Professional Documents
Culture Documents
Service Bulletin A330-53-3166
Service Bulletin A330-53-3166
Service Bulletin A330-53-3166
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE
Tel : (33) 5 61 93 33 33
Telex : AIRBU 530526F
Fax : (33) 5 61 93 42 51
ATA SYSTEM : 53
ADDITIONAL WORK
Additional work is required by this revision for aircraft included in Config. 02 and modified by initial
issue of this Service Bulletin.
REASON
- Add additional work for aircraft included in Config. 02 and modified by initial issue (the flange of
frame 47 must be modified for these aircraft) ;
CHANGES
SUMMARY :
- REASON/DESCRIPTION/OPERATIONAL CONSEQUENCES
. Modification added.
- EFFECTIVITY
- CONCURRENT REQUIREMENTS
- MANPOWER
. Total manhours and elapsed time added for Config. 02 and additional work tasks.
- MATERIAL INFORMATION
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
PLANNING INFORMATION :
- EFFECTIVITY
- CONCURRENT REQUIREMENTS
- REASON
- Objective/Action
- DESCRIPTION
. 1.D. Description of accomplishment instructions added for Config. 02 and additional work task.
- MANPOWER
- REFERENCES
. 1.J. Reference to Service Bulletin No. A330-53-3030, No. A330-53-3131 and No. A330-53-3182
added.
MATERIAL INFORMATION :
. 2.A.(2) Price of the Kits updated. Kits lead time of 90 days becomes 180 days. Kit 533166A06R01
added.
- LIST OF COMPONENTS
- Consumable Materials
.
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
ACCOMPLISHMENT INSTRUCTIONS :
- Preparation
- Standard Practices
- MODIFICATION
- TESTS
- CLOSE-UP
- ILLUSTRATIONS
FILING INSTRUCTIONS
This Service Bulletin has been generated electronically and is reissued as a complete document.
Replace the complete document.
No previous revisions.
REVISION SEQUENCE
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE
Tel : (33) 5 61 93 33 33
Telex : AIRBU 530526F
Fax : (33) 5 61 93 42 51
ATA SYSTEM : 53
REASON/DESCRIPTION/OPERATIONAL CONSEQUENCES
Several Asian A330 / A340 operators have reported corrosion at the lower bilge of belly fairing sub-structure.
The most affected area is between FR39.1 and FR47 Y +/-1065, but corrosion has also been found at
further locations (e.g. aft of the Main Landing Gear panels). The corrosion is generally located around
anchor-nut holes.
Various design improvements have been introduced, further drain holes on belly fairing panels have been
added with Mod. No. 45814S13889 (FUSELAGE - CENTER FUSELAGE - IMPROVE BELLY FAIRING
DRAINAGE). Modifications No. 48404 (FUSELAGE - ELIMINATE CORROSION ON EXTERNAL FUSELAGE
SKIN UNDER THE BELLY FAIRING) and 50435S16586 (FUSELAGE - CENTER FUSELAGE - IMPROVE
BELLY FAIRING DRAINAGE) have been launched to avoid contamination with fluids from the fuselage drain
valves and the air conditioning packs, by installing funnels and drain pipes.
The latest enhancement has been provided through a serial modification No. 50675S16662 (FUSELAGE -
FAIRINGS - USE OF TITANIUM ON 31 BELLY FAIRING PARTS) on A330 / A340-200/300 aircraft, which
replaces tee flanges more frequently affected by corrosion with titanium ones. The concerned parts are
in the belly fairing bilge area.
According to decision taken during last symposium (May 2006), this Service Bulletin proposes to apply the
modification No. 50675S16662 and 58557S19522 (FUSELAGE - FAIRINGS - USE OF TITANIUM ON 31
BELLY FAIRING PARTS) on in-service aircraft. Means replacement of all aluminium tee flanges by titanium
ones in a one shot embodiment.
Nevertheless, individual replacement of each tee flange on case by case is still possible according procedure
detailed in SIL 53-092.
Modifying the lower bilge of the belly fairing between FR37.4 and FR53.8 by changing the aluminium tee
flanges by titanium ones. For aircraft on which Mod. No. 46752S14512 (FUSELAGE - BELLY FAIRING -
REINFORCE FR53.4 / 53.6 LH AND RH) is not embodied, this Service Bulletin must be accomplished
simultaneously with the Service Bulletin A330-53-3108, Mod. No. 46752S14512. In this case, when
operators accomplish the Service Bulletin A330-53-3108, they have to install directly the titanium flanges at
FR53.4 as described in the accomplishment instructions of the Service Bulletin A330-53-3166 instead of
the aluminium flanges.
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
Accomplishment of this Service Bulletin will avoid corrosion and structural damages in the belly fairing bilge
area and concerned parts replacement.
EVALUATION TABLE
MODIFICATION CLASSIFICATION
MAJOR None
50675S16662
MINOR
58557S19522
As per EASA IR 21, a minor change is one that has no appreciable effect on the mass, balance, structural
strength, reliability, operational characteristics affecting the airworthiness of the product. All other changes
are major changes.
EFFECTIVITY
AAR ACA ACI ADH AFR AIB ALK BEL BMA CAL CPA CRL CYP DLH EDW EIN EVA FWI GFA GIA GRL
HDA HFY HVN I2L IAC IWD IYE JST KAL KKK LTU LVG MAS MON MSR NWA OBS PAL QAF QFA QTR
SAS STZ SWR TAM TAP TCX THA THY TSC UAE USA VKG VLK XAX XLF
NOTE : This modification is embodied before delivery on aircraft MSN 0642 and subsequent.
NOTE : The original issue of this Service Bulletin has been validated on A330 aircraft MSN 0234.
CONCURRENT REQUIREMENTS
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment of the following
Service Bulletin or the equivalent production modification:
For access reason, this Service Bulletin can be done at the same time as :
REFERENCES/REPERCUSSIONS
TFU : 53.35.00.013
OEB : None
AOT : None
SIL : 53-092
OTHERS : None
AIRCRAFT : YES
EQUIPMENT : NO
HARD : NO
SOFT : NO
OBRM : NO
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
MANPOWER
MATERIAL INFORMATION
AIRCRAFT DATA
Config. 01
Kit 533166A01R01
Kit 533166A02R00
Kit 533166A03R00
Kit 533166A04R00
Flanges, Receptacles.
Kit 533166A05R00
Flanges, Receptacles.
Config. 02
Kit 533166A01R01
Kit 533166A02R00
Kit 533166A03R00
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
Kit 533166A04R00
Flanges, Receptacles.
Kit 533166A05R00
Flanges, Receptacles.
Kit 533166A06R01
Kit 533166A06R01
APPENDICES
None
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE
Tel : (33) 5 61 93 33 33
Telex : AIRBU 530526F
Fax : (33) 5 61 93 42 51
ATA SYSTEM : 53
This document contains AIRBUS PROPRIETARY INFORMATION and shall at all times remain the property
of AIRBUS; no intellectual property right or licence is granted by AIRBUS in connection with any information
contained in it. It is delivered on the express condition that said document and the information contained in
it shall be treated as confidential, shall not be used for any purpose other than that for which it is hereby
delivered. It shall not be disclosed in whole or in part to third parties and shall not be duplicated in any
manner (except for the purposes of performing the tasks described hereunder and provided that any recipient
of such document shall comply with the conditions herein), without AIRBUS’ prior written consent.
1. PLANNING INFORMATION
A. EFFECTIVITY
(1) Models
330-202 330-203 330-223 330-243 330-301 330-302 330-303 330-321 330-322 330-323
330-341 330-342 330-343
(2) Aircraft
0012 0017 0030 0037 0042 0045 0050 0054 0055 0059 0060 0062 0064-0067
0069-0073 0077 0082 0083 0086 0087 0095 0096 0098-0100 0102 0106 0107
0109-0113 0116 0118-0122 0127 0132 0138 0140 0143 0144 0148 0153 0155 0162
0165 0171 0172 0177 0181 0183 0184 0188 0189 0191 0195 0198 0200 0203 0205
0206 0209 0211 0219 0222-0224 0226 0229-0232 0234 0238 0240 0241 0244
0247-0251 0253-0256 0258 0259 0261 0262 0265-0267 0269 0271 0272 0275-0277
0279 0281 0283-0288 0290 0291 0293-0296 0299-0301 0303 0305 0306 0308 0309
0311-0317 0320 0322-0324 0326 0328 0330 0333 0334 0337-0340 0342-0346
0348-0351 0353 0356-0358 0361 0362 0364-0366 0368-0370 0372 0375 0380 0382
0384 0386 0388 0389 0392 0393 0396-0398 0400 0401 0403-0405 0407-0409 0412
0418-0423 0425 0427 0428 0432 0437 0439 0441 0443 0444 0448 0451 0452
0454-0456 0458 0461-0463 0465 0466 0469 0472 0473 0476 0477 0479-0481 0484
0486 0487 0489-0491 0493 0494 0496-0498 0500-0513 0515 0516 0518 0519 0521
0522 0524-0527 0529 0530 0532 0533 0535 0536 0539 0542 0548-0553 0555 0558
0564 0565 0567 0568 0570 0571 0573 0574 0576 0578 0579 0581 0584 0587 0588
0591 0593 0595 0597 0600 0602 0603 0605 0607 0609 0610 0612 0614 0616 0618
0620 0621 0623 0625 0627 0629 0631-0638 0640 0641
The Operator/MSN relationship is provided for information only and is correct at the
time of issue in accordance with the information available to AIRBUS. Any future
changes resulting from transfer of an aircraft from one operator to another will not be
reflected in this list unless the Service Bulletin is revised for another reason.
OPERATOR MSN
AAR 0640
AFR 0422 0443 0448 0458 0465 0481 0498 0500 0502 0503 0516
0519 0567 0584
AIB 0042
CPA 0012 0017 0071 0083 0099 0102 0109 0113 0118 0121 0155 0244
0386 0389 0393 0418 0420 0421 0423 0439 0539 0548 0565
EDW 0369
OPERATOR MSN
GFA 0276 0281 0286 0287 0334 0340 0527 0529 0532
GRL 0230
HDA 0098 0106 0132 0177 0234 0405 0407 0479 0512 0581
HFY 0096
IWD 0072
KAL 0162 0172 0206 0219 0222 0226 0241 0256 0258 0267 0338 0350
0351 0368 0425 0428 0484 0490 0550
LTU 0120 0127 0171 0403 0432 0444 0454 0469 0476 0493
MAS 0067 0069 0073 0077 0095 0100 0107 0110 0116 0119 0143
0290 0296 0300
NWA 0524 0533 0542 0549 0552 0578 0588 0591 0609 0614 0618
0620 0621 0631 0633
OBS 0461
QTR 0441 0473 0489 0511 0521 0571 0612 0616 0623 0637 0638
OPERATOR MSN
STZ 0324
TAM 0232 0238 0247 0259 0361 0466 0472 0477 0486
THA 0050 0060 0062 0064 0065 0066 0112 0122 0209 0224 0231 0346
UAE 0248 0251 0283 0293 0295 0314 0316 0326 0328 0345 0348 0365
0372 0382 0384 0392 0396 0409 0437 0451 0452 0455 0462 0491
0494 0509 0518 0525 0536
USA 0315 0323 0333 0337 0342 0370 0375 0380 0388
VLK 0070
XAX 0054
The Kits and configurations applicable to these MSNs are given at the end of this list
0012 0017 0030 0037 0042 0045 0050 0054-0055 0059-0060 0062 0064-0065
0067 0069-0071 0073 0077 0082-0083
533166A01R01 1 01 (01)
02
533166A02R00 1 01 (01)
02
533166A03R00 1 01 (01)
02
533166A04R00 1 01 (01)
02
533166A05R00 1 01 (01)
02
533166A06R01 1 02 (02)
The Kits and configurations applicable to these MSNs are given at the end of this list
533166A01R01 1 01
533166A02R00 1 01
533166A03R00 1 01
533166A04R00 1 01
533166A05R00 1 01
NOTE : The original issue of this Service Bulletin has been validated on A330
aircraft MSN 0234.
