Professional Documents
Culture Documents
JCA Full Set
JCA Full Set
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position cranes, Drive into equipment. Injuries to personnel. Damage to Rigger gives proper hand Rigger/ Truck
Trucks Truck hits personnel in equipments. signal. Good communication. Pusher
Truck Pusher/
the area. Check the area
Rigger
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Rigger/ Truck
equipments Lifting equipment failure. equipments. Inspect all lifting gears for pusher / QSO
Truck Pusher damages.
3. connect Sling on Pinch point, Caught by. Pinched hands and fingers. Use Impact gloves. Keep RAP / A/D / QSO
the load Injuries to personnel. Damage to fingers and hands clear
RAP equipments. between block hook latch and
sling
4. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Clear area under suspended Rigger / A/D /
equipments. load. Only rigger who give QSO
Crane Operators signals
5. Drive truck to Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck driver/
load. Truck Driver / something. equipments. signal. Good communication. Truck Pusher /
Truck Pusher One flag man only. QSO
6. Set load to Trap under load. Caught Injuries to personnel. Damage to Clear area under load. Keep Rigger/RAP / A/D
truck. Rigger / Crane by or swing hit. equipments. feet and legs away from load. / QSO
Operator
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
8. Secure the load Dropped load Damaged equipments Tied and secure tanks before Truck Drivers
Drivers move trucks, check boomers
chain every 50KM
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position trucks Drive into equipment. Injuries to personnel. Damage to Rigger give proper hand Truck Pusher
to where load is to Truck hits personnel in equipments. signal. Good communication.
be loaded. Truck Pusher the area. One flag man only.
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Truck Pusher/
equipments Lifting equipment failure. equipments. Inspect all lifting gears for QSO
Truck Pusher damages.
3. Rig up load to Struck by crane hook Pinched hands and fingers. Use full body harness. Keep Rigger/ RAP / A/D
crane hook block. Caught by. Injuries to personnel. Damage to fingers and hands clear
RAP/AD equipments. between block hook latch and
sling/shackle.
4. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Clear area under suspended Rigger/ RAP / A/D
Rigger/ Crane equipments. load.
Operators
5. Drive back in Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Rigger/ RAP / A/D
under load. Truck Driver / something. equipments. signal. Good communication.
RAP One flag man only.
6. Set load to Trap under load. Caught Injuries to personnel. Damage to Use tag line. Clear area under Rigger
truck. Rigger / Crane by or swing hit. equipments. load. Keep feet and legs away
Operator from load.
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. Rigger/ RAP / A/D
equipment. RAP Attach lanyard and secure
self from fall.
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Permit No : Task : Load Unload Chemical box with Cranes (TANDEM LIFT)
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position cranes, Drive into equipment. Injuries to personnel. Damage to Rigger gives proper hand Rigger/ Truck
Trucks Truck hits personnel in equipments. signal. Good communication. Pusher
Truck Pusher/
the area. Check the area
Rigger
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Rigger/ Truck
equipments Lifting equipment failure. equipments. Inspect all lifting gears for Pusher / QSO
Truck Pusher damages.
3. connect Sling on Pinch point, Caught by. Pinched hands and fingers. Use Impact gloves. Keep RAP / A/D / QSO
the Box Injuries to personnel. Damage to fingers and hands clear
RAP equipments. between block hook latch and
sling
4. Pick up Box. Load swing. Load falls. Injuries to personnel. Damage to Clear area under suspended Rigger / QSO
equipments. load. Only rigger who give
Crane Operators signals
5. Drive truck to Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck driver /
load. Truck Driver / something. equipments. signal. Good communication. Truck Pusher
Truck Pusher One flag man only. QSO
6. Set load to Trap under load. Caught Injuries to personnel. Damage to Clear area under load. Keep Rigger/RAP / A/D
truck. Rigger / Crane by or swing hit. equipments. feet and legs away from load. / QSO
Operator
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
8. Secure the Dropped load Damaged equipments Tied and secure tanks before Truck Drivers
tanks Drivers move trucks, check boomers
chain every 50KM
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position trucks Drive into equipment. Injuries to personnel. Damage to Banks man give proper hand Truck Pusher/
to where load is to Truck hits personnel in equipments. signal. Good communication. Truck Driver
Truck Pusher/
be loaded. the area. One flag man only.
Truck Driver
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Truck Pusher /
equipments Lifting equipment failure. equipments. Inspect all lifting gears for QSO
Truck Pusher damages.
