Professional Documents
Culture Documents
TJ-8000 - Trus Joist Rim Board
TJ-8000 - Trus Joist Rim Board
• Multiple thicknesses,
grades, and products to
cover all your rim board
needs
• 1¼" Thickness matches
lateral load capacity of
2x nominal sawn lumber
in diaphragms
• Limited product warranty
Benefits of Trus Joist® Rim Board
• Longer lengths for faster installation and fewer joints
• Depths are sized to match TJI® joists—less cutting and material waste when
used together
• High vertical load transfer capacity
• Recognized and accepted by major building codes
For years, little attention was paid to the importance of lateral forces. However, recent
earthquake and hurricane disasters have demonstrated the importance of proper
lateral load transfer. Engineering analysis confirms that rim board is essential in a
home’s ability to resist the lateral loads generated by high winds and earthquakes.
Trus Joist® rim board products offer vertical load support and provide the nailing
surface necessary to adequately transfer wind and seismic loads. Manufactured
by Weyerhaeuser according to strict quality assurance requirements, they provide
strength, stiffness, and durability. We’re so confident about the performance of all
our rim board that it comes with a limited lifetime product warranty. When used with
TJI® joists, it offers the ultimate high performance floor.
Material Weights 2
Lateral Load Capacity 3 Approximate Material Weights (plf)
Rim Board Installation Detail 3
Depth
Design Properties 4 Trus Joist ® Product
9½" 117⁄ 8" 14" 16" 18" 20" 22" 24"
Nailing on Narrow Face 4
11 ⁄ 8" TJ ® Rim Board 2.9 3.6 4.3 4.9
Allowable Holes 4 1¼" 1.3E TimberStrand ® LSL 3.5 4.3 5.1 5.8 6.6 7.3 8.0 8.8
Exterior Deck Attachment 5 1½" 1.3E TimberStrand ® LSL 4.2 5.2 6.1 7.0 7.9 8.8 9.6 10.5
Header Application 5 1¾" 1.55E TimberStrand ® LSL 5.2 6.5 7.7 8.8
Allowable Vertical Loads 5 3½" 1.55E TimberStrand ® LSL 10.4 13.0 15.3 17.5
Load Tables:
1-Ply Rim Board 6
2-Ply Rim Board 7
Multiple-Member Connections 7
PRODUCT STORAGE
Protect product from sun and water
CAUTION:
Wrap is slippery when wet or icy
ist.com
TrusJo 3.8358
888.45
om om
oist.c oist.c 58
TrusJ453.8358 TrusJ 53.83 m
888. 888.4 ist.co58
TrusJo53.83
m
t.co 8
Jois .835
Trus.453
888
Trus453.
888.
.com
Joist8358
directly over support blocks
Wind force on a wall is resisted Wall is supported at top by roof Load in roof and floor diaphragms is Side walls act as shear force
by wall sheathing and framing. diaphragm and at bottom by t ransferred to side walls (or braced/shear collectors. Loads may accumulate
floor diaphragm. walls) by rim board, rim joist, or blocking. from top of house to bottom.
Connections are essential to transfer load.
How do lateral capacities of 11⁄4" TimberStrand® LSL rim board compare to sawn lumber framing?
In floor or roof diaphragms, 1¼" TimberStrand® LSL rim board is capable of transferring the same lateral loads allowed by code for 2" nominal framing members. This equivalency
was verified by testing: International Building Code, Case 1, unblocked diaphragm at 240 plf with 23⁄32" sheathing and 8d (0.131" x 21⁄2") nails at 6" on-center.
Wall Framing Boundary Nailing Per code Per code 8d (0.131" x 21/2") at 6" o.c. 8d (0.131" x 21/2") at 4" o.c.
Intermediate Nailing 8d (0.131" x 21/2") at 12" o.c.
Maximum Lateral Load (plf) 220(5) 300(5) 350(6) 560(6)
(1) All sheathing must be properly blocked and nailed. (4) Sheathing must be continuous over all plate-to-plate and plate-to-rim board interfaces and
(2) Verify the lateral capacity of the wall. Not all types of code-allowed wall construction may butt together at mid-depth of rim board as shown in A3.4. At foundation, fasten the
provide the same lateral resistance. Check with your local building officials or the design bottom edge of the sheathing to the sill plate.
professional of record. (5) Maximum lateral load capacities are for seismic design applications. No further increases
(3) Detail A3.3 must be a segmented wall, location of full-height structural sheathing per code. for duration of load are allowed, except loads may be increased by a factor of 1.4 for wind
design applications.
