Professional Documents
Culture Documents
SRI986 Electro-Pneumatic Positioner: Product Specifications
SRI986 Electro-Pneumatic Positioner: Product Specifications
•The SRI986 Positioner is for operation of pneumatic valve actuators from control systems and electrical controllers
with electric control signals. It is used to reduce the adverse effects of valve friction, for higher thrust and shorter
positioning time.
FEATURES
• Independent adjustment of stroke range and zero • Explosion protection:
• Adjustable amplification and damping II 2 G EEx ia IIC T6 according to ATEX or
• Split range up to 3-fold possible intrinsic safe according to FM and CSA
• Input signal 0/4 to 20 mA, 0/2 to 10 V • EMC in accordance with the international stan-
dards and laws
• Supply pressure up to 6 bar (90 psig)
• Modular system of additional equipment
• Low vibration effect in all directions
- Limit switches
• Mounting according to IEC 534, part 6 (NAMUR) - Position transmitter
• Rotation adapter for angles up to 120 - Booster
- Connection manifold
2 SRI986 PSS EVE0102 A-(en)
TECHNICAL DATA
Input
Signal range . . . . . . . . . . . . 4 ... 20 mA or
Response characteristic 2)
0 ... 20 mA or Amplification . . . . . . . . . . . . adjustable
2 ... 10 V (On request) or Sensitivity . . . . . . . . . . . . . . < 0.1 % F.S.
0 ... 10 V (On request) Non-linearity (terminal
Input resistance . . . . . . . . . . < 200 Ohms at 20 °C based adjustment) . . . . . . . . < 1.0 % F.S.
Stroke range . . . . . . . . . . . . 8 ... 100 mm (0.3 ... 4 in) Hysteresis . . . . . . . . . . . . . . < 0.3 % F.S.
Angular range Supply air dependency. . . . . < 0.3 % / 0.1 bar (1.5 psi)
linear. . . . . . . . . . . . . . . . . 30 ° ... 120 ° Temperature effect. . . . . . . . < 0.5 % / 10 K
equal percentage . . . . . . . 90 °; from 70 ° linear
Air consumption
Output Air consumption single acting
Output to actuator . . . . . . . . 0 ... 100 % supply air pressure Supply air 1.4 bar (20 psig) 200 ln/h ( 7.1 scfh)
Supply air 3.0 bar (45 psig) 400 ln/h (12.4 scfh)
Supply Supply air 6.0 bar (90 psig) 600 ln/h (21.2 scfh)
Air consumption double acting
Supply air pressure . . . . . . . 1.4 ... 6 bar (20 ... 90 psig) Supply air 1.4 bar (20 psig) 350 ln/h (10.6 scfh)
Air supply. . . . . . . . . . . . . . . according to ISO 8573-1 Supply air 3.0 bar (45 psig) 550 ln/h (17.7 scfh)
- Solid particle size and density class 2 Supply air 6.0 bar (90 psig) 750 ln/h (33.5 scfh)
- Oil rate . . . . . . . . . . . . . . class 3
- Pressure dew point 10 K under ambient temperature
Air output
The use of filter regulator for air supply of positioner is
strongly recommended. It reduces the air pressure to Load effect 3) . . . . . . . . . . . . –3 % for delivery flow
actuator’s maximum pressure and keeps it constant. 2350 ln/h (83 scfh)
+3 % for exhausted flow
Ambient conditions 1900 ln/h (67 scfh)
Ambient temperature 1) . . . . . –40 ... 80°C (–40 ... 176°F) Capacity at max. deviation
Relative humidity . . . . . . . . . up to 100 %
Supply air
Operating conditions 1.4 2 4 6
pressure
according to IEC 654-1. . . . . The device can be operated (20) (30) (60) (90)
bar (psig)
at a class D2 location
without
Transport and 2 700 3 500 5 500 7 500
booster
storage temperature. . . . . . . –50 ... 80°C (–58 ... 176°F) (95) (124) (194) (265)
ln/h (scfh)
Storage conditions with booster
acc. to IEC 60 721-3-1 . . . . 1K5, 1B1, 1C2, 1S3, 1M2 18 000 24 000 40 000 55 000