3. Rig up load to Struck by crane hook Pinched hands and fingers. Use full body harness. Keep RAP / A/D / QSO
crane hook block. Caught by. Injuries to personnel. Damage to fingers and hands clear
RAP equipments. between block hook latch and
sling/shackle.
4. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Use tag line. Counter pull on Rigger / QSO
equipments. swing motion. Clear area
Crane Operator under suspended load.
5. Drive back in Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Rigger/ Truck
under load. Truck Driver / something. equipments. signal. Good communication. Pusher / QSO
RAP One flag man only.
6. Set load to Trap under load. Caught Injuries to personnel. Damage to Use tag line. Clear area under Rigger / QSO
truck. Rigger / Crane by or swing hit. equipments. load. Keep feet and legs away
Operator from load.
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Permit No : Task : Load/ Unload Drill pipe box with Cranes (TANDEM LIFT)
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position trucks Drive into equipment. Injuries to personnel. Damage to Banks man give proper hand Truck Pusher
to where load is to Truck hits personnel in equipments. signal. Good communication.
be loaded. Truck Pusher the area. One flag man only.
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Truck Pusher /
equipments Lifting equipment failure. equipments. Inspect all lifting gears for QSO
Truck Pusher damages.
3. Rig up load to Struck by crane hook Pinched hands and fingers. Use full body harness. Keep RAP / A/D / QSO
crane hook block. Caught by. Injuries to personnel. Damage to fingers and hands clear
RAP equipments. between block hook latch and
sling/shackle.
4. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Use tag line. Counter pull on RAP / A/D / QSO
equipments. swing motion. Clear area
Crane Operator under suspended load.
5. Drive back in Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck Pusher /
under load. Truck Driver / something. equipments. signal. Good communication. Truck Driver/
Truck Pusher One flag man only. QSO
6. Set load to Trap under load. Caught Injuries to personnel. Damage to Use tag line. Clear area under Rigger / QSO
truck. Rigger / Crane by or swing hit. equipments. load. Keep feet and legs away
Operator from load.
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position cranes, Drive into equipment. Injuries to personnel. Damage to Rigger gives proper hand Rigger/ Truck
Trucks Truck hits personnel in equipments. signal. Good communication. Pusher
Rigger/ Truck
the area. Check the area
Pusher
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Rigger/ Truck
equipments Lifting equipment failure. equipments. Inspect all lifting gears for Pusher / QSO
Truck Pusher damages.
3. connect Sling on Pinch point, Caught by. Pinched hands and fingers. Use Impact gloves . Keep RAP / A/D / QSO
the load Injuries to personnel. Damage to fingers and hands clear
RAP equipments. between block hook latch and
sling
4. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Clear area under suspended Rigger / QSO
equipments. load. Only rigger who give
Crane Operators signals
5. Drive truck to Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck Driver/
load. Truck Driver / something. equipments. signal. Good communication. Truck Pusher /
Truck Pusher One flag man only. QSO
6. Set load to Trap under load. Caught Injuries to personnel. Damage to Clear area under load. Keep Rigger / QSO
truck. Rigger / Crane by or swing hit. equipments. feet and legs away from load.
Operator
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
8. Secure the load Dropped load Damaged equipments Tied and secure tanks before Truck Drivers
Drivers move trucks, check boomers
chain every 50KM
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position cranes, Drive into equipment. Injuries to personnel. Damage to Rigger gives proper hand Rigger/ Truck
Trucks Truck hits personnel in equipments. signal. Good communication. Pusher
Truck Pusher the area. Check the area
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Rigger/ Truck
equipments Lifting equipment failure. equipments. Inspect all lifting gears for Pusher/ QSO
Truck Pusher damages.
3. connect Sling on Pinch point, Caught by. Pinched hands and fingers. Use Impact gloves . Keep RAP / A/D / QSO
the koomy Injuries to personnel. Damage to fingers and hands clear
RAP equipments. between block hook latch and
sling
4. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Clear area under suspended Rigger / QSO
equipments. load. Only rigger who give
Crane Operators signals
5. Drive truck to Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck Driver /
load. Truck Driver / something. equipments. signal. Good communication. Truck Pusher/
Truck Pusher One flag man only. QSO
6. Set load to Trap under load. Caught Injuries to personnel. Damage to Clear area under load. Keep Rigger / QSO
truck. Rigger / Crane by or swing hit. equipments. feet and legs away from load.
