TYPE
FIRE DAMPER CURTAIN TYPE FIRE DAMPER
Model : AFD-3
3 hrs Fire Rating
CONSTRUCTION:
Frame: High quality galvanized steel sheet of Spring: Constant force stainless steel springs
thickness 16 gauge. on both sides.
Blades: Interlocking type roll formed blades UL listed Fusible Links: 165o F fire rating as
of thickness 20 gauge. standard.
Blade Ramp: 16 gauge thick galvanized steel
with a spring holder.
Description:
• The interlocking type blades are designed with hat shaped reinforcement
ridges ensuring strength and stability.
• The frame is designed to keep blades out of airstream to prevent dust and
contamination.
• All corners of the frame are fully welded (and painted to prevent rust) to
ensure sturdy construction.
• AFD-3 model fire dampers are UL 555
classified & manufactured under Airmaster’s
strict quality control procedures.
Maximum Mounting
Section Fire Rating Wall Type
Size W x H Position
Single 42" x 42" Vertical 3 Masonry/Gypsum
Options:
• Frame: Round or Oval Inlet/Outlet.
• Sleeve: Provided only on request with sheet thickness 16 gauge.
• UL listed Fusible link: 212oF fire rating up to 27” x 41”(for vertical application only).
• Micro switch: To know the status of damper’s blade open & close position.
2015 Edition.
www.airmasteremirates.com 06 Copyright reserved. Specifications subject to change without notice.
CURTAIN TYPE 19.3
FIRE DAMPER
Model : AFD-3
Dimensional Details:
How to order:
Limit Switch With Sleeve
Size (mm/inch) Quantity (no.)
(Yes/No) (Yes/No)
500 x 500 250 No No
2015 Edition.
Copyright reserved. Specifications subject to change without notice.
07 www.airmasteremirates.com
19.4 MOTORIZED
FIRE DAMPER MOTORIZED FIRE DAMPER
Model : AMFD 1.5 hrs Fire Rating
CONSTRUCTION:
Frame: High quality galvanized steel sheet of T.R.D : Belimo (UL listed), temperature rating -
thickness 16 gauge. 165oF.
Blades: Single skin roll formed from high Jamb Seal: Stainless steel.
quality steel sheet of thickness 16 gauge.
Description:
• All corners of the frame are fully welded (and painted
to prevent rust) to ensure sturdy construction for a
rattle free operation.
• All AMFD models are factory fitted with 400mm wide &
1.2mm thick steel sleeve as standard and the entire
assembly can comfortably seat through 8” thick wall.
• All dampers and TRD’s are factory tested before dispatch to ensure smooth operation
in the field.
• Can be used in Masonry and Gypsum walls/partitions of less than 3 hours fire resistance rating as per
NFPA 90-A in accordance with ANSI/UL555 standards.
• Maximum Approved
. Size:
• Multiple section : 70” x 70” (vertical installation / Static application only)
• Single section : 35” x 35” (vertical installation / Static & Dynamic application).
2015 Edition.
www.airmasteremirates.com 08 Copyright reserved. Specifications subject to change without notice.
MOTORIZED 19.5
FIRE DAMPER
Model : AMFD
Options:
• Gasket: UL approved gasket
• Actuator Position: Counter Clockwise direction (CCW)
• Operating Voltage: 24VAC / 120VAC
• Auxiliary Switch: Actuator with inbuilt auxiliary switch
Dimensional Details:
How to order:
Actuator Auxiliary
Size Gasket
Qty (no.) Voltage Position Switch
(mm/inch) (Yes/No)
(CW/CCW) (Yes/No)
400 x 400 100 240VAC CW Yes Yes
2015 Edition.
Copyright reserved. Specifications subject to change without notice.
09 www.airmasteremirates.com
19.6
MOTORIZED FIRE & SMOKE
DAMPER
MOTORIZED FIRE & SMOKE DAMPER
1.5 hrs Fire Rating
Model : AMFSD
CONSTRUCTION:
Frame: High quality galvanized steel sheet of T.R.D : Belimo (UL listed),temperature
thickness 16 gauge. rating -165oF.
Blades: Single skin roll formed from high Jamb Seal: Stainless steel.
quality steel sheet of thickness 16 gauge.
Gasket : UL listed gasket.
Actuator: Honeywell, 9NM torque (UL listed).
Description:
• All corners of the frame are fully welded (and
painted to prevent rust) to ensure sturdy
construction for a rattle free operation.
• All AMFSD models are factory fitted with 400mm wide & 1.2mm thick steel sleeve
as standard and the entire assembly can comfortably seat on 8” thick wall.
