Professional Documents
Culture Documents
2955 2430 00 - XAHS 447 CD - XAHS 950 CD7 ASL Book PDF
2955 2430 00 - XAHS 447 CD - XAHS 950 CD7 ASL Book PDF
Parts Lists............................................................................................... 19
Printed Matter N°
2955 2430 00
ATLAS COPCO - PORTABLE ENERGY DIVISION
www.atlascopco.com 05/2012
-4-
PARTS INDEX
-5-
PARTS INDEX
-6-
PARTS INDEX
-7-
PARTS INDEX
V
VALVE.........50, 62, 73, 74, 76, 84, 127, 188, 190, 192, 196, 200, 204, 257
VALVE OIL STOP ..................................................................................121
VALVE REGULATOR ....................................................90, 91, 92, 93, 237
VALVES ON ELEMENT ..........................................................................73
VALVES ON VESSEL ............................................................73, 74, 75, 76
VENTIL...................................................................168, 170, 172, 174, 176
VESSEL........................... 90, 91, 92, 93, 111, 112, 113, 132, 133, 135, 237
VESSEL AND REGULATING VALVE ................................................237
VESSEL ASSEMBLY............................................. 111, 112, 113, 249, 256
VIBRATION DAMPER ............................................................................73
W
WARNING SWITCH ................................................................................60
WHEEL ...........................................................168, 170, 172, 174, 176, 254
WHEEL CHOCKS ..................................................................................223
WIRE .......................................................................................................156
WIRE HARNESS............................................................. 50, 216, 218, 220
WIRING ....................................50, 129, 136, 138, 181, 182, 185, 216, 220
Y
YOKE .............................................................................................263, 266
-8-
INSTRUCTION MANUAL
Warranty and Liability Limitation Limitación de garantía y responsabilidad Εγγύηση και Περιορισμός Ευθύνης
Use only authorized parts. Use sólo piezas autorizadas. Χρησιμοποιήστε μόνο εγκεκριμένα εξαρτήματα.
Any damage or malfunction caused by the use of unauthorized parts is not covered by La garantía o responsabilidad del producto no cubre ningún daño o funcionamiento Οποιαδήποτε ζημιά ή δυσλειτουργία προκληθεί από τη χρήση μη
Warranty or Product Liability. defectuoso provocado por el uso de piezas no autorizadas. εγκεκριμένων εξαρτημάτων δεν καλύπτεται από την εγγύηση και την ευθύνη
The manufacturer does not accept any liability for any damage arising for modifica- El fabricante no acepta ninguna responsabilidad por los daños provocados por modifi- για το προϊόν.
tions, additions or conversions made without the manufacturer's approval in writing. caciones, adiciones o conversiones realizadas sin la aprobación por escrito del fabri- Ο κατασκευαστής δεν αποδέχεται καμία ευθύνη για ζημιές που προκύπτουν
cante. από τροποποιήσεις, προσθήκες ή μετατροπές που έγιναν χωρίς τη γραπτή
Copyright 2012, Atlas Copco Airpower n.v., Antwerp, Belgium. έγκριση του κατασκευαστή.
Any unauthorized use or copying of the contents or any part thereof is prohibited. Derechos de reproducción 2012, Atlas Copco Airpower n.v., Amberes, Bélgica.
This applies in particular to trademarks, model denominations, part numbers and Está prohibida toda utilización o reproducción total o parcial no autorizada de estos Copyright 2012, Atlas Copco Airpower n.v., Αμβέρσα, Βέλγιο.
drawings contenidos, Απαγορεύεται οποιαδήποτε χρήση ή αντιγραφή του περιεχόμενου ή
en especial de las marcas registradas, denominaciones de modelos, números de piezas οποιουδήποτε τμήματος του παρόντος χωρίς εξουσιοδότηση.
y planos Αυτό ισχύει συγκεκριμένα για εμπορικά σήματα, ονομασίες μοντέλων,
Garantie- en aansprakelijkheidsbepalingen κωδικούς εξαρτημάτων και σχέδια.
Gebruik alleen originele onderdelen.
Beschadigingen of defecten die het gevolg zijn van het gebruik van niet originele Begränsningar av garanti och ansvarsskyldighet
onderdelen vallen niet onder garantie of productaansprakelijkheid. Använd endast godkända delar. Garanti og ansvarsbegrensning
De producent is niet aansprakelijk voor enige schade veroorzaakt door modificatie, Den skada eller funktionsoduglighet som förorsakats av att ej godkända delar har Bruk kun autoriserte deler.
toevoeging of ombouw, gemaakt zonder de schriftelijke toestemming van de fabri- använts, täcks inte av garantin eller produktansvaret. Enhver skade eller funksjonsfeil som skyldes bruk av uautoriserte deler dekkes ikke
kant. Tillverkaren accepterar ingen ansvarsskyldighet för skador som uppstått efter att av garanti eller produktansvar.
ändringar, tillägg eller ombyggnader gjorts utan skriftligt tillstånd från tillverkaren. Fabrikanten aksepterer intet ansvar for noen skade som oppstår på grunn av modifi-
Copyright 2012, Atlas Copco Airpower n.v., Antwerpen, België. kasjoner, tilføyelser eller forandringer som er gjort uten fabrikantens skriftlige tilla-
Het is niet toegestaan om zonder toestemming de inhoud geheel of gedeeltelijk te Copyright 2012, Atlas Copco Airpower n.v., Antwerpen, Belgien. telse.
kopiëren of anderszins te gebruiken. Ej auktoriserad användning eller kopiering av innehållet, eller delar av det, är förbju-
Dit betreft vooral trademarks, modelbenamingen, onderdeelnummers en tekeningen. den. Copyright 2012, Atlas Copco Airpower n.v., Antwerpen, Belgia.
Detta gäller speciellt varumärken, modellbeteckningar, reservdelsnummer och All uautorisert bruk eller kopiering av innholdet eller en del av det er forbudt.
ritningar. Dette gjelder særlig varemerker, modellbenevnelser, delenumre og tegninger.
Limitation de garantie et de responsabilité
Utiliser uniquement les pièces homologuées.
Tout dommage ou mauvais fonctionnement dû à l’utilisation de pièces non homo- Limitazione di Garanzia e di Responsabilità Takuun ja vastuuvelvollisuuden rajoitus
loguées n’est pas couvert par la garantie ou la responsabilité des produits défectueux. Usare solo componenti autorizzati. Käytä vain valmistajan hyväksymiä varaosia.
Le fabriquant décline toute responsabilité en cas de dommage faisant suite à des mod- Qualsiasi danno o malfunzione causati dall'uso di componenti non autorizzati non è
coperto dalla Garanzia o dalla Responsabilità sul Prodotto. Takuu ja tuotevastuu eivät kata vahinkoja tai toimintahäiriöitä, joiden syynä on mui-
ifications, des ajouts ou des conversions effectués sans l’accord écrit du fabriquant.
Il fabbricante non accetta alcuna reponsabilità per danni derivanti da modifiche, den kuin hyväksyttyjen varaosien käyttö.
Copyright 2012, Atlas Copco Airpower n.v., Antwerp, Belgique. aggiunte o trasformazioni effettuate senza l'approvazione scritta del fabbricante. Valmistaja ei vastaa vahingoista, jotka aiheutuvat ilman valmistajan kirjallista lupaa
Toute utilisation ou copie du contenu, ou d’une parte de celui-ci, non autorisée est tehdyistä muutoksista tai lisäyksistä.
interdite. Copyright 2012, Atlas Copco Airpower n.v., Anversa, Belgio.
Cette interdiction s’applique en particulier aux marques de commerce, aux Sono vietati ogni uso o copia non autorizzati del contenuto o di qualsiasi parte dello
stesso. Copyright 2012, Atlas Copco Airpower n.v., Antwerpen, Belgia.
dénominations des modèles, aux numéros des pièces et aux schémas.
Ciò si applica in particolare ai marchi, alle denominazioni dei modelli, ai numeri dei Sisällön osittainenkin käyttö tai kopiointi ilman lupaa on kielletty.
componenti ed ai disegni Tämä koskee erityisesti tavaramerkkejä, mallien nimiä, osanumeroita ja piirustuksia.
Garantie- und Haftungseinschränkungen
Nur zugelassene Teile verwenden.
Jede Beschädigung oder Fehlfunktion, die durch die Verwendung von nicht zugelass- Garanti- og ansvarsbegrænsning Garantijas un atbildîbas ierobeþojumi
enen Teilen verursacht wurde, ist nicht durch die Garantie oder Produkthaftung abge- Brug kun tilladte reservedele.
deckt. Enhver skade eller fejlfunktion, forårsaget af brug af ikke tilladte reservedele, Izmantot tikai ieteiktâs rezerves daïas.
Der Hersteller übernimmt keine Haftung für Schäden, die durch Modifizierungen, omfattes ikke af garantien eller produktansvaret. Ðî garantija nesedz bojâjumus vai disfunkciju, kuri ir raduðies neatïautu rezerves daïu
Ergänzungen oder Funktionsänderungen entstehen, die ohne schriftliche Zustimmung Fabrikanten kan ikke drages til ansvar for nogen skade som følge af ændringer, izmantoðanas rezultâtâ.
des Herstellers erfolgt sind. udvidelser eller ombygninger, der er blevet udført uden fabrikantens skriftlige sam- Raþotâjs nepieòem pretenzijas par bojâjumiem, kas izriet no modifikâcijâm,
tykke. papildinâjumiem vai pârveidojumiem bez raþotâja rakstiskas piekriðanas.
Urheberrecht 2012, Atlas Copco Airpower n.v., Antwerpen, Belgien.
Jede nicht genehmigte Verwendung oder Kopie des Inhaltes oder von Teilen ist unter- Copyright 2012, Atlas Copco Airpower n.v., Antwerpen, Belgien. Autortiesîbas 2012, Atlas Copco Airpower n.v., Antverpene, Beïìija.
sagt. Enhver uautoriseret brug eller kopiering af indholdet eller dele deraf er forbudt. Jebkura neatïautâ ðî satura izmantoðana vai kopçðana ir aizliegta.Tas konkrçti attiecas
Das bezieht sich im Einzelnen auf Warenzeichen, Modellbezeichnungen, Dette gælder især varemærker, modelbenævnelser, delnumre og tegninger. uz tirdzniecîbas markâm, modeïu denominâcijâm, daïu numuriem un rasçjumiem.
Teilenummern und Zeichnungen
-9-
XAHS 447 Cd - XAHS 950 CD7s
Limites de Garantia e Responsabilidade Autorské práva 2012, Atlas Copco Airpower n.v., Antverpy, Belgicko. Omezení záruky a odpovědnosti
Utilize apenas peças autorizadas. Akékoľvek neoprávnené použitie alebo kopírovanie obsahu, alebo jeho časti
je zakázané. Používejte pouze takové součásti, které jsou schválené výrobcem zařízení.
Avarias ou defeitos de funcionamento que sejam causados pelo uso de sobresselentes Toto sa vzt’ahuje najmä na obchodné značky, modelové označenia, čísla Jakékoliv poškození nebo závady způsobené použitím součástí, které nebyly
ou componentes não autorizados não serão cobertos pela Garantia ou pela Responsa- súčiastok a nákresy. schválené výrobcem zařízení, nejsou kryty zárukou, nebo odpovědností za
výrobek.
bilidade de Produto.
Výrobce nepřijímá žádnou odpovědnost za jakékoliv škody, způsobené
O fabricante não aceita qualquer responsabilidade por quaisquer danos resultantes de Garantii ja piiratud vastutus modifikacemi, doplňky nebo přestavbami zařízení provedenými bez
modificações, adições ou conversões efectuadas sem a aprovação escrita do fabri- Kasutage ainult valmistaja poolt aktsepteeritud varuosi. předchozího písemného svolení.
cante. Mis tahes vigastus või rike, mille on põhjustanud valmistaja poolt aktsepteerimata
varuosa kasutamine, ei kuulu toote garantii või tootja vastutuse alla. Copyright 2012, Atlas Copco Airpower n.v., Antverpy, Belgie.
Valmistaja ei aktsepteeri ühtegi riket, mis on tekkinud toote modifitseerimisest, Jakékoliv neoprávněné použití nebo kopírování obsahu tohoto dokumentu
Copyright 2012, Atlas Copco Airpower n.v., Antuérpia, Bélgica. nebo kterékoliv jeho části je zakázáno.
lisandustest või ümberehitamisest, mida valmistaja ei ole kirjalikult heaks kiitnud.
Qualquer uso não autorizado ou cópia do conteúdo ou de qualquer parte dele é proib- Toto platí obzvláště pro obchodní známky, označení modelů, čísla součástí a
ida. výkresovou dokumentací.
Copyright 2012, Atlas Copco Airpower n.v., Antwerp, Belgium.
Isto aplica-se em particular a marcas registadas, denominações de modelos, números Käesoleva juhendi mistahes loata kasutamine või kopeerimine on keelatud.
de peças e desenhos. See kehtib nii kaubamärkide, mudeli nimetuste, varuosade numbrite kui ka jooniste Garancijski pogoji in omejitve
kohta.
Uporabljajte samo odobrene dele.
