Professional Documents
Culture Documents
MPC 4502 - 5502 New Fuser Detect Fuse PDF
MPC 4502 - 5502 New Fuser Detect Fuse PDF
MPC 4502 - 5502 New Fuser Detect Fuse PDF
Introduction to Global
Knowledgebase
Product pages
US Ricoh Color Multifunction Aficio MP C4502/A/G, C5502/A/G
Other users found this answer helpful Yes 0 No 0 Not what I was
searching for
Number of views: 66
0
• Some parts were added to the fusing belt unit, and part numbers were changed as shown below.
• In accordance with this change, do the steps described below whenever you replace the fusing belt unit.
• Do not touch the fusing belt. When you touch the fusing belt even though it is very soft, the touch may damage the fusing belt,
and SC544/SC554 may occur some hundreds pages or several tens kilo pages later than the replacement.
Changes:
• A unit detection fuse is now bundled together with the unit (see photo below).
• Two oil absorption pads were added to the fusing unit (see photo below).
Reason:
• With the new fuse, SC544/SC554/SC564/SC574 can all be reset without replacing the entire fusing unit.
• The pads will prevent oil from leaking from the fusing belt.
Note: This oil is used to moisten the fiber sheet that coats the nip pad in the fusing belt unit.
https://tscweb.custhelp.com/app/answers/detail/a_id/171806/kw/fuser/p_li/cF91c2VyaWQ... 8/23/2015
RTB No.: RD144072 : Parts component change of Fusing sleeve belt unit Page 2 of 4
1) Do the following when you remove the protective paper from the fusing belt.
Note: This is necessary because it is possible to press the belt by mistake or press the belt's surface, forming a dent on the belt. This
is a major cause of SC544/SC554.
1. Hold the lateral metal stays, and pinch the tape on the paper gently as shown.
IMPORTANT: Be careful not to press the fusing belt surface.
2. Peel of the tape very carefully, pulling the tape up in a vertical direction (90 degrees to the belt surface).
To Top
2) Do the following if you are replacing the fusing belt unit in order to clear SC544/SC554/SC564/SC574.
IMPORTA
NT:
Only attach the new detection fuse if you are replacing the fusing belt unit to clear one of the SCs listed above. If you
install this new fuse but none of these SCs has occurred, the PM counters for the fusing unit, pressure roller, and
others will not be reset properly.
https://tscweb.custhelp.com/app/answers/detail/a_id/171806/kw/fuser/p_li/cF91c2VyaWQ... 8/23/2015
RTB No.: RD144072 : Parts component change of Fusing sleeve belt unit Page 3 of 4
2. Remove the connector from the hook and attach the new detection fuse as shown.
3. Set the fuse into the hook, so that it rests within the edge of the metal frame.
3) Do the following to attach (or replace) the two oil absorption felt strips included with the unit.
2. Wipe the attachment surface for the felt with an alcohol-wetted cloth.
Note: If you do not wipe this area properly, the new felt will not adhere to the cover.
https://tscweb.custhelp.com/app/answers/detail/a_id/171806/kw/fuser/p_li/cF91c2VyaWQ... 8/23/2015
RTB No.: RD144072 : Parts component change of Fusing sleeve belt unit Page 4 of 4
3. Attach the oil absorption felt strips to the fusing lower cover, as shown.
Important: Attach the felt strips in alignment with lines A-D shown below
To Top
Products Categories
US Documentation
Ricoh Parts Catalog/PCIL
Color Multifunction RTB
Aficio MP C4502/A/G, C5502/A/G Technical Information
Savin Troubleshooting
Color Multifunction Mechanical
MP C4502/A/G, C5502/A/G Oil Leak/Spill
Lanier Service Codes
Color Multifunction SC500-SC599
MP C4502/A/G, C5502/A/G
https://tscweb.custhelp.com/app/answers/detail/a_id/171806/kw/fuser/p_li/cF91c2VyaWQ... 8/23/2015