• All dampers and TRD’s are factory tested before dispatch to ensure smooth operation
in the field.
• Actuators have to be configured with control panel or BMS system for smoke control
applications before commissioning.
• Can be used in Masonry and Gypsum walls/partitions of less than 3 hours fire resistance
rating as per NFPA 90-A in accordance with ANSI/UL555 standards.
2015 Edition.
www.airmasteremirates.com 10 Copyright reserved. Specifications subject to change without notice.
19.7
MOTORIZED FIRE & SMOKE
DAMPER
Model : AMFSD
Dimensional Details:
How to order:
Actuator
Quantity Auxiliary Switch
Size (mm/inch) Voltage position
(Nos) (Yes/No)
(CW/CCW)
2015 Edition.
Copyright reserved. Specifications subject to change without notice.
11 www.airmasteremirates.com
19.8
MOTORIZED SMOKE
DAMPER
MOTORIZED SMOKE DAMPER
Model : AMSD 1.5 hrs Fire Rating
CONSTRUCTION:
Frame: High quality galvanized steel sheet of Jamb Seal: Stainless steel.
thickness 16 gauge.
Gasket : UL listed gasket.
Blades: Single skin roll formed from high
quality steel sheet of thickness 16 gauge.
Description:
• Available with Class II leakage, rated at 2000fpm (10.2m/s) / 4”w.g(1000pa).Suitable for most of the
commercial smoke management applications in both static and dynamic systems.
• All corners of the frame are fully welded (and painted to prevent rust) to make construction more sturdy for
a rattle free operation.
• Designed for parallel blade operation. Blades are linked together externally (out of airstream).
• AMSD series is UL 555S classified and manufactured under Airmaster’s strict quality control procedures..
• All actuators are externally mounted with 230VAC as standard and are supplied without inbuilt auxiliary
switch. The actuator can be controlled from command station.
• Factory fitted with 400mm wide & 1.2mm thick steel sleeve and the entire assembly can comfortably seat
on 8” thick wall.
• All dampers are factory tested to ensure smooth
operation before dispatch.
2015 Edition.
www.airmasteremirates.com 12 Copyright reserved. Specifications subject to change without notice.
19.9
MOTORIZED SMOKE
DAMPER
Model : AMSD
Options:
• Auxiliary Switch: Actuator with inbuilt auxiliary switch.
• Operating Voltage: 24VAC / 120VAC.
• Actuator Position: Counter Clockwise direction (CCW).
Dimensional Details:
How to order:
Actuator Auxiliary
Quantity TRD
Size (mm/inch) Voltage position Switch
(Nos) (Yes/No)
(CW/CCW) (Yes/No)
2015 Edition.
Copyright reserved. Specifications subject to change without notice.
13 www.airmasteremirates.com
19.10
FIRE
DAMPER HONEYWELL - CONTROLS
Model - MS4609F1010 :
• Line voltage (230 Vac), 9 (Nڄm) torque and without open
& close position-indicating switches.
Model - MS4609F1210 :
• Line voltage (230 Vac), 9 (Nڄm) torque and with open & close
position indicating switches.
Model - MS8109F1010:
• Line voltage (24 Vac), 9 (Nڄm) torque and without open &
close position-indicating switches.
Model - MS8109F1210 :
• Line voltage (24 Vac), 9 (Nڄm) torque and with open & close
position indicating switches.
Temperature Ratings :
• The actuator is designed to meet UL555S standards at 350°F (176°C).
Operation:
• In case of fire, damper operates on volt free signal to the actuator. i.e spring return
operation.
Mounting:
• Actuator can be used for either clockwise (CW) or counter clockwise (CCW) spring
return.
2015 Edition.
www.airmasteremirates.com 14 Copyright reserved. Specifications subject to change without notice.
3URWHFW \RXU EXLOGLQJ ZLWK ¶$'9$1&(·
)LUHUDWHGVWHHOGRRUV
!!!
#$%&'()(*)'(*')%&'()(*)(
+$%+;;<#+!#$#<+;#;!#
Non Return Dampers
air master
Non return damper
√ Wall mounted
Model: ANRD-W
Construction:
• Frame: High quality extruded aluminium profile
with 30 mm flange width as standard. 12, 16, 24
mm flange widths are optional.
• Blades: Aluminium sheet as standard. GI sheet
as option.
• Blade supports: Self oiling nylon bushings with
8 mm diameter aluminium rods.
• Blade seals: Foam gasket for air tightness.
• Blade stoper: 20 mm x 20 mm aluminium angle.