(3) Spares
None
B. CONCURRENT REQUIREMENTS
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment of the
following Service Bulletin or the equivalent production modification:
For access reason, this Service Bulletin can be done at the same time as :
C. REASON
(1) History
Several Asian A330 / A340 operators have reported corrosion at the lower bilge of belly
fairing sub-structure. The most affected area is between FR39.1 and FR47 Y +/-1065, but
corrosion has also been found at further locations (e.g. aft of the Main Landing Gear
panels). The corrosion is generally located around anchor-nut holes.
Various design improvements have been introduced, further drain holes on belly fairing
panels have been added with Mod. No. 45814S13889 (FUSELAGE - CENTER FUSELAGE
- IMPROVE BELLY FAIRING DRAINAGE). Modifications No. 48404 (FUSELAGE
- ELIMINATE CORROSION ON EXTERNAL FUSELAGE SKIN UNDER THE BELLY
FAIRING) and 50435S16586 (FUSELAGE - CENTER FUSELAGE - IMPROVE BELLY
FAIRING DRAINAGE) have been launched to avoid contamination with fluids from the
fuselage drain valves and the air conditioning packs, by installing funnels and drain pipes.
The latest enhancement has been provided through a serial modification No. 50675S16662
(FUSELAGE - FAIRINGS - USE OF TITANIUM ON 31 BELLY FAIRING PARTS) on A330 /
A340-200/300 aircraft, which replaces tee flanges more frequently affected by corrosion
with titanium ones. The concerned parts are in the belly fairing bilge area.
(2) Objective/Action
According to decision taken during last symposium (May 2006), this Service Bulletin
proposes to apply the modification No. 50675S16662 and 58557S19522 (FUSELAGE -
FAIRINGS - USE OF TITANIUM ON 31 BELLY FAIRING PARTS) on in-service aircraft.
Means replacement of all aluminium tee flanges by titanium ones in a one shot embodiment.
Nevertheless, individual replacement of each tee flange on case by case is still possible
according procedure detailed in SIL 53-092.
Modifying the lower bilge of the belly fairing between FR37.4 and FR53.8 by changing the
aluminium tee flanges by titanium ones. For aircraft on which Mod. No. 46752S14512
(FUSELAGE - BELLY FAIRING - REINFORCE FR53.4 / 53.6 LH AND RH) is not embodied,
this Service Bulletin must be accomplished simultaneously with the Service Bulletin
A330-53-3108, Mod. No. 46752S14512. In this case, when operators accomplish the
Service Bulletin A330-53-3108, they have to install directly the titanium flanges at FR53.4
as described in the accomplishment instructions of the Service Bulletin A330-53-3166
instead of the aluminium flanges.
(3) Advantages
Accomplishment of this Service Bulletin will avoid corrosion and structural damages in the
belly fairing bilge area and concerned parts replacement.
D. DESCRIPTION
(1) Config. 01
(a) Remove the panels between FR47 and the Main Landing Gear for access.
(b) Replace the flanges in the belly fairing between FR37.4 and FR39.1.
(c) Replace the flanges in the belly fairing between FR39.1 and FR44.
(d) Replace the flanges in the belly fairing between FR44 and FR47.
(f) Replace the flanges in the belly fairing between FR53.2 and FR53.8.
(g) Install the panels between FR47 and the Main Landing Gear.
(2) Config. 02
(a) Remove the panels between FR47 and the Main Landing Gear for access.
(b) Replace the flanges in the belly fairing between FR37.4 and FR39.1.
(c) Replace the flanges in the belly fairing between FR39.1 and FR44.
(d) Replace the flanges in the belly fairing between FR44 and FR47.
(f) Replace the flanges in the belly fairing between FR53.2 and FR53.8.
(g) Install the panels between FR47 and the Main Landing Gear.
(a) Preparation
(b) Remove the panels between FR47 and the Main Landing Gear for access.
(d) Install the panels between FR47 and the Main Landing Gear.
(e) Test
(f) Close up
E. COMPLIANCE
(1) Classification
Desirable
F. APPROVAL
If an aircraft listed in the effectivity has a modification or repair embodied that is not of AIRBUS
origin, and which affects the content of this Service Bulletin, the operator is responsible for
obtaining approval by its airworthiness authority for any adaptation necessary before incorporation
of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to do the
work. These estimates assume that the work will be done by experienced personnel, and may
need to be revised upwards to suit operator’s circumstances. The estimates do not include the
time to prepare, plan or inspect the work. Manufacture and procurement of parts and tools, drying
times for paints, sealants, etc, and general administration work are also not included.
Test 2.0
Close-up 14.0
Close-up 2.0
For aircraft models 330-301, 330-302, 330-303, 330-321, 330-322, 330-323, 330-341, 330-342
and 330-343
Not changed
J. REFERENCES
K. PUBLICATIONS AFFECTED
L. INTERCHANGEABILITY/MIXABILITY
Not applicable
2. MATERIAL INFORMATION
(1) Material
Customers with aircraft shown in the effectivity of this Service Bulletin should send a
purchase order to AIRBUS. Quote the number of this Service Bulletin. The address is :
AIRBUS
SPARES SUPPORT AND SERVICES
Weg beim Jaeger 150
D-22335 HAMBURG
GERMANY
Kit 533166A01R01
The Kit availability given above is the standard lead time from the date of your purchase
order. If you require the Kit(s) before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements.
The sales terms (costs and availability) are estimated in relation to economic conditions
at the issue date of the Service Bulletin.
Kit 533166A02R00
The Kit availability given above is the standard lead time from the date of your purchase
order. If you require the Kit(s) before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements.
The sales terms (costs and availability) are estimated in relation to economic conditions
at the issue date of the Service Bulletin.
Kit 533166A03R00
The Kit availability given above is the standard lead time from the date of your purchase
order. If you require the Kit(s) before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements.
The sales terms (costs and availability) are estimated in relation to economic conditions
at the issue date of the Service Bulletin.
Kit 533166A04R00
The Kit availability given above is the standard lead time from the date of your purchase
order. If you require the Kit(s) before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements.
The sales terms (costs and availability) are estimated in relation to economic conditions
at the issue date of the Service Bulletin.
Kit 533166A05R00
The Kit availability given above is the standard lead time from the date of your purchase
order. If you require the Kit(s) before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements.
The sales terms (costs and availability) are estimated in relation to economic conditions
at the issue date of the Service Bulletin.
Kit 533166A06R01
The Kit availability given above is the standard lead time from the date of your purchase
order. If you require the Kit(s) before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements.
The sales terms (costs and availability) are estimated in relation to economic conditions
at the issue date of the Service Bulletin.
NOTE : Config. 02
Operators that have already received the Kit 533166A03R00 at any revision
must order the additional Kit 533166A06R01.
AIRBUS will provide a 45 percent reduction to the applicable sales prices given in paragraph
2A(2) for orders placed before Dec 31/2012.
C. LIST OF COMPONENTS
Kit 533166A01R01
ITEM NEW PART No. QTY UM KEYWORD ITEM OLD PART No. INT INST DISP
1 F5331426000095 1 Flange
2 F5331426100095 1 Flange
3 F5331426200095 1 Flange
4 F5331426300095 1 Flange
5 F5331426400095 1 Flange
6 F5331426600095 1 Flange
8 F5331426520095 1 Web
52 ASNA0082-203 6 Rivet
53 ASNA0082-204 2 Rivet
63 ASNA2050DXJ4020 11 Rivet
65 ASNA2051DCJ3215 4 Rivet
67 ASNA2531-2 26 Nut
69 EN6115V2-2 5 Bolt
70 EN6115V2-3 21 Bolt
73 NAS1791A3-2 7 RECEPTCL
74 NAS1791A3-3 110 RECEPTCL
80 NAS1919M05S05W 6 Rivet
82 NAS1921M05S03W 4 Rivet
84 NSA5050-3 3 Nut
86 NSA5414N24-12A 234 Rivet
88 NSA5415V40-18A 323 Rivet
NOTE : Refer to the AIRBUS Standards Manual (SM) if you find part numbers of hardware
components in the related kit(s) which you cannot identify in the LIST OF
COMPONENTS of this Service Bulletin. The SM will give you the correct part number
to part number relationship.
Kit 533166A02R00
ITEM NEW PART No. QTY UM KEYWORD ITEM OLD PART No. INT INST DISP
9 F5331531200095 1 Flange
10 F5331532900095 1 Flange
11 F5331533200095 1 Flange
13 F5331537300095 1 Flange
14 F5331537400095 1 Flange
16 F5331542300095 1 Flange
17 F5331542400095 1 Flange
18 F5331547300095 1 Flange
19 F5331547400095 1 Flange
22 F5331556100695 1 Web
50 ABS0112-24-02C 40 Rivet
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
ITEM NEW PART No. QTY UM KEYWORD ITEM OLD PART No. INT INST DISP
63 ASNA2050DXJ4020 17 Rivet
68 EN6092-01 216 RECEPTCL
74 NAS1791A3-3 64 RECEPTCL
79 NAS1919M05S04W 2 Rivet
86 NSA5414N24-12A 520 Rivet
88 NSA5415V40-18A 504 Rivet
NOTE : Refer to the AIRBUS Standards Manual (SM) if you find part numbers of hardware
components in the related kit(s) which you cannot identify in the LIST OF
COMPONENTS of this Service Bulletin. The SM will give you the correct part number
to part number relationship.
Kit 533166A03R00
ITEM NEW PART No. QTY UM KEYWORD ITEM OLD PART No. INT INST DISP
7 F5331518700695 1 Splice
12 F5331534400095 1 Flange 02
15 F5331539200095 1 Flange
20 F5331552500095 1 Flange
21 F5331553200095 1 Flange
23 F5331562120095 1 Shim
24 F5331562220095 1 Shim
25 F5331568400495 1 Splice 02
51 ABS0112-24-04C 20 Rivet
54 ASNA0082-205 2 Rivet
55 ASNA0082B203 1 Rivet
56 ASNA0113-40CA 8 Washer
66 ASNA2051DXJ4020 26 Rivet
68 EN6092-01 86 RECEPTCL
72 NAS1791A3-1 3 Nut
73 NAS1791A3-2 25 RECEPTCL
74 NAS1791A3-3 5 RECEPTCL
75 NAS1792A3-2 1 RECEPTCL
76 NAS1919M05S03 25 Rivet
77 NAS1919M05S03W 6 Rivet
78 NAS1919M05S04 3 Rivet
81 NAS1921M05S03 8 Rivet
82 NAS1921M05S03W 2 Rivet
86 NSA5414N24-12A 232 Rivet
88 NSA5415V40-18A 120 Rivet
89 NAS1792A3-1 7 Nut
90 NSA5414V40-18A 22 Rivet
NOTE(01) Refer to the AIRBUS Standards Manual (SM) if you find part numbers of hardware
components in the related kit(s) which you cannot identify in the LIST OF
COMPONENTS of this Service Bulletin. The SM will give you the correct part number
to part number relationship.