Operator
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
8. Secure the Dropped load Damaged equipments Tied and secure tanks before Truck Drivers
koomy Drivers move trucks, check boomers
chain every 50KM
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Permit No : Task : Load Drill pipe box with Cranes (TANDEM LIFT)
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position trucks Drive into equipment. Injuries to personnel. Damage to Banks man give proper hand Truck Pusher/
to where load is to Truck hits personnel in equipments. signal. Good communication. Truck Driver
Truck Driver/
be loaded. the area. One flag man only.
Truck Pusher
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Truck Pusher /
equipments Lifting equipment failure. equipments. Inspect all lifting gears for QSO
Truck Pusher damages.
3. Rig up load to Struck by crane hook Pinched hands and fingers. Use full body harness. Keep RAP / A/D / QSO
crane hook block. Caught by. Injuries to personnel. Damage to fingers and hands clear
RAP equipments. between block hook latch and
sling/shackle.
4. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Use tag line. Counter pull on Rigger / QSO
Crane Operator/ equipments. swing motion. Clear area
Rigger under suspended load.
5. Drive back in Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck Pusher /
under load. Truck Driver / something. equipments. signal. Good communication. QSO
Truck Pusher One flag man only.
6. Set load to Trap under load. Caught Injuries to personnel. Damage to Use tag line. Clear area under Rigger / QSO
truck. Rigger / Crane by or swing hit. equipments. load. Keep feet and legs away
Operator from load.
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position cranes, Drive into equipment. Injuries to personnel. Damage to Rigger gives proper hand Rigger/ Truck
Trucks Truck hits personnel in equipments. signal. Good communication. Pusher
Rigger/ Truck
the area. Check the area
Pusher
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Truck Pusher /
equipments Lifting equipment failure. equipments. Inspect all lifting gears for QSO
Truck Pusher damages.
3. connect Sling on Pinch point, Caught by. Pinched hands and fingers. Use Impact gloves . Keep RAP / A/D / QSO
the tank Injuries to personnel. Damage to fingers and hands clear
RAP equipments. between block hook latch and
sling
4. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Clear area under suspended Rigger / QSO
equipments. load. Only rigger who give
Crane Operators signals
5. Drive truck to Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck Pusher /
load. Truck Driver / something. equipments. signal. Good communication. QSO
Truck Pusher One flag man only.
6. Set load to Trap under load. Caught Injuries to personnel. Damage to Clear area under load. Keep Rigger / QSO
truck. Rigger / Crane by or swing hit. equipments. feet and legs away from load.
Operator
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
8. Secure the tank Dropped load Damaged equipments Tied and secure tanks before Truck Drivers
Drivers move trucks, check boomers
chain every 50KM
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position cranes, Drive into equipment. Injuries to personnel. Damage to Rigger gives proper hand Rigger/ Truck
Trucks Truck hits personnel in equipments. signal. Good communication. Pusher
Truck Pusher/
the area. Check the area
Rigger
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Truck Pusher /
equipments Lifting equipment failure. equipments. Inspect all lifting gears for QSO
Truck Pusher damages.
3. connect Sling on Pinch point, Caught by. Pinched hands and fingers. Use Impact gloves. Keep RAP / A/D / QSO
the boxes Injuries to personnel. Damage to fingers and hands clear
RA/ A/D equipments. between block hook latch and
sling
4. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Clear area under suspended Rigger / QSO
equipments. load. Only rigger who give
Crane Operators signals
5. Drive truck to Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck Pusher /
load. Truck Driver / something. equipments. signal. Good communication. QSO
Truck Pusher One flag man only.
6. Set load to Trap under load. Caught Injuries to personnel. Damage to Clear area under load. Keep Rigger / QSO
truck. Rigger / Crane by or swing hit. equipments. feet and legs away from load.
Operator
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
8. Secure the Dropped load Damaged equipments Tied and secure tanks before Truck Drivers
boxes Drivers move trucks, check boomers
chain every 50KM
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
3. Set Cranes Load failed, drooped Wrong job being done PTW/TBT Truck Pusher
position crane failed Personnel can get injured Insure it is understood by all Rigger 1
while Propriety damage crew members involved in the
job.
Rigger Correct crane position
Rigger 1 only will give signal
to crane operator(If
necessary) Use of taglines
for the load
4. connect Sling on Pinch point, Caught by. Pinched hands and fingers. Use Impact gloves . Keep RAP / A/D / QSO
load Injuries to personnel. Damage to fingers and hands clear
equipments. between block hook latch and
RAP sling
7.Closed out PTW Injury to personnel Wrong job being done Supervisor responsible for the DR/AD
Pinch points, Fall, Slip, Personnel can get injured PTW to be closed out.