VKXG-FN/GN
Protection class . . . . . . . . . . IP 54; IP65 as an option (636) (847) (1 492) (1 942)
ln/h (scfh)
IP65 protection class can be selected from model code with booster
option –F or can be retrofit on existing device by ordering 36 000 48 000 80 000 110 000
VKXG-HN
the kit EW 411 406 301. (1 271) (1 695) (2 825) (3 884)
ln/h (scfh)
CE marking
Electromagnetic compatibility 2004/108/EC
Low-voltage regulation . . . . . not applicable
1) Note the section “Explosion protection” on pages 6 and 7 with respect
to explosion-protected equipment
2) Data based on the following parameters:
stroke 30 mm (1.28 in), range spring FES 628/1,
feedback lever 117.5 mm ( 4.63 in), max. amplification,
supply air pressure 3 bar (45 psig)
3) Measured at air supply 1.4 bar (20 psig) and 50 % of the signal range
PSS EVE0102 A-(en) SRI986 3
Materials Connection
Housing . . . . . . . . . . . . . . . . Aluminum (Alloy No. 230) Pneumatic . . . . . . . . . . . . . . Female threads
finished with DD-varnish G 1/8 acc. to ISO 228
grey blue Electric
All moving parts of Line entry . . . . . . . . . . . . . 1 or 2 cable glands
feedback system . . . . . . . . . WNr. 1.4305 / 1.4571 M20 x 1.5 or 1/2-14 NPT
Mounting bracket . . . . . . . . . Aluminum (Alloy No. 230) (others with Adapter AD-...)
Cable diameter. . . . . . . . . 6 -12 mm (0.24 - 0.47 in)
Weight Screw terminals . . . . . . . . Screw terminals for wires
single acting. . . . . . . . . . . . . approx. 1.5 kg (3.3 lbs) up to 2.5 mm2 (AWG 14)
double acting . . . . . . . . . . . . approx. 1.8 kg (3.9 lbs)
Attachment kit Mounting
for diaphragm actuators. . . approx. 0.3 kg (0.6 lbs) Type of mounting . . . . . . . . . for attaching to diaphragm
for rotary actuators . . . . . . approx. 0.5 kg (1.1 lbs) actuators acc. to IEC 534-6
(NAMUR) and to rotary
actuators
Mounting orientation. . . . . . . any
4 SRI986 PSS EVE0102 A-(en)
ADDITIONAL EQUIPMENT
Additional equipment is installed by the manufacturer, but Limit Switch Assembly with Micro-switches
some types can also be put in later on. Therefore special Code V
part sets are available.
Input . . . . . . . . . . . . . . . . . . Stroke / angle from actuator
via positioner feedback lever
Inductive Limit Switch, two-wire system Output . . . . . . . . . . . . . . . . . 2 micro switches 2) 5)
Code P, Q, T, U Connected load, alternating current
Input . . . . . . . . . . . . . . . . . . Stroke / angle from actuator Switching capacity. . . . . . . max. 250 VA
via positioner feedback lever Switching voltage . . . . . . . max. 250 V
Output . . . . . . . . . . . . . . . . . 2 inductive proximity sensors Switching current with
acc. to DIN 19 234 resp. ohmic resistance . . . . . . max. 5 A
NAMUR for connection to inductive resistance . . . . max. 2 A
a switching amplifier with Bulb, metal filament . . . . max. 0.5 A
an intrinsically safe control Connected load, direct current
circuit 1) 2) 3) Switching Ohmic Inductive
Current consumption voltage, max. load load
Vane clear. . . . . . . . . . . . . > 3 mA V A A
Vane interposed . . . . . . . . < 1 mA
30 5 3
for control circuit with the following electrical values
50 1 1
Supply voltage . . . . . . . . . DC 8 V, Ri approx. 1 kOhms
75 0.75 0.75
Residual ripple . . . . . . . . . < 5 %
125 0.5 0.03
Permissible
250 0.25 0.03
line resistance . . . . . . . . . . < 100 Ohms
Response characteristic 6)
Reponse characteristic 6)