NOTE(02) For Aircraft in Config. 02 , the flange item 12 and the splice item 25 are replaced by
the flange item 139 and the splice item 140 from Kit 533166A06R01.
Kit 533166A04R00
ITEM NEW PART No. QTY UM KEYWORD ITEM OLD PART No. INT INST DISP
26 F5331733000095 1 Flange
27 F5331733100095 1 Flange
28 F5331733100195 1 Flange
73 NAS1791A3-2 159 RECEPTCL
79 NAS1919M05S04W 104 Rivet
86 NSA5414N24-12A 318 Rivet
88 NSA5415V40-18A 134 Rivet
NOTE : Refer to the AIRBUS Standards Manual (SM) if you find part numbers of hardware
components in the related kit(s) which you cannot identify in the LIST OF
COMPONENTS of this Service Bulletin. The SM will give you the correct part number
to part number relationship.
Kit 533166A05R00
ITEM NEW PART No. QTY UM KEYWORD ITEM OLD PART No. INT INST DISP
29 F5331842000095 1 Flange
30 F5331842000195 1 Flange
31 F5331842100095 1 Flange
32 F5331842200095 1 Flange
33 F5331842300095 1 Flange
34 F5331842400095 1 Flange
35 F5331842400195 1 Flange
36 F5331842500095 1 Flange
37 F5331842600095 1 Flange
50 ABS0112-24-02C 94 Rivet
64 ASNA2051DCJ2412 14 Rivet
67 ASNA2531-2 30 Nut
70 EN6115V2-3 22 Bolt
71 EN6115V2-5 8 Bolt
73 NAS1791A3-2 53 RECEPTCL
74 NAS1791A3-3 180 RECEPTCL
77 NAS1919M05S03W 6 Rivet
86 NSA5414N24-12A 358 Rivet
88 NSA5415V40-18A 467 Rivet
91 NSA5415V32-15A 6 Rivet
126 NAS1919M06S03W 46 Rivet
127 NAS1919M06S04W 4 Rivet
NOTE : Refer to the AIRBUS Standards Manual (SM) if you find part numbers of hardware
components in the related kit(s) which you cannot identify in the LIST OF
COMPONENTS of this Service Bulletin. The SM will give you the correct part number
to part number relationship.
Kit 533166A06R01
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
ITEM NEW PART No. QTY UM KEYWORD ITEM OLD PART No. INT INST DISP
7 F5331518700695 1 Splice
53 ASNA0082-204 5 Rivet
54 ASNA0082-205 4 Rivet
66 ASNA2051DXJ4020 12 Rivet
68 EN6092-01 28 RECEPTCL
73 NAS1791A3-2 32 RECEPTCL
82 NAS1921M05S03W 4 Rivet
86 NSA5414N24-12A 120 Rivet
88 NSA5415V40-18A 50 Rivet
139 F5331540000495 1 Flange
140 F5331567620000 1 Splice
NOTE : Refer to the AIRBUS Standards Manual (SM) if you find part numbers of hardware
components in the related kit(s) which you cannot identify in the LIST OF
COMPONENTS of this Service Bulletin. The SM will give you the correct part number
to part number relationship.
NOTE(02) For Aircraft in Config. 02 , the flange item 139 and the splice item 140 replace the
flange item 12 and the splice item 25 from Kit 533166A03R00.
(2) Components
None
None
None
G. SPECIAL TOOLS
None
3. ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL
WARNING : MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
(1) Preparation
(a) Config. 01
1 Make sure that the aircraft is electrically grounded (Refer to AMM 12-34-24,
Page block 201).
2 Open the FWD cargo-compartment door 821 (Refer to AMM 52-30-00, Page
block 201).
3 Open the MLG doors (Refer to AMM 32-12-00, Page block 201).
5 Remove the access door of the CLG door ground opening handle (149BB)
(Refer to AMM 52-42-32, Page block 401).
6 Remove the access door of the MLG door ground opening handle (149CB)
(Refer to AMM 52-42-32, Page block 401).
7 Remove the air outlet flap assembly (Refer to AMM 53-35-42, Page block 401).
8 Remove the belly-fairing access panels (Refer to AMM 53-35-13, Page block
401 and AMM 06-41-53, Page block 001) :
- For Kit 533166A01R01: access panels 191AB, 191BB, 191DB and 192BB.
9 Remove the LH and RH belly fairing access panels behind MLG doors (Refer
to AMM 53-35-13, Page block 401).
(b) Config. 02
1 Make sure that the aircraft is electrically grounded (Refer to AMM 12-34-24,
Page block 201).
2 Open the FWD cargo-compartment door 821 (Refer to AMM 52-30-00, Page
block 201).
3 Open the MLG doors (Refer to AMM 32-12-00, Page block 201).
5 Remove the access door of the CLG door ground opening handle (149BB)
(Refer to AMM 52-42-32, Page block 401).
6 Remove the access door of the MLG door ground opening handle (149CB)
(Refer to AMM 52-42-32, Page block 401).
7 Remove the air outlet flap assembly (Refer to AMM 53-35-42, Page block 401).
8 Remove the belly-fairing access panels (Refer to AMM 53-35-13, Page block
401 and AMM 06-41-53, Page block 001) :
- For Kit 533166A01R01: access panels 191AB, 191BB, 191DB and 192BB.
9 Remove the LH and RH belly fairing access panels behind MLG doors (Refer
to AMM 53-35-13, Page block 401).
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
(a) For the specification of the material numbers (Mat No.), refer to CML.
(b) Clean the surfaces to seal with solvent Solvent General Purpose (Mat. No. 11-026).
- The length of these rivets can be adapted according to what is found in stock.
Operator will end up cutting to length the rivets before installation.
NOTE : Special care has to be taken for monel rivets as they are more difficult
to cut than aluminium rivets. Cutting must be clean and deburred so
that the rivets do not crack during squeezing.
(h) Torque the standard threaded fasteners (Refer to AMM 20-21-00, Page block 001).
(i) Install the fasteners with Corrosion Inhibiting Brush Consistency (Mat. No. 09-013)
(wet assembly).
(j) Do the electrical bonding (Refer to AMM 20-28-11, Page block 001) with Pure
Mineral Vaseline or Petro-Latum (Mat. No. 04-012) and Electrical Bonding Coating
(Blue Color) (Mat. No. 07-001).
(k) Apply Corrosion Inhibitive interfay Sealant (Mat. No. 09-005) or Polysulphide
Sealant for Interfay (Mat. No. 09-043) to interfaces of structure and new parts as
specified in SRM 51-24-00.
(l) Do a bead of Corrosion Inhibiting Brush Consistency (Mat. No. 09-013B) on the new
parts as specified in SRM 51-24-00.
(m) Renew the protective finish with Low Voc Anti Corrosion Primer (Mat. No. 16-006D)
and Internal Top Coat (Mat. No. 16-002C).
B. MODIFICATION
(1) Config. 01
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
(a) Remove the panels between FR47 and the Main Landing Gear for access.
Refer to Figure 1, Sheets 1 and 2
(b) Replace the flanges in the belly fairing between FR37.4 and FR39.1.
Refer to Kit 533166A01R01
Refer to Figure 2, Sheets 1 thru 7
a Remove :
102 Rivet Item (63) Discard
1 Flange Item (1)
b On bench, transfer the existing holes of the receptacles from the old flange
item (1) to the new flange item 1 to a diameter comprised between 6.5 mm
(0.256 in.) and 6.6 mm (0.260 in.).
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
d On bench, drill the new flange item 1 to match the holes with the receptacles
item 74.
f On bench, install :
36 Receptacle NAS1791A3-3 Item 74
72 Rivet NSA5414N24-12A Item 86
h Drill the flange item 1 to match the holes with the structure.
j Install :
1 Flange F5331426000095 Item 1
102 Rivet NSA5415V40-18A Item 88
a Remove :
19 Rivet Item (63) Discard
1 Flange Item (4)
b On bench, transfer the existing holes of the receptacles from the old flange
item (4) to the new flange item 4 to a diameter comprised between 6.5 mm
(0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331426300095 Item 4
d On bench, drill the new flange item 4 to match the holes with the receptacles
item 74.
f On bench, install :
5 Receptacle NAS1791A3-3 Item 74
10 Rivet NSA5414N24-12A Item 86
h Drill the flange item 4 to match the holes with the structure.
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
j Install :
1 Flange F5331426300095 Item 4
19 Rivet NSA5415V40-18A Item 88
a Remove :
49 Rivet Item (63) Discard
1 Flange Item (2)
6 Rivet Item (52) Discard
5 Rivet Item (58) Discard
5 Bush Item (57) Discard
2 Rivet Item (53) Discard
3 Bolt Item (83) Retain
3 Nut Item (84) Discard
1 Web Item (8)
4 Rivet Item (65) Discard
1 Support Item (105) Retain
b On bench, temporarily put in position the new flange item 6 on the new
web item 8.
1 Flange F5331426600095 Item 6
1 Web F5331426520095 Item 8
c On bench, drill the flange item 6 to match the holes of the web item 8.
f On bench, transfer the existing holes of the receptacles from the old flange
item (2) and the old web item (8) to the new flanges items 2 and 6 to a
diameter comprised between 6.5 mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331426100095 Item 2
h On bench, drill the new flanges items 2 and 6 to match the holes with
the receptacles item 74.
j On bench, install :
17 Receptacle NAS1791A3-3 Item 74
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
k Temporarily, put in position the flange item 2 and the web item 8 to the
structure.
l Drill the flange item 2 and the web item 8 to match the holes with the
structure.
n Install :
1 Flange F5331426100095 Item 2
1 Web F5331426520095 Item 8
11 Rivet ASNA2050DXJ4020 Item 63
38 Rivet NSA5415V40-18A Item 88
6 Rivet ASNA0082-203 Item 52
5 Bolt EN6115V2-2 Item 69
5 Nut ASNA2531-2 Item 67
2 Rivet ASNA0082-204 Item 53
3 Bolt Item (83)
3 Nut NSA5050-3 Item 84
1 Support Item (105)
4 Rivet ASNA2051DCJ3215 Item 65
a Remove :
6 Rivet Item (64) Discard
3 Receptacle Item (73) Discard
9 Rivet Item (59) Discard
9 Bush Item (57) Discard
1 Gusset Item (100) Retain
2 Gusset Item (102) Retain
64 Rivet Item (63) Discard
3 Rivet Item (80) Discard
4 Rivet Item (82) Discard
1 Flange Item (3)
b On bench, transfer the existing holes of the receptacles from the old flange
item (3) to the new flange item 3 to a diameter comprised between 6.5 mm
(0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331426200095 Item 3
d On bench, drill the new flange item 3 to match the holes with the receptacles
item 74.