Trip hazards while rigging down pins beams
DR/AD
Dropped objects Equipments can get damage
Equipment Damage
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position cranes, Drive into equipment. Injuries to personnel. Damage to Rigger gives proper hand Rigger/ Truck
Trucks Truck hits personnel in equipments. signal. Good communication. Pusher
Rigger/ Truck
the area. Check the area
Pusher
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Rigger / QSO
equipments Lifting equipment failure. equipments. Inspect all lifting gears for
Truck Pusher damages.
3. connect Sling on Pinch point, Caught by. Pinched hands and fingers. Use Impact gloves . Keep RAP / A/D / QSO
the Skid Injuries to personnel. Damage to fingers and hands clear
RAP equipments. between block hook latch and
sling
4. Pick up Skid Load swing. Load falls. Injuries to personnel. Damage to Clear area under suspended Rigger / QSO
equipments. load. Only rigger who give
Crane Operators signals
5. Drive truck to Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck Pusher /
load. Truck Driver / something. equipments. signal. Good communication. QSO
Truck Pusher One flag man only.
6. Set Skid to Trap under load. Caught Injuries to personnel. Damage to Clear area under load. Keep Rigger / QSO
truck. Rigger / Crane by or swing hit. equipments. feet and legs away from load.
Operator
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
8. Secure the Dropped load Damaged equipments Tied and secure tanks before Truck Drivers
tanks Drivers move trucks, check boomers
chain every 50KM
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Permit No : Task : Load Unload Dog House with Cranes (Tandem Lift)
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position trucks Drive into equipment. Injuries to personnel. Damage to Rigger give proper hand Rigger/ Truck
to where load is to Truck hits personnel in equipments. signal. Good communication. Pusher / A/D
be loaded. Truck Pusher the area. One flag man only.
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Rigger/ RAP / A/D
equipments Rigger/ Truck Lifting equipment failure. equipments. Inspect all lifting gears for
Pusher damages.
3. Rig up Dog Struck by crane hook Pinched hands and fingers. Use full body harness. Keep Rigger/ RAP / A/D
House to crane block. Caught by. Injuries to personnel. Damage to fingers and hands clear
hook RAP/AD equipments. between block hook latch and
sling/shackle.
4. Pick up Dog Load swing. Load falls. Injuries to personnel. Damage to Clear area under suspended Rigger/ RAP / A/D
House. Rigger/ Crane equipments. load.
Operators
5. Drive back in Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Rigger/ Trcuk
under load. Truck Driver / something. equipments. signal. Good communication. Pusher
Truck Pusher One flag man only.
6. Set load to Trap under load. Caught Injuries to personnel. Damage to Use tag line. Clear area under Rigger/ Truck
truck. Rigger / Crane by or swing hit. equipments. load. Keep feet and legs away Pusher
Operator from load.
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. Rigger/ RAP / A/D
equipment. RAP Attach lanyard and secure
self from fall.
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
7. Secure all lines, Falling objects. Struck-by While travelling loose cables, Tie-off all cables and slings. TP / Driller
cables, slings, etc. or hit by. Dangling cables slings, shackles, pins etc, drops Double check all shackles and
AD / RAP
and slings. Loose and hits other vehicles and pins and the mast for any
objects. personnel. loose objects.
Contingency Plans “”What to do if something goes wrong?”
1. Provide first aid.
2. Seek additional medical care from medic.
3. For serious accident, alert supervisors for emergency purposes.
4.
5.
Supervisor’s Name : Signature :
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the remedial
actions to be taken to eliminate, reduce or control the hazards.
Crew’s Name and Signature
1. 5.
2. 6.
3. 7.
Rig No : UTMN 1644
Job Safety Plan (JSP) Page No :1
Permit No : Task : Raising Mast
Prepared By : Sign : Date :
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Conduct Pre-job Miscommunication. Panic. Serious physical injuries. Discuss all potential hazards. Driller / AD / QSO
safety meeting Personnel unaware of Property damage and lost. Review PTW. Designate / TP
with crew and TP operation and Procedures not followed as personnel for specific job.
raise PTW. procedures. Dropped planned.
derrick.
2. Secure Bridal Bridal line not attached. Bridal line disengage while raising Wear full body harness, one TP / Driller
Bridal line out of derrick. Severe damage on bridal flag man and designate a n
TP / QSO sheaves. Personnel falls. lines. Damage sheaves. Serious experienced man rider winch
physical injuries. operator. Secure bridal line as
per DOP/DOI.
