Professional Documents
Culture Documents
Byju's Practice Workshop: Topic Covered: Units and Dimensions
Byju's Practice Workshop: Topic Covered: Units and Dimensions
Topic covered:
Units and Dimensions
1. The mass of liquid flowing per second per unit area of cross section of the tube is
proportional to P x and v y , where P is the pressure difference and v is the velocity, then
the relation between x and y is
a. x = y b. x = −y
c. y = x
2
d. y = −x 2
Ax1/2
2. The potential energy of a particle varies with distance x as U = , where A and B are
x2 +B
constants. The dimensional formula for A × B is
7 11
a. M1 L2 T −2 b. M1 L 2 T −2
5 9
c. M1 L2 T −2 d. M1 L2 T −2
3. If α kilogram, β meter, and γ second are the fundamental units, 1 cal can be expressed in
new units as [1 cal = 4.2 J]
a. α−1 β2 γ b. α−1 β−2 γ
c. 4.2 α−1 β d. 4.2 α−1 β−2 γ2
4. Using the concept of significant figures, match Column I with the correct number of
significant figures in Column II
Column I Column II
i. 0.1234 a. 5
ii. 1.2100 cm b. 4
iv. 3 × 108 d. 2
The Van Der Waal’s equation of state for some gases can be expressed as:
a
(P + 2 ) (V − b) = RT
V
Where P is the pressure, V is the molar volume and T is the absolute temperature of the
given sample of gas and a, b and R are constants.
7. Which of the following does not have the same dimension formula as that of RT?
a. PV b. Pb
a ab
c. d.
V2 V2
10. In an instrument, there are 25 divisions on the vernier scale which coincides with 24th
division of the main scale. 1 cm on main scale is divided into 20 equal parts. The least
count of the instrument is
a. 0.002 cm b. 0.05 cm
c. 0.001 cm d. 0.02 cm
Column I Column II
13. A screw gauge with a pitch of 0.5 mm and a circular scale with 50 divisions is used to
measure the thickness of a thin sheet of Aluminium. Before starting the measurement, it
is found that when the two jaws of the screw gauge are brought in contact, the 45th
division coincides with the main scale line and that the zero of the main scale is barely
visible. What is the thickness of the sheet if the main scale reading is 0.5 mm and the 25th
division coincides with the main scale line?
a. 0.50 𝑚𝑚 b. 0.75 𝑚𝑚
c. 0.80 𝑚𝑚 d. 0.70 𝑚𝑚
14. A highly rigid cubical block A of small mass M and side L is fixed rigidly onto another
cubical block B of the same dimensions and of modulus of rigidity η such that the lower
face of A completely covers the upper face of B. The lower face of B is rigidly held on a
horizontal surface. A small force F is applied perpendicular to one of the side faces of A.
After the force is withdrawn block A executes small oscillations. The time period of which
is given by
𝑀𝜂 𝐿
a. 2𝜋√ b. 2𝜋√𝑀𝜂
𝐿
𝑀𝐿 𝑀
c. 2𝜋√ 𝜂 d. 2𝜋√𝜂𝐿
a. 0 b. 2
c. −2 d. 1
16. The energy of a system as a function of time t is given as 𝐸(𝑡) = 𝑒 −𝛼𝑡 𝐴2 , where 𝛼 =
0.2𝑠 −1 . The measurement of 𝐴 has an error of 1.25%. If the error in the measurement of
time is 1.50%, the percentage error in the value of 𝐸(𝑡) at t = 5s is _______.
17. If force, time and velocity are treated as fundamental quantities, then dimensional
formula of energy will be
a. [𝐹𝑇𝑉] b. [𝐹𝑇 2 𝑉]
c. [𝐹𝑇𝑉 2 ] d. [𝐹T 2 𝑉 2 ]
18. The dimensions of the quantities in one (or more) of the following pairs are the same.
Identify the pair(s).
𝑉
19. The resistance R = where V=100 ± 5 volts and 𝐼 =10 ± 0.3 amperes. Calculate the
𝐼
percentage error in R.
a. 8 % b. 10 %
c. 12% d. 14%
20. Test which of the following equations are dimensionally correct. (S = surface tension,
𝜌 = density, 𝑃 = pressure, V = volume, 𝑛 = coefficient of viscosity, 𝑟 = radius, 𝑣 = velocity,
𝑡 = time, 𝑙 = length, H = height)
2𝑆 𝑐𝑜𝑠 𝜃
a. H = b. 𝑣 = √𝜌
𝑃
𝜌𝑟𝑔
c. V =
𝜋𝜌𝑟 4 𝑡 d. All correct
8𝑛𝑙
a. be dimensionless
b. have dimensions of 𝑇 −2
c. have dimensions of P
d. have dimensions of P multiplied by 𝑇 −2
22. If the units of length and force are increased four times, then the unit of energy will
a. increase 8 times b. increase 16 times
c. decrease 16 times d. increase 4 times
23. In a particular system, the unit of length, mass and time are chosen to be 10 𝑐𝑚, 10 𝑔𝑚
and 0.1𝑠 respectively. The unit of force in this system will be equivalent to
a. 1/10 𝑁 b. 1 𝑁
c. 10 𝑁 d. 100 𝑁
ANSWER KEY
Question
Number 1 2 3 4 5 6 7 8 9
Correct (i – b; ii –
Answer (b, c, d) (b) (d) a; iii – d; (a) (c) (c) (c) (d)
iv – c)
Question
Number 10 11 12 13 14 15 16 17
Correct (i – c; ii –
Answer (d) (a) a; iii – b) (c) (d) (b) 3 (a)
Question
Number 18 19 20 21 22 23
Correct
Answer (a, d) (a) (a, b) (b) (b) (a)