f On bench, install :
24 Receptacle NAS1791A3-3 Item 74
48 Rivet NSA5414N24-12A Item 86
h Drill the flange item 3 to match the holes with the structure.
j Install :
1 Flange F5331426200095 Item 3
64 Rivet NSA5415V40-18A Item 88
3 Rivet NAS1919M05S05W Item 80
4 Rivet NAS1921M05S03W Item 82
1 Gusset Item (100)
2 Gusset Item (102)
9 Bolt EN6115V2-3 Item 70
9 Nut ASNA2531-2 Item 67
k Drill the flange item 3 to match the holes of the gussets items (100) and
(102).
l Install :
3 Receptacle NAS1791A3-2 Item 73
6 Rivet NSA5414N24-12A Item 86
a Remove :
8 Rivet Item (64) Discard
4 Receptacle Item (73) Discard
12 Rivet Item (59) Discard
12 Bush Item (57) Discard
1 Gusset Item (101) Retain
1 Gusset Item (102) Retain
2 Gusset Item (104) Retain
64 Rivet Item (63) Discard
3 Rivet Item (80) Discard
1 Flange Item (5)
NOTE : If necessary, remove items (57), (59) (101), (102) and (104).
b On bench, transfer the existing holes of the receptacles from the old flange
item (5) to the new flange item 5 to a diameter comprised between 6.5 mm
(0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331426400095 Item 5
d On bench, drill the new flange item 5 to match the holes with the receptacles
item 74.
f On bench, install :
28 Receptacle NAS1791A3-3 Item 74
56 Rivet NSA5414N24-12A Item 86
h Drill the flange item 5 to match the holes with the structure.
j Install :
1 Flange F5331426400095 Item 5
64 Rivet NSA5415V40-18A Item 88
3 Rivet NAS1919M05S05W Item 80
1 Gusset Item (101)
1 Gusset Item (102)
2 Gusset Item (104)
12 Bolt EN6115V2-3 Item 70
12 Nut ASNA2531-2 Item 67
k Drill the flange item 5 to match the holes of the gussets items (101), (102)
and (104).
l Install :
4 Receptacle NAS1791A3-2 Item 73
8 Rivet NSA5414N24-12A Item 86
(c) Replace the flanges in the belly fairing between FR39.1 and FR44.
Refer to Kit 533166A02R00
Refer to Figure 3, Sheets 1 thru 8
a Remove :
72 Rivet Item (63) Discard
1 Flange Item (9)
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
b On bench, transfer the existing holes of the receptacles from the old flange
item (9) to the new flange item 9 to a diameter comprised between 6.5 mm
(0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331531200095 Item 9
d On bench, drill the new flange item 9 to match the holes with the receptacles
items 68 and 74.
f On bench, install :
30 Receptacle EN6092-01 Item 68
60 Rivet NSA5414N24-12A Item 86
20 Receptacle NAS1791A3-3 Item 74
40 Rivet ABS0112-24-02C Item 50
h Drill the flange item 9 to match the holes with the structure.
j Install :
1 Flange F5331531200095 Item 9
72 Rivet NSA5415V40-18A Item 88
a Remove :
4 Rivet Item (123) Discard
1 Web Item (22) Discard
c Drill the web item 22 to match the holes with the structure.
e Install :
1 Web F5331556100695 Item 22
4 Rivet NSA5415V40-18A Item 88
a Remove :
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
b On bench, transfer the existing holes of the receptacles from the old flange
item (10) to the new flange item 10 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331532900095 Item 10
d On bench, drill the new flange item 10 to match the holes with the
receptacles item 68.
f On bench, install :
32 Receptacle EN6092-01 Item 68
64 Rivet NSA5414N24-12A Item 86
h Drill the flange item 10 to match the holes with the structure.
j Install :
1 Flange F5331532900095 Item 10
48 Rivet NSA5415V40-18A Item 88
a Remove :
47 Rivet Item (63) Discard
2 Rivet Item (79) Discard
1 Support Item (124) Retain
1 Flange Item (11)
b On bench, transfer the existing holes of the receptacles from the old flange
item (11) to the new flange item 11 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331533200095 Item 11
d On bench, drill the new flange item 11 to match the holes with the
receptacles item 68.
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
f On bench, install :
32 Receptacle EN6092-01 Item 68
64 Rivet NSA5414N24-12A Item 86
h Drill the flange item 11 to match the holes with the structure.
j Install :
1 Flange F5331533200095 Item 11
1 Support Item (124)
46 Rivet NSA5415V40-18A Item 88
1 Rivet ASNA2050DXJ4020 Item 63
2 Rivet NAS1919M05S04W Item 79
a Remove :
103 Rivet Item (63) Discard
1 Support Item (125) Retain
1 Flange Item (18)
1 Flange Item (19)
b On bench, transfer the existing holes of the receptacles from the old flanges
items (18) and (19) to the new flanges items 18 and 19 to a diameter
comprised between 6.5 mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331547300095 Item 18
1 Flange F5331547400095 Item 19
d On bench, drill the new flanges items 18 and 19 to match the holes with
the receptacles items 68 and 74.
f On bench, install :
31 Receptacle EN6092-01 Item 68
94 Rivet NSA5414N24-12A Item 86
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
h Drill the flanges items 18 and 19 to match the holes with the structure.
j Install :
1 Flange F5331547300095 Item 18
1 Flange F5331547400095 Item 19
1 Support Item (125)
99 Rivet NSA5415V40-18A Item 88
4 Rivet ASNA2050DXJ4020 Item 63
6 Replace the flange on the central web between FR39.1 and FR44.
Refer to Figure 3, Sheets 1 and 7
a Remove :
136 Rivet Item (63) Discard
1 Flange Item (13)
1 Flange Item (14)
b On bench, transfer the existing holes of the receptacles from the old flanges
items (13) and (14) to the new flanges items 13 and 14 to a diameter
comprised between 6.5 mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331537300095 Item 13
1 Flange F5331537400095 Item 14
d On bench, drill the new flanges items 13 and 14 to match the holes with
the receptacles items 68 and 74.
f On bench, install :
54 Receptacle EN6092-01 Item 68
134 Rivet NSA5414N24-12A Item 86
13 Receptacle NAS1791A3-3 Item 74
h Drill the flanges items 13 and 14 to match the holes with the structure.
j Install :
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
a Remove :
111 Rivet Item (63) Discard
1 Flange Item (16)
1 Flange Item (17)
b On bench, transfer the existing holes of the receptacles from the old flanges
items (16) and (17) to the new flanges items 16 and 17 to a diameter
comprised between 6.5 mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331542300095 Item 16
1 Flange F5331542400095 Item 17
d On bench, drill the new flanges items 16 and 17 to match the holes with
the receptacles items 68 and 74.
f On bench, install :
37 Receptacle EN6092-01 Item 68
104 Rivet NSA5414N24-12A Item 86
15 Receptacle NAS1791A3-3 Item 74
h Drill the flanges items 16 and 17 to match the holes with the structure.
j Install :
1 Flange F5331542300095 Item 16
1 Flange F5331542400095 Item 17
12 Rivet ASNA2050DXJ4020 Item 63
99 Rivet NSA5415V40-18A Item 88
(d) Replace the flanges in the belly fairing between FR44 and FR47.
Refer to Kit 533166A03R00
Refer to Figure 4, Sheets 1 thru 5
a Remove :
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
b On bench, transfer the existing holes of the receptacles from the old shim
item (23) to the new shim item 23 to a diameter comprised between 6.5 mm
(0.256 in.) and 6.6 mm (0.260 in.).
1 Shim F5331562120095 Item 23
c On bench, transfer the existing holes of the receptacles from the old shim
item (24) to the new shim item 24 to a diameter comprised between 6.5 mm
(0.256 in.) and 6.6 mm (0.260 in.).
1 Shim F5331562220095 Item 24
d On bench, transfer the existing holes of the receptacles from the old flange
item (12) to the new flange item 12 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331534400095 Item 12
f On bench, drill the new flange item 12 to match the holes with the
receptacles item 68.
h On bench, install :
j Drill the flange item 12 to match the holes with the structure.
l Install :
1 Flange F5331534400095 Item 12
22 Rivet NSA5415V40-18A Item 88
25 Rivet NAS1919M05S03 Item 76
6 Rivet ASNA2051DXJ4020 Item 66
3 Rivet NAS1919M05S04 Item 78
1 Shim F5331562120095 Item 23
1 Shim F5331562220095 Item 24
1 Rivet ASNA0082B203 Item 55
20 Rivet ABS0112-24-04C Item 51
8 Rivet NAS1921M05S03 Item 81
8 Washer ASNA0113-40CA Item 56
3 Nut NAS1791A3-1 Item 72
7 Nut NAS1792A3-1 Item 89
a Remove :
50 Rivet Item (88) Discard
2 Rivet Item (54) Discard
20 Rivet Item (66) Discard
2 Rivet Item (82) Discard
1 Splice Item (7)
1 Splice Item (25)
1 Flange Item (15)
1 Receptacle Item (89) Discard
2 Receptacle Item (75) Discard
b On bench, transfer the existing holes of the receptacles from the old flange
item (15) to the new flange item 15 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331539200095 Item 15
d On bench, drill the new flange item 15 to match the holes with the
receptacles item 68, 73 and 75.
f On bench, install :
g Temporarily, put in position to the structure the flange item 15 and the
splices item 7 and item 25.
1 Splice F5331518700695 Item 7
1 Splice F5331568400495 Item 25
h Drill the flange item 15, the splices item 7 and item 25 to match the holes
with the structure.
j Install :
1 Flange F5331539200095 Item 15
50 Rivet NSA5415V40-18A Item 88
2 Rivet ASNA0082-205 Item 54
2 Rivet NAS1921M05S03W Item 82
1 Splice F5331518700695 Item 7
1 Splice F5331568400495 Item 25
18 Rivet ASNA2051DXJ4020 Item 66
a Remove :
33 Rivet Item (63) Discard
1 Flange Item (20)
b On bench, transfer the existing holes of the receptacles from the old flange
item (20) to the new flange item 20 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331552500095 Item 20
d On bench, drill the new flange item 20 to match the holes with the
receptacles item 68 and 74.
f On bench, install :
h Drill the flange item 20 to match the holes with the structure.
j Install :
1 Flange F5331552500095 Item 20
33 Rivet NSA5415V40-18A Item 88
a Remove :
22 Rivet Item (66) Discard
15 Rivet Item (63) Discard
1 Flange Item (21)
b On bench, transfer the existing holes of the receptacles from the old flange
item (21) to the new flange item 21 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331553200095 Item 21
d On bench, drill the new flange item 21 to match the holes with the
receptacles item 68 and 74.
f On bench, install :
h Drill the flange item 21 to match the holes with the structure.
j Install :
1 Flange F5331553200095 Item 21
22 Rivet NSA5414V40-18A Item 90
15 Rivet NSA5415V40-18A Item 88
a Remove :
1 Rivet Item (63) Discard
39 Rivet Item (79) Discard
or
b On bench, transfer the existing holes of the receptacles from the old flange
item (27) to the new flange item 27 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331733100095 Item 27
d On bench, drill the new flange item 27 to match the holes with the
receptacles item 73.
f On bench, install :
48 Receptacle NAS1791A3-2 Item 73
96 Rivet NSA5414N24-12A Item 86
h Drill the flange item 27 to match the holes with the structure.
j Install :
1 Flange F5331733100095 Item 27
1 Gusset Item (109)
1 Plate Item (111)
1 Gusset Item (107)
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
or
NOTE(01) If existing, items (107), (109), (111) and (113) were retained
at removal.