3. Position all Trapped and caught Rollers, sheaves and moving Make sure designated TP / AD
watchmen in their cables, slings. Sheaves mechanical parts stuck or caught. personnel watch closely his
post and rollers stuck. Falling Equipment damage. Personnel post. Stop operation for any
objects. struck by falling objects. Slings and unusual thing. Keep clear from
TP / Drl
cables catching against parts. drop area and under the
derrick. Tie-off all cables and
wire rope before lowering the
derrick.
4. Engage Draw Uncontrolled speed. Drill Drill line snags due to fast speed Set draw works speed to TP / Driller
works and line snags. while raising derrick. Major appropriate level. Continues
lower mast TP / Drl equipment and property lost. and channelled
slowly Fatalities. communication between
personnel.
6. Set Derrick and Struck by flying objects. Pins hits personnel. Tools Clear area below. Use tie-off TP / Driller
lock in pins. Fall, smash hands and dropping below. Personnel slips rope to secure pin, hammer,
TP / Drl
fingers. No Full Body and falls. Serious physical injuries. tools, etc. Wear full body
Harness. harness.
Contingency Plans “”What to do if something goes wrong?”
1. Provide first aid.
2. Seek additional medical care from medic.
3. For serious accident, alert supervisors for emergency purposes.
4.
5.
4. Secure / remove Struck by, hit by, drop Serious physical injuries. Damage Remove any debris – be DM
stabbing board loose items, equipments, equipments. High-potential aware of any person who may
Secure monkey slip and fall incident be working under you – use
board and fingers fall protection
Secure with at least three (3)
Derrick man ropes or remove completely
Fall protection secured –
secure monkey board and
finger with at least two (2)
ropes
5. Check again for Struck by, hit by, drop Serious physical injuries. Damage Remove anything that may fall DM / FM
debris and check Derrick man / loose items, equipments, equipments. High-potential when derrick is lowered –
the rig lights, Floor man slip and fall incident always use fall protection
secure safety Fall protection equipment –
cables, check secure / remove any debris
sheave and drill
line
6. Pass air hoist Struck by – falls Serious physical injuries. Damage Right tool for the job DM / FM
line through derrick Dropping loose items, equipments. High-potential Fall protection equipment –
above monkey equipments, slip and fall. incident secure / remove any debris
board (after rig Floor men Remove anything that may fall
floor is secured) when derrick is lowered –
always use fall protection
7. Secure all lines, Struck by – falls Serious physical injuries. Damage Right tool for the job DM / FM
cables, wire ropes, Dropping loose items, equipments. High-potential Fall protection equipment –
ladders equipments, slip and fall. incident secure / remove any debris
Floor men Remove anything that may fall
when derrick is lowered –
always use fall protection
4. Watch for open lines Slips and falls, pinch points, Pinched fingers, smashed / trap Proper hand and body placement. Firm footing. AD / Derrick man
AD / Derrick
when flushing mud.(If trapped pressure, overexertion, hands and bodily parts. Back strains. Use tie-off ropes. Good communication. Keep clear
man
applicable) equipment damage. Struck by of pinch and trap area.
5. Attachment of slings Slips and falls, pinch points, Pinched fingers, smashed / trap Proper hand and body placement. Firm footing. AD / Derrick
AD / Derrick
on the lifting point of overexertion, equipment hands and bodily parts. Back strains. Use tie-off ropes. Good communication. Keep clear man/RA/RAP
man/RA/RAP
the mud tanks. damage. Struck by of pinch and trap area.
4. Closed work permit Slips and falls, pinch points, Pinched fingers, smashed / trap Proper hand and body placement. Manual handling A/D; C/E; D/M
trapped pressure, overexertion, hands and bodily parts. Back strains. / lifting techniques. Use proper tools for the job.
AD; D/M
equipment damage. Struck by Keep away from swing area. Team work. Make
sure work permit is properly closed.
Contingency Plans “”What to do if something goes wrong?”
1. Stop the job, inform supervisor.
2. Provide first aide, evacuate personnel from area.
3. Call Medics attention to provide additional medical assessment.
Supervisor’s Name : Signature :
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the remedial
actions to be taken to eliminate, reduce or control the hazards.
Crew’s Name and Signature
1. 5.
2. 6.
3. 7.