有限担保和责任 Garancija proizvajalca ni veljavna pri poškodbah ali motnjah v delovanju, ki so
Ограничение гарантии и ответственности posledica uporabe neodobrenih delov.
只允许使用经认可的零件。 Proizvajalec ne prevzema nikakršne odgovornosti za poškodbe, ki so nastale
Используйте компоненты только авторизованных поставщиков.
因使用未经认可的零件而导致的任何损坏或故障不在本担保或产品责任所保障 Не распространяется гарантия и ответственность за продукцию при zaradi sprememb, dodatkov ali prilagoditev na izdelku, ki so bile izvedene brez
的范围之内。 любых повреждениях или неисправностях в результате использования pisne odobritve proizvajalca.
未经制造商书面许可,制造商概不负责因擅自对设备进行改动、添加附件或改 неавторизованных компонентов.
Производитель не несет никакой ответственности за любые Copyright 2012, Atlas Copco Airpower n.v., Antwerp, Belgium.
型而导致的设备损坏。 Brez pisnega dovoljenja ni dovoljeno uporabljati ali razmnoževati nobenega
повреждения, возникшие в результате модификации, дополнения или
dela dokumenta.
版权 2012,比利时安特卫普 Atlas Copco Airpower n.v.。 изменения, выполненные без письменного утверждения производителя. To velja še posebno za blagovne znamke, označbe modelov, številke izdelkov
in risbe.
未经许可,禁止使用或复制本手册中所含的全部或任何一部分内容。 Copyright 2012, Atlas Copco Airpower n.v., Антверпен, Бельгия.
本公告特别适用于本手册所含的商标、型号名称、零件代号和图纸。 Запрещается любое несанкционированное использование или
копирование содержания этих материалов или их части. Garantijos ir atsakomybës galiojimas
В особенности это относится к торговым маркам, обозначениям моделей,
A garancia és felelősség korlátozása номерам деталей и чертежам. Naudokite tik originalias dalis.
Garantija nebus taikoma tuo atveju, jeigu þala ar sutrikimas atsiranda naudojant
Csak jóváhagyott alkatrészeket használjon! neoriginalias dalis.
A nem jóváhagyott alkatrészek használatából adódó sérülésekre és Gwarancja i ograniczenie odpowiedzialności Gamintojas neprisiima jokios atsakomybës dël þalos, susijusios su modifikacija,
üzemzavarra nem terjed ki a garancia és a termékfelelősség. papildymu ar perdirbimu, atliktu be raðtiðko gamintojo sutikimo.
Stosować jedynie oryginalne części zamienne.
A gyártó semminemű felelősséget nem vállal a gyártó írásos jóváhagyása
Jakiekolwiek uszkodzenia lub niesprawności spowodowane stosowaniem
nélkül végzett bármilyen módosításokból, kiegészítésekből vagy Autorystës teisë 2012, “Atlas Copco Airpower n.v.“, Antverpenas, Belgija.
niezaaprobowanych części zamiennych nie są objęte gwarancją lub
átalakításokból adódó sérülésekért. Neteisëtas viso teksto ar kurios nors jo dalies panaudojimas ar kopijavimas yra
odpowiedzialnością za produkt.
Producent nie będzie ponosił żadnej odpowiedzialności za jakiekolwiek szkody draudþiamas.
Copyright 2012, Atlas Copco Airpower n.v., Antwerp, Belgium. Visø pirma ði sàlyga taikoma prekiniams þenklams, modeliø pavadinimams, daliø
spowodowane modyfikacjami, dodatkami lub zmianami wykonanymi bez
A kézikönyv tartalma vagy annak egy részének engedély nélküli
felhasználása vagy másolása tilos. pisemnej zgody producenta. numeriams ir brëþiniams.
Ez vonatkozik különösen a védjegyekre, a típusjelölésekre, cikkszámokra és
rajzokra. Copyright 2012, Atlas Copco Airpower n.v., Antwerpia, Belgia.
Wszelkie stosowanie lub kopiowanie zawartości lub jakiejkolwiek części
publikacji bez zezwolenia jest zabronione.
Záruka a obmedzenia zodpovednosti výrobcu Dotyczy to szczególnie znaków handlowych, oznaczeń modeli, numerów
części oraz rysunków.
Používajte len schválené súčiastky.
Akákoľvek škoda alebo porucha spôsobená použitím neschválených súčiastok
nie je zahrnutá v záruke ani zodpovednosti výrobcu za škodu.
Výrobca nepripúšt’a žiadnu zodpovednost’ za akékoľvek škody vzniknuté
úpravou, pridaním alebo prerobením, ktoré boli vykonané bez
predchádzajúceho písomného súhlasu výrobcu.
- 10 -
SAFETY PRECAUTIONS FOR PORTABLE COMPRESSOR
To be read attentively and acted accordingly before towing, lifting, operating, performing maintenance or repairing the compressor
0.1 INTRODUCTION eliminate all possible sources of danger at the unit. when air is admitted.
When handling, operating, overhauling and/or performing maintenance or 4 Normal ratings (pressures, temperatures, speeds, etc.) shall be durably
The policy of Atlas Copco is to provide the users of their equipment with repair on Atlas Copco equipment, the mechanics are expected to use safe marked.
safe, reliable and efficient products. Factors taken into account are among engineering practices and to observe all relevant local safety requirements
5 Operate the unit only for the intended purpose and within its rated
others: and ordinances. The following list is a reminder of special safety directives
limits (pressure, temperature, speeds, etc.).
- the intended and predictable future use of the products, and the and precautions mainly applicable to Atlas Copco equipment.
environments in which they are expected to operate, 6 The machinery and equipment shall be kept clean, i.e. as free as
These safety precautions apply to machinery processing or consuming air. possible from oil, dust or other deposits.
- applicable rules, codes and regulations, Processing of any other gas requires additional safety precautions typical to
- the expected useful product life, assuming proper service and the application and are not included herein. 7 To prevent an increase in working temperature, inspect and clean heat
maintenance, transfer surfaces (cooler fins, intercoolers, water jackets, etc.)
- providing the manual with up-to-date information. Neglecting the safety precautions may endanger people as well as
regularly. See the maintenance schedule.
environment and machinery:
Before handling any product, take time to read the relevant instruction - endanger people due to electrical, mechanical or chemical influences, 8 All regulating and safety devices shall be maintained with due care to
manual. Besides giving detailed operating instructions, it also gives - endanger the environment due to leakage of oil, solvents or other ensure that they function properly. They may not be put out of action.
specific information about safety, preventive maintenance, etc. substances,
Keep the manual always at the unit location, easy accessible to the 9 Care shall be taken to avoid damage to safety valves and other
- endanger the machinery due to function failures. pressure-relief devices, especially to avoid plugging by paint, oil coke
operating personnel.
All responsibility for any damage or injury resulting from neglecting these or dirt accumulation, which could interfere with the functioning of the
See also the safety precautions of the engine and possible other equipment, precautions or by non-observance of ordinary caution and due care device.
which are separately sent along or are mentioned on the equipment or parts required in handling, operating, maintenance or repair, also if not expressly
of the unit. 10 Pressure and temperature gauges shall be checked regularly with
mentioned in this instruction manual, is disclaimed by Atlas Copco. regard to their accuracy. They shall be replaced whenever outside
These safety precautions are general and some statements will therefore not The manufacturer does not accept any liability for any damage arising from acceptable tolerances.
always apply to a particular unit. the use of non-original parts and for modifications, additions or 11 Safety devices shall be tested as described in the maintenance schedule
Only people that have the right skills should be allowed to operate, adjust, conversions made without the manufacturer’s approval in writing. of the instruction manual to determine that they are in good operating
perform maintenance or repair on Atlas Copco equipment. It is the If any statement in this manual does not comply with local legislation, the condition.
responsibility of management to appoint operators with the appropriate stricter of the two shall be applied.
training and skill for each category of job. 12 Mind the markings and information labels on the unit.
Statements in these safety precautions should not be interpreted as 13 In the event the safety labels are damaged or destroyed, they must be
Skill level 1: Operator suggestions, recommendations or inducements that it should be used in replaced to ensure operator safety.
An operator is trained in all aspects of operating the unit with the push- violation of any applicable laws or regulations.
buttons, and is trained to know the safety aspects. 14 Keep the work area neet. Lack of order will increase the risk of
accidents.
Skill level 2: Mechanical technician
A mechanical technician is trained to operate the unit the same as the 15 When working on the unit, wear safety clothing. Depending on the
operator. In addition, the mechanical technician is also trained to perform 0.2 GENERAL SAFETY PRECAUTIONS kind of activities these are: safety glasses, ear protection, safety helmet
maintenance and repair, as described in the instruction manual, and is (including visor), safety gloves, protective clothing, safety shoes. Do
allowed to change settings of the control and safety system. A mechanical not wear the hair long and loose (protect long hair with a hairnet), or
1 The owner is responsible for maintaining the unit in a safe operating wear loose clothing or jewelry.
technician does not work on live electrical components. condition. Unit parts and accessories must be replaced if missing or
Skill level 3: Electrical technician unsuitable for safe operation. 16 Take precautions against fire. Handle fuel, oil and anti-freeze with care
because they are inflammable substances. Do not smoke or approach
An electrical technician is trained and has the same qualifications as both 2 The supervisor, or the responsible person, shall at all times make sure with naked flame when handling such substances. Keep a fire-
the operator and the mechanical technician. In addition, the electrical that all instructions regarding machinery and equipment operation and extinguisher in the vicinity.
technician may carry out electrical repairs within the various enclosures of maintenance are strictly followed and that the machines with all
the unit. This includes work on live electrical components. accessories and safety devices, as well as the consuming devices, are
Skill level 4: Specialist from the manufacturer in good repair, free of abnormal wear or abuse, and are not tampered
with.
This is a skilled specialist sent by the manufacturer or its agent to perform
complex repairs or modifications to the equipment. 3 Whenever there is an indication or any suspicion that an internal part
of a machine is overheated, the machine shall be stopped but no
In general it is recommended that not more than two people operate the
inspection covers shall be opened before sufficient cooling time has
unit, more operators could lead to unsafe operating conditions. Take
elapsed; this to avoid the risk of spontaneous ignition of oil vapour
necessary steps to keep unauthorized persons away from the unit and
- 11 -
0.3 SAFETY DURING TRANSPORT AND members shall be applied as near to perpendicular as possible. If injury or death. For breathing air quality, the compressed air must be
required, a lifting beam shall be applied between hoist and load. adequately purified according to local legislation and standards.
INSTALLATION Breathing air must always be supplied at stable, suitable pressure.
9 Never leave a load hanging on a hoist.
9 Distribution pipework and air hoses must be of correct diameter and
To lift a unit, all loose or pivoting parts, e.g. doors and towbar, shall first be 10 A hoist has to be installed in such a way that the object will be lifted
suitable for the working pressure. Never use frayed, damaged or
securely fastened. perpendicular. If that is not possible, the necessary precautions must be
deteriorated hoses. Replace hoses and flexibles before the lifetime
taken to prevent load-swinging, e.g. by using two hoists, each at
Do not attach cables, chains or ropes directly to the lifting eye; apply a expires. Use only the correct type and size of hose end fittings and
approximately the same angle not exceeding 30° from the vertical.
crane hook or lifting shackle meeting local safety regulations. Never allow connections.
sharp bends in lifting cables, chains or ropes. 11 Locate the unit away from walls. Take all precautions to ensure that
hot air exhausted from the engine and driven machine cooling systems 10 If the compressor is to be used for sand-blasting or will be connected
Helicopter lifting is not allowed. cannot be recirculated. If such hot air is taken in by the engine or to a common compressed-air system, fit an appropriate non-return
It is strictly forbidden to dwell or stay in the risk zone under a lifted load. driven machine cooling fan, this may cause overheating of the unit; if valve (check valve) between compressor outlet and the connected
Never lift the unit over people or residential areas. Lifting acceleration and taken in for combustion, the engine power will be reduced. sand-blasting or compressed-air system. Observe the right mounting
retardation shall be kept within safe limits. position/direction.
1 Before towing the unit: 11 Before removing the oil filler plug, ensure that the pressure is released
- ascertain that the pressure vessel(s) is (are) depressurized, by opening an air outlet valve.
- check the towbar, the brake system and the towing eye. Also check
the coupling of the towing vehicle,
0.4 SAFETY DURING USE AND OPERATION 12 Never remove a filler cap of the cooling water system of a hot engine.
Wait until the engine has sufficiently cooled down.
- check the towing and brake capability of the towing vehicle,
- check that the towbar, jockey wheel or stand leg is safely locked in 1 When the unit has to operate in a fire-hazardous environment, each 13 Never refill fuel while the unit is running, unless otherwise stated in
the raised position, engine exhaust has to be provided with a spark arrestor to trap the Atlas Copco Instruction Book (AIB). Keep fuel away from hot
- ascertain that the towing eye can swivel freely on the hook, incendiary sparks. parts such as air outlet pipes or the engine exhaust. Do not smoke
- check that the wheels are secure and that the tyres are in good when fuelling. When fuelling from an automatic pump, an earthing
2 The exhaust contains carbon monoxide which is a lethal gas. When the cable should be connected to the unit to discharge static electricity.
condition and inflated correctly, unit is used in a confined space, conduct the engine exhaust to the
- connect the signalisation cable, check all lights and connect the Never spill nor leave oil, fuel, coolant or cleansing agent in or around
outside atmosphere by a pipe of sufficient diameter; do this in such a the unit.
pneumatic brake couplers, way that no extra back pressure is created for the engine. If necessary,
- attach the safety break-away cable or safety chain to the towing install an extractor. Observe any existing local regulations. Make sure 14 All doors shall be shut during operation so as not to disturb the cooling
vehicle, that the unit has sufficient air intake for operation. If necessary, install air flow inside the bodywork and/or render the silencing less effective.