• Designed to maintain a constant pressure level
Description: inside pressurized rooms by relieving excess air
• Frame is of high quality extruded aluminium pro- when it exceeds the desired limit.
filed construction with the advantages of corro-
sion resistance and rigidity. • Generally installed on diesel generator, plant
rooms ventilation system and exhaust ducting.
• Air operated damper blades are fixed to the
frame by self oiling nylon bushes with 8 mm dia • Available in square and rectangular sizes.
aluminium pipes.
18.1
ISO 9002 certified company
Non Return Dampers
air master
Non return damper
√ Duct mounted
Model: ANRD-D
18.2
ISO 9002 certified company
DUCT REGULATING DAMPERS
R E G U L A T I N G
D A M P E R S
DD
SERIES
MANUFACTURERS OF AIR/FIRE/SMOKE CONTROL PRODUCTS
Product Description and Features
Introduction Blades
The DD Series Duct Balancing Damper was designed The 63mm wide extruded aluminium airfoil section
for duct installations to balance/regulate airflows. blades are fitted to 12.5mm diameter spindles, with the
option of galvanised mild steel or Grades 316 and 430
All spindles revolve in low maintenance nylon bushes
stainless steel blades available to order.
which are fitted within pressed inserts. Precise blade
positioning is achieved via a robust dual-purpose All models are available with either opposed or parallel
quadrant and spindle assembly, operating the linkage blades (unless specified, opposed blades will be
mechanism which is located outside of the airstream. supplied as standard).
The quadrant assembly is designed to facilitate simple Fitted to the ends of the aluminium blades are End
conversion to motorisation without the need for Caps to alleviate noise generation.
additional components.
Features
Plain
, Standard case construction is galvanised mild steel Aluminium
, Two airfoil blade designs Blade
Galvanised Mild
Steel or Stainless
Steel Blade
1
Dimensions
Flangefit 105
* * W * ‘Tear Drop’ Hole Detail
m
W x H = 100mm to
m
15
1000mm square 5.5 Rad.
Ņ
3.5 Rad.
B = 20mm, 25mm and
30mm to order H
m
Dims
m
(35mm standard)
24
+ 0.25mm
Spigotfit 40 85 40 55
30 W 30
W x H = 100mm to 30
1000mm square
30
Circular 85 55
* * 30 D 30
Spigotfit See Table Page 3
D = 100mm to 800mm
diameter
D H-D (Equidistant)
* = 40mm
(100-449mm dia.)
See Table Page 3
55mm
(450-800mm dia.)
Flat Oval
Spigotfit
W x H = 100mm to
1000mm spigots
2
Circular Spigotfit Dimensions
Multiple Assemblies
Illustrated below are several variants to multiple section For applications which necessitate the blades to be
units. Where sizes exceed 1000mm square, multi- installed vertically, BSB’s sales office must be informed
section units will be supplied. so that thrust bearings are fitted to eliminate blade
friction.
All multiple units are shipped as individual sections for
site assembly by others. Unless requested, joining It is recommended that for sizes greater than
strips would not normally be supplied drilled. 1000mm width or height, the HD Series Heavy Duty
Damper is used.
3
Control Options
Option E 50
Extended Spindle
When the specification requires the DD Series Damper
to be supplied for motorisation by others, BSB supplies
the damper with a 12.5mm diameter spindle, 50mm in
length, based on a 35mm flanged damper.
Option H
Hand Control
BSB’s unique hand lockable quadrant is supplied
complete from the factory.
When the specification is amended from Option “E” to
Option “H” conversion is easily completed.
Option M
Electric Motor
The DD Series Damper can be supplied with the
following control motors fitted:
Open/Close operation:
A = 70mm, 15Nm.
A = 80mm, 30Nm.
Spring Return operation:
A = 95mm, 15Nm.
For additional technical details, please contact BSB’s sales office for
data sheets to Option “M”.
Option P
Pneumatic Actuator
The model actuator used will be double rack and pinion design with bodies
manufactured of cast aluminium alloy.
The pneumatic actuator operates between 30psi/2bar and 120psi/8bar.
The pneumatic actuator is available as a Spring Return or Double Acting
model and will comply to PED 97/23/EC.
It is supplied fitted to the damper complete with integral threaded 1/4bsp
air-ports to pressurize and vent the actuator. Various accessories are available
including Solenoid Valves and Switch Boxes. ATEX rated models available.
For further information and technical advice, please contact BSB’s sales office.