(6) Capacities must not be increased for duration of load.
ALLOWABLE HOLES
Minimum distance from end of rim: Do not locate holes under Do not locate holes over
2x diameter (D) for round holes, concentrated loads such as, clear openings wider than 24"
3x length (L) for rectangular holes trimmers or columns when rim is used as a header
2x_ bottom plate
1" min.
D1 Max. 2/3 L1 L2
rim depth
D2
2 x D1
min. 2x_ double Closely grouped round holes are
top plate 3 x L1 Opening > 24"
2x_ wall studs permitted if the group perimeter meets
min.
requirements for round or square holes.
General Notes
• Permissible Hole Sizes: • The horizontal distance between the end of the rim and the edge of the hole must
Round hole with diameter not exceeding 2/3 rim board depth, centered vertically. be at least twice the diameter for a round hole and three times the hole length for
Square or rectangular hole with the largest dimension not exceeding 2/3 rim board a rectangular hole.
depth, centered vertically. • Do not over cut rectangular holes.
14'' long rectangular hole with minimum 3½'' clearance from the top edge and 2''
from the bottom edge. • Maintain at least 1" from the edge of a floor joist.
• The horizontal distance between the edges of adjacent round holes must be at least • Do not locate holes under concentrated loads or where rim is used as a header
twice the diameter of the largest adjacent round hole, and three times the length of the that clear spans more than 24".
largest adjacent rectangular hole.
HEADER APPLICATION
Locate joint a minimum
of 12" beyond opening Rim board joint
)
ing
open
h
oug
n (r
Spa
* Indicates Total Load value controls. See How to Use This Table and General Notes on page 6.
You want to build solid and durable structures—we want to help. Weyerhaeuser
provides high-quality building products and unparalleled technical and field
assistance to support you and your project from start to finish.
Floors and Roofs: Start with the best framing components in the industry: our
Trus Joist® TJI® joists; TimberStrand® LSL rim board; and TimberStrand® LSL,
Microllam® LVL, and Parallam® PSL headers and beams. Pull them all together
with our self-gapping and self-draining Weyerhaeuser Edge GoldTM floor panels and
durable Weyerhaeuser roof sheathing.
Walls: Get the best value out of your framing package—use TimberStrand® LSL
studs for tall walls, kitchens, and bathrooms, and our traditional, solid-sawn
lumber everywhere else. Cut down installation time by using TimberStrand® LSL
headers for doors and windows, and Weyerhaeuser wall sheathing with its handy
two-way nail lines.
Software Solutions: Whether you are a design professional or lumber dealer,
Weyerhaeuser offers an array of software packages to help you specify individual
framing members, create cut lists, manage inventories—even help you design a
complete structural frame. Contact your Weyerhaeuser representative to find out
how to get the software you need.
Technical Support: Need technical help? Weyerhaeuser has one of the largest
networks of engineers and sales representatives in the business. Call us for help,
and a skilled member from our team of experts will answer your questions and work
with you to develop solutions that meet all your structural framing needs.
CONTACT US
1.888.453.8358 • weyerhaeuser.com/woodproducts/contact
LIMITED LIFETIME
PRODUCT WARRANTY
Contact your local representative or dealer at:
Weyerhaeuser provides a limited warranty for the expected life of the structure for all Trus Joist® branded
products. Product information, installation instructions, and the full text of each product's limited warranty
(including limitations and exclusions) are available on the Weyerhaeuser website, from your Weyerhaeuser
representative, or by calling toll free: 888-453-8358.
Additionally, Weyerhaeuser offers limited warranties on a broad variety of its other products. To see
complete details of all Weyerhaeuser product warranties, visit weyerhaeuser.com/wood products/warranty.
1.888.453.8358 WEYERHAEUSER.COM/WOODPRODUCTS
Reorder TJ-1010 December 2016 , Weyerhaeuser, and Trus Joist are registered trademarks of Weyerhaeuser NR. © 2016 Weyerhaeuser NR Company. All rights reserved.