NOTE(02) If existing on aircraft, attach the parts items (107), (109), (111)
and (113) with rivets item 79.
a Remove :
6 Rivet Item (63) Discard
34 Rivet Item (79) Discard
or
b On bench, transfer the existing holes of the receptacles from the old flange
item (28) to the new flange item 28 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331733100195 Item 28
d On bench, drill the new flange item 28 to match the holes with the
receptacles item 73.
f On bench, install :
48 Receptacle NAS1791A3-2 Item 73
96 Rivet NSA5414N24-12A Item 86
h Drill the flange item 28 to match the holes with the structure.
j Install :
1 Flange F5331733100195 Item 28
1 Plate Item (116)
1 Plate Item (117)
1 Gusset Item (108)
1 Plate Item (112)
1 Gusset Item (110)
6 Rivet NSA5415V40-18A Item 88
34 Rivet NAS1919M05S04W Item 79
or
NOTE(01) If existing, items (108), (110), (112), (116) and (117) were
retained at removal.
NOTE(02) If existing on aircraft, attach the parts items (108), (110), (112),
(116) and (117) with rivets item 79.
a Remove :
23 Rivet Item (63) Discard
31 Rivet Item (79) Discard
or
b On bench, transfer the existing holes of the receptacles from the old flange
item (26) to the new flange item 26 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331733000095 Item 26
d On bench, drill the new flange item 26 to match the holes with the
receptacles item 73.
f On bench, install :
63 Receptacle NAS1791A3-2 Item 73
126 Rivet NSA5414N24-12A Item 86
h Drill the flange item 26 to match the holes with the structure.
j Install :
1 Flange F5331733000095 Item 26
1 Plate Item (114)
1 Plate Item (115)
23 Rivet NSA5415V40-18A Item 88
31 Rivet NAS1919M05S04W Item 79
or
NOTE(02) If existing on aircraft, attach the parts items (114) and (115)
with rivets item 79.
(f) Replace the flanges in the belly fairing between FR53.2 and FR53.8.
Kit 533166A05R00
Refer to Figure 7, Sheets 1 and 8
a Remove :
4 Rivet Item (64) Discard
2 Receptacle Item (73) Discard
8 Rivet Item (59) Discard
12 Bush Item (57) Discard
1 Gusset Item (118) Retain
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
b On bench, transfer the existing holes of the receptacles from the old flange
item (33) to the new flange item 33 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331842300095 Item 33
d On bench, drill the new flange item 33 to match the holes with the
receptacles item 74.
f On bench, install :
31 Receptacle NAS1791A3-3 Item 74
62 Rivet NSA5414N24-12A Item 86
h Drill the flange item 33 to match the holes with the structure.
j Install :
1 Flange F5331842300095 Item 33
42 Rivet NSA5415V40-18A Item 88
1 Gusset Item (118)
1 Gusset Item (106)
8 Bolt EN6115V2-3 Item 70
12 Nut ASNA2531-2 Item 67
4 Bolt EN6115V2-5 Item 71
k Drill the flange item 33 to match the holes with the gussets items (106)
and (118).
l Install :
2 Receptacle NAS1791A3-2 Item 73
4 Rivet NSA5414N24-12A Item 86
a Remove :
18 Rivet Item (64) Discard
9 Receptacle Item (74) Discard
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
NOTE : To permit the removal of the receptacles item (74), remove and
retain the fasteners and the support existing on the aircraft.
b On bench, transfer the existing holes of the receptacles from the old flange
item (32) to the new flange item 32 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331842200095 Item 32
d On bench, drill the new flange item 32 to match the holes with the
receptacles item 74.
f On bench, install :
22 Receptacle NAS1791A3-3 Item 74
44 Rivet NSA5414N24-12A Item 86
h Drill the flange item 32 to match the holes with the structure.
j Install :
1 Flange F5331842200095 Item 32
17 Rivet NSA5415V40-18A Item 88
2 Bolt EN6115V2-3 Item 70
6 Nut ASNA2531-2 Item 67
4 Bolt EN6115V2-5 Item 71
14 Rivet ASNA2051DCJ2412 Item 64
7 Receptacle NAS1791A3-3 Item 74
k Drill the flange item 32 to match the holes with the existing gussets.
l Install :
2 Receptacle NAS1791A3-3 Item 74
4 Rivet NSA5414N24-12A Item 86
a Remove :
4 Rivet Item (64) Discard
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
b On bench, transfer the existing holes of the receptacles from the old flange
item (34) to the new flange item 34 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331842400095 Item 34
d On bench, drill the new flange item 34 to match the holes with the
receptacles item 74.
f On bench, install :
28 Receptacle NAS1791A3-3 Item 74
56 Rivet NSA5414N24-12A Item 86
h Drill the flange item 34 to match the holes with the structure.
j Install :
1 Flange F5331842400095 Item 34
78 Rivet NSA5415V40-18A Item 88
6 Bolt EN6115V2-3 Item 70
6 Nut ASNA2531-2 Item 67
2 Gusset Item (119)
k Drill the flange item 34 to match the holes with the gussets item (119).
l Install :
2 Receptacle NAS1791A3-2 Item 73
4 Rivet NSA5414N24-12A Item 86
a Remove :
4 Rivet Item (64) Discard
2 Receptacle Item (73) Discard
b On bench, transfer the existing holes of the receptacles from the old flange
item (35) to the new flange item 35 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331842400195 Item 35
d On bench, drill the new flange item 35 to match the holes with the
receptacles item 74.
f On bench, install :
28 Receptacle NAS1791A3-3 Item 74
56 Rivet NSA5414N24-12A Item 86
h Drill the flange item 35 to match the holes with the structure.
j Install :
1 Flange F5331842400195 Item 35
78 Rivet NSA5415V40-18A Item 88
6 Bolt EN6115V2-3 Item 70
6 Nut ASNA2531-2 Item 67
2 Gusset Item (120)
k Drill the flange item 34 to match the holes with the gussets item (120).
l Install :
2 Receptacle NAS1791A3-2 Item 73
4 Rivet NSA5414N24-12A Item 86
a Remove :
6 Rivet Item (61) Discard
or
or
and
b On bench, transfer the existing holes of the receptacles from the old flanges
items (36) and (37) to the new flanges items 36 and 37 to a diameter
comprised between 6.5 mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331842500095 Item 36
1 Flange F5331842600095 Item 37
d On bench, drill the new flanges items 36 and 37 to match the holes with
the receptacles item 74.
f On bench, install :
13 Receptacle NAS1791A3-3 Item 74
26 Rivet NSA5414N24-12A Item 86
h Drill the flanges items 36 and 37 to match the holes with the structure.
j Install :
1 Flange F5331842500095 Item 36
1 Flange F5331842600095 Item 37
50 Rivet NSA5415V40-18A Item 88
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
or
and
or
a Remove :
54 Rivet Item (63) Discard
1 Flange Item (31)
b On bench, transfer the existing holes of the receptacles from the old flange
item (31) to the new flange item 31 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331842100095 Item 31
d On bench, drill the new flange item 31 to match the holes with the
receptacles items 73 and 74.
f On bench, install :
13 Receptacle NAS1791A3-2 Item 73
26 Rivet ABS0112-24-02C Item 50
13 Receptacle NAS1791A3-3 Item 74
26 Rivet NSA5414N24-12A Item 86
h Drill the flange item 31 to match the holes with the structure.
j Install :
1 Flange F5331842100095 Item 31
54 Rivet NSA5415V40-18A Item 88
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
a Remove :
74 Rivet Item (63) Discard
1 Flange Item (29)
b On bench, transfer the existing holes of the receptacles from the old flange
item (29) to the new flange item 29 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331842000095 Item 29
d On bench, drill the new flange item 29 to match the holes with the
receptacles items 73 and 74.
f On bench, install :
17 Receptacle NAS1791A3-2 Item 73
34 Rivet ABS0112-24-02C Item 50
18 Receptacle NAS1791A3-3 Item 74
36 Rivet NSA5414N24-12A Item 86
h Drill the flange item 29 to match the holes with the structure.
j Install :
1 Flange F5331842000095 Item 29
74 Rivet NSA5415V40-18A Item 88
a Remove :
74 Rivet Item (63) Discard
1 Flange Item (30)
b On bench, transfer the existing holes of the receptacles from the old flange
item (30) to the new flange item 30 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331842000195 Item 30
d On bench, drill the new flange item 30 to match the holes with the
receptacles items 73 and 74.
f On bench, install :
17 Receptacle NAS1791A3-2 Item 73
34 Rivet ABS0112-24-02C Item 50
18 Receptacle NAS1791A3-3 Item 74
36 Rivet NSA5414N24-12A Item 86
h Drill the flange item 30 to match the holes with the structure.
j Install :
1 Flange F5331842000195 Item 30
74 Rivet NSA5415V40-18A Item 88
(g) Install the panels between FR47 and the Main Landing Gear.
Refer to Figure 1, Sheets 1 and 2
(2) Config. 02
(a) Remove the panels between FR47 and the Main Landing Gear for access.
Refer to Figure 1, Sheets 1 and 2
(b) Replace the flanges in the belly fairing between FR37.4 and FR39.1.
Refer to Kit 533166A01R01
Refer to Figure 2, Sheets 1 thru 7
a Remove :
102 Rivet Item (63) Discard
1 Flange Item (1)
b On bench, transfer the existing holes of the receptacles from the old flange
item (1) to the new flange item 1 to a diameter comprised between 6.5 mm
(0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331426000095 Item 1
d On bench, drill the new flange item 1 to match the holes with the receptacles
item 74.
f On bench, install :
36 Receptacle NAS1791A3-3 Item 74
72 Rivet NSA5414N24-12A Item 86
h Drill the flange item 1 to match the holes with the structure.
j Install :
1 Flange F5331426000095 Item 1
102 Rivet NSA5415V40-18A Item 88
a Remove :
19 Rivet Item (63) Discard
1 Flange Item (4)
b On bench, transfer the existing holes of the receptacles from the old flange
item (4) to the new flange item 4 to a diameter comprised between 6.5 mm
(0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331426300095 Item 4
d On bench, drill the new flange item 4 to match the holes with the receptacles
item 74.
f On bench, install :
5 Receptacle NAS1791A3-3 Item 74
10 Rivet NSA5414N24-12A Item 86
h Drill the flange item 4 to match the holes with the structure.
j Install :
1 Flange F5331426300095 Item 4
19 Rivet NSA5415V40-18A Item 88
a Remove :
49 Rivet Item (63) Discard
1 Flange Item (2)
6 Rivet Item (52) Discard
5 Rivet Item (58) Discard
5 Bush Item (57) Discard
2 Rivet Item (53) Discard
3 Bolt Item (83) Retain
3 Nut Item (84) Discard
1 Web Item (8)
4 Rivet Item (65) Discard
1 Support Item (105) Retain
b On bench, temporarily put in position the new flange item 6 on the new
web item 8.