- remove wheel chocks, if applied, and disengage the parking brake. extra air intake ducts. A door should be kept open for a short period only e.g. for inspection
2 To tow a unit use a towing vehicle of ample capacity. Refer to the or adjustment.
3 When operating in a dust-laden atmosphere, place the unit so that dust
documentation of the towing vehicle. is not carried towards it by the wind. Operation in clean surroundings 15 Periodically carry out maintenance works according to the
3 If the unit is to be backed up by the towing vehicle, disengage the considerably extends the intervals for cleaning the air intake filters and maintenance schedule.
overrun brake mechanism (if it is not an automatic mechanism). the cores of the coolers. 16 Stationary housing guards are provided on all rotating or reciprocating
4 Never exceed the maximum towing speed of the unit (mind the local 4 Close the compressor air outlet valve before connecting or parts not otherwise protected and which may be hazardous to
regulations). disconnecting a hose. Ascertain that a hose is fully depressurized personnel. Machinery shall never be put into operation, when such
before disconnecting it. Before blowing compressed air through a hose guards have been removed, before the guards are securely reinstalled.
5 Place the unit on level ground and apply the parking brake before or air line, ensure that the open end is held securely, so that it cannot
disconnecting the unit from the towing vehicle. Unclip the safety whip and cause injury.
break-away cable or safety chain. If the unit has no parking brake or
jockey wheel, immobilize the unit by placing chocks in front of and/or 5 The air line end connected to the outlet valve must be safeguarded with
behind the wheels. When the towbar can be positioned vertically, the a safety cable, attached next to the valve.
locking device must be applied and kept in good order. 6 No external force may be exerted on the air outlet valves, e.g. by
6 To lift heavy parts, a hoist of ample capacity, tested and approved pulling on hoses or by installing auxiliary equipment directly to a
according to local safety regulations, shall be used. valve, e.g. a water separator, a lubricator, etc. Do not step on the air
outlet valves.
7 Lifting hooks, eyes, shackles, etc., shall never be bent and shall only
have stress in line with their design load axis. The capacity of a lifting 7 Never move a unit when external lines or hoses are connected to the
device diminishes when the lifting force is applied at an angle to its outlet valves, to avoid damage to valves, manifold and hoses.
load axis. 8 Do not use compressed air from any type of compressor, without
8 For maximum safety and efficiency of the lifting apparatus all lifting taking extra measures, for breathing purposes as this may result in
- 12 -
17 Noise, even at reasonable levels, can cause irritation and disturbance 26 Never operate the unit at pressures or speeds below or in excess of its 12 Support the towbar and the axle(s) securely if working underneath the
which, over a long period of time, may cause severe injuries to the limits as indicated in the technical specifications. unit or when removing a wheel. Do not rely on jacks.
nervous system of human beings.
13 Do not remove any of, or tamper with, the sound-damping material.
When the sound pressure level, at any point where personnel normally
Keep the material free of dirt and liquids such as fuel, oil and cleansing
has to attend, is:
agents. If any sound-damping material is damaged, replace it to
below 70 dB(A): no action needs to be taken,
above 70 dB(A): noise-protective devices should be provided for 0.5 SAFETY DURING MAINTENANCE AND REPAIR prevent the sound pressure level from increasing.
people continuously being present in the room, 14 Use only lubricating oils and greases recommended or approved by
below 85 dB(A): no action needs to be taken for occasional visitors Maintenance, overhaul and repair work shall only be carried out by Atlas Copco or the machine manufacturer. Ascertain that the selected
staying a limited time only, adequately trained personnel; if required, under supervision of someone lubricants comply with all applicable safety regulations, especially
above 85 dB(A): room to be classified as a noise-hazardous area and qualified for the job. with regard to explosion or fire-risk and the possibility of
an obvious warning shall be placed permanently at decomposition or generation of hazardous gases. Never mix synthetic
1 Use only the correct tools for maintenance and repair work, and only with mineral oil.
each entrance to alert people entering the room, for
tools which are in good condition.
even relatively short times, about the need to wear 15 Protect the engine, alternator, air intake filter, electrical and regulating
ear protectors, 2 Parts shall only be replaced by genuine Atlas Copco replacement parts. components, etc., to prevent moisture ingress, e.g. when steam-
above 95 dB(A): the warning(s) at the entrance(s) shall be 3 All maintenance work, other than routine attention, shall only be cleaning.
completed with the recommendation that also undertaken when the unit is stopped. Steps shall be taken to prevent
occasional visitors shall wear ear protectors, 16 When performing any operation involving heat, flames or sparks on a
inadvertent starting. In addition, a warning sign bearing a legend such machine, the surrounding components shall first be screened with non-
above 105 dB(A): special ear protectors that are adequate for this as ”work in progress; do not start” shall be attached to the starting
noise level and the spectral composition of the flammable material.
equipment.
noise shall be provided and a special warning to On engine-driven units the battery shall be disconnected and removed 17 Never use a light source with open flame for inspecting the interior of
that effect shall be placed at each entrance. or the terminals covered by insulating caps. a machine.
18 Insulation or safety guards of parts the temperature of which can be in On electrically driven units the main switch shall be locked in open 18 When repair has been completed, the machine shall be barred over at
excess of 80 °C (175 °F) and which may be accidentally touched by position and the fuses shall be taken out. A warning sign bearing a least one revolution for reciprocating machines, several revolutions for
personnel shall not be removed before the parts have cooled to room legend such as ”work in progress; do not supply voltage” shall be rotary ones to ensure that there is no mechanical interference within
temperature. attached to the fuse box or main switch. the machine or driver. Check the direction of rotation of electric
19 Never operate the unit in surroundings where there is a possibility of 4 Before dismantling any pressurized component, the compressor or motors when starting up the machine initially and after any alteration
taking in flammable or toxic fumes. equipment shall be effectively isolated from all sources of pressure and to the electrical connection(s) or switch gear, to check that the oil
the entire system shall be relieved of pressure. Do not rely on non- pump and the fan function properly.
20 If the working process produces fumes, dust or vibration hazards, etc.,
return valves (check valves) to isolate pressure systems. In addition, a 19 Maintenance and repair work should be recorded in an operator’s
take the necessary steps to eliminate the risk of personnel injury.
warning sign bearing a legend such as ”work in progress; do not open” logbook for all machinery. Frequency and nature of repairs can reveal
21 When using compressed air or inert gas to clean down equipment, do shall be attached to each of the outlet valves. unsafe conditions.
so with caution and use the appropriate protection, at least safety
5 Prior to stripping an engine or other machine or undertaking major 20 When hot parts have to be handled, e.g. shrink fitting, special heat-
glasses, for the operator as well as for any bystander. Do not apply
overhaul on it, prevent all movable parts from rolling over or moving. resistant gloves shall be used and, if required, other body protection
compressed air or inert gas to your skin or direct an air or gas stream at
people. Never use it to clean dirt from your clothes. 6 Make sure that no tools, loose parts or rags are left in or on the shall be applied.
machine. Never leave rags or loose clothing near the engine air intake. 21 When using cartridge type breathing filter equipment, ascertain that
22 When washing parts in or with a cleaning solvent, provide the required
ventilation and use appropriate protection such as a breathing filter, 7 Never use flammable solvents for cleaning (fire-risk). the correct type of cartridge is used and that its useful service life is not
safety glasses, rubber apron and gloves, etc. surpassed.
8 Take safety precautions against toxic vapours of cleaning liquids.
23 Safety shoes should be compulsory in any workshop and if there is a 22 Make sure that oil, solvents and other substances likely to pollute the
9 Never use machine parts as a climbing aid. environment are properly disposed of.
risk, however small, of falling objects, wearing of a safety helmet
should be included. 10 Observe scrupulous cleanliness during maintenance and repair. Keep 23 Before clearing the unit for use after maintenance or overhaul, check
away dirt, cover the parts and exposed openings with a clean cloth, that operating pressures, temperatures and speeds are correct and that
24 If there is a risk of inhaling hazardous gases, fumes or dust, the paper or tape.
respiratory organs must be protected and depending on the nature of the control and shutdown devices function correctly.
the hazard, so must the eyes and skin. 11 Never weld on or perform any operation involving heat near the fuel or
oil systems. Fuel and oil tanks must be completely purged, e.g. by
25 Remember that where there is visible dust, the finer, invisible particles steam-cleaning, before carrying out such operations. Never weld on, or
will almost certainly be present too; but the fact that no dust can be in any way modify, pressure vessels. Disconnect the alternator cables
seen is not a reliable indication that dangerous, invisible dust is not during arc welding on the unit.
present in the air.
- 13 -
0.6 TOOL APPLICATIONS SAFETY - the capacity of the vessel V in l.
2 The pressure vessel is only to be used for the applications as specified
Apply the proper tool for each job. With the knowledge of correct tool use above and in accordance with the technical specifications. Safety
and knowing the limitations of tools, along with some common sense, reasons prohibit any other applications.
many accidents can be prevented. 3 National legislation requirements with respect to re-inspection must be
Special service tools are available for specific jobs and should be used complied with.
when recommended. The use of these tools will save time and prevent 4 No welding or heat treatment of any kind is permitted to those vessel
damage to parts. walls which are exposed to pressure.
5 The vessel is provided and may only be used with the required safety
equipment such as manometer, overpressure control devices, safety
valve, etc.
0.7 SPECIFIC SAFETY PRECAUTIONS 6 Draining of condensate shall be performed regularly when vessel is in
use.
Batteries
7 Installation, design and connections should not be changed.
When servicing batteries, always wear protecting clothing and glasses.
8 Bolts of cover and flanges may not be used for extra fixation.
1 The electrolyte in batteries is a sulphuric acid solution which is fatal if
it hits your eyes, and which can cause burns if it contacts your skin.
Therefore, be careful when handling batteries, e.g. when checking the Safety valves
charge condition.
All adjustments or repairs are to be done by an authorized representative of
2 Install a sign prohibiting fire, open flame and smoking at the post the valve supplier (see maintenance schedule).
where batteries are being charged.
3 When batteries are being charged, an explosive gas mixture forms in
the cells and might escape through the vent holes in the plugs.
Thus an explosive atmosphere may form around the battery if
ventilation is poor, and can remain in and around the battery for
several hours after it has been charged. Therefore:
- never smoke near batteries being, or having recently been, charged,
- never break live circuits at battery terminals, because a spark
usually occurs.
4 When connecting an auxiliary battery (AB) in parallel to the unit
battery (CB) with booster cables: connect the + pole of AB to the +
pole of CB, then connect the - pole of CB to the mass of the unit.
Disconnect in the reverse order.
Pressure vessels
(according to directive 87/404/EEC annex II § 2)
Maintenance/installation requirements:
1 The vessel can be used as pressure vessel or as separator and is
designed to hold compressed air for the following application:
- pressure vessel for compressor,
- medium AIR/OIL,
and operates as detailed on the data plate of the vessel:
- the maximum working pressure ps in bar,
- the maximum working temperature Tmax in °C,
- the minimum working temperature Tmin in °C,
- 14 -
ORDERING SPARE PARTS
- 15 -
ORDERING SPARE PARTS
- 16 -
ORDERING SPARE PARTS
- 17 -
ORDERING SPARE PARTS
- 18 -
SERVICE PAK
- 19 -
ENGINE OIL - PAROIL E
- 20 -
ENGINE OIL - PAROIL E XTRA
- 21 -
COMPRESSOR OIL - PAROIL M
- 22 -
COMPRESSOR OIL - PAROIL S
- 23 -
ENGINE COOLANT - PARCOOL EG
- 24 -
SERVICE KIT - UNLOADING VALVE
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 74 or 75 or 76
See Page 77
See Page 73
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 86 or 88
20 1604 7682 03 PIPE RADIATOR 1
30 1604 5868 00 HOSE 1
40 0347 6100 20 HOSE CLAMP 2
100 1604 7465 03 PIPE RADIATOR 1
110 1604 1280 01 HOSE 1
120 0347 6100 19 HOSE CLAMP 2
210 1604 5175 01 HOSE 1
220 0347 6100 21 HOSE CLAMP 3
250 1604 3785 03 PIPE IC 1
260 1604 2114 02 HOSE IC 1
270 0347 6100 21 HOSE CLAMP 4
300 0571 0020 40 HOSE NIPPLE 1
305 0071 8403 01 FUEL HOSE AR
306 0347 6106 00 HOSE CLAMP 2
See Page 57 or 211 310 0571 0020 41 HOSE NIPPLE 1
315 5500 5091 00 BUSHING 1
350 1604 4763 01 SUPPORT 1
352 0301 2378 00 PLAIN WASHER 1
355 0147 1474 03 HEX. HEAD SCREW 1
370 1619 2861 05 PIPE CLAMP 1
380 0147 1326 03 HEX. HEAD SCREW 1
385 0333 3227 00 LOCK WASHER 1
390 0266 2110 00 HEXAGON NUT 1
See Page 86 or 88
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 31
See Page 44
See Page 50
See Page 49
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
20 0975 8300 16 BATTERY 2 412 1089 0584 01 SWITCH 1 635 1089 9562 08 STRAP 1
22 1604 7881 00 COVER 2 413 1626 2731 01 BRACKET 1 640 1088 0019 02 WASHER 1
40 1615 4861 00 CLAMP 4 415 1615 5664 00 SCREW 4 660 1626 5539 00 GUIDE 1
45 1619 5337 01 BOLT 8 416 1626 5492 01 GUIDE 1 662 0346 2900 12 CLAMP 2
55 0147 1360 03 SCREW 1 417 1626 5493 02 GUIDE 1 665 0346 2900 12 CLAMP 2
60 1604 0383 00 SEAL 2 418 1626 5494 01 GUIDE 1 670 0266 2110 00 NUT 4
65 1088 0019 02 WASHER 2 419 1626 5495 01 GUIDE 1 675 0301 2335 00 WASHER 4
130 1626 5744 00 CABLE 1 420 1626 5517 80 ASSEMBLY 1 680 0346 1002 41 CLAMP 3
132 1626 5748 00 CABLE 1 A10 1626 5517 00 BOX 1 685 0147 1323 03 SCREW 1
135 1604 6019 00 CABLE 1 421 1619 5898 01 SCREW 10 690 0266 2110 00 NUT 1
136 1626 5749 00 CABLE 1 422 0346 1002 05 PIPE 6 695 0301 2335 00 WASHER 1
137 1626 5746 02 CABLE 1 423 0346 1002 07 CLAMP 3 700 0348 0101 05 STRIP 100
140 1604 8147 05 CABLE 1 424 1619 5898 01 SCREW 9
141 1619 3729 00 CAP 1 426 1089 9206 09 CIRCUIT BREAK 5
142 0147 1323 03 SCREW 5 427 1089 9530 04 CIRCUIT BREAK. 1
143 0301 2335 00 WASHER 5 428 1626 5524 00 WIRING 1
155 1604 3746 10 WIRE HARNESS 1 429 0147 1323 03 SCREW 2
160 1089 0574 70 SENSOR 1 430 1089 9385 02 ISOLATOR 2
195 1089 9579 80 SENSOR 1 431 0301 2335 00 WASHER 2
250 1089 9457 24 CONNECTOR 1 435 0147 1326 03 SCREW 2
251 1089 9457 81 CONNECTOR 2 440 0333 3227 00 LOCK 2
260 1604 3791 02 CABLE 1 445 0301 2335 00 WASHER 2
281 1604 3679 00 SEAL 1 450 1604 2121 01 STRIP 1
285 5541 9781 00 HEX HEAD 4 455 0147 1323 03 SCREW 2
290 0301 2321 00 WASHER 4 460 0333 3227 00 LOCK 2
295 1604 4353 00 KIT 4 480 0147 1358 03 BOLT 1
300 1604 9671 00 RELAY 1 485 1088 0019 02 WASHER 1
301 1626 5563 01 CABLE 2 490 1604 2121 01 STRIP 1
302 0147 1247 03 SCREW 2 492 0324 1000 16 SLEEVE 2
303 1604 9749 02 CABLE 1 493 0266 2110 00 NUT 2
304 0301 2321 00 WASHER 2 495 1619 5337 03 BOLT 2
305 0266 2108 00 NUT 2 500 0333 3227 00 LOCK 2
325 1626 5512 81 CONTROL PANEL 1 550 1089 0620 21 VALVE 1
(For details see page 129) 555 0653 1124 00 GASKET 1
380 1626 5482 01 GUIDE 1 560 0580 0525 06 COUPLING 1
382 1615 5664 00 SCREW 2 565 0580 0500 26 ADAPTER 1
393 1626 5496 01 BRACKET 1 570 0653 1124 00 GASKET 1
394 1613 0801 02 CLAMP 1 575 9090 0510 00 SILENCER 1
395 0147 1247 03 SCREW 1 580 0653 1124 00 GASKET 1
396 0301 2321 00 WASHER 1 620 1089 9562 03 STRAP 1
410 1626 5481 02 SUPPORT 1 625 1088 0019 03 KIT 1
411 1626 5480 02 BRACKET 1 630 0147 1398 03 SCREW 1
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 44
See Page 44
See Page 86 or 88
See Page 42
See Page 64
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 31
See Page 83
See Page 83
See Page 73
See Page 79 or 82 or 190 or 192
1611 8163 67_ed01
See Page 83 or 194 or 196 or 200 or 204
See Page 83
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 90 or 91 or 93
See Page 50
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 58
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 31
See Page 31
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 40
See Page 40
See Page 40
See Page 40
See Page 40
See Page 73
See Page 40
See Page 58
See Page 58
See Page 90 or 91 or 93 or 237 See Page 40
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
20 1079 5840 15 FITTING 1 232 1604 3383 00 NIPPLE 1 532 1604 3383 00 NIPPLE 1
22 0661 1033 00 SEAL 1 235 0661 1038 00 SEAL 1 535 0661 1038 00 SEAL 1
25 1604 9389 00 HOSE 1 237 0661 1038 00 SEAL 1 540 0661 1038 00 SEAL 1
32 0070 4022 60 CONDUIT AR 238 0686 3716 35 PLUG 1 545 0686 3716 35 PLUG 1
33 1604 8278 01 PIPE 1 240 1088 0832 04 CLAMP 2
34 1088 1501 11 HOSE AR 245 0129 3110 00 RIVET 2
35 0571 0035 53 FITTING 1 300 0653 1124 00 GASKET 1
36 1088 0832 07 CLAMP 2 305 0603 5110 00 FITTING 1
37 0129 3110 00 RIVET 2 306 1619 6153 05 VALVE 1
40 1619 6153 05 VALVE 1 307 0571 0035 36 FITTING 1
45 0571 0035 52 FITTING 1 310 1604 8368 00 HOSE 1
48 1604 3383 00 NIPPLE 1 311 1604 8277 00 PIPE 1
50 0661 1038 00 SEAL 1 312 1088 0832 07 CLAMP 2
55 0661 1038 00 SEAL 1 313 0129 3110 00 RIVET 2
60 0686 3716 35 PLUG 1 315 1088 1501 10 HOSE AR
75 0346 1003 14 CLAMP 1 320 0571 0035 53 FITTING 1
80 1604 4330 00 BRACKET 1 325 1619 6153 05 VALVE 1
85 0147 1319 03 SCREW 1 330 0571 0035 52 FITTING 1
90 0147 1326 03 SCREW 1 332 1604 3383 00 NIPPLE 1
92 0333 3227 00 LOCK 1 335 0661 1038 00 SEAL 1
95 0261 1110 00 NUT 1 340 0661 1038 00 SEAL 1
100 0653 1100 00 GASKET 2 345 0686 3716 35 PLUG 1
106 1604 1793 03 NIPPLE 1 400 - FLAT GASKET 1
107 0663 2108 90 O-RING 1 (Part of service kit, see page 28)
110 1604 9441 00 HOSE 1 405 1079 5840 15 FITTING 1
111 1604 9526 00 PIPE 1 410 0574 8235 24 FLEXIBLE 1
112 1088 0832 07 CLAMP 2 415 1088 1501 10 HOSE AR
113 0129 3110 00 RIVET 2 420 0571 0035 36 FITTING 1
120 0571 0035 53 FITTING 1 425 1619 6153 05 VALVE 1
125 1619 6153 05 VALVE 1 430 0571 0035 52 FITTING 1
130 0571 0035 52 FITTING 1 432 1604 3383 00 NIPPLE 1
132 1604 3383 00 NIPPLE 1 435 0661 1038 00 SEAL 1
135 0661 1038 00 SEAL 1 440 0661 1038 00 SEAL 1
140 0661 1038 00 SEAL 1 445 0686 3716 35 PLUG 1
145 0686 3716 35 PLUG 1 500 1604 9469 01 HOSE 1
200 1604 9471 00 HOSE 1 505 0627 5100 05 SCREW 1
205 0627 5100 05 SCREW 1 510 - SEAL 2
210 0653 1124 00 GASKET 2 (Part of service kit, see page 28)
215 1088 1501 10 HOSE AR 515 1088 1501 10 HOSE AR
220 0571 0035 36 FITTING 1 520 0571 0035 36 FITTING 1
225 1619 6153 05 VALVE 1 525 1619 6153 05 VALVE 1
230 0571 0035 52 FITTING 1 530 0571 0035 52 FITTING 1
See Page 43
See Page 40
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 43
See Page 40
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 62
See Page 31
See Page 62
See Page 31
See Page 62
See Page 31
See Page 62
See Page 31
See Page 78
PANEL ASSEMBLY
- 1604 2542 82 PANEL ASSY (From page 79, 82)
20 1604 2542 02 PANEL 1
30 - INSULATION SILENCING
FOAM (30 mm) 1
PANEL ASSEMBLY
- 1604 2543 83 PANEL ASSY (From page 46)
20 1604 2543 03 PANEL 1
25 - SILENCING FOAM (30 mm) 1
- 114 -
PANEL ASSEMBLY - STANDARD
See Page 34 or 36 or 38
See Page 34 or 36 or 38
DOOR ASSEMBLY
- 1604 2513 84 DOOR ASSY (From page 110,119)
20 1604 2513 04 DOOR 1
25 - SILENCING FOAM (50 mm) 1
30 1619 1663 01 DOOR HOOK 2
35 0129 3270 17 BLIND RIVET 4
50 1615 7884 00 CLIP 3
DOOR ASSEMBLY
- 1604 2515 84 DOOR ASSY (From page 110,119)
20 1604 2515 04 DOOR 1
See Page 110 or 119 25 - SILENCING FOAM (50 mm) 1
30 1619 1663 01 DOOR HOOK 2
35 0129 3270 17 BLIND RIVET 8
50 1615 7884 00 CLIP 2
- 131 -
PRESSURE VESSEL ASSEMBLY - FOR COMPRESSOR WITHOUT COLD WEATHER EQUIPMENTS FOR EC - STANDARD
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
- 1604 7687 81 COOLER ASSEMBLY (From page 117) 210 1626 5913 80 PANEL ASSY 1 560 1604 7685 00 PLATE 1
20 1604 7687 85 SUPPORT ASSY 1 (For details see page 148) 565 1615 5664 00 HEX. HEAD SCREW 3
(For details see page 150) 220 1604 2670 82 PLATE ASSY 1 600 1619 5562 00 SEAL AR