Gain . . . . . . . . . . . . . . . . . continuously adjustable
Gain . . . . . . . . . . . . . . . . . continuously adjustable
from 1:1 to approx. 7:1
from 1:1 to approx. 7:1
Switching differential . . . . . < 1 %
Switching differential . . . . . < 2.5 %
Switching point
Switching point
repeatability. . . . . . . . . . . . < 0.2 %
repeatability. . . . . . . . . . . . < 0.2 %
EMC . . . . . . . . . . . . . . . . . . acc. to EN 60 947-5-2
Part set for later installation EW 420 421 026
Part set for later installation
Code P, Q. . . . . . . . . . . . . not available
Code T . . . . . . . . . . . . . . . EW 419 510 343
Connection Manifold with Gauges
Code U . . . . . . . . . . . . . . . EW 419 510 361
Code JN, MN, RN, SN
Indicating range . . . . . . . . . . 0 ... 10 bar (0 ... 150 psig)
Inductive Limit Switch, three-wire system Error limit . . . . . . . . . . . . . . . class 1.6
Code R Pneum. connections. . . . . . . Female threads
Q1/4-18 NPT
Input . . . . . . . . . . . . . . . . . . Stroke / angle from actuator
acc. to DIN 45 141
via positioner feedback lever
Output . . . . . . . . . . . . . . . . . 2 inductive proximity sensors,
three-wire system,
LED indication,
contact, pnp 2) 4)
Supply voltage US . . . . . . . . DC 10 ... 30 V
Residual ripple . . . . . . . . . . . ± 10 %, Us = 30 V
Switching frequency . . . . . . . 2 kHz
Constant current . . . . . . . . . 100 mA
Response characteristic 6)
Gain . . . . . . . . . . . . . . . . . continuously adjustable
from 1:1 to approx. 7:1 1) For the standard version Code P, T one switching amplifier is required.
Switching differential . . . . . < 1 % For the security version Code Q, U a fail-safe amplifier for each
inductive proximity sensor is required.
Switching point 2) Operating mode min. (=low) / max. (=high) selectable by adjustment
repeatability. . . . . . . . . . . . < 0.2 % of switch vanes
3) Operating mode normally closed circuit / normally open circuit
Part set for later installation . EW 419 510 307 selectable at switch amplifier output
4) Contact closed within the positive range
5) Contact open within the positive range
6) For feedback lever effective length 117.5 mm (4.63 in),
stroke 30 mm (1.28 in) and maximum gain
PSS EVE0102 A-(en) SRI986 5
Electrical Position Transmitter Common data 2)
Code F Ambient conditions
Sensor. . . . . . . . . . . . . . . . . resistive precision Ambient temperature 3) 4) . . –25 ... 80 °C (–13 ... 176 °F)
conductive plastic element –40 ... 80 °C (–40 ... 176 °F)
Input . . . . . . . . . . . . . . . . . . Stroke / angle from actuator Relative humidity. . . . . . . . up to 100 %
via positioner feedback lever Operating conditons
Stroke range . . . . . . . . . . . 8 ... 100 mm (0.3 ... 4 in) according to IEC 654-1 . . . The device can be operated
Angular range . . . . . . . . . . 60 ... 120 ° at a class D2 location
Output . . . . . . . . . . . . . . . . . two-wire system Transport and
Signal range . . . . . . . . . . . 4 ... 20 mA storage temperature . . . . . –40 ... 80 °C (–40 ... 176 °F)
U − 12V Protection class. . . . . . . . . IP 54, IP65
Permitted load. . . . . . . . . . RBmax = S
0.02A
(US = Supply voltage) Mounting . . . . . . . . . . . . . . . attachment to positioner
1) For feedback lever with effective length 117.5 mm (4.63 in) and
stroke 30 mm (1.28 in)
2) Except manifold with gauges
3) Note the section “Explosion protection” on pages 6 and 7 with respect
to explosion-protected equipment.