Rig No :
Job Safety Plan (JSP) Page No :
Permit No : Task : Rig Down/Rig Up Substructure
Prepared By : Sign : Date :
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. PTW/TBT Miss Communication Wrong job being done PTW/TBT TP/DR/AD
Injury to personnel Personnel can get injured Insure it is understood by all
DR/AD
Equipment Damage while rigging down pins beams crew members involved in the
Equipments can get damage job.
2. Removal of pins Injury to personnel Pins can hit someone below PTW/TBT TP/DR/AD
Pinch points, Fall, Slip, Pinch points, Falling Insure it is understood by all
DR/AD/FM Trip hazards crew members involved in the
Dropped objects job.
Correct hand placement
3. Raising of the Injury to personnel Wrong job being done PTW/TBT TP/DR/AD
beams Pinch points, Fall, Slip, Personnel can get injured Insure it is understood by all Rigger 1(If
Trip hazards while rigging down pins beams crew members involved in the necessary)
Dropped objects Equipments can get damage job.
DR/AD/FM Equipment Damage Correct hand placement
Rigger 1 only will give signal
to crane operator(If
necessary) Use of taglines
for the load
4. Loading at the Injury to personnel Wrong job being done PTW/TBT TP/DR/AD
truck Pinch points, Fall, Slip, Personnel can get injured while Insure it is understood by all Rigger 1(If
Trip hazards rigging down pins beams crew members involved in the necessary)
Dropped objects Equipments can get damage job. Correct hand placement
DR/AD/FM Equipment Damage Rigger 1 only will give signal
Truck to crane operator(If
Pusher/Truck necessary) Truck pusher to
Driver assist on the load being
loaded at the truck. Good
communication with the driver
and rigger 1. Use of taglines
for the load
5.Closed out PTW Injury to personnel Wrong job being done Supervisor responsible for the DR/AD
Pinch points, Fall, Slip, Personnel can get injured PTW to be closed out.
Trip hazards while rigging down pins beams
DR/AD
Dropped objects Equipments can get damage
Equipment Damage
3. Rig up load to Struck by crane hook Pinched hands and fingers. . Keep fingers and hands RAP / A/D / QSO
crane hook block. Caught by. Injuries to personnel. Damage to clear between block hook
RAP
equipments. latch and sling/shackle.
4. Pick up Load swing. Load falls. Injuries to personnel. Damage to Clear area under suspended Rigger / QSO
Drawwork. Rigger/ Crane equipments. load.
Operator
4. Set lock pins, Struck by flying objects. Pin hits personnel. Tools dropping Clear area below. Use tie-off TP / Driller
Secure draw works Fall, smash hands and below. Personnel slip and fall. rope to secure pin, hammer,
TP / Driller
fingers. Serious physical injuries. tools, etc. Wear full body
harness.
5. Remove unused Falling objects. Struck-by Loose Pins, shackles, pins etc, Tie-off all cables and slings. TP / Driller
tools or hit by. Dangling cables drops and hits other vehicles and Double check all shackles and
AD / RAP
and slings. Loose personnel. pins and the mast for any
objects. loose objects.
Contingency Plans “”What to do if something goes wrong?”
1. Stop the job
2. Reassessment of the task and job at hand according to risks and hazards
3. Conduct TBT and Plan new strategies accordingly.
4. If there are some injuries, immediately call for help and provide first aid.
5. Medevac the patient to nearest medical facilities
Supervisor’s Name : Signature :
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the remedial
actions to be taken to eliminate, reduce or control the hazards.
Crew’s Name and Signature
1. 5.
2. 6.
3. 7.
Rig No :
Job Safety Plan (JSP) Page No :
Permit No : Task : Un Load Sub Base using Three cranes
Prepared By : Sign : Date :
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. PTW/TBT Miss Communication Wrong job being done PTW/TBT Truck Pusher
Injury to personnel Personnel can get injured while Insure it is understood by all
Truck Pusher
Equipment Damage rigging down pins beams crew members involved in the
Equipments can get damage job.
2. Inspect GLG Injury to personnel, Set base dropped, Serious injures PTW/TBT TP/DR/AD
slings Truck Pusher/ Dropped objects, Load Good visual inspection of
Driller/ A/D failed GLG
3. Set Cranes Load failed, drooped Wrong job being done PTW/TBT Truck Pusher
position crane failed Personnel can get injured Insure it is understood by all Rigger 1
while Propriety damage crew members involved in the
job.