1 Flange F5331426600095 Item 6
1 Web F5331426520095 Item 8
c On bench, drill the flange item 6 to match the holes of the web item 8.
f On bench, transfer the existing holes of the receptacles from the old flange
item (2) and the old web item (8) to the new flanges items 2 and 6 to a
diameter comprised between 6.5 mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331426100095 Item 2
h On bench, drill the new flanges items 2 and 6 to match the holes with
the receptacles item 74.
j On bench, install :
17 Receptacle NAS1791A3-3 Item 74
34 Rivet NSA5414N24-12A Item 86
k Temporarily, put in position the flange item 2 and the web item 8 to the
structure.
l Drill the flange item 2 and the web item 8 to match the holes with the
structure.
n Install :
1 Flange F5331426100095 Item 2
1 Web F5331426520095 Item 8
11 Rivet ASNA2050DXJ4020 Item 63
38 Rivet NSA5415V40-18A Item 88
6 Rivet ASNA0082-203 Item 52
5 Bolt EN6115V2-2 Item 69
5 Nut ASNA2531-2 Item 67
2 Rivet ASNA0082-204 Item 53
3 Bolt Item (83)
3 Nut NSA5050-3 Item 84
1 Support Item (105)
4 Rivet ASNA2051DCJ3215 Item 65
a Remove :
6 Rivet Item (64) Discard
3 Receptacle Item (73) Discard
9 Rivet Item (59) Discard
9 Bush Item (57) Discard
1 Gusset Item (100) Retain
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
b On bench, transfer the existing holes of the receptacles from the old flange
item (3) to the new flange item 3 to a diameter comprised between 6.5 mm
(0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331426200095 Item 3
d On bench, drill the new flange item 3 to match the holes with the receptacles
item 74.
f On bench, install :
24 Receptacle NAS1791A3-3 Item 74
48 Rivet NSA5414N24-12A Item 86
h Drill the flange item 3 to match the holes with the structure.
j Install :
1 Flange F5331426200095 Item 3
64 Rivet NSA5415V40-18A Item 88
3 Rivet NAS1919M05S05W Item 80
4 Rivet NAS1921M05S03W Item 82
1 Gusset Item (100)
2 Gusset Item (102)
9 Bolt EN6115V2-3 Item 70
9 Nut ASNA2531-2 Item 67
k Drill the flange item 3 to match the holes of the gussets items (100) and
(102).
l Install :
3 Receptacle NAS1791A3-2 Item 73
6 Rivet NSA5414N24-12A Item 86
a Remove :
8 Rivet Item (64) Discard
4 Receptacle Item (73) Discard
12 Rivet Item (59) Discard
12 Bush Item (57) Discard
1 Gusset Item (101) Retain
1 Gusset Item (102) Retain
2 Gusset Item (104) Retain
64 Rivet Item (63) Discard
3 Rivet Item (80) Discard
1 Flange Item (5)
NOTE : If necessary, remove items (57), (59) (101), (102) and (104).
b On bench, transfer the existing holes of the receptacles from the old flange
item (5) to the new flange item 5 to a diameter comprised between 6.5 mm
(0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331426400095 Item 5
d On bench, drill the new flange item 5 to match the holes with the receptacles
item 74.
f On bench, install :
28 Receptacle NAS1791A3-3 Item 74
56 Rivet NSA5414N24-12A Item 86
h Drill the flange item 5 to match the holes with the structure.
j Install :
1 Flange F5331426400095 Item 5
64 Rivet NSA5415V40-18A Item 88
3 Rivet NAS1919M05S05W Item 80
1 Gusset Item (101)
1 Gusset Item (102)
2 Gusset Item (104)
12 Bolt EN6115V2-3 Item 70
12 Nut ASNA2531-2 Item 67
k Drill the flange item 5 to match the holes of the gussets items (101), (102)
and (104).
l Install :
4 Receptacle NAS1791A3-2 Item 73
8 Rivet NSA5414N24-12A Item 86
(c) Replace the flanges in the belly fairing between FR39.1 and FR44.
Refer to Kit 533166A02R00
Refer to Figure 3, Sheets 1 thru 8
a Remove :
72 Rivet Item (63) Discard
1 Flange Item (9)
b On bench, transfer the existing holes of the receptacles from the old flange
item (9) to the new flange item 9 to a diameter comprised between 6.5 mm
(0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331531200095 Item 9
d On bench, drill the new flange item 9 to match the holes with the receptacles
items 68 and 74.
f On bench, install :
30 Receptacle EN6092-01 Item 68
60 Rivet NSA5414N24-12A Item 86
20 Receptacle NAS1791A3-3 Item 74
40 Rivet ABS0112-24-02C Item 50
h Drill the flange item 9 to match the holes with the structure.
j Install :
1 Flange F5331531200095 Item 9
72 Rivet NSA5415V40-18A Item 88
a Remove :
4 Rivet Item (123) Discard
1 Web Item (22) Discard
c Drill the web item 22 to match the holes with the structure.
e Install :
1 Web F5331556100695 Item 22
4 Rivet NSA5415V40-18A Item 88
a Remove :
48 Rivet Item (63) Discard
1 Flange Item (10)
b On bench, transfer the existing holes of the receptacles from the old flange
item (10) to the new flange item 10 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331532900095 Item 10
d On bench, drill the new flange item 10 to match the holes with the
receptacles item 68.
f On bench, install :
32 Receptacle EN6092-01 Item 68
64 Rivet NSA5414N24-12A Item 86
h Drill the flange item 10 to match the holes with the structure.
j Install :
1 Flange F5331532900095 Item 10
48 Rivet NSA5415V40-18A Item 88
a Remove :
47 Rivet Item (63) Discard
2 Rivet Item (79) Discard
1 Support Item (124) Retain
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
b On bench, transfer the existing holes of the receptacles from the old flange
item (11) to the new flange item 11 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331533200095 Item 11
d On bench, drill the new flange item 11 to match the holes with the
receptacles item 68.
f On bench, install :
32 Receptacle EN6092-01 Item 68
64 Rivet NSA5414N24-12A Item 86
h Drill the flange item 11 to match the holes with the structure.
j Install :
1 Flange F5331533200095 Item 11
1 Support Item (124)
46 Rivet NSA5415V40-18A Item 88
1 Rivet ASNA2050DXJ4020 Item 63
2 Rivet NAS1919M05S04W Item 79
a Remove :
103 Rivet Item (63) Discard
1 Support Item (125) Retain
1 Flange Item (18)
1 Flange Item (19)
b On bench, transfer the existing holes of the receptacles from the old flanges
items (18) and (19) to the new flanges items 18 and 19 to a diameter
comprised between 6.5 mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331547300095 Item 18
1 Flange F5331547400095 Item 19
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
d On bench, drill the new flanges items 18 and 19 to match the holes with
the receptacles items 68 and 74.
f On bench, install :
31 Receptacle EN6092-01 Item 68
94 Rivet NSA5414N24-12A Item 86
16 Receptacle NAS1791A3-3 Item 74
h Drill the flanges items 18 and 19 to match the holes with the structure.
j Install :
1 Flange F5331547300095 Item 18
1 Flange F5331547400095 Item 19
1 Support Item (125)
99 Rivet NSA5415V40-18A Item 88
4 Rivet ASNA2050DXJ4020 Item 63
6 Replace the flange on the central web between FR39.1 and FR44.
Refer to Figure 3, Sheets 1 and 7
a Remove :
136 Rivet Item (63) Discard
1 Flange Item (13)
1 Flange Item (14)
b On bench, transfer the existing holes of the receptacles from the old flanges
items (13) and (14) to the new flanges items 13 and 14 to a diameter
comprised between 6.5 mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331537300095 Item 13
1 Flange F5331537400095 Item 14
d On bench, drill the new flanges items 13 and 14 to match the holes with
the receptacles items 68 and 74.
f On bench, install :
54 Receptacle EN6092-01 Item 68
134 Rivet NSA5414N24-12A Item 86
13 Receptacle NAS1791A3-3 Item 74
h Drill the flanges items 13 and 14 to match the holes with the structure.
j Install :
1 Flange F5331537300095 Item 13
1 Flange F5331537400095 Item 14
136 Rivet NSA5415V40-18A Item 88
a Remove :
111 Rivet Item (63) Discard
1 Flange Item (16)
1 Flange Item (17)
b On bench, transfer the existing holes of the receptacles from the old flanges
items (16) and (17) to the new flanges items 16 and 17 to a diameter
comprised between 6.5 mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331542300095 Item 16
1 Flange F5331542400095 Item 17
d On bench, drill the new flanges items 16 and 17 to match the holes with
the receptacles items 68 and 74.
f On bench, install :
37 Receptacle EN6092-01 Item 68
104 Rivet NSA5414N24-12A Item 86
15 Receptacle NAS1791A3-3 Item 74
h Drill the flanges items 16 and 17 to match the holes with the structure.
j Install :
1 Flange F5331542300095 Item 16
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
(d) Replace the flanges in the belly fairing between FR44 and FR47.
Refer to Kit 533166A03R00 and Kit 533166A06R01
Refer to Figure 5, Sheets 1 thru 5
a Remove :
22 Rivet Item (88) Discard
25 Rivet Item (76) Discard
3 Rivet Item (78) Discard
1 Rivet Item (55) Discard
8 Rivet Item (81) Discard
8 Washer Item (56) Discard
6 Rivet Item (66) Discard
20 Rivet Item (51) Discard
3 Receptacle Item (72) Discard
7 Receptacle Item (89) Discard
1 Shim Item (23)
1 Shim Item (24)
1 Flange Item (12)
b On bench, transfer the existing holes of the receptacles from the old shim
item (23) to the new shim item 23 to a diameter comprised between 6.5 mm
(0.256 in.) and 6.6 mm (0.260 in.).
1 Shim F5331562120095 Item 23
c On bench, transfer the existing holes of the receptacles from the old shim
item (24) to the new shim item 24 to a diameter comprised between 6.5 mm
(0.256 in.) and 6.6 mm (0.260 in.).
1 Shim F5331562220095 Item 24
d On bench, transfer the existing holes of the receptacles from the old flange
item (12) to the new flange item 12 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331534400095 Item 12
f On bench, drill the new flange item 12 to match the holes with the
receptacles item 68.
h On bench, install :
i Temporarily, put in position the flange item 12, the shims items 23 and
24 to the structure.
j Drill the flange item 12, the shims items 23 and 24 to match the holes
with the structure.
l Install :
1 Flange F5331534400095 Item 12
22 Rivet NSA5415V40-18A Item 88
25 Rivet NAS1919M05S03 Item 76
6 Rivet ASNA2051DXJ4020 Item 66
3 Rivet NAS1919M05S04 Item 78
1 Shim F5331562120095 Item 23
1 Shim F5331562220095 Item 24
1 Rivet ASNA0082B203 Item 55
20 Rivet ABS0112-24-04C Item 51
8 Rivet NAS1921M05S03 Item 81
8 Washer ASNA0113-40CA Item 56
3 Nut NAS1791A3-1 Item 72
7 Nut NAS1792A3-1 Item 89
a Remove :
50 Rivet Item (88) Discard
5 Rivet Item (53) Discard
4 Rivet Item (54) Discard
12 Rivet Item (66) Discard
4 Rivet Item (82) Discard
1 Splice Item (140)
1 Splice Item (7)
1 Flange Item (139)
b On bench, transfer the existing holes of the receptacles from the old flange
item (139) to the new flange item 139 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331540000495 Item 139
NOTE(01) This flange is supplied in the Kit 533166A06R01. Do not use the
flange item 15 supplied in the Kit 533166A03R00.
