Professional Documents
Culture Documents
BDF-40V-288 USER - S Manual
BDF-40V-288 USER - S Manual
BDF-40V-288 USER - S Manual
reference!
before use!
Contents
Attentions!
1. The package shall be removed completely before use.;
2. Carrying or placing the products shall be strictly under the user’s manual. The specific
refer to page three “fourth: Transportation and Installation”.
3. When carry or move the products, it should be placed for 30 minutes and then apply power.
4. The compressor has delay protection function. It operates after powering on 3 minutes .
5. The product should be consecutively power-on for 3 to 4 hours. It could be store things in
batches after the inner temperature reach the setting temperature. It is forbidden to store
many things one time in case of freezing lack.
6. A designated person should be responsible for the product, checking and recording the
operation every day, to avoid accidents and ensure safe use.
7. The parameter should be all set when leave the factory. Please read the user’s manual
carefully if you need to change the parameter.
1
Product Overview
2
Instructions
1. Transportation
2. Installation
◆ The product should be put in a ◆ The place should be flat and firm. If not
well-ventilated place. The top and two stable, please slightly raise the front of
sides should be more than 10 cm, at least product, it would be easy to close the door.
15cm is required between the back and the We should put something on the plank if
wall, which is good for ventilating. place it in the carpet and polyester,
10cm
otherwise color would change and fade due
to heat radiation.
10cm cm
15
3
Instructions
◆ Keep away from fire sources and stove. ◆ Keeping away from damp and water, in
Avoid direct sunshine. case of rust and weakening insulation
◆ Do not allow it close to petrol, thinner and effect.
gas in case of danger. ◆ Avoid placing it into the environment
with low temperature.
◆ Do not put the product into the place
where hard to disconnect the operating
device.
◆ Using three-way outlet alone and proper ◆ Power cord shall not be pressed by
fuse,otherwise it might be in fire if other product itself and others in case of
electric appliance also in the outlet. being damaged and causing accidents.
◆ The back of product shall not press the
plug.
◆ The voltage is required between 187 and ◆ Please make the plug into the outlet
242V , if not, you should add voltage well to have a good connection.
stabilizer which at least 500w. ◆ Do not pull the power cord when plug
out in case plug inside become flexible
and out of line.
◆ Don not use slack power cord, plug and ◆Once the power cord being damaged,
outlet. professionals are asked to change it to
◆ You should check the power cord carefully avoid danger.
before use. It should not be pressed,
transformed, stretched, twisted and tied up in
case of fire.
4
Instructions
s
◆ If there exists flammable gas or leaking gas,
◆ Do not use flammability spray around
please do not touch the product and outlet,
turn off the valve first and then open the the products.
window, all in case of explosion.
5
Instructions
6
Instructions
VII. Placement
◆The goods inside refrigerator should put ◆ We’d better reduce the opening time and
into storage bags or containers with lids, in frequency, the door being closed. We can adjust
case of water evaporation. inner temperature according to requirements,
not to be too cold.
◆ Do not stick goods or vessel into the back ◆ Do not put goods closely, in case of
of refrigerator, in case of being frozen. affecting cooling air circulation.
1. Illustrate the control principle of refrigerator with freezer: the temperature of refrigerator
room stays at 5℃ and the freezer room is -38℃. The temperature range of refrigerator
is 2.0℃—8℃, freezer is -36℃—-40℃.
2. Illustrate the operating procedures of temperature settings.
Example 1:Changing the refrigerator default temperature from 5.0℃ to 6.0℃. The
operating procedures are as follows:
Example 2:Changing the freezer setting value from “-38℃”to“-40℃”, the operating procedures
are as follows:
Note:To avoid error setting, Change the other factory setting is not recommended apart
from the specified parameter.
Parameter interpretation: L0: chamber temperature; L1: high temperature alarm; L2:low
temperature alarm; L3:present voltage; L4:present ambient temperature; L5: Compressor
operating status L6:power on delay
Under the status of lock, press “lighting” and “buzzer cancel” for 5 seconds at the same
time, “refrigerator temperature” show the left sensor temperature, “freezer temperature” show the
right. It restored automatically 2 seconds later. The default refrigerator temperature is 5 ℃, and
freezer temperature is -38℃.
For the refrigerator, the default high temperature alarm is 10℃ and the default low
temperature alarm is 0℃. For the freezer, the default high temperature alarm is -30℃ and the
default low temperature alarm is -45℃.