30 1604 7689 00 PAD 1 (For details see page 145)
40 1604 2680 02 OILCOOLER 1 221 - SILENCING FOAM (50 mm) 1
50 0196 1362 00 SET SCREW 2 223 1615 7884 00 CLIP 6
- 1079 0003 33 SILENCING FOAM
60 1604 2676 04 RADIATOR 1 225 1615 5664 00 HEX. HEAD SCREW 12
2000 mm x 1500 mm x 50 mm
65 0196 1362 00 SET SCREW 2 260 1604 2707 81 PLATE ASSY 2
70 0075 4005 70 RUBBER TUBE AR (For details see page 147)
75 0347 6110 00 HOSE CLAMP 2 261 - SILENCING FOAM (50 mm) 2
81 0571 0035 70 FITTING 1 265 0147 1326 03 HEX. HEAD SCREW 6
83 1604 7688 01 EXTENSION 1 267 0301 2335 00 PLAIN WASHER 6
85 1089 0659 63 SWITCH LEVEL 2 270 0291 1110 00 LOCKNUT 6
86 0661 1023 00 SEALING WASHER 2 275 1615 5664 00 HEX. HEAD SCREW 6
87 1615 9329 00 NIPPLE 2 300 1604 2643 01 GUARD 2
90 1604 2812 03 WIRING 1 310 1615 5664 00 HEX. HEAD SCREW 8
91 1088 0801 28 GROMMET 1 350 0147 1323 03 HEX. HEAD SCREW 2
92 0129 3117 00 BLIND RIVET 4 355 0301 2335 00 PLAIN WASHER 2
94 1088 1301 02 CABLE STRIP 5 360 0291 1110 00 LOCKNUT 2
96 1626 1266 00 CLAMP HOSE 4 380 1604 2706 02 PLATE 1
98 1088 1301 02 CABLE STRIP 4 382 1604 2666 02 PLATE 1
100 1604 2499 02 INTERCOOLER 1 383 1202 5211 00 SEAL AR
105 0196 1362 00 SET SCREW 2 384 1604 2668 04 PLATE 1
113 1604 2496 00 GROMMET 1 386 1088 0801 33 GROMMET 1
114 1088 0801 40 GROMMET 1 390 1615 5664 00 HEX. HEAD SCREW 11
115 1604 2672 83 BEAM ASSY 1 440 1604 7548 00 PIPE 2
(For details see page 146) 445 1615 5664 00 HEX. HEAD SCREW 4
120 1604 7686 80 BEAM ASSY 1 450 2252 6291 01 HOSE 4
(For details see page 149) 455 0347 6100 21 HOSE CLAMP 8
130 0147 1362 03 HEX. HEAD SCREW 6 460 1604 2786 03 HOSE IC 2
140 0301 2344 00 PLAIN WASHER 6 461 1604 2785 03 HOSE IC 2
145 1615 5664 00 HEX. HEAD SCREW 3 465 0347 6100 23 HOSE CLAMP 14
150 1604 2504 81 PLATE ASSY 1 470 1604 2769 02 PIPE IC 2
(For details see page 144) 480 1604 7568 00 PIPE 1
155 1615 5664 00 HEX. HEAD SCREW 9 485 1604 7553 00 PIPE 1
170 1604 2503 81 PLATE ASSY 1 490 0663 3131 00 O-RING 2
(For details see page 143) 495 0246 1956 42 STUD 4
175 1615 5664 00 HEX. HEAD SCREW 9 500 0301 2344 00 PLAIN WASHER 4
190 1604 9892 81 COWL ASSY 1 505 0266 2111 00 HEXAGON NUT 4
(For details see page 151) 520 1604 2771 01 PLATE 2
195 1615 5664 00 HEX. HEAD SCREW 8 530 1615 5664 00 HEX. HEAD SCREW 4
535 1604 2496 00 GROMMET 2
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
- 1604 9702 81 COOLER ASSEMBLY (From page 124) 270 0291 1110 00 LOCKNUT 6
20 1626 5797 00 SUPPORT 1 275 1615 5664 00 HEX. HEAD SCREW 6
30 1604 7689 00 PAD 1 300 1604 2643 01 GUARD 2
40 1604 2680 02 OILCOOLER 1 310 1615 5664 00 HEX. HEAD SCREW 8
50 0196 1362 00 SET SCREW 2 350 0147 1323 03 HEX. HEAD SCREW 2
60 1604 2676 04 RADIATOR 1 355 0301 2335 00 PLAIN WASHER 2
65 0196 1362 00 SET SCREW 2 360 0291 1110 00 LOCKNUT 2
70 0075 4005 70 RUBBER TUBE AR 380 1604 2706 02 PLATE 1
75 0347 6110 00 HOSE CLAMP 2 382 1604 2666 02 PLATE 1
81 0571 0035 70 FITTING 1 383 1202 5211 00 SEAL AR
83 1604 7688 01 EXTENSION 1 384 1604 2668 04 PLATE 1
85 1089 0659 63 SWITCH LEVEL 2 385 1088 0803 25 GROMMET 1
86 0661 1023 00 SEALING WASHER 2 386 1088 0801 33 GROMMET 1
87 1615 9329 00 NIPPLE 2 390 1615 5664 00 HEX. HEAD SCREW 11
90 1604 2812 03 WIRING 1 440 1604 7548 00 PIPE 2
91 1088 0801 28 GROMMET 1 445 1615 5664 00 HEX. HEAD SCREW 4
92 0129 3117 00 BLIND RIVET 4 450 2252 6291 01 HOSE 4
94 1088 1301 02 CABLE STRIP 5 455 0347 6100 21 HOSE CLAMP 8
96 1626 1266 00 CLAMP HOSE 4 460 1604 2786 03 HOSE IC 2
98 1088 1301 02 CABLE STRIP 4 461 1604 2785 03 HOSE IC 2
100 1604 2499 02 INTERCOOLER 1 465 0347 6100 23 HOSE CLAMP 14
105 0196 1362 00 SET SCREW 2 470 1604 2769 02 PIPE IC 2
113 1604 2496 00 GROMMET 1 480 1604 7568 00 PIPE 1
114 1088 0801 40 GROMMET 1 485 1604 7553 00 PIPE 1
115 1604 9702 00 BEAM 1 490 0663 3131 00 O-RING 2
120 1626 5792 00 BEAM 1 495 0246 1956 42 STUD 4
130 0147 1362 03 HEX. HEAD SCREW 6 500 0301 2344 00 PLAIN WASHER 4
140 0301 2344 00 PLAIN WASHER 6 505 0266 2111 00 HEXAGON NUT 4
145 1615 5664 00 HEX. HEAD SCREW 3 520 1604 2771 01 PLATE 2
150 1604 9674 00 PLATE 1 530 1615 5664 00 HEX. HEAD SCREW 4
155 1615 5664 00 HEX. HEAD SCREW 9 535 1604 2496 00 GROMMET 2
170 1604 9676 00 PLATE 1 560 1604 7685 00 PLATE 1
175 1615 5664 00 HEX. HEAD SCREW 9 565 1615 5664 00 HEX. HEAD SCREW 3
190 1604 9892 01 COWL 1 600 1619 5562 00 SEAL AR
195 1615 5664 00 HEX. HEAD SCREW 8
210 1626 5912 00 PLATE 1
220 1604 9704 00 PLATE 1
225 1615 5664 00 HEX. HEAD SCREW 12
260 1604 2707 81 PLATE ASSY 2
(For details see page 147)
265 0147 1326 03 HEX. HEAD SCREW 6
267 0301 2335 00 PLAIN WASHER 6
See Page 46
See Page 83
See Page 38
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 83
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 83
See Page 83
See Page 79 or 82
See Page 83
See Page 46
See Page 162 or 163
See Page 38
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 83
See Page 79 or 82
See Page 83
See Page 46
See Page 83
See Page 264
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
120 1089 0659 03 LEVEL SENSOR 1 617 0301 2321 00 PLAIN WASHER 4
125 0147 1212 03 HEX. HEAD SCREW 5 620 0347 6105 00 HOSE CLAMP 1
130 0301 2318 00 PLAIN WASHER 5 625 0072 8403 16 HOSE AR
150 1604 7585 00 HOSE 1 630 1604 4399 01 MANIFOLD 1
155 0347 6100 22 HOSE CLAMP 2 640 1604 2779 01 CONNECTION 1
300 0099 9910 47 PLASTIC TUBE AR 645 1604 2780 02 GASKET 1
305 1626 0264 80 NIPPLE ASSY. 2 700 1626 1266 00 CLAMP HOSE 13
A10 1626 0264 00 NIPPLE 1 710 0348 0101 05 CABLE TIE 13
A20 1626 0265 00 NIPPLE 1
A30 1626 0266 00 WASHER 1
A40 0517 1100 31 BEARING BALL 1
306 0347 6108 00 HOSE CLAMP 2
307 0147 1322 03 HEX. HEAD SCREW 3
308 0333 3227 00 LOCK WASHER 3
309 0266 2110 00 HEXAGON NUT 3
310 0099 9910 47 PLASTIC TUBE AR
311 1626 0999 00 SUPPORT 2
313 1615 1789 00 BRACKET 1
314 1503 1056 00 SEAL AR
315 0347 6108 00 HOSE CLAMP 2
320 9000 0246 00 HOSE NIPPLE 1
380 1604 2742 00 FUEL COOLER 1
390 1615 5664 00 HEX. HEAD SCREW 3
415 0147 1363 03 HEX. HEAD SCREW 2
420 0301 2344 00 PLAIN WASHER 2
485 1079 5840 21 BUSHING 1
490 0653 1128 00 GASKET 1
495 0571 0020 43 HOSE NIPPLE 1
500 0075 4025 70 HOSE AR
520 0571 0020 43 HOSE NIPPLE 2
525 0582 0000 58 BODY 2
530 0075 4025 70 HOSE AR
550 1604 8273 00 QUICK CONNECTION 1
560 0075 4025 69 TUBE AR
565 0347 6103 00 HOSE CLAMP 1
570 1079 5840 28 HEXAGON NIPPLE 1
575 0653 1100 00 FLAT GASKET 1
580 1604 2799 00 ELBOW 1
585 0075 4025 69 TUBE AR
590 0347 6103 00 HOSE CLAMP 1
610 1604 2780 02 GASKET 2
615 0147 1250 03 HEX. HEAD SCREW 4
See Page 94
- 165 -
TOWING EYES - NATO EYE, SWE EYE, ITA EYE WAGON - OPTIONS
- 166 -
TIE DOWN LOOPS - OPTIONS
See Page 95
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 95
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 95
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 95
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 95
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
15 1604 4239 86 FRAME 1 310 1619 2766 00 HEX. HEAD SCREW 6 810 0129 3110 00 BLIND RIVET 4
(For details see page 252) 320 1604 4346 02 MUDGUARD 4 850 1604 4338 00 PROTECTION 1
16 1079 3463 07 U-BOLT 1 330 1615 5664 00 HEX. HEAD SCREW 12 855 1615 5664 00 HEX. HEAD SCREW 2
17 0301 2335 00 PLAIN WASHER 4 340 1088 0801 53 GROMMET 1
20 1604 4784 01 AXLE FRONT/REAR 1 345 1604 4363 00 HOSE AR
25 0333 5200 08 WASHER 8 347 1604 4364 00 HOSE AR
- 1079 0003 33 SILENCING FOAM
30 0147 1476 03 HEX. HEAD SCREW 8 348 1604 4365 00 HOSE AR
2000 mm x 1500 mm x 50 mm
35 1604 3528 01 BRAKE CABLE 2 350 1604 5135 01 BRAKE ABS TD 1
50 1604 4784 01 AXLE FRONT/REAR 1 (For details see page 256)
55 0333 5200 08 WASHER 8 355 1604 3350 00 SUPPORT 1
60 0147 1476 03 HEX. HEAD SCREW 8 360 1615 5664 00 HEX. HEAD SCREW 3
80 1604 4786 02 TOWBAR 1 370 1604 3351 00 CLAMP 1
A800 2914 2437 00 HAND BRAKE LEVER 0 375 1615 5664 00 HEX. HEAD SCREW 2
A810 2914 2438 00 CABLE HANDBRAKE 0 380 1604 4843 01 SUB FRAME 1
90 0147 1962 89 HEX. HEAD SCREW 10 390 1615 5664 00 HEX. HEAD SCREW 4
95 0300 0274 96 PLAIN WASHER 4 400 0147 1245 03 HEX. HEAD SCREW 4
100 0300 0276 22 PLAIN WASHER 6 402 0301 2321 00 PLAIN WASHER 4
150 1615 9260 82 TYRE ASSY 4 410 1604 4844 00 SUPPORT 1
B20 0538 0400 19 TYRE 1 420 1615 5664 00 HEX. HEAD SCREW 4
B25 1626 0078 00 WHEEL 1 430 0147 1336 03 HEX. HEAD SCREW 4
B30 1615 6691 00 VENTIL 1 440 0301 2335 00 PLAIN WASHER 4
160 1079 9917 99 INFORMATION LABEL 2 450 0266 2110 00 HEXAGON NUT 4
230 0147 1465 03 HEX. HEAD SCREW 2 460 0147 1329 03 HEX. HEAD SCREW 2
235 0147 1962 18 HEX. HEAD SCREW 2 461 0301 2335 00 PLAIN WASHER 2
240 0301 2358 00 PLAIN WASHER 4 462 0291 1110 00 LOCKNUT 2
260 1604 3588 01 PROTECTION 1 470 0301 2335 00 PLAIN WASHER 8
262 1615 5664 00 HEX. HEAD SCREW 4 480 0291 1110 00 LOCKNUT 4