4) –40 ... 80 °C (–40 ... 176 °F) for the fail-safe version of inductive
limit switch Code Q, U
6 SRI986 PSS EVE0102 A-(en)
The control circuit is galvanically separate from earth and all The supply- and signal circuits are galvanically separate
other electric circuits. from earth and from all other electric circuits.
1)
Explosion protection according to FM and CSA
Electro-pneumatic positioner type BIM 633
Intrinsically safe, Class I, Division 1,
Groups A, B, C, D, hazardous locations
Version
Single Acting . . . . . . . . . . . . . . . . . . . . . . . . . -B
Double Acting. . . . . . . . . . . . . . . . . . . . . . . . . -C
Input
Signal Range 4 - 20 mA . . . . . . . . . . . . . . . . . . . . . . . -I
Mode of Action
Direct Version: Increasing Input increases Output . . . . . . . . . . . . . D
Reverse Version: Increasing Input decreases Output . . . . . . . . . . . . R
Built-In Limit Switch/Position Transmitter
Without . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S
Inductive Limit Switch Three-Wire Technique, Without Explosion Protection . (a) . . R
Inductive Limit Switch (Standard Version) . . . . . . . (a) . . . . . . . . . . . . . T
Inductive Limit Switch (Security Version) . . . . . . . . (a) . . . . . . . . . . . . . U
Two Micro Switches, Without Explosion Protection. . . (a) . . . . . . . . . . . . . V
Position Transmitter 4 - 20 mA. . . . . . . . . . . . . (a) . . . . . . . . . . . . . F
Cable Entry
1/2"-14 NPT (with Adapter(s) M20x1.5 to 1/2"-14 NPT) . . . . . . . . . . . . . . . . . . . 6
M20 x 1.5 With One Plastic Cable Gland, Color Gray . . . . . . . . . . . . . . . . . . . . 7
Electrical Certification: (Only Standard Device)
II 2 G EEx ia IIC T6 according to ATEX . . . . . . . . (d) . . . . . . . . . . . . . . . . . . . EAA
FM Approved For Intrinsic Safety Cl. I, Div. 1, Groups A,B,C,D Hazardous Locations Indoors . . FAA
CSA Approved For Intrinsic Safety Cl. I, Div. 1, Groups A,B,C,D Hazardous Locations Indoors. . CAA
GOST Approved For Intrinsic Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GAA
Without . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ZZZ
Attachment Kit
Order as Auxiliary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N
Manifold
Order as Auxiliary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A
Options
Amplifier Free Of Nonferrous Metals . . . . . . . . . . (a) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -C
Protection Class IP65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -F
Designed For Auxiliary Energy Oxygen Max 6 Bar (With BAM Certificate) . . . . . . . . . . . . . . . . . . . . . . . -S
LLoyd's Register of Shipping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -X
Certificate EN 10204-2.1 - Certificate of compliance with the order . . . . . . . . . . . . . . . . . . . . . . . . . . . -1
Tag No. Labeling
Stamped With Weather Resistant Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -G
Stainless Steel Label Fixed With Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -L
Footnotes
a) Not available with FAA & CAA
d) Not available with Limit Switch Codes R, V
PSS EVE0102 A-(en) SRI986 9
MODEL CODES Accessories
Attachment kit EBZG
