Professional Documents
Culture Documents
Mitsubishi Electric MSZ-FH VE Remote Controller Eng PDF
Mitsubishi Electric MSZ-FH VE Remote Controller Eng PDF
8 5 校
Simple Remote Controller User Guide C FAN SPEED AND AIRFLOW DIRECTION ADJUSTMENT
【MSZ-FH series】
FAN L-VANE-R
Press to select fan speed. Press to select airflow direction.
Each press changes fan speed Each press changes airflow direction in the following order:
in the following order: (AUTO) (Silent) (Low) (Med.) (High) (Super High)
The remote controller has a simple,
stylish design with emphasis on (AUTO) (1) (2) (3) (4) (5) (SWING)
▲
(SWING)
the double vane
As time passes, airfl ow will become more The purifier neutralizes bacteria as it
Plasma
like natural wind. The continuously gentle passes through the plasma device. space
Air
Press this button to toggle the function on/off. Press this button to toggle the function on/off.
2 Press to select operation mode. Each press
F
changes mode in the following order:
TIMER OPERATION
(AUTO) (COOL) (DRY) (HEAT) (FAN) A C ON/OFF TIMER WEEKLY TIMER
1 Press or during operation to set the timer. 1 Press to enter the weekly timer setting mode.
3 Press or to set the temperature.
Each press raises or lowers the temperature by 1°C. (ON timer) : The unit turns ON at the set time. 2 Press and to select setting day and number.
(OFF timer) : The unit turns OFF at the set time.
3 Press , , and to set ON/OFF, time, and temperature.
B
* or blinks.
CONVENIENT ONE-TOUCH FUNCTIONS * Make sure that the current time and day are set correctly.
4 Press to complete and transmit the weekly timer setting.
Press these buttons to toggle these functions on/off. E
5 Press to turn the weekly timer ON. ( lights.)
ECONO COOL 2 Press (Increase) and (Decrease) to set the * When the weekly timer is ON, the day of the week whose timer setting is complete, will light.
B time of timer. Press again to turn the weekly timer OFF. ( goes out.)
A swing pattern is used for airflow to create an enhanced Each press increases or decreases the set time by 10 minutes. Timer ON. Change temp.
cooling sensation. This allows the temperature to be set 2°C • Set the timer while or is blinking. Temp. setting: 27°C Temp. setting: 28°C
Timer OFF.
higher without any loss of comfort.
0:30 7:30 8:30
G i-see OPERATION
i-save
Setting preferences can be saved and then activated in
i-see control mode SENSOR ABSENCE DETECTION INDIRECT/DIRECT
future uses simply by pressing the pressing the i-save button.
1 Press during COOL, DRY, The sensor detects
the floor temperature….
When no-one is in the room,
the unit automatically switches to
Press to activate INDIRECT/DIRECT
In normal heating mode, the lowest possible temperature setting is HEAT and AUTO mode to energy-saving mode. mode. This mode is only available when the
16°C, but using i-save, this value can be set as low as 10°C. activate i-see control mode. i-see control mode is effective.
10 minutes after
To avoid overcooling
• Press gently using a thin instrument. person leaves room
F
(INDIRECT) (DIRECT) (OFF)
Note: In the case of systems with multiple units (multi-systems), it is not • The default setting is “active”.
possible to set different operation modes for each unit. In addition, The unit monitors people……
in some cases, it may not be possible to use certain functions.
Allowing
G
ABSENCE DETECTION.
PREPARATION BEFORE OPERATION (SETTING CURRENT TIME) To warm from the
foot-level up 60 minutes after
person leaves room
• lights. (Operation display section)
1 Press CLOCK 2 Press the TIME 3 Press the DAY 4 Press CLOCK
button. button to set the button to set the again.
time. day. 3 Press again to release Enhance comfort by averting airflow away from
people, or set direct airflow to target people for quick
i-see control mode. cooling/heating.