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
d On bench, drill the new flange item 139 to match the holes with the
receptacles items 68 and 73.
f On bench, install :
g Temporarily, put in position to the structure the flange item 139 and the
splices item 7 and item 140.
1 Splice F5331518700695 Item 7
1 Splice F5331567620000 Item 140
h Drill the flange item 139, the splices item 7 and item 140 to match the
holes with the structure.
j Install :
1 Flange F5331540000495 Item 139
50 Rivet NSA5415V40-18A Item 88
4 Rivet NAS1921M05S03W Item 82
1 Splice F5331518700695 Item 7
1 Splice F5331567620000 Item 140
12 Rivet ASNA2051DXJ4020 Item 66
5 Rivet ASNA0082-204 Item 53
4 Rivet ASNA0082-205 Item 54
a Remove :
33 Rivet Item (63) Discard
1 Flange Item (20)
b On bench, transfer the existing holes of the receptacles from the old flange
item (20) to the new flange item 20 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
d On bench, drill the new flange item 20 to match the holes with the
receptacles item 68 and 74.
f On bench, install :
h Drill the flange item 20 to match the holes with the structure.
j Install :
1 Flange F5331552500095 Item 20
33 Rivet NSA5415V40-18A Item 88
a Remove :
22 Rivet Item (66) Discard
15 Rivet Item (63) Discard
1 Flange Item (21)
b On bench, transfer the existing holes of the receptacles from the old flange
item (21) to the new flange item 21 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331553200095 Item 21
d On bench, drill the new flange item 21 to match the holes with the
receptacles item 68 and 74.
f On bench, install :
h Drill the flange item 21 to match the holes with the structure.
j Install :
1 Flange F5331553200095 Item 21
22 Rivet NSA5414V40-18A Item 90
15 Rivet NSA5415V40-18A Item 88
a Remove :
1 Rivet Item (63) Discard
39 Rivet Item (79) Discard
or
b On bench, transfer the existing holes of the receptacles from the old flange
item (27) to the new flange item 27 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331733100095 Item 27
d On bench, drill the new flange item 27 to match the holes with the
receptacles item 73.
f On bench, install :
48 Receptacle NAS1791A3-2 Item 73
96 Rivet NSA5414N24-12A Item 86
h Drill the flange item 27 to match the holes with the structure.
j Install :
1 Flange F5331733100095 Item 27
1 Gusset Item (109)
1 Plate Item (111)
1 Gusset Item (107)
1 Plate Item (113)
1 Rivet NSA5415V40-18A Item 88
39 Rivet NAS1919M05S04W Item 79
or
NOTE(01) If existing, items (107), (109), (111) and (113) were retained
at removal.
NOTE(02) If existing on aircraft, attach the parts items (107), (109), (111)
and (113) with rivets item 79.
a Remove :
6 Rivet Item (63) Discard
34 Rivet Item (79) Discard
or
b On bench, transfer the existing holes of the receptacles from the old flange
item (28) to the new flange item 28 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331733100195 Item 28
d On bench, drill the new flange item 28 to match the holes with the
receptacles item 73.
f On bench, install :
48 Receptacle NAS1791A3-2 Item 73
96 Rivet NSA5414N24-12A Item 86
h Drill the flange item 28 to match the holes with the structure.
j Install :
1 Flange F5331733100195 Item 28
1 Plate Item (116)
1 Plate Item (117)
1 Gusset Item (108)
1 Plate Item (112)
1 Gusset Item (110)
6 Rivet NSA5415V40-18A Item 88
34 Rivet NAS1919M05S04W Item 79
or
NOTE(01) If existing, items (108), (110), (112), (116) and (117) were
retained at removal.
NOTE(02) If existing on aircraft, attach the parts items (108), (110), (112),
(116) and (117) with rivets item 79.
a Remove :
23 Rivet Item (63) Discard
31 Rivet Item (79) Discard
or
b On bench, transfer the existing holes of the receptacles from the old flange
item (26) to the new flange item 26 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331733000095 Item 26
d On bench, drill the new flange item 26 to match the holes with the
receptacles item 73.
f On bench, install :
63 Receptacle NAS1791A3-2 Item 73
126 Rivet NSA5414N24-12A Item 86
h Drill the flange item 26 to match the holes with the structure.
j Install :
1 Flange F5331733000095 Item 26
1 Plate Item (114)
1 Plate Item (115)
23 Rivet NSA5415V40-18A Item 88
31 Rivet NAS1919M05S04W Item 79
or
NOTE(02) If existing on aircraft, attach the parts items (114) and (115)
with rivets item 79.
(f) Replace the flanges in the belly fairing between FR53.2 and FR53.8.
Kit 533166A05R00
Refer to Figure 7, Sheets 1 and 8
a Remove :
4 Rivet Item (64) Discard
2 Receptacle Item (73) Discard
8 Rivet Item (59) Discard
12 Bush Item (57) Discard
1 Gusset Item (118) Retain
1 Gusset Item (106) Retain
42 Rivet Item (63) Discard
4 Rivet Item (60) Discard
1 Flange Item (33)
b On bench, transfer the existing holes of the receptacles from the old flange
item (33) to the new flange item 33 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331842300095 Item 33
d On bench, drill the new flange item 33 to match the holes with the
receptacles item 74.
f On bench, install :
31 Receptacle NAS1791A3-3 Item 74
62 Rivet NSA5414N24-12A Item 86
h Drill the flange item 33 to match the holes with the structure.
j Install :
1 Flange F5331842300095 Item 33
42 Rivet NSA5415V40-18A Item 88
1 Gusset Item (118)
1 Gusset Item (106)
8 Bolt EN6115V2-3 Item 70
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
k Drill the flange item 33 to match the holes with the gussets items (106)
and (118).
l Install :
2 Receptacle NAS1791A3-2 Item 73
4 Rivet NSA5414N24-12A Item 86
a Remove :
18 Rivet Item (64) Discard
9 Receptacle Item (74) Discard
2 Rivet Item (59) Discard
6 Bush Item (57) Discard
4 Rivet Item (60) Discard
17 Rivet Item (63) Discard
1 Flange Item (32)
NOTE : To permit the removal of the receptacles item (74), remove and
retain the fasteners and the support existing on the aircraft.
b On bench, transfer the existing holes of the receptacles from the old flange
item (32) to the new flange item 32 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331842200095 Item 32
d On bench, drill the new flange item 32 to match the holes with the
receptacles item 74.
f On bench, install :
22 Receptacle NAS1791A3-3 Item 74
44 Rivet NSA5414N24-12A Item 86
h Drill the flange item 32 to match the holes with the structure.
j Install :
1 Flange F5331842200095 Item 32
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
k Drill the flange item 32 to match the holes with the existing gussets.
l Install :
2 Receptacle NAS1791A3-3 Item 74
4 Rivet NSA5414N24-12A Item 86
a Remove :
4 Rivet Item (64) Discard
2 Receptacle Item (73) Discard
6 Rivet Item (59) Discard
6 Bush Item (57) Discard
2 Gusset Item (119) Retain
78 Rivet Item (63) Discard
1 Flange Item (34)
b On bench, transfer the existing holes of the receptacles from the old flange
item (34) to the new flange item 34 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331842400095 Item 34
d On bench, drill the new flange item 34 to match the holes with the
receptacles item 74.
f On bench, install :
28 Receptacle NAS1791A3-3 Item 74
56 Rivet NSA5414N24-12A Item 86
h Drill the flange item 34 to match the holes with the structure.
j Install :
1 Flange F5331842400095 Item 34
78 Rivet NSA5415V40-18A Item 88
6 Bolt EN6115V2-3 Item 70
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
k Drill the flange item 34 to match the holes with the gussets item (119).
l Install :
2 Receptacle NAS1791A3-2 Item 73
4 Rivet NSA5414N24-12A Item 86
a Remove :
4 Rivet Item (64) Discard
2 Receptacle Item (73) Discard
b On bench, transfer the existing holes of the receptacles from the old flange
item (35) to the new flange item 35 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331842400195 Item 35
d On bench, drill the new flange item 35 to match the holes with the
receptacles item 74.
f On bench, install :
28 Receptacle NAS1791A3-3 Item 74
56 Rivet NSA5414N24-12A Item 86
h Drill the flange item 35 to match the holes with the structure.
j Install :
1 Flange F5331842400195 Item 35
78 Rivet NSA5415V40-18A Item 88
6 Bolt EN6115V2-3 Item 70
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
k Drill the flange item 34 to match the holes with the gussets item (120).
l Install :
2 Receptacle NAS1791A3-2 Item 73
4 Rivet NSA5414N24-12A Item 86
a Remove :
6 Rivet Item (61) Discard
or
or
and
b On bench, transfer the existing holes of the receptacles from the old flanges
items (36) and (37) to the new flanges items 36 and 37 to a diameter
comprised between 6.5 mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331842500095 Item 36
1 Flange F5331842600095 Item 37
d On bench, drill the new flanges items 36 and 37 to match the holes with
the receptacles item 74.
f On bench, install :
13 Receptacle NAS1791A3-3 Item 74
26 Rivet NSA5414N24-12A Item 86
h Drill the flanges items 36 and 37 to match the holes with the structure.
j Install :
1 Flange F5331842500095 Item 36
1 Flange F5331842600095 Item 37
50 Rivet NSA5415V40-18A Item 88
or
and
or
a Remove :
54 Rivet Item (63) Discard
1 Flange Item (31)
b On bench, transfer the existing holes of the receptacles from the old flange
item (31) to the new flange item 31 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331842100095 Item 31
d On bench, drill the new flange item 31 to match the holes with the
receptacles items 73 and 74.
f On bench, install :
13 Receptacle NAS1791A3-2 Item 73
26 Rivet ABS0112-24-02C Item 50
13 Receptacle NAS1791A3-3 Item 74
26 Rivet NSA5414N24-12A Item 86
h Drill the flange item 31 to match the holes with the structure.
j Install :
1 Flange F5331842100095 Item 31
54 Rivet NSA5415V40-18A Item 88
a Remove :
74 Rivet Item (63) Discard
1 Flange Item (29)
b On bench, transfer the existing holes of the receptacles from the old flange
item (29) to the new flange item 29 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331842000095 Item 29
d On bench, drill the new flange item 29 to match the holes with the
receptacles items 73 and 74.
f On bench, install :
17 Receptacle NAS1791A3-2 Item 73
34 Rivet ABS0112-24-02C Item 50
18 Receptacle NAS1791A3-3 Item 74
36 Rivet NSA5414N24-12A Item 86
h Drill the flange item 29 to match the holes with the structure.
j Install :
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
a Remove :
74 Rivet Item (63) Discard
1 Flange Item (30)
b On bench, transfer the existing holes of the receptacles from the old flange
item (30) to the new flange item 30 to a diameter comprised between 6.5
mm (0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331842000195 Item 30
d On bench, drill the new flange item 30 to match the holes with the
receptacles items 73 and 74.
f On bench, install :
17 Receptacle NAS1791A3-2 Item 73
34 Rivet ABS0112-24-02C Item 50
18 Receptacle NAS1791A3-3 Item 74
36 Rivet NSA5414N24-12A Item 86
h Drill the flange item 30 to match the holes with the structure.
j Install :
1 Flange F5331842000195 Item 30
74 Rivet NSA5415V40-18A Item 88
(g) Install the panels between FR47 and the Main Landing Gear.