for diaphragm actuators with casting yoke acc. to NAMUR (incl. standard Couple lever) (for SRI986) . . . . . . . . . -HN
for diaphragm actuators with pillar yoke acc. to NAMUR (incl. standard Couple lever) (for SRI986) . . . . . . . . . . . -KN
for rotary actuators, without flange, 3 drill holes 6.5 mm (for SRP981, SRI983, SRI986, SMP981, SMI983, SGE985). . -PN
for rotary actuators, without flange, 4 threads M6 (for SRP981, SRI983, SRI986, SMP981, SMI983, SGE985) . . . . . -NN
for rotary actuators, with flange (for SRP981, SRI983, SRI986, SMP981, SMI983, SGE985) . . . . . . . . . . . . . . -JN
for rotary actuators, with shaft (for SRP981, SRI983, SRI986, SMP981, SMI983, SGE985) . . . . . . . . . . . . . . -ZN
for Masoneilan type Camflex II (for SRP981, SRI983, SRI986, SMP981, SMI983, SGE985) . . . . . . . . . . . . . . -RN
Further Attachment kits on request. See also http://www.foxboro-eckardt.eu/products/positioners_en /Attachment Kits
DIMENSIONS SRI986
5 2 4
m m
in
3 9 1 0 5 ,5
1 .5 4 4 .1 5
1 2 ,5 8 0
.4 9 3 .1 5
1 2 ,5
.4 9
1 .9 3
4 9
4 .0 6
1 0 3
m a x . 3 9
2 .0 5
5 2
m in . 4
1 1 4 ,5
4 .5 1
2 .8 3
7 2
3 .1 5
8 0
M 6
1 8 ,5
.7 3
2 4 2 2 2 2
.9 4 .8 7 .8 7
9
.3 5
3
.1 2
6 3
2 .4 8
6 7 8 9 1 0 6 ,7 ,8 3 1 2
144
1 A B 2 5.67
42 41 52 51 1 2 3 4 42 41 52 51 m m
in
41/51 2 41
3/4 42
DC DC
51
42/52 1 52
3 1 3 2
1 4 4
1 4 2 5 .6 7
1 Cable gland
2 Dummy plug, can be replaced with 1
3 Connection terminals (+/–)
4 Ground connection
A Limit switch
B Limit switch
12 SRI986 PSS EVE0102 A-(en)
7,8 -0,05
.31 -.002
M6
6 83 72 14
.24 3.27 2.83 .55
10
65 .39
7,9 +0,2
.31 +.01
2.56
.78
20
10
.39
91
3.58
m m
in
3.54
90
1.69
43
55,5
2.19
11
.43
102 102
4.02 4.02
63,5 63,5
2.50 2.50
20 ... 35
.79 ... 1.38
1.69
43
2 pieces
55,5
2.19
2.19
.41 55,5
10,4
10,4
.41
105,5
105,5
4.15
4.15
PSS EVE0102 A-(en) SRI986 13
DIMENSIONS Attachment Kit for Rotary Actuators
.47
12
.39
10
2.95 .01
75 0,2
136,5
2.36 .01
5.37
60 0,2
62,5
2.46
50
1.97
.2 ,5
6
6
1.10 +.02
28 +0,5
Detail Z
176,5
6.95
M6 x 14 (2 x)
14 DIN 912
.5 5
4,5
.18
2.76
70
.31
4 M6 x 30 (2 x)
8
.20
5
.16 DIN 912
6
.5 3
m m
6
.12
3
13, 5
in 47 .24
1.85
.39
10
. 53 54
2.13
63
2.48
86
3.39
50 M6
1.97
136,5
5.37
62,5
2.46
2.52
64
.47
12
3.90
99
16 H8
.63
1.18
30
167
6.57
45 0,2
6,5 14 - 6 1.77 .01
/
.55 - .24
.59 .01
.26
15 0,2
2.52
64
14 ... 15,5
M6
.47
12
.63
.47
12
22
.87
DIMENSIONS Booster
1 3 2 6 1 5 2 6
65,5
2.58
3.43
87
88 91
3.46 3.58
104 108
4.09 4.25
4 1 3 2 6
m m
in
3.35
85
104 83
4.09 3.27
4 1 3 2 4 1 3 2
6 6
28,5
1.12
28,5
88 30 1.12 88 30
3.46 1.18 3.46 1.18
6 1
5 2
3
4 3 ,5
1 .7 2
8 7 0
2 .7 6
1 0 2
4 .0 2
4
Connec-
5 6 7
tion single double
Gauge for Gauge for Gauge for
Manifold acting acting
Supply air Output I (y / y1) Output II (y2)
Code
JN Supply air Output (y) without yes -
MN Supply air Output I (y1) Output II (y2) - yes
RN without without without yes -
SN Supply air Output I (y1) Output II (y2) - yes
Subject to alterations - reprinting, copying and translation prohibited. Products and publications are normally
quoted here without reference to existing patents, registered utility models or trademarks. The lack of any such
reference does not justify the assumption that a product or symbol is free.