263 - SILENCING FOAM (50 mm) 1 490 0147 1326 03 HEX. HEAD SCREW 4
264 - SILENCING FOAM (50 mm) 1 500 1604 4704 00 STRIP 1
265 1604 3589 01 PROTECTION 1 505 0147 1259 03 HEX. HEAD SCREW 2
267 1615 5664 00 HEX. HEAD SCREW 5 510 0301 2321 00 PLAIN WASHER 2
268 - SILENCING FOAM (50 mm) 1 580 0346 1000 17 PIPE CLAMP 24
269 - SILENCING FOAM (50 mm) 1 590 0147 1246 03 HEX. HEAD SCREW 24
270 1604 3590 01 PROTECTION 1 600 0333 3220 00 LOCK WASHER 24
275 1615 5664 00 HEX. HEAD SCREW 5 610 0266 2108 00 HEXAGON NUT 24
277 - SILENCING FOAM (50 mm) 1 680 1079 9926 73 INSTRUCTION LABEL 1
278 - SILENCING FOAM (50 mm) 1 710 1604 4318 00 SEAL AR
280 1604 3587 01 PROTECTION 1 720 1615 6478 01 BRACKET 1
285 1615 5664 00 HEX. HEAD SCREW 4 730 1615 5664 00 HEX. HEAD SCREW 1
287 - SILENCING FOAM (50 mm) 1 740 1615 5614 00 BRACKET 2
288 - SILENCING FOAM (50 mm) 1 750 0147 1249 03 HEX. HEAD SCREW 2
300 1604 3763 02 PLATE 2 760 1604 3674 00 CABLE 1
See Page 86 or 88
See Page 86 or 88
See Page 44
See Page 83
See Page 79 or 82
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 73
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
20 1604 3369 01 MANIFOLD 1 240 1612 0685 83 VALVE 1 675 0129 3101 00 RIVET 3
25 0686 3716 10 PLUG 1 A20 1612 0685 00 BLEEDER VALVE HOUSING 1 680 0301 2318 00 WASHER 3
27 0653 1254 00 GASKET 1 A30 1612 0686 00 SPRING 1 850 0661 1049 00 WASHER 1
30 0634 1000 57 COUPLING 1 A40 0663 3117 00 O-RING 1 855 0686 3716 07 PLUG 1
35 1604 3370 03 HOSE 1 A50 1612 0687 00 VALVE 1
40 0663 7141 00 O-RING 1 A60 1612 0688 00 LOCK SPRING 1
45 0147 1403 03 SCREW 4 400 1613 0807 00 BRACKET 2
50 0301 2358 00 WASHER 4 405 1615 5664 00 SCREW 1
60 1604 3355 02 COOLER 1 470 1604 5107 01 PIPE 1
65 1604 3366 01 SUPPORT 1 472 1604 1792 01 CLAMP 1
70 0147 1359 03 SCREW 4 475 1604 5112 00 PIPE 1
75 0301 2344 00 WASHER 4 477 1079 9902 55 DECAL 1
80 0147 1362 03 SCREW 3 480 1604 3364 02 SUPPORT 1
85 0301 2344 00 WASHER 3 485 0147 1359 03 SCREW 2
90 1604 3365 04 SUPPORT 1 490 0301 2344 00 WASHER 2
95 0147 1359 03 SCREW 4 495 0147 1362 03 SCREW 2
100 0301 2344 00 WASHER 4 500 0301 2344 00 WASHER 2
110 1615 5664 00 SCREW 2 505 0266 2111 00 NUT 2
115 0300 0274 91 WASHER 1 510 1604 1792 01 CLAMP 1
120 1604 5106 01 PIPE 1 520 1604 3371 01 MANIFOLD 1
125 0663 7141 00 O-RING 1 525 0147 1362 03 SCREW 4
130 0147 1403 03 SCREW 4 530 0301 2344 00 WASHER 4
135 0301 2358 00 WASHER 4 535 1089 0574 70 SENSOR 1
140 1604 2100 01 SEPARATOR 1 540 5501 5959 00 PLUG 1
145 0663 2107 46 O- RING 2 560 0852 0010 40 VALVE 1
165 0246 1283 04 BOLT 8 565 0623 2100 13 NUT 1
170 0301 2358 00 WASHER 8 590 1604 4760 01 SUPPORT 1
175 0266 2112 00 NUT 8 595 1615 5664 00 SCREW 2
180 0653 1124 00 GASKET 1 600 1604 3550 83 PANEL 1
183 0603 4200 38 FITTING 1 (For details see page 247)
184 0653 1124 00 GASKET 1 610 1615 5664 00 SCREW 2
185 0803 5010 08 STRAINER 1 615 1604 3551 81 PANEL 1
186 0653 1124 00 GASKET 1 (For details see page 248)
187 1604 6697 00 RESTRICTOR 1 625 1615 5664 00 SCREW 7
188 0581 1200 27 FITTING 1 630 1604 3552 02 SUPPORT 1
190 0070 6002 06 PIPE AR 635 1615 5664 00 SCREW 2
192 0581 0000 53 COUPLING 1 650 1604 2689 84 PANEL 1
193 0653 1124 00 GASKET 2 (For details see page 244)
194 0560 0200 29 FITTING 1 660 1604 2678 82 CORNER 1
195 9090 0510 00 SILENCER 1 (For details see page 243)
220 0661 1049 00 WASHER 1 662 0686 9252 69 PLUG 1
670 1616 4615 00 BAND 1
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
20 1604 3369 01 MANIFOLD 1 190 0070 6002 06 PIPE AR 475 1604 5112 00 PIPE 1
25 0686 3716 10 PLUG 1 192 0581 0000 53 COUPLING 1 477 1079 9902 55 DECAL 1
27 0653 1254 00 GASKET 1 193 0653 1124 00 GASKET 3 480 1604 3364 02 SUPPORT 1
30 0634 1000 57 COUPLING 1 194 0560 0200 29 FITTING 1 485 0147 1359 03 SCREW 2
35 1604 3370 03 HOSE 1 195 9090 0510 00 SILENCER 1 490 0301 2344 00 WASHER 2
40 0663 7141 00 O-RING 1 201 0147 1362 03 SCREW 2 495 0147 1362 03 SCREW 2
45 0147 1403 03 SCREW 4 202 0301 2344 00 WASHER 2 500 0301 2344 00 WASHER 2
50 0301 2358 00 WASHER 4 220 0661 1049 00 WASHER 1 505 0266 2111 00 NUT 2
60 1604 3355 02 COOLER 1 240 1612 0685 83 VALVE 1 510 1604 1792 01 CLAMP 1
65 1604 3366 01 SUPPORT 1 A20 1612 0685 00 BLEEDER VALVE HOUSING 1 520 1604 3371 01 MANIFOLD 1
70 0147 1359 03 SCREW 4 A30 1612 0686 00 SPRING 1 525 0147 1362 03 SCREW 4
75 0301 2344 00 WASHER 4 A40 0663 3117 00 O-RING 1 530 0301 2344 00 WASHER 4
80 0147 1362 03 SCREW 3 A50 1612 0687 00 VALVE 1 535 1089 0574 70 SENSOR 1
85 0301 2344 00 WASHER 3 A60 1612 0688 00 LOCK SPRING 1 540 5501 5959 00 PLUG 1
90 1604 3365 04 SUPPORT 1 250 1604 5249 00 FLANGE 1 560 0852 0010 40 VALVE 1
95 0147 1359 03 SCREW 4 252 1604 5248 00 GASKET 1 565 0623 2100 13 NUT 1
100 0301 2344 00 WASHER 4 255 1604 5246 00 COUPLING 1 590 1604 4760 01 SUPPORT 1
105 1615 5664 00 SCREW 3 256 1604 5246 00 COUPLING 1 595 1615 5664 00 SCREW 2
110 1615 5664 00 SCREW 2 257 0663 9244 00 O- RING 1 600 1604 3550 83 PANEL 1
115 0300 0274 91 WASHER 1 260 0661 1026 00 SEAL 1 (For details see page 247)
120 1604 5106 01 PIPE 1 262 0607 1151 07 SOCKET 1 610 1615 5664 00 SCREW 2
125 0663 7141 00 O-RING 1 265 0653 1062 00 GASKET 1 615 1604 3551 81 PANEL 1
130 0147 1403 03 SCREW 4 267 0844 1100 05 VALVE 1 (For details see page 248)
135 0301 2358 00 WASHER 4 270 0581 1200 14 COUPLING 1 625 1615 5664 00 SCREW 7
140 1604 2100 01 SEPARATOR 1 275 1604 5247 01 PIPE 1 630 1604 3552 02 SUPPORT 1
145 0663 2107 46 O- RING 2 277 1503 1056 00 PROTECTION AR 635 1615 5664 00 SCREW 2
147 1604 5108 01 PIPE 1 320 0211 1244 00 SCREW 2 650 1604 2689 84 PANEL 1
150 8102 2603 31 FILTER 1 321 0583 8120 62 COUPLING 2 (For details see page 244)
155 0663 2104 98 O- RING 1 322 0070 6002 20 TUBE 3 660 1604 2678 82 CORNER 1
165 0246 1283 04 BOLT 8 325 0583 8120 10 COUPLING 2 (For details see page 243)
170 0301 2358 00 WASHER 8 327 1604 5257 00 SUPPORT 1 662 0686 9252 69 PLUG 1
172 0266 2112 00 NUT 8 330 0147 1205 03 SCREW 2 670 1616 4615 00 BAND 1
174 0147 1362 03 SCREW 2 332 0301 2318 00 WASHER 2 675 0129 3101 00 RIVET 3
175 0301 2344 00 WASHER 2 335 0333 3215 00 LOCK 2 680 0301 2318 00 WASHER 3
176 0266 2111 00 NUT 2 337 1613 0801 00 CLAMP 2 850 0661 1049 00 WASHER 1
180 0653 1124 00 GASKET 1 340 0147 1247 03 SCREW 2 855 0686 3716 07 PLUG 1
183 0603 4200 38 FITTING 1 342 0301 2321 00 WASHER 2
184 0653 1124 00 GASKET 1 345 0333 3220 00 LOCK 2
185 0803 5010 08 STRAINER 1 400 1613 0807 00 BRACKET 2
186 0653 1124 00 GASKET 1 405 1615 5664 00 SCREW 1
187 1604 6697 00 RESTRICTOR 1 470 1604 5109 01 PIPE 1
188 0581 1200 27 FITTING 1 472 1604 1792 01 CLAMP 1
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
20 1604 3369 01 MANIFOLD 1 192 0581 0000 53 COUPLING 1 335 0333 3215 00 LOCK 2
25 0686 3716 10 PLUG 1 193 0653 1124 00 GASKET 3 337 1613 0801 00 CLAMP 2
27 0653 1254 00 GASKET 1 194 0560 0200 29 FITTING 1 340 0147 1247 03 SCREW 2
30 0634 1000 57 COUPLING 1 195 9090 0510 00 SILENCER 1 342 0301 2321 00 WASHER 2
35 1604 3370 03 HOSE 1 201 0147 1362 03 SCREW 2 345 0333 3220 00 LOCK 2
40 0663 7141 00 O-RING 1 202 0301 2344 00 WASHER 2 400 1613 0807 00 BRACKET 2
45 0147 1403 03 SCREW 4 220 0661 1049 00 WASHER 1 405 1615 5664 00 SCREW 1
50 0301 2358 00 WASHER 4 240 1612 0685 83 VALVE 1 470 1604 5110 01 PIPE 1
60 1604 3355 02 COOLER 1 A20 1612 0685 00 BLEEDER VALVE HOUSING 1 472 1604 1792 01 CLAMP 1
65 1604 3366 01 SUPPORT 1 A30 1612 0686 00 SPRING 1 475 1604 5112 00 PIPE 1
70 0147 1359 03 SCREW 4 A40 0663 3117 00 O-RING 1 477 1079 9902 55 DECAL 1
75 0301 2344 00 WASHER 4 A50 1612 0687 00 VALVE 1 480 1604 3364 02 SUPPORT 1
80 0147 1362 03 SCREW 3 A60 1612 0688 00 LOCK SPRING 1 485 0147 1359 03 SCREW 2
85 0301 2344 00 WASHER 3 250 1604 5249 00 FLANGE 1 490 0301 2344 00 WASHER 2
90 1604 3365 04 SUPPORT 1 252 1604 5248 00 GASKET 1 495 0147 1362 03 SCREW 2
95 0147 1359 03 SCREW 4 255 1604 5246 00 COUPLING 1 500 0301 2344 00 WASHER 2
100 0301 2344 00 WASHER 4 256 1604 5246 00 COUPLING 1 505 0266 2111 00 NUT 2
105 1615 5664 00 SCREW 3 257 0663 9244 00 O- RING 1 510 1604 1792 01 CLAMP 1
110 1615 5664 00 SCREW 2 260 0661 1026 00 SEAL 1 520 1604 3371 01 MANIFOLD 1
115 0300 0274 91 WASHER 1 262 0607 1151 07 SOCKET 1 525 0147 1362 03 SCREW 4
120 1604 5106 01 PIPE 1 265 0653 1062 00 GASKET 1 530 0301 2344 00 WASHER 4
125 0663 7141 00 O-RING 1 267 0844 1100 05 VALVE 1 535 1089 0574 70 SENSOR 1
130 0147 1403 03 SCREW 4 270 0581 1200 14 COUPLING 1 540 5501 5959 00 PLUG 1
135 0301 2358 00 WASHER 4 275 1604 5247 01 PIPE 1 560 0852 0010 40 VALVE 1
140 1604 2100 01 SEPARATOR 1 277 1503 1056 00 PROTECTION AR 565 0623 2100 13 NUT 1
145 0663 2107 46 O- RING 2 280 1604 5249 00 FLANGE 1 590 1604 4760 01 SUPPORT 1