Changing the refrigerator high and low temperature alarm set point.
Example 3:change the refrigerator high temperature alarm to 11℃ and the low temperature
alarm to 1℃. The operation steps are as follows:
8
Instructions
Example 4:For example, change the freezer high temperature alarm to -29℃ and the low
temperature alarm to- 46℃. The operation steps are as follows.
9
Instructions
5 Press “set” The value is saved and the keyboard
Save setting value will be automatically locked after 90
seconds without any operation.
Note:●When refrigerator-freezer is in an alarm state, you can press the “Cancel Buzzing”
to interrupt the buzzer alarm.
● If the power outage occurs, a fully charged spare battery allows alarm function to
maintain 72 hours.
●After the initial starting up or a longer period of outage, to make the battery is
fully charged, it’s necessary for the refrigerator-freezer to run at least 48 hours.
●The battery storage capacity will be reduced with the increasing use, and also for
the alarm time after outage, so when the product is energized continuously for
three years, the battery should be replaced (by professionals from company) in
order to avoid losses.
10
Instructions
The freezer changes to “OFF”, and
Press “Adjust Temp.”
then close down
The value is saved and the keyboard
Save the setting
3 Press “set” will be automatically locked after 90
value an lock
seconds without any operation.
Note:Restarting the refrigerator or freezer, please change “OFF” to “ON” according to
the above method.
XIII. Defrosting
★ Refrigerator defrosting
Refrigerator automatically defrost, wall condensation will be discharged at any time through
12
Instructions
Instructions
the drainage.
★ Freezer defrosting
1. After operating for a period of time, the surface of freezer compressor、freezer inside and
drawer surface all covered with frost, which would affect the refrigeration effect and increase
power consumption. Defrosting is required when the thickness is more than 5mm.
2. Press “Freezer Defrost” for 5 seconds, and freezer compressor stops working. At the same
time, the “Freezer Temp.” shows “dF”, and the freezer starts defrosting. After defrosting, press
“Freezer Defrost” for 5 seconds again to make freezer compressor restart.
The unit shall be maintained regularly. Before maintenance, the power supply shall be cut off at
first to ensure safety.
1. The freezer can only be energized five minutes after the power supply was cut off to avoid
damaging the compressor.
2. Cleaning the inner every once in a while(the defrosting time is better),at first, with soft cloth
and a little non-corrosive neutral cleaning agent, then cleaning with water,dry cloth at last.
Note:It is forbidden to water the outer directly avoid affecting the function of electric insulation.
Please do not take abrasive powder、detergent、alkaline detergent、alcohol、gasoline、
acid、corrosive cleaner and hard brush to wash.
3. The dust deposited on the back, left and right side board and back shield of the unit shall be
cleaned frequently to improve the radiation efficiency and keep good ventilation.
4. Before the unit was laid up, the power plug shall be pulled out, the unit shall be cleaned
completely and wiped with dry cloth and the door shall be kept open for several days to
maintain dryness in the freezer. Operating several times during the periods(Don't be laid up
for a long time) 。
Notice!
Every unit has the possibility to get troubles. Please under the guidance as follows to
avoid loss during the units get troubles:
1、 Do not place the products into compact area.it shall be normally in and out in terms of
the area. All of these could prevent repairing difficulty once the products get trouble,
and the storage damages.
2、 Please refer to manuals first when product is abnormal or power failure. If it does not
work or supply power in a short time, please take the storage into other places in case of
damaging.
3、 Please ensure the temperature of storage meet the products before store, in case the
storage are damaged due to temperature difference, causing loss.
4、 Due to refrigerating inertia, there exists temperature difference inside the fridge .Besides, actual
temperature may differ with setting temperature. All of these are normal.
13
Instructions
14
Instructions
XVI. Troubleshooting
The cooling
The goods are hot or Put a little after cooling and
temperature can’t meet
crowded. reduce quantities.
the requirement. Open the door frequently or
Close the door tightly.
not well closed.
The equipment is subject to
sunlight or close to heat Keep away from heat source.
source.
Ventilating is not good. Set place for ventilating.
Too much frost. Defrosting
The goods of
The setting temperature is very Reset the temperature.
refrigerating chamber
low.
frozen.
Items close to the back of the cold Keep goods away from
source back
15
Instructions and Technical Parameters
Warning:We will continue to develop our products and then the specifications will change
accordingly. Please refer to the nameplate on the back of the product.
16