Refer to Figure 1, Sheets 1 and 2
(a) Preparation
1 Make sure that the aircraft is electrically grounded (Refer to AMM 12-34-24,
Page block 201).
3 Remove the belly-fairing access panels (Refer to AMM 53-35-13, Page block
401 and AMM 06-41-53, Page block 001) :
(b) Remove the panels between FR47 and the Main Landing Gear for access.
Refer to Figure 1, Sheets 1 and 2
1 Remove :
50 Rivet Item (88) Discard
4 Rivet Item (54) Discard
12 Rivet Item (66) Discard
4 Rivet Item (82) Discard
5 Rivet Item (53) Discard
1 Splice Item (7)
1 Splice Item (140)
1 Flange Item (139)
2 On bench, transfer the existing holes of the receptacles from the old flange item
(139) to the new flange item 139 to a diameter comprised between 6.5 mm
(0.256 in.) and 6.6 mm (0.260 in.).
1 Flange F5331540000495 Item 139
4 On bench, drill the new flange item 139 to match the holes with the receptacles
items 68 and 73.
6 On bench, install :
28 Receptacle EN6092-01 Item 68
32 Receptacle NAS1791A3-2 Item 73
120 Rivet NSA5414N24-12A Item 86
7 Temporarily, put in position to the structure the flange item 139, the splices
item 7 and item 140.
1 Splice F5331518700695 Item 7
1 Splice F5331567620000 Item 140
8 Drill the flange item 139 and the splices item 7 and item 140 to match the
holes with the structure.
10 Install :
1 Flange F5331540000495 Item 139
50 Rivet NSA5415V40-18A Item 88
4 Rivet NAS1921M05S03W Item 82
1 Splice F5331518700695 Item 7
1 Splice F5331567620000 Item 140
12 Rivet ASNA2051DXJ4020 Item 66
5 Rivet ASNA0082-204 Item 53
4 Rivet ASNA0082-205 Item 54
(d) Install the panels between FR47 and the Main Landing Gear.
Refer to Figure 1, Sheets 1 and 2
(e) Test
No test.
(f) Close up
1 Make sure that the work areas are clean and clear of tools and other items
of equipment.
2 Install the belly-fairing access panels (Refer to AMM 53-35-13, Page block 401
and AMM 06-41-53, Page block 001) :
C. TEST
(a) Do the test procedure after removal/installation of the air outlet flap assembly (Refer
to AMM 53-35-42, Page block 401).
D. CLOSE UP
(1) Config. 01
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install the LH and RH belly fairing access panels behind MLG doors (Refer to AMM
53-35-13, Page block 401).
(c) Install the belly-fairing access panels (Refer to AMM 53-35-13, Page block 401
and AMM 06-41-53, Page block 001) :
- For Kit 533166A01R01: access panels 191AB, 191BB, 191DB and 192BB.
- For Kit 533166A02R00: access panels 191DB, 191FB, 192BB, 192GB, 192JB,
192MB, 192NB, 192PB, 193AB, 193BB and 193DB.
- For Kit 533166A03R00: access panels 149AB, 195BB, 195CB, 195DB, 196AB
(193DB, 193MB, 193NB if necessary).
- For Kit 533166A04R00 and Kit 533166A05R00: access panels 197AB, 197BB,
197EB, 197FB, 197GB, 197HB, 198BB, 198EB, 198GB, 198HB.
(d) Install the air outlet flap assembly (Refer to AMM 53-35-42, Page block 401).
(e) Install the access door of the CLG door ground opening handle (149BB) (Refer
to AMM 52-42-32, Page block 401).
(f) Install the access door of the MLG door ground opening handle (149CB) (Refer
to AMM 52-42-32, Page block 401).
(g) Close the MLG doors (Refer to AMM 32-12-00, Page block 201).
(h) Close the FWD cargo-compartment door 821 (Refer to AMM 52-30-00, Page
block 201).
(j) Restore the systems and the aircraft to normal operating condition.
(2) Config. 02
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install the LH and RH belly fairing access panels behind MLG doors (Refer to AMM
53-35-13, Page block 401).
(c) Install the belly-fairing access panels (Refer to AMM 53-35-13, Page block 401
and AMM 06-41-53, Page block 001) :
- For Kit 533166A01R01: access panels 191AB, 191BB, 191DB and 192BB.
- For Kit 533166A02R00: access panels 191DB, 191FB, 192BB, 192GB, 192JB,
192MB, 192NB, 192PB, 193AB, 193BB and 193DB.
- For Kit 533166A04R00 and Kit 533166A05R00: access panels 197AB, 197BB,
197EB, 197FB, 197GB, 197HB, 198BB, 198EB, 198GB, 198HB.
(d) Install the air outlet flap assembly (Refer to AMM 53-35-42, Page block 401).
(e) Install the access door of the CLG door ground opening handle (149BB) (Refer
to AMM 52-42-32, Page block 401).
(f) Install the access door of the MLG door ground opening handle (149CB) (Refer
to AMM 52-42-32, Page block 401).
(g) Close the MLG doors (Refer to AMM 32-12-00, Page block 201).
(h) Close the FWD cargo-compartment door 821 (Refer to AMM 52-30-00, Page
block 201).
(j) Restore the systems and the aircraft to normal operating condition.
E. DOCUMENTATION
Write in the applicable aircraft records that you have done all the work given in the Service Bulletin.
Figure 1, Sheet 1
Config. 01 thru 02: Removal / Installation of the panels between FR47 and the Main Landing Gear
Figure 1, Sheet 2
Config. 01 thru 02: Removal / Installation of the panels between FR47 and the Main Landing Gear
Figure 2, Sheet 1
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR37.4 and FR39.1
Figure 2, Sheet 2
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR37.4 and FR39.1
Figure 2, Sheet 3
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR37.4 and FR39.1
Figure 2, Sheet 4
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR37.4 and FR39.1
Figure 2, Sheet 5
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR37.4 and FR39.1
Figure 2, Sheet 6
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR37.4 and FR39.1
Figure 2, Sheet 7
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR37.4 and FR39.1
Figure 3, Sheet 1
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR39.1 and FR44
Figure 3, Sheet 2
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR39.1 and FR44
Figure 3, Sheet 3
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR39.1 and FR44
Figure 3, Sheet 4
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR39.1 and FR44
Figure 3, Sheet 5
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR39.1 and FR44
Figure 3, Sheet 6
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR39.1 and FR44
Figure 3, Sheet 7
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR39.1 and FR44
Figure 3, Sheet 8
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR39.1 and FR44
Figure 4, Sheet 1
Config. 01: Replacement of the Flanges in the Belly Fairing between FR44 and FR47
Figure 4, Sheet 2
Config. 01:
DATE : Jan 29/07 Replacement of the Flanges in the BellyBULLETIN
SERVICE Fairing between FR44 and FR47
No. : A330-53-3166
Figure 4, Sheet 3
Config. 01:
DATE : Jan 29/07 Replacement of the Flanges in the BellyBULLETIN
SERVICE Fairing between FR44 and FR47
No. : A330-53-3166
Figure 4, Sheet 4
Config. 01:
DATE : Jan 29/07 Replacement of the Flanges in the BellyBULLETIN
SERVICE Fairing between FR44 and FR47
No. : A330-53-3166
Figure 4, Sheet 5
Config. 01:
DATE : Jan 29/07 Replacement of the Flanges in the BellyBULLETIN
SERVICE Fairing between FR44 and FR47
No. : A330-53-3166
Figure 5, Sheet 1
Config. 02: Replacement of the Flanges in the Belly Fairing between FR44 and FR47
Figure 5, Sheet 2
Config. 02: Replacement of the Flanges in the Belly Fairing between FR44 and FR47
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
Figure 5, Sheet 3
Config. 02: Replacement of the Flanges in the Belly Fairing between FR44 and FR47
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
Figure 5, Sheet 4
Config. 02: Replacement of the Flanges in the Belly Fairing between FR44 and FR47
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
Figure 5, Sheet 5
Config. 02: Replacement of the Flanges in the Belly Fairing between FR44 and FR47
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
Figure 6, Sheet 1
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing on the FR53.2
Figure 6, Sheet 2
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing on the FR53.2
Figure 6, Sheet 3
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing on the FR53.2
Figure 6, Sheet 4
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing on the FR53.2
Figure 7, Sheet 1
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR53.2 and FR53.8
Figure 7, Sheet 2
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR53.2 and FR53.8
Figure 7, Sheet 3
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR53.2 and FR53.8
Figure 7, Sheet 4
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR53.2 and FR53.8
Figure 7, Sheet 5
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR53.2 and FR53.8
Figure 7, Sheet 6
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR53.2 and FR53.8
Figure 7, Sheet 7
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR53.2 and FR53.8
Figure 7, Sheet 8
Config. 01 thru 02: Replacement of the Flanges in the Belly Fairing between FR53.2 and FR53.8
Figure 8, Sheet 1
Config. 02: Replacement of the Flange of FR47 in the Belly Fairing ADDITIONAL WORK
Figure 8, Sheet 2
Config. 02: Replacement of the Flange of FR47 in the Belly Fairing ADDITIONAL WORK
DATE : Jan 29/07 SERVICE BULLETIN No. : A330-53-3166
Operator comments:............................................................................................................................................
.............................................................................................................................................................................
.............................................................................................................................................................................
If operational documentation is affected (see Paragraph 1.K of this SB): If information is needed prior to next
normal revision or prior to SB embodiment, please indicate required service(s):
Either : Advance data................................................................................... YES/NO
Or : Intermediate/Temporary revision ..................................................... YES/NO
Important Information: This SB will only be incorporated in your maintenance and operational documentation
if this sheet is returned to Airbus and signed by a duly authorised representative. With the next feasible
revision, this will result in
- updating of maintenance documentation to show pre and post SB data.
- updating of maintenance and operational documentation to show post SB data
after embodiment.
If this SB requires previous or simultaneous accomplishment of other SBs, Airbus shall automatically include
them in the manual revisions. Refer to SIL 00-037 for detailed information.
Please return this completed sheet to:
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE
Use this form to tell us what is your perception of the quality of this Service Bulletin.The reported data that you
provide us will be used to analyse areas of difficulties and to take corrective action to futher improve the quality
of our Service Bulletins.
We thank you for the time you have taken in completing this form.
If you have had difficulties in the accomplishment of this SB please quote below the area(s) and give a short
description of the issue.
Comments :
Operator : Date:
Name/Title :
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE