Professional Documents
Culture Documents
General Description: P. 1 2003/5 Ver. 1.7
General Description: P. 1 2003/5 Ver. 1.7
1. General Description
A/D converter module:
This EPROM-Based 8-bit micro-controller uses a fully -Four analog inputs multiplexed into one A/D
static CMOS technology process to achieve higher converter
speed and smaller size with the low power -8-bit resolution
consump-tion and high noise immunity. On chip 4 types of oscillator can be selected by
memory incl-udes 1K words of ROM, and 68 bytes of programming option:
static RAM. RC-Low cost RC oscillator
LFXT-Low frequency crystal oscillator
2. Features XTAL-Standard crystal oscillator
HFXT-High frequency crystal oscillator
The followings are some of the features on the 8-bit real time clock/counter(RTCC) with 8-bit
hardware and software : programmable prescaler
Fully COMS static design On-chip RC oscillator based Watchdog
8-bit data bus Timer(WDT)
On chip EPROM size : 1.0 K words 13 I/O pins with their own independent
Internal RAM size : 84 bytes direction control
(68 general purpose registers, 16 special
registers) 3. Applications
37 single word instructions
14-bit instructions The application areas of this MDT2051 range from
8-level stacks appliance motor control and high speed automotive
Operating voltage : 2.5 V ~ 6.5 V (PRD Disable) to low power remote transmitters/receivers, pointing
4.5 V ~ 6.5 V (PRD Enable) devices, and telecommunications processors, such
Operating frequency : DC ~ 20 MHz as Remote controller, small instruments, chargers,
The most fast execution time is 200 ns under toy, automobile and PC peripheral …etc.
20 MHz in all single cycle instructions except
the branch instruction 4. Pin Assignment
Addressing modes include direct, indirect and
relative addressing modes PA2/AIC2 1 18 PA1/AIC1
Power-on Reset PA3/AIC3 2 17 PA0/AIC0
Power edge-detector Reset PA4/RTCC 3 16 OSC1
Power range-detector Reset /MCLR 4 15 OSC2
Sleep Mode for power saving Vss 5 14 Vdd
Four interrupt sources: PB0/INT 6 13 PB7
-External INT pin PB1 7 12 PB6
-TMR0 timer PB2 8 11 PB5
-A/D conversion completion PB3 9 10 PB4
-PortB<7:4> interrupt on change
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw P. 1 2003/5 Ver. 1.7
MDT2051
5. Pin Function Description
Vss Ground
6. Memory Map
BANK0
01 RTCC
02 PCL
03 STATUS
04 MSR
05 Port A
06 Port B
08 ADS0
09 ADRES
0A PCH
0B INTS
BANK1
01 TMR
05 CPIO A
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw P. 2 2003/5 Ver. 1.7
MDT2051
Address Description
06 CPIO B
07 PSTA
08 ADS1
A9 A8 A7~A0
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw P. 3 2003/5 Ver. 1.7
MDT2051
(5) MSR (Memory Bank Select Register) : R4
b7 b6 b5 b4 b3 b2 b1 b0
0 ADRUN 0 : A/D converter module is shut off and consumes no operating current
1 : A/D converter module is operating
1 ADIF A/D conversion complete interrupt flag bit
Set when conversion is completed. Reset in software.
2 GO/DONEB GO/DONEB must be set to begin a conversion . It is automatically reset
in hardware when the conversion is complete
4,3 CHS1-0 00 : AIC0 01 : AIC1 10 : AIC2 11 : AIC3
*Note: determined by OSC mode, HF: fosc/32 XT: fosc/8 RC: fosc/2 LF: fosc/2
Bit Function
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw P. 4 2003/5 Ver. 1.7
MDT2051
(11) INTS ( Interrupt Status Register ) : R0B
0 RBIF PORT B change interrupt flag. Set when PB <7:4> inputs change
1 INTF Set when INT interrupt occurs. INT interrupt flag.
2 TIF Set when TMR overflows.
3 RBIE 0 : disable PB change interrupt
1 : enable PB change interrupt
4 INTS 0 : disable INT interrupt
1 : enable INT interrupt
5 TIS 0 : disable TMR interrupt
1 : enable TMR interrupt
6 ADIS 0 : disable A/D interrupt
1 : enable A/D interrupt
7 GIS 0 : disable global interrupt
1 : enable global interrupt
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw P. 5 2003/5 Ver. 1.7
MDT2051
(13) CPIO A (Control Port I/O Mode Register) : R85
=“ 0” , I/O pin in output mode;
=“ 1” , I/O pin in input mode.
RC Oscillator
HFXT Oscillator
XTAL Oscillator
LFXT Oscillator
Power-range control
Power-range disable
Power-range enable
0ms
80ms
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw P. 6 2003/5 Ver. 1.7
MDT2051
Security Enable
The default security state of EPROM is weak disable. Once the IC was set to
enable or disable, it’ s forbidden to change.
Address Description
000 The starting address of power on, external reset or WDT time-out reset.
IAR 00h - - -
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw P. 7 2003/5 Ver. 1.7
MDT2051
Condition Status: bit 4 Status: bit 3 Status: bit 1 Status: bit 0
Power on reset 1 1 0 X
8. Instruction Set :
Mnemonic
Instruction Code Operands Function Operating Status
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw P. 8 2003/5 Ver. 1.7
MDT2051
Mnemonic
Instruction Code Operands Function Operating Status
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw P. 9 2003/5 Ver. 1.7
MDT2051
9. Electrical Characteristics
*Note: Temperature=25°C
1.Operation Current :
(1) HF (C=10p) , WDT - enable, PRD – disable
Sleep,WDT-disable,
4M 10M 20M Sleep
PRD-disable
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw P. 10 2003/5 Ver. 1.7
MDT2051
Sleep,WDT-disable,
C R Freq. Current
PRD-disable
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw P. 11 2003/5 Ver. 1.7
MDT2051
2. Input Voltage (Vdd = 5V) :
PA,PB Condition
Time
2.5V 25
3.0V 23
4.0V 20
5.0V 18
6.3V 16
Unit = ms
These parameters are for reference only.
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw P. 12 2003/5 Ver. 1.7
MDT2051
6. PRD :
(1)PRD reset voltage :
Voltage
Vh 4.0±5%
Vl 3.6±5%
Unit = V
These parameters are for reference only.
Current
4.0V 100
3.6V 80
Unit = Ua
These parameters are for reference only.
time 720
Unit = ns
These parameters are for reference only.
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw P. 13 2003/5 Ver. 1.7
MDT2051
9.PB pull-high resister
5V 50+-20%Kohm
3V 100+-20%Kohm
These parameters are for reference only.
This specification are subject to be changed without notice. Any latest information please preview
http;//www.mdtic.com.tw P. 14 2003/5 Ver. 1.7