Rigger Correct crane position
Rigger 1 only will give signal
to crane operator(If
necessary) Use of taglines
for the load
4. connect Sling Pinch point, Caught by. Pinched hands and fingers. Use Impact gloves . Keep RAP / A/D / QSO
on load Injuries to personnel. Damage to fingers and hands clear
equipments. between block hook latch and
RAP sling
7.Closed out PTW Injury to personnel Wrong job being done Supervisor responsible for the DR/AD
Pinch points, Fall, Slip, Personnel can get injured PTW to be closed out.
Trip hazards while rigging down pins beams
DR/AD
Dropped objects Equipments can get damage
Equipment Damage
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position trucks Drive into equipment. Injuries to personnel. Damage to Banks man give proper hand Truck Pusher/
to where load is to Truck hits personnel in equipments. signal. Good communication. Truck Driver
be loaded. Truck Pusher the area. One flag man only.
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Truck Pusher /
equipments Lifting equipment failure. equipments. Inspect all lifting gears for QSO
Truck Pusher damages.
3. Rig up load to Struck by crane hook Pinched hands and fingers. Use full body harness. Keep RAP / A/D / QSO
crane hook block. Caught by. Injuries to personnel. Damage to fingers and hands clear
RAP equipments. between block hook latch and
sling/shackle.
4. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Use tag line. Counter pull on Rigger / QSO
equipments. swing motion. Clear area
Crane Operator under suspended load.
5. Move out the Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck Pusher/
Truck Truck Driver / something. equipments. signal. Good communication. QSO
Truck Pusher One flag man only.
6. Set tanks on the Trap under load. Caught Injuries to personnel. Damage to Clear area under load. Keep Rigger / QSO
ground Rigger / Crane by or swing hit. Spill equipments. environmental feet and legs away from load.
Operator damage Spill kit
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position trucks Drive into equipment. Injuries to personnel. Damage to Banks man give proper hand Truck Pusher
to where load is to Truck hits personnel in equipments. signal. Good communication.
be loaded. Truck Pusher the area. One flag man only.
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Truck Pusher /
equipments Lifting equipment failure. equipments. Inspect all lifting gears for QSO
Truck Pusher damages.
3. Rig up load to Struck by crane hook Pinched hands and fingers. Use full body harness. Keep RAP / A/D / QSO
crane hook block. Caught by. Injuries to personnel. Damage to fingers and hands clear
RAP equipments. between block hook latch and
sling/shackle.
4. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Use tag line. Counter pull on Rigger / QSO
equipments. swing motion. Clear area
Crane Operator under suspended load.
5. Move out the Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck Pusher /
Truck Truck Driver / something. equipments. signal. Good communication. QSO
Truck Pusher One flag man only.
6. Set tanks on the Trap under load. Caught Injuries to personnel. Damage to Clear area under load. Keep Rigger / QSO
ground Rigger / Crane by or swing hit. Spill equipments. environmental feet and legs away from load.
Operator damage Spill kit
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Prepare Critical Rigger Wrong Crane position Injuries to personal, damage to Rigger raise proper critical Rigger
lifting plan. equipment lifting plan, discussed the plan
2. Position trucks Drive into equipment. Injuries to personnel. Damage to Rigger give proper hand Rigger / Truck
to where load is to Truck hits personnel in equipments. signal. Good communication. Pusher
Truck Pusher/
be off loaded. the area. One flag man only.
Rigger
3. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Truck Pusher /
equipments Lifting equipment failure. equipments. Inspect all lifting gears for QSO
Truck Pusher damages.
4. Rig up load to Struck by crane hook Pinched hands and fingers. Use full body harness. Keep Rigger / QSO
crane hook block. Caught by. Injuries to personnel. Damage to fingers and hands clear
Rigger equipments. between block hook latch and
sling/shackle.
5. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Use tag line. Counter pull on Rigger/ QSO
Rigger/ Crane equipments. swing motion. Clear area
Operator under suspended load.
6. Drive truck off Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck Pusher /
load. Truck Driver / something. equipments. signal. Good communication. QSO
Truck Pusher One flag man only.
7. Set load to Trap under load. Caught Injuries to personnel. Damage to Use tag line. Clear area under QSO/ Rigger
ground. Rigger / Crane by or swing hit. equipments. load. Keep feet and legs away
Operator from load.
9. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position trucks Drive into equipment. Injuries to personnel. Damage to Banks man give proper hand Truck Pusher /
to where load is to Truck hits personnel in equipments. signal. Good communication. Driver
be loaded. Truck Pusher the area. One flag man only.