4
Specification Tables
Torque Chart
Differential Damper Size (mm) These values have
been rounded up
Pressure 200 x 200 500 x 500 1000 x 1000 and down to whole
numbers and are
(Pa) Nm lb/ins Nm lb/ins Nm lb/ins illustrated for
500 2.0 18.0 4.0 35.0 7.5 66.0 estimation purposes
only.
1000 4.0 35.0 7.0 62.0 10.0 88.0
Performance Characteristics
800
Pressure Loss (Pa)
100
80
15° 700
60 Closed
600 625 Pa
50
40
30 500
20 400
Fully
10
8 Open
300
6 250 Pa
5
4 200
3
BSB Flangefit
2
600mm x 600mm l/sec l/sec/m2
1
1 2 3 4 5 6 7 8 9 10 15 200 300 400
Air Velocity (m/s) Air Leakage (l/s, l/sec/m2)
Max. velocity 15m/s = Measured Calibrations
5
Product Specifications
6
Ordering Codes DD Regulating Duct Damper
Example: Model:
F Flange-fit
DD F A - H S
C
Rectangular/Square Spigot-Fit
Circular Spigot-Fit
O Flat Oval Spigot-Fit
D A M P E R S
Blade Material:
Control
A Aluminium Airfoil Blades
Option
G Galvanised Steel Airfoil Blades
Blade Material S Stainless Steel Airfoil Blades (state Grade)
BSB Engineering Services Ltd. reserves the right to modify or withdraw any specification without A Member of The Maico Group
prior notice that may result from continuous product development. The information contained within
this brochure is correct at the time of going to press. BSBDD. Jun. 2008
ABU RKHAYA
LOUVERS TECHNICAL SUBMITTAL
Page Contents
2 Air Louvers
3 Air Louvers - Performance Data
5 Gravity Shutter
6 Gravity Shutter - Performance Data
7 Sand Trap Louvers
8 Sand Trap Louvers - Performance Data
9 Ordering System
10 Sand Louvers
14 Penthouse Louvers
20 Stationary Stormproof Louvers
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Air Louvers
Model: CI - Air L - H
CI - Air L - H
CI - Air L - H
Features:
Designed for use as air intakes or air exhaust louvers for commercial or industrial air conditioning systems.
Combines fine architectural design with good performance meets most requirements.
Louvers are completely weather proof and rain proof blade lips.
Can be provided with bird or insect screens, White and anodized aluminum are the standard color,
other colors are available upon request.
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Air Louvers
Performance Data
16
0.37 0.43 0.50 0.57 0.64 0.77 0.98 1.18 1.38 1.59 1.79 1.99 2.40
(41)
20
0.52 0.61 0.71 0.80 0.90 1.09 1.38 1.66 1.95 2.24 2.52 2.81 3.38
(51)
24
0.67 0.79 0.91 1.04 1.16 1.41 1.78 2.15 2.52 2.89 3.26 3.63 4.37
(61)
28
0.82 0.79 1.12 1.27 1.42 1.72 2.18 2.63 3.08 3.54 3.99 4.44 5.35
(71)
32
0.97 1.04 1.32 1.505 1.68 2.04 2.58 3.11 3.65 4.18 4.72 5.26 6.33
(81)
36
1.12 1.32 1.53 1.74 1.94 2.36 2.98 3.60 4.22 4.84 5.46 6.08 7.32
(91)
40
1.27 1.50 1.73 1.97 2.20 2.67 3.38 4.08 4.78 5.49 6.19 6.86 8.30
(102)
44
1.41 1.68 1.94 2.20 2.46 2.98 3.78 4.55 5.34 6.12 6.91 7.69 9.26
(112)
48
1.57 1.86 2.15 2.44 2.736 3.31 4.18 5.05 5.92 6.79 7.66 8.53 10.27
(122)
52(
1.72 2.03 2.35 2.67 2.99 3.62 4.58 5.53 6.48 7.44 8.39 9.34 11.25
(132)
56
1.87 2.21 2.56 2.90 2.25 3.94 4.98 6.01 7.05 8.08 9.12 10.16 12.23
(142)
60
2.02 2.39 2.67 3.14 3.51 4.26 5.38 6.50 7.62 8.74 9.86 10.98 13.22
(152)
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Air Louvers
Performance Data
Note: 1.0
For sizes not shown, the approximate free
area in square feet can be calculated by
using the formula below: 0.5
0.3
W= Width on feet
H= Height on feet 0.2
Ps)
Ps)
T (+
0.1
E (-
(Sq. Ft.) X (fpm)
US
AK
HA
INT
EX
Pressure Loss Inches w. g.