147 1604 5108 01 PIPE 1 282 1604 5248 00 GASKET 1 595 1615 5664 00 SCREW 2
150 8102 2603 31 FILTER 1 285 1604 5246 00 COUPLING 1 600 1604 3550 83 PANEL 1
155 0663 2104 98 O- RING 1 286 1604 5246 00 COUPLING 1 (For details see page 247)
160 8102 2603 56 FILTER 1 287 0663 9244 00 O- RING 1 610 1615 5664 00 SCREW 2
162 8092 2430 40 CONNECTION SET 1 290 0661 1026 00 SEAL 1 615 1604 3551 81 PANEL 1
165 0246 1283 04 BOLT 8 292 0607 1151 07 SOCKET 1 (For details see page 248)
170 0301 2358 00 WASHER 8 295 0653 1062 00 GASKET 1 625 1615 5664 00 SCREW 7
172 0266 2112 00 NUT 8 297 0844 1100 05 VALVE 1 630 1604 3552 02 SUPPORT 1
174 0147 1362 03 SCREW 2 300 0581 1200 14 COUPLING 1 635 1615 5664 00 SCREW 2
175 0301 2344 00 WASHER 2 305 1604 5247 01 PIPE 1 650 1604 2689 84 PANEL 1
176 0266 2111 00 NUT 2 307 1503 1056 00 PROTECTION AR (For details see page 247)
180 0653 1124 00 GASKET 1 320 0211 1244 00 SCREW 2 660 1604 2678 82 CORNER 1
183 0603 4200 38 FITTING 1 321 0583 8120 62 COUPLING 2 (For details see page 243)
184 0653 1124 00 GASKET 1 322 0070 6002 20 TUBE 3 662 0686 9252 69 PLUG 1
185 0803 5010 08 STRAINER 1 325 0583 8120 10 COUPLING 2 670 1616 4615 00 BAND 1
186 0653 1124 00 GASKET 1 327 1604 5257 00 SUPPORT 1 675 0129 3101 00 RIVET 3
187 1604 6697 00 RESTRICTOR 1 330 0147 1205 03 SCREW 2 680 0301 2318 00 WASHER 3
188 0581 1200 27 FITTING 1 332 0301 2318 00 WASHER 2 850 0661 1049 00 WASHER 1
190 0070 6002 06 PIPE AR 855 0686 3716 07 PLUG 1
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
20 1604 3369 01 MANIFOLD 1 202 0301 2344 00 WASHER 2 660 1604 2678 82 CORNER 1
25 0686 3716 10 PLUG 1 220 0661 1049 00 WASHER 1 (For details see page 243)
27 0653 1254 00 GASKET 1 240 1612 0685 83 VALVE 1 662 0686 9252 69 PLUG 1
30 0634 1000 57 COUPLING 1 A20 1612 0685 00 BLEED.VALVE HSG 1 670 1616 4615 00 BAND 1
35 1604 3370 03 HOSE 1 A30 1612 0686 00 SPRING 1 675 0129 3101 00 RIVET 3
40 0663 7141 00 O-RING 1 A40 0663 3117 00 O-RING 1 680 0301 2318 00 WASHER 3
45 0147 1403 03 SCREW 4 A50 1612 0687 00 VALVE 1 690 0653 1124 00 GASKET 1
50 0301 2358 00 WASHER 4 A60 1612 0688 00 LOCK SPRING 1 695 0686 3716 02 PLUG 1
60 1604 3355 02 COOLER 1 400 1613 0807 00 BRACKET 2 700 1604 3384 00 ADAPTER 1
65 1604 3366 01 SUPPORT 1 405 1615 5664 00 SCREW 1 701 0147 1372 03 SCREW 3
70 0147 1359 03 SCREW 4 470 1604 5107 01 PIPE 1 702 0266 2111 00 NUT 3
75 0301 2344 00 WASHER 4 472 1604 1792 01 CLAMP 1 705 0661 1056 00 SEAL 1
80 0147 1362 03 SCREW 3 475 1604 5111 00 PIPE 1 709 1626 4720 00 BRACKET 2
85 0301 2344 00 WASHER 3 477 1079 9902 55 DECAL 1 710 1079 5840 06 FITTING 1
90 1604 3365 04 SUPPORT 1 480 1604 3364 02 SUPPORT 1 711 1619 2861 01 CLAMP 2
95 0147 1359 03 SCREW 4 485 0147 1359 03 SCREW 2 712 0147 1327 03 SCREW 2
100 0301 2344 00 WASHER 4 490 0301 2344 00 WASHER 2 713 0333 3227 00 LOCK 2
105 1615 5664 00 SCREW 3 495 0147 1362 03 SCREW 2 714 0266 2110 00 NUT 2
110 1615 5664 00 SCREW 2 500 0301 2344 00 WASHER 2 716 1619 2861 01 CLAMP 4
115 0300 0274 91 WASHER 1 505 0266 2111 00 NUT 2 717 0147 1327 03 SCREW 2
120 1604 5106 01 PIPE 1 510 1604 1792 01 CLAMP 1 718 0333 3227 00 LOCK 2
125 0663 7141 00 O-RING 1 520 1604 3371 01 MANIFOLD 1 719 0266 2110 00 NUT 2
130 0147 1403 03 SCREW 4 525 0147 1362 03 SCREW 4 721 0246 1956 42 ROD 4
135 0301 2358 00 WASHER 4 530 0301 2344 00 WASHER 4 722 0301 2344 00 WASHER 4
140 1604 2100 01 SEPARATOR 1 535 1089 0574 70 SENSOR 1 723 0266 2111 00 NUT 4
145 0663 2107 46 O- RING 2 540 5501 5959 00 PLUG 1 726 1079 9902 55 DECAL 1
165 0246 1283 04 BOLT 8 560 0852 0010 40 VALVE 1 727 1604 3359 02 HEAT EXCHANGER 1
170 0301 2358 00 WASHER 8 565 0623 2100 12 NUT 1 728 0663 3132 00 O- RING 2
175 0266 2112 00 NUT 8 590 1604 4760 01 SUPPORT 1 730 1604 7228 00 PIPE 1
180 0653 1124 00 GASKET 1 595 1615 5664 00 SCREW 2 732 1604 4732 01 PIPE 1
183 0603 4200 38 FITTING 1 600 1604 3550 83 PANEL 1 736 1619 2861 01 CLAMP 1
184 0653 1124 00 GASKET 1 (For details see page 247) 737 0147 1322 03 SCREW 1
185 0803 5010 08 STRAINER 1 610 1615 5664 00 SCREW 2 738 0333 3227 00 LOCK 1
186 0653 1124 00 GASKET 1 615 1604 3551 81 PANEL 1 739 0266 2110 00 NUT 1
187 1604 6697 00 RESTRICTOR 1 (For details see page 248) 740 1079 5840 06 FITTING 1
188 0581 1200 27 FITTING 1 625 1615 5664 00 SCREW 7 745 0661 1056 00 SEAL 1
190 0070 6002 06 PIPE AR 626 1615 1789 00 BRACKET 1 750 0663 9868 00 O- RING 2
192 0581 0000 53 COUPLING 1 630 1604 3552 02 SUPPORT 1 752 0211 1364 00 SCREW 3
193 0653 1124 00 GASKET 3 635 1615 5664 00 SCREW 2 755 1604 3585 00 ADAPTER 1
194 0560 0200 29 FITTING 1 650 1604 2689 84 PANEL 1 758 0147 1375 03 SCREW 3
195 9090 0510 00 SILENCER 1 (For details see page 244) 760 1626 3138 00 HOSE ASSEMBLY 1
201 0147 1362 03 SCREW 2 651 1503 1056 00 PROTECTION AR (Continued on page 199)
See Page 80
See Page 80
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 80
See Page 80
1611 8191 67_ed02
See Page 80
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
20 1604 3369 01 MANIFOLD 1 192 0581 0000 53 COUPLING 1 485 0147 1359 03 SCREW 2
25 0686 3716 10 PLUG 1 193 0653 1124 00 GASKET 2 490 0301 2344 00 WASHER 2
27 0653 1254 00 GASKET 1 194 0560 0200 29 FITTING 1 495 0147 1362 03 SCREW 2
30 0634 1000 57 COUPLING 1 195 9090 0510 00 SILENCER 1 500 0301 2344 00 WASHER 2
35 1604 3370 03 HOSE 1 220 0661 1049 00 WASHER 1 505 0266 2111 00 NUT 2
40 0663 7141 00 O-RING 1 240 1612 0685 83 VALVE 1 510 1604 1792 01 CLAMP 1
45 0147 1403 03 SCREW 4 A20 1612 0685 00 BLEEDER VALVE HOUSING 1 520 1604 3371 01 MANIFOLD 1
50 0301 2358 00 WASHER 4 A30 1612 0686 00 SPRING 1 525 0147 1362 03 SCREW 4
60 1604 3355 02 COOLER 1 A40 0663 3117 00 O-RING 1 530 0301 2344 00 WASHER 4
65 1604 3366 01 SUPPORT 1 A50 1612 0687 00 VALVE 1 535 1089 0574 70 SENSOR 1
70 0147 1359 03 SCREW 4 A60 1612 0688 00 LOCK SPRING 1 540 5501 5959 00 PLUG 1
75 0301 2344 00 WASHER 4 250 1604 5249 00 FLANGE 1 560 0852 0010 40 VALVE 1
80 0147 1362 03 SCREW 3 252 1604 5248 00 GASKET 1 565 0623 2100 13 NUT 1
85 0301 2344 00 WASHER 3 256 1604 5246 00 COUPLING 1 590 1604 4760 01 SUPPORT 1
90 1604 3365 04 SUPPORT 1 257 0663 9244 00 O- RING 1 595 1615 5664 00 SCREW 2
95 0147 1359 03 SCREW 4 260 0661 1026 00 SEAL 1 600 1604 3550 83 PANEL 1
100 0301 2344 00 WASHER 4 262 0607 1151 07 SOCKET 1 (For details see page 247)
110 1615 5664 00 SCREW 2 265 0653 1062 00 GASKET 1 610 1615 5664 00 SCREW 2
115 0300 0274 91 WASHER 1 267 0844 1100 05 VALVE 1 615 1604 3551 81 PANEL 1
120 1604 5106 01 PIPE 1 270 0581 1200 14 COUPLING 1 (For details see page 248)
125 0663 7141 00 O-RING 1 275 1604 5247 01 PIPE 1 625 1615 5664 00 SCREW 7
130 0147 1403 03 SCREW 4 277 1503 1056 00 PROTECTION AR 626 1615 1789 00 BRACKET 1
135 0301 2358 00 WASHER 4 321 0583 8120 62 COUPLING 2 630 1604 3552 02 SUPPORT 1
140 1604 2100 01 SEPARATOR 1 322 0070 6002 20 TUBE 3 635 1615 5664 00 SCREW 2
145 0663 2107 46 O- RING 2 325 0583 8120 10 COUPLING 2 650 1604 2689 84 PANEL 1
147 1604 5108 01 PIPE 1 327 1604 5257 00 SUPPORT 1 (For details see page 244)
150 8102 2603 31 FILTER 1 330 0147 1205 03 SCREW 2 651 1503 1056 00 PROTECTION AR
155 0663 2104 98 O- RING 1 332 0301 2318 00 WASHER 2 660 1604 2678 82 CORNER 1
165 0246 1283 04 BOLT 8 335 0333 3215 00 LOCK 2 (For details see page 243)
170 0301 2358 00 WASHER 8 337 1613 0801 00 CLAMP 2 662 0686 9252 69 PLUG 1
172 0266 2112 00 NUT 8 340 0147 1247 03 SCREW 2 670 1616 4615 00 BAND 1
174 0147 1362 03 SCREW 2 342 0301 2321 00 WASHER 2 675 0129 3101 00 RIVET 3
175 0301 2344 00 WASHER 2 345 0333 3220 00 LOCK 2 680 0301 2318 00 WASHER 3
176 0266 2111 00 NUT 2 400 1613 0807 00 BRACKET 2 690 0653 1124 00 GASKET 1
180 0653 1124 00 GASKET 1 405 1615 5664 00 SCREW 1 695 0686 3716 02 PLUG 1
183 0603 4200 38 FITTING 1 470 1604 5109 01 PIPE 1 700 1604 3384 00 ADAPTER 1
184 0653 1124 00 GASKET 1 472 1604 1792 01 CLAMP 1 701 0147 1372 03 SCREW 3
185 0803 5010 08 STRAINER 1 475 1604 5111 00 PIPE 1 702 0266 2111 00 NUT 3
186 0653 1124 00 GASKET 1 477 1079 9902 55 DECAL 1 705 0661 1056 00 SEAL 1
187 1604 6697 00 RESTRICTOR 1 478 0661 1062 00 WASHER 1 709 1626 4720 00 BRACKET 2
188 0581 1200 27 FITTING 1 479 0686 3716 10 PLUG 1 710 1079 5840 06 FITTING 1
190 0070 6002 06 PIPE AR 480 1604 3364 02 SUPPORT 1 (Continued on page 202)
See Page 80
See Page 80
1611 8191 67_ed02
See Page 80
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 80
1611 8192 67_ed02
See Page 80
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
20 1604 3369 01 MANIFOLD 1 187 1604 6697 00 RESTRICTOR 1 325 0583 8120 10 COUPLING 2
25 0686 3716 10 PLUG 1 188 0581 1200 27 FITTING 1 327 1604 5257 00 SUPPORT 1
27 0653 1254 00 GASKET 1 190 0070 6002 06 PIPE AR 330 0147 1205 03 SCREW 2
30 0634 1000 57 COUPLING 1 192 0581 0000 53 COUPLING 1 332 0301 2318 00 WASHER 2