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Truck Pusher /
equipments Lifting equipment failure. equipments. Inspect all lifting gears for QSO
Truck Pusher damages.
3. Rig up load to Struck by crane hook Pinched hands and fingers. Use full body harness. Keep RAP / A/D / QSO
crane hook block. Caught by. Injuries to personnel. Damage to fingers and hands clear
RA equipments. between block hook latch and
sling/shackle.
4. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Use tag line. Counter pull on QSO/ Rigger
Crane Operator/ equipments. swing motion. Clear area
Rigger under suspended load.
5. Move out the Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck Pusher /
Lowbed Truck Driver / something. equipments. signal. Good communication. QSO
Truck Pusher One flag man only.
6. Set tanks on the Trap under load. Caught Injuries to personnel. Damage to Clear area under load. Keep Rigger / QSO
ground Rigger / Crane by or swing hit. Spill equipments. environmental feet and legs away from load.
Operator damage Spill kit
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position trucks Drive into equipment. Injuries to personnel. Damage to Banks man give proper hand Truck Pusher
to where load is to Truck hits personnel in equipments. signal. Good communication.
be loaded. Truck Pusher the area. One flag man only.
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Truck Pusher /
equipments Lifting equipment failure. equipments. Inspect all lifting gears for QSO
Truck Pusher damages.
3. Rig up load to Struck by crane hook Pinched hands and fingers. Use full body harness. Keep Rigger/ QSO
crane hook block. Caught by. Injuries to personnel. Damage to fingers and hands clear
RAP equipments. between block hook latch and
sling/shackle.
4. Pick up Tanks. Load swing. Load Injuries to personnel. Damage to Clear area under suspended RAP / A/D /
Crane Operator/ Collapse. Spill equipment. spill load. Only rigger who gives Rigger
Rigger signals, Prepare Spill kit
5. Move out the Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck Pusher
Lowbed Truck Driver / something. equipments. signal. Good communication.
Truck Pusher One flag man only.
6. Set Tank on the Unbalanced tank. Injuries to personnel. Damage to Set pipe rack properly. Rigger/ QSO
Pipe Rack Rigger / Crane Dropped equipments. Unload Tank in balance
Operator position.
7. Remove lifting Pinch point, . Personal Injury Wear impact gloves . RAP / A/D / QSO
equipment. RAP
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position trucks Drive into equipment. Injuries to personnel. Damage to Banks man give proper hand Truck Pusher
to where load is to Truck hits personnel in equipments. signal. Good communication.
be loaded. Truck Pusher the area. One flag man only.
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Truck Pusher /
equipments Lifting equipment failure. equipments. Inspect all lifting gears for QSO
Truck Pusher damages.
3. Rig up load to Struck by crane hook Pinched hands and fingers. Use full body harness. Keep RAP / A/D / QSO
crane hook block. Caught by. Injuries to personnel. Damage to fingers and hands clear
RAP equipments. between block hook latch and
sling/shackle.
4. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Use tag line. Counter pull on Rigger / QSO
Rigger/ Crane equipments. swing motion. Clear area
Operator under suspended load.
5. Move out the Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck Pusher /
Truck Truck Driver / something. equipments. signal. Good communication. QSO
Truck Pusher One flag man only.
6. Set Hopper on Trap under load. Caught Injuries to personnel. Damage to Clear area under load. Keep Rigger / QSO
the ground Rigger / Crane by or swing hit. Spill equipments. environmental feet and legs away from load.
Operator damage Spill kit
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position trucks Drive into equipment. Injuries to personnel. Damage to Banks man give proper hand Truck Pusher
to where load is to Truck hits personnel in equipments. signal. Good communication.
be loaded. Truck Pusher the area. One flag man only.
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Truck Pusher /
equipments Lifting equipment failure. equipments. Inspect all lifting gears for QSO
Truck Pusher damages.
3. Rig up load to Struck by crane hook Pinched hands and fingers. Use full body harness. Keep RAP / A/D / QSO
crane hook block. Caught by. Injuries to personnel. Damage to fingers and hands clear
RAP equipments. between block hook latch and
sling/shackle.
4. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Use tag line. Counter pull on RAP / A/D / QSO
Rigger/Crane equipments. swing motion. Clear area
Operator under suspended load.
5. Move out the Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck Pusher /
Truck Truck Driver / something. equipments. signal. Good communication. QSO
Truck Pusher One flag man only.
6. Set koomy on Trap under load. Caught Injuries to