0.05
0.04
0.03
0.02
0.01
0.005
0.004
0.003
0.002
0.001
100 200 300 400 600 1000 2000 3000 4000 5000
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Gravity Shutter
Horizontal Operatable Pressure Relief Shutter
CI - Air GS-H
CI - Air GS-H
Features:
A horizontal operatable shutter which operates to equalize the pressure across it.
The frame and blades are constructed of extruded aluminum anodized as standard painted, powder
coated are available on request.
The frame has a typical wall thickness of 1/16” and separated from the movable blades by an extruded
rigid PVC track which is riveted to and becomes an integral part of the frame. A1/8” thick, 3/8” wide foam
tape is installed on the blades where they overlap to insure a good seal and to reduce noise.
Each shutter is carefully designed to equalize the pressure in such areas as a compressor of fan room with
the outside.
The blades are designed and positioned in such a way that if the pressure in the room increase the blades
automatically lift and open relieving the pressure in the room.
When the room pressure is normalized the blades drop to the closed position by gravity.
These devices are also employed at the end of exhaust ducts where they would open when the exhaust
fan was turned on and would close when the fan was turned off.
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Gravity Shutter
Performance Data
Listed Height
(Inches) 12 14 16 18 20 24 30 36 42 48 54 60 72
12 0.81 0.96 1.10 1.25 1.40 1.64 2.08 2.47 2.91 3.30 3.74 4.13 4.96
16 1.08 1.27 1.47 2.66 1.86 2.18 2.77 3.29 3.87 4.44 5.02 5.49 6.60
20 1.36 1.60 1.85 2.09 2.33 2.75 3.48 4.13 4.87 5.52 6.25 6.91 8.30
24 1.62 1.92 2.21 2.50 2.79 3.29 4.16 4.95 5.82 6.61 7.48 8.17 9.93
Listed Height
28 1.89 2.23 2.57 2.91 3.25 3.83 4.85 5.76 6.78 7.69 8.71 9.63 11.56
32 2.16 2.55 2.93 3.32 3.71 4.37 5.53 6.57 7.74 8.78 9.94 10.99 13.19
36 2.44 2.87 3.31 3.75 4.19 4.93 6.24 7.42 8.73 9.91 11.22 12.40 14.89
40 2.70 3.19 3.68 4.16 4.65 5.47 6.93 8.23 9.69 11.00 12.45 13.76 16.52
44 2.97 3.50 4.04 4.57 5.11 6.01 7.61 9.05 10.65 12.08 13.68 15.12 18.16
48 3.25 3.83 4.42 5.00 5.59 6.57 8.32 9.89 11.64 13.21 14.97 16.54 19.86
52 3.52 4.15 4.78 5.41 6.04 7.11 9.01 10.71 12.60 14.30 16.20 17.89 21.49
56 3.78 4.46 5.14 5.82 6.50 7.65 9.69 11.52 13.56 15.39 17.43 19.25 23.12
60 4.06 4.79 5.52 6.25 6.98 8.21 10.40 12.36 14.55 16.52 18.71 20.67 24.82
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Sand Trap Louvers
CI - Air SL-H
Features:
The sand trap louver is used to lower the dust loading of conventional filtration as it is designed to separate
large size sand particles at low to medium speeds.
It is also fitted with a bird screen mesh made of galvanized steel to protect against the unwanted objects.
The sand trap louver is a self emptying system, it has a set of holes at the bottom face of the casing to
discharge separated sand particles.
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Sand Trap Louvers
Performance Data
Performance:
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Sand Trap Louvers
Ordering System:
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Sand Louvers
CI - Air DL - H
General:
CIC Sand Louver CI - Air DL- H are architectural air inlets. They are
widely used for building exteriors and are suitable for different
HVAC and industrial applications to prevent sand entry.
CI - Air DL- H louvers have 2 inch deep horizontal fixed blades designed carefully for low pressure drop and
to prevent entry of sand.
The frame is 1.25” wide (flat or curved) flanged type and is mechanically joined to give a rugged
construction to the louver.
These louvers are available as optional with galvanized bird screen, aluminum type air filter in 1”, 2” and 4”
thickness and volume control damper.
They are manufactured in a wide range of standard sizes however, they can be supplied in non-standard
sizes, depths or architectural shapes to suit customers requirements.
CI - Air DL- H sand louvers are made of heavy extruded aluminium profiles.
They are available in white polyester powder coated finish or any other RAL standard colour upon
customer’s request.
Bird screens are made of galvanized expanded metal sheets.
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Sand Louvers
CI - Air DL - H
Product Code
Width in inch.
Height in inch.