35 1604 3370 03 HOSE 1 193 0653 1124 00 GASKET 3 335 0333 3215 00 LOCK 2
40 0663 7141 00 O-RING 1 194 0560 0200 29 FITTING 1 337 1613 0801 00 CLAMP 2
45 0147 1403 03 SCREW 4 195 9090 0510 00 SILENCER 1 340 0147 1247 03 SCREW 2
50 0301 2358 00 WASHER 4 201 0147 1362 03 SCREW 2 342 0301 2321 00 WASHER 2
60 1604 3355 02 COOLER 1 202 0301 2344 00 WASHER 2 345 0333 3220 00 LOCK 2
65 1604 3366 01 SUPPORT 1 220 0661 1049 00 WASHER 1 400 1613 0807 00 BRACKET 2
70 0147 1359 03 SCREW 4 240 1612 0685 83 VALVE 1 405 1615 5664 00 SCREW 1
75 0301 2344 00 WASHER 4 A20 1612 0685 00 BLEEDER VALVE HOUSING 1 470 1604 5110 01 PIPE 1
80 0147 1362 03 SCREW 3 A30 1612 0686 00 SPRING 1 472 1604 1792 01 CLAMP 1
85 0301 2344 00 WASHER 3 A40 0663 3117 00 O-RING 1 475 1604 5111 00 PIPE 1
90 1604 3365 04 SUPPORT 1 A50 1612 0687 00 VALVE 1 477 1079 9902 55 DECAL 1
95 0147 1359 03 SCREW 4 A60 1612 0688 00 LOCK SPRING 1 480 1604 3364 02 SUPPORT 1
100 0301 2344 00 WASHER 4 250 1604 5249 00 FLANGE 1 485 0147 1359 03 SCREW 2
105 1615 5664 00 SCREW 3 252 1604 5248 00 GASKET 1 490 0301 2344 00 WASHER 2
110 1615 5664 00 SCREW 2 255 1604 5246 00 COUPLING 1 495 0147 1362 03 SCREW 2
115 0300 0274 91 WASHER 1 256 1604 5246 00 COUPLING 1 500 0301 2344 00 WASHER 2
120 1604 5106 01 PIPE 1 257 0663 9244 00 O- RING 1 505 0266 2111 00 NUT 2
125 0663 7141 00 O-RING 1 260 0661 1026 00 SEAL 1 510 1604 1792 01 CLAMP 1
130 0147 1403 03 SCREW 4 262 0607 1151 07 SOCKET 1 520 1604 3371 01 MANIFOLD 1
135 0301 2358 00 WASHER 4 265 0653 1062 00 GASKET 1 525 0147 1362 03 SCREW 4
140 1604 2100 01 SEPARATOR 1 267 0844 1100 05 VALVE 1 530 0301 2344 00 WASHER 4
145 0663 2107 46 O- RING 2 270 0581 1200 14 COUPLING 1 535 1089 0574 70 SENSOR 1
147 1604 5108 01 PIPE 1 275 1604 5247 01 PIPE 1 540 5501 5959 00 PLUG 1
150 8102 2603 31 FILTER 1 277 1503 1056 00 PROTECTION AR 560 0852 0010 40 VALVE 1
155 0663 2104 98 O- RING 1 280 1604 5249 00 FLANGE 1 565 0623 2100 13 NUT 1
160 8102 2603 56 FILTER 1 282 1604 5248 00 GASKET 1 590 1604 4760 01 SUPPORT 1
162 8092 2430 40 CONNECTION SET 1 285 1604 5246 00 COUPLING 1 595 1615 5664 00 SCREW 2
165 0246 1283 04 BOLT 8 286 1604 5246 00 COUPLING 1 600 1604 3550 83 PANEL 1
170 0301 2358 00 WASHER 8 287 0663 9244 00 O- RING 1 (For details see page 247)
172 0266 2112 00 NUT 8 290 0661 1026 00 SEAL 1 610 1615 5664 00 SCREW 2
174 0147 1362 03 SCREW 2 292 0607 1151 07 SOCKET 1 615 1604 3551 81 PANEL 1
175 0301 2344 00 WASHER 2 295 0653 1062 00 GASKET 1 (For details see page 248)
176 0266 2111 00 NUT 2 297 0844 1100 05 VALVE 1 625 1615 5664 00 SCREW 7
180 0653 1124 00 GASKET 1 300 0581 1200 14 COUPLING 1 626 1615 1789 00 BRACKET 1
183 0603 4200 38 FITTING 1 305 1604 5247 01 PIPE 1 630 1604 3552 02 SUPPORT 1
184 0653 1124 00 GASKET 1 307 1503 1056 00 PROTECTION AR 635 1615 5664 00 SCREW 2
185 0803 5010 08 STRAINER 1 321 0583 8120 62 COUPLING 2
186 0653 1124 00 GASKET 1 322 0070 6002 20 TUBE 3 (Continued on page 204)
See Page 80
1611 8192 67_02
See Page 80
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 42
See Page 33
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
10 1604 4779 02 WIRE HARNESS 1 420 1615 5664 00 HEX. HEAD SCREW 12
20 1615 9602 00 CONNECTOR USA 430 1088 0801 52 GROMMET 1
ROADSIGNALISATION 1 440 1604 0383 00 SEAL (OIL SEPARATOR) 2
30 0147 1325 03 HEX. HEAD SCREW 2 480 1079 9902 38 INFORMATION LABEL 2
40 0266 2110 00 HEXAGON NUT 2
50 0301 2335 00 PLAIN WASHER 2
60 1604 4775 00 LIGHT 2
70 0147 1249 03 HEX. HEAD SCREW 4
80 0266 2108 00 HEXAGON NUT 4
90 0301 2321 00 PLAIN WASHER 4
100 1202 9402 01 REFLECTOR 2
110 0266 2108 00 HEXAGON NUT 4
120 0301 2321 00 PLAIN WASHER 4
130 1604 4777 00 LIGHT 2
140 0147 1208 03 HEX. HEAD SCREW 4
150 0266 2107 00 HEXAGON NUT 4
160 0301 2318 00 PLAIN WASHER 4
170 1604 4773 00 LIGHT 2
180 0147 1208 03 HEX. HEAD SCREW 4
190 0266 2107 00 HEXAGON NUT 4
200 0301 2318 00 PLAIN WASHER 4
210 1604 4778 01 BRACKET 1
220 0147 1325 03 HEX. HEAD SCREW 2
230 0266 2110 00 HEXAGON NUT 2
240 0301 2335 00 PLAIN WASHER 4
250 1604 4774 00 LIGHT 3
260 0147 1208 03 HEX. HEAD SCREW 6
270 0266 2107 00 HEXAGON NUT 6
280 0301 2318 00 PLAIN WASHER 6
290 1604 4776 00 LIGHT 2
300 0147 1208 03 HEX. HEAD SCREW 4
310 0266 2107 00 HEXAGON NUT 4
320 0301 2318 00 PLAIN WASHER 4
330 1604 4772 00 LIGHT 2
340 0147 1208 03 HEX. HEAD SCREW 4
350 0266 2107 00 HEXAGON NUT 4
360 0301 2318 00 PLAIN WASHER 4
370 1604 2809 03 BUMPER 1
380 0348 0110 03 ANCHOR PLATE 30
390 0129 3110 00 BLIND RIVET 30
400 0348 0101 05 CABLE TIE 40
410 1604 2536 01 PLATE 2
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 62
See Page 31
See Page 98 or 99
1604 2481 82_02
60
See Page 98 or 99
1604 3545 80_02
See Page 98 or 99
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
- 1604 4527 03 AXLE FRONT (From page 168) 235 2914 0402 00 WHEEL 2
20 2914 0381 00 BUSHING 4 240 2914 0403 00 WHEEL BOLT 2
25 2914 0327 00 GREASE NIPPLE 4 245 1619 2804 00 WHEEL BOLT 2
30 2914 0008 00 O-RING 2 250 1619 0319 00 SPRING WASHER 2
35 2914 0329 00 BUSHING 2 255 1619 0296 00 NUT 2
40 2914 0343 00 GREASE NIPPLE 2 260 2914 0091 00 BEARING 2
45 2914 0356 00 TORSION BAR 1 265 2900 1056 00 BEARING 2
50 2914 0112 00 BUSHING 2 270 2900 1057 00 CAP 2
65 1619 2444 00 BOLT 2 275 - HOUSING 1
70 1619 3809 00 NUT 2 (Not available separately)
75 2914 0382 00 BRACKET 1 280 2914 0404 00 BUSHING 2
80 2914 0383 00 BRACKET 1 285 2914 0405 00 BUSHING 1
85 2914 0092 00 BUSHING 4 290 0544 2108 00 LUBRICATING NIPPLE 1
90 2914 0093 00 STUD 2 295 2914 0406 00 STEERING ROD 2
95 2914 0094 00 RING 4 300 2914 0100 00 STUD 1
100 2914 0095 00 CAP 4 305 2914 0101 00 WASHER 1
105 0544 2108 00 LUBRICATING NIPPLE 4 310 2914 0102 00 NUT 1
110 2914 0085 00 CASTLED NUT 2 315 0544 2108 00 LUBRICATING NIPPLE 1
115 2914 0086 00 SPLIT PIN 2 320 2914 0103 00 STUD 1
120 2914 0083 00 RING 2 325 2914 0104 00 RING 1
125 2914 0084 00 SEAL NILOS 2 330 2914 0105 00 GASKET 2
130 2914 0102 00 NUT 2 335 2914 0106 00 O-RING 1
135 2914 0384 00 DISK 2 350 2914 0107 00 BUSH 1
140 2914 0333 00 BRAKE CAMSHAFT 2 365 2914 0407 00 BOLT 2
145 2914 0334 00 RING 2 370 2914 0408 00 HOLDER 2
150 2914 0385 00 O- RING 2 375 2914 0409 00 BOLT 4
155 2914 0386 00 DISC 2 380 2914 0410 00 SPRING WASHER 4
160 2914 0387 00 SAFETY RING 2 385 2914 0411 00 SENSOR 2
165 2914 0388 00 RING 2 390 2914 0412 00 BUSHING 2
170 2914 0389 00 DISC 2 395 2914 0413 00 HOLDER 2
175 2914 0390 00 SAFETY RING 2 400 2914 0414 00 HOLDER 2
180 2914 0391 00 SPRING 2 405 2914 0415 00 DISC 2
185 2914 0392 00 BRACKET 1
190 2914 0393 00 BRACKET 1
195 2914 0394 00 ADJUSTING ROD 2
200 2914 0395 00 ADJUSTING ROD 2
205 2914 0396 00 GREASE NIPPLE 2
210 2914 0397 00 BOLT 4
215 2914 0398 00 NUT 4
220 2914 0399 00 BRAKE SHOE 4
225 2914 0400 00 BUSH 2
230 2914 0401 00 SPRING 4
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
See Page 98 or 99
REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY REF PART NUMBER DESIGNATION QTY
- 1604 9841 89 FRAME/LARGE FUELTANK ASSY 204 0211 1249 03 HEX SOCK. SCREW 8
(From page 226, 235) 206 0301 2321 00 PLAIN WASHER 8
10 1604 2849 05 SUPPORT 2 208 1604 2511 06 PROTECTION 1
15 0147 1958 96 HEX. HEAD SCREW 8 210 1615 5664 00 HEX. HEAD SCREW 4
20 0301 2378 00 PLAIN WASHER 8 300 1626 4511 01 DOOR 1
25 1604 9841 06 FRAME 1 310 1604 1275 00 SEAL AR
30 1604 7860 04 COVER 1 320 1604 7601 00 HINGE 2
35 1604 8370 03 SEAL 2 330 1604 2519 01 LOCK 1
40 0147 1323 03 HEX. HEAD SCREW 16 335 1604 3743 00 LATCH 1
45 0301 2335 00 PLAIN WASHER 16 340 0301 2318 00 PLAIN WASHER 8
48 1613 2655 00 PLUG 5 350 0266 2107 00 HEXAGON NUT 8
50 1604 9842 81 FUELTANK ASSY 1 370 0160 0996 91 CROSS REC SCREW 8
(For details see page 267) 390 1626 5599 00 PLATE 1
52 1604 2492 02 SUPPORT 4 400 0301 2335 00 PLAIN WASHER 3
54 0147 1401 03 HEX. HEAD SCREW 4 410 0147 1323 03 HEX. HEAD SCREW 3
56 0301 2358 00 PLAIN WASHER 4
58 1604 1275 00 SEAL AR
60 1604 2473 00 SUPPORT 4
62 0147 1377 03 HEX. HEAD SCREW 4
64 0301 2344 00 PLAIN WASHER 8
66 0291 1111 00 LOCKNUT 4
68 0226 9920 14 LINK SCREW 4
70 0291 1111 00 LOCKNUT 4
72 1604 2471 00 RETAINER 4
74 0291 1110 00 LOCKNUT 4
76 0147 1343 03 HEX. HEAD SCREW 4
100 1604 9843 83 FUELTANK ASSY 1
(For details see page 268)
102 1604 2492 02 SUPPORT 5
104 0147 1401 03 HEX. HEAD SCREW 5
106 0301 2358 00 PLAIN WASHER 5
108 1604 2473 00 SUPPORT 5
110 0147 1377 03 HEX. HEAD SCREW 5
112 0301 2344 00 PLAIN WASHER 10
114 0291 1111 00 LOCKNUT 5
116 0226 9920 14 LINK SCREW 5
118 0291 1111 00 LOCKNUT 5
120 1604 2471 00 RETAINER 5
122 0291 1110 00 LOCKNUT 5
124 0147 1343 03 HEX. HEAD SCREW 5
200 1604 2582 00 GASKET 2
202 1604 2583 00 HOSE ASSEMBLY 1
- 269 -
- 270 -
www.atlascopco.com