Accessories:
B : Bird screen
D : Volume Control Damper (VCD)
BD : Bird screen & VCD.
I : Insect Screen.
F1 : Aluminium Filter 1” thick.
F2 : Aluminium Filter 2” thick.
F4 : Aluminium Filter 4” thick.
Use the code of CI - Air DL- H to refer to CIC sand louver with flat frame.
Example:
• CI - Air DL- H - 30 - 18 - B:
CIC Sand Louver - size 30” x 18” with bird screen.
• CI - Air DL- H - 24 - 20 BDF1:
CIC Sand Louver - size 24” x 20” with bird screen, volume control damper and 1” thick aluminium filter.
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Sand Louvers
CI - Air DL - H
Dimensional Data
Selection Procedure:
To select a suitable size of a sand louver (CI - Air DL- H) for a certain application, follow exactly the same
procedure as been explained previously.
Note:
The approximate effective free area in square feet can be calculated by using the following formula:-
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Sand Louvers
CI - Air DL - H
Performance Data
Pressure Requirement
Face Velocity (FPM) 200 300 400 500 600 700 800 900 1000 1200 1400 1600
Intake PD° W.G. 0.007 0.016 0.028 0.044 0.063 0.086 0.112 0.141 0.175 0.252 0.338 0.433
Table No. 2 Intake pressure drop in inches of water as a function of face velocity in FPM for CI - Air DL- H.
Table No. 3. Effective free area in ft² factor) for CI - Air DL- H.
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Penthouse Louvers
CI - Air PHL - H
General:
CIC penthouse louvers CI - Air PHL - H are considered as typical louver units for both air intake and exhaust
applications.
They are designed and built to become a permanent part of the building.
They maintain their pleasant appearance and effective weather protection as a result of their rugged,
durable, extruded aluminium construction and careful workmanship.
They are usually furnished with either mullion or mitered corners and incorporate the normal CIC fresh air
louver blades CI - Air PHL - H as standard. However, any other type of CIC louver blades can also be used
as optional.
Penthouse Louver (CI - Air PHL - H) Penthouse Louvers (CI - Air PHL - H)
With Mullion Corner With Mitered Corner
Description:
CI - Air PHL - H penthouse louvers have as a standard 2” deep fixed horizontal blades.
The blades are carefully designed to get low pressure drop, maximum free area and to prevent rain-water
penetration.
They are available in 1.25” flanged frame and are built and mounted to an internal framing with mullion
corners.
The integral framing mullion structures are furnished with a standard 1.6” x 1.6” extruded aluminium
profiles.
For the other mitered corners type penthouse louvers, blades are beveled and welded internally at the
end.
The top of the penthouses are covered with flat or pitched roofs of aluminium sheets.
All of the four louver sides are of removable type for easy maintenance purposes, Penthouse louvers can
also be supplied as optional with galvanized bird or insect screens and / or aluminium washable air filters
of 1”, 2”, or 4” thickness.
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Penthouse Louvers
CI - Air PHL - H
Product Code
CI - Air PHL - H penthouse louvers are made of heavy gauge extruded aluminium profiles. They are
available in white polyester powder coated finish or any other RAL standard colour upon customer’s
request.
Structural mullion corners are of strong aluminium profiles while roof tops are of aluminium sheets
as a standard.
However, galvanized roofs are also available upon request.
Bird screens are made of galvanized expanded metal sheets.
Width in inch.
Length in inch.
Height in inch.
Accessories:
B : Bird Screen
I : Insect Screen
F : Aluminium Filter 1” thick.
F2 : Aluminium Filter 2” thick.
F4 : Aluminium Filter 4” thick.
Example:
CI - Air PHL - H - 18 - 18 - 24 - B:
CIC penthouse louver with 18” x 18” basement
size, 24” height and bird screen.
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Penthouse Louvers
CI - Air PHL - H
Definitions
Definitions:
: Is the air stream velocity measured at the face of a louver in FPM
Face velocity
and it corresponds to the effective free area.
Total pressure drop : Is the sum of static pressure and velocity pressure given in inches W.G
CI - Air PHL - H - F2
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Penthouse Louvers
CI - Air PHL - H
Dimensional Data
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Penthouse Louvers
CI - Air PHL - H
Selection Procedure
Example:
Select a penthouse louver for an exhaust requirements of 3300 CFM with a total pressure drop of 0.1” W.G.
1) From the pressure requirement table 2 it shows that an 800 FPM velocity results an exhaust pressure
drop of 0.1” W.G.
2) Determine the effective free area:
CFM
Effective free area Ak =
Vk
3000
= = 4.125 ft2
800
3) From table 3 the 4.125 ft2 effective free area is suitable for the following penthouse louver’s sizes:
• P = 5 ft, H = 28 inch.
Could be suitable for a penthouse basement dimensions of (WxL) - 12” x 18”.
• P = 6 ft, H = 24 inch.
Could be suitable for a penthouse basement dimensions of (WxL) - 12”x24” or 18” x 18”
depending on the duct size.
Note:
The approximate effective free area in square feet can be calculated by using the following formula:-
Pressure Requirement:
Free Velocity (FPM) 200 300 400 500 600 700 800 900 1000 1200 1400 1600
Intake PD" W.G. 0.006 0.011 0.023 0.037 0.050 0.066 0.087 0.110 0.142 0.193 0.280 0.390
Exhaust PD" W.G. 0.007 0.014 0.028 0.044 0.059 0.080 0.10 0.128 0.159 0.255 0.310 0.425
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Inside Perimeter in feet (2W + 2L)
Height
(Inches)
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
12 0.875 1.125 1.375 1.625 1.875 2.125 2.375 2.625 2.875 3.125 3.375 3.625 3.875 4.125 4.375 4.625 4.875 5.125 5.375 5.625 5.875
16 1.458 1.875 2.292 2.708 3.125 3.542 3.958 4.375 4.792 5.208 5.625 6.042 6.458 6.875 7.292 7.708 8.125 8.542 8.958 9.375 9.792
CI - Air PHL - H
2.042 2.625 3.208 3.792 4.375 4.958 5.542 6.125 6.708 7.292 7.875 8.458 9.042 9.625 10.208 10.792 11.375 11.958 12.542 13.125 13.708
24 2.625 3.375 4.125 4.875 5.625 6.375 7.125 7.875 8.625 9.375 10.125 10.875 11.625 12.375 13.125 13.875 14.625 15.375 16.125 16.875 17.625
28 3.208 4.125 4.842 5.958 6.875 7.792 8.708 9.625 10.542 11.458 12.375 13.292 14.208 15.125 16.042 16.958 17.875 18.792 19.708 20.625 21.542
32 3.792 4.875 5.958 7.042 8.125 9.208 10.292 11.375 12.458 13.542 14.625 15.708 16.792 17.875 18.958 20.042 21.125 22.208 23.292 24.375 25.458
36 4.375 5.625 6.875 8.125 9.375 10.625 11.875 13.125 14.375 15.625 16.875 18.125 19.375 20.625 21.875 23.125 24.375 25.625 26.875 28.125 29.375
40 4.958 6.375 7.792 9.208 10.625 12.042 13.458 14.875 16.292 17.708 19.125 20.542 21.958 23.375 24.792 26.208 27.625 29.042 30.458 31.875 33.292
44 5.542 7.125 8.708 10.292 11.875 13.458 15.042 16.625 18.208 19.792 21.375 22.958 24.542 26.125 27.708 29.292 30.785 32.458 34.042 35.625 37.208
48 6.125 7.785 9.625 11.375 13.125 14.785 16.625 18.375 20.125 21.875 23.625 25.375 27.125 28.875 30.625 32.375 34.125 35.875 37.625 39.375 41.125
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
52 6.708 8.625 10.542 12.458 14.375 16.292 18.208 20.125 22.042 23.958 25.875 27.792 29.708 31.625 33.542 35.458 37.375 39.292 41.208 43.125 45.042
56 7.292 9.375 11.458 13.542 15.625 17.708 19.792 21.875 23.958 26.042 28.125 30.208 32.292 34.375 36.458 39.542 40.625 42.708 44.792 46.875 48.958
60 7.875 10.125 12.375 14.625 16.875 19.125 21.375 23.625 25.875 28.125 30.375 32.625 34.875 37.125 39.375 41.625 43.875 46.125 48.375 50.625 52.875
64 8.458 10.875 13.292 15.708 18.125 20.542 22.958 25.375 27.792 30.208 32.625 35.042 37.458 39.875 42.292 44.708 47.125 49.542 51.958 54.375 56.792
68 9.042 11.625 14.208 16.792 19.375 21.958 24.542 27.125 29.708 32.292 34.875 37.458 40.042 42.625 45.208 47.792 50.375 52.958 55.542 58.125 60.708
www.cic-jo.com
72 9.625 12.375 15.125 17.875 20.625 23.375 26.125 28.875 31.625 34.375 37.125 39.875 42.625 45.375 48.125 50.875 53.625 56.375 59.125 61.875 64.625
Table No. 5. Effective free area in ft2 (Ak Factor) for CI - Air PHL - H
19
Stationary Stormproof Louvers
CI - Air SSL - H
General:
Description:
Louvers can be supplied with galvanized bird or aluminium insect screen, volume control damper and
aluminium air filter of 1”, 2” and 4” thickness.
The filters are accessable from the side or backward of the louver depending upon type of installation and
must be specified by the customer.
These louvers are available in standard given sizes, however they can also be supplied in other requested
sizes and architectural shapes upon customers requirements.
CI - Air SSL-H louvers are made of heavy gauge extruded aluminium profiles.
They are available in white polyester powder coated finish or any other RAL standard colour upon
customer’s request.
Bird screens are made of galvanized expanded metal sheets.
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Stationary Stormproof Louvers
CI - Air SSL - H
Product Code & Dimensional Data
Width in inch.
Height in inch.
Accessories:
B : Bird Screen
D :Volume Control Damper (VCD)
BD :Bird screen & VCD.
I :Insect Screen
F1 :Aluminium Filter 1” thick.
F2 :Aluminium Filter 2” thick.
F3 :Aluminium Filter 4” thick.
Dimensional Data
Example:
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Stationary Stormproof Louvers
CI - Air SSL - H
Selection Procedure
Example:
Louver size required for an exhaust requirements of 1200 CFM with a total pressure drop of 0.07” W.G.
1) From the pressure requirement table 7 it shows that a 600 FPM velocity results an exhaust pressure
drop of 0.07” W.G.
2) Determine the effective free area:
CFM
Effective free area Ak =
Vk
1200
= = 2.0 ft2
600
3) From table 8 the 2.0 ft2 effective area is mostly suitable for the size 42” x 18”.
Note:
For other louver sizes not shown in table 8. The approximate effective free area in square feet can be
calculated by using the following formula:-
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
Stationary Stormproof Louvers
CI - Air SSL - H
Performance Data
Pressure Requirement:
Free Velocity (FPM) 200 300 400 500 600 700 800 900 1000 1200 1400 1600
Intake PD" W.G. 0.007 0.018 0.031 0.047 0.070 0.092 0.112 0.145 0.183 0.271 0.380 0.50
Table No. 7 Total pressure drop in inches of water as a function of face velocity in FPM for CI - Air SSL-H.
18 0.371 0.636 0.901 1.166 1.431 1.696 1.961 2.226 2.491 2.756 3.021 3.286 3.551 3.816
24 0.574 0.984 1.394 1.804 2.214 2.624 3.034 3.444 3.854 4.264 4.674 5.084 5.494 5.904
30 0.777 1.332 1.887 2.442 2.997 3.552 4.107 4.662 5.217 5.772 6.327 6.882 7.437 7.992
36 0.980 1.680 2.380 3.080 3.780 4.480 5.180 5.880 6.580 7.280 7.980 8.680 9.380 10.080
42 1.183 2.028 2.873 3.718 4.563 5.408 6.253 7.098 7.943 8.788 9.633 10.478 11.323 12.168
48 1.386 2.376 3.366 4.356 5.346 6.336 7.326 8.316 9.306 10.296 11.286 12.276 13.266 14.256
54 1.589 2.724 3.859 4.994 6.129 7.264 8.399 9.534 10.669 11.804 12.939 14.074 15.209 16.344
60 1.792 3.072 4.352 5.632 6.912 8.192 9.472 10.752 12.032 13.312 14.592 15.872 17.152 18.432
66 1.995 3.420 4.845 6.270 7.695 9.120 10.545 11.970 13.395 14.820 16.245 17.670 19.095 20.520
72 2.198 3.768 5.338 6.908 8.478 10.048 11.618 13.188 14.758 16.328 17.898 19.468 21.038 22.608
78 2.401 4.116 5.831 7.546 9.261 10.976 12.691 14.406 16.121 17.836 19.551 21.266 22.981 24.696
84 2.604 4.464 6.324 8.184 10.044 11.904 13.764 15.624 17.484 19.344 21.204 23.064 24.924 26.784
90 2.807 4.812 6.817 8.822 10.827 12.832 14.837 16.842 18.847 20.852 22.857 24.862 26.867 28.872
Table No. 8. Effective free area in ft² (Ak factor) for CI - Air SSL-H.
TRIAL MODE − a valid license will remove this message. See the keywords property of this PDF for more information.
P.O.Box: 5152, Amman 11953, Jordan
Phone: 962 – 65521305
Fax: 962 – 65521073
Facebook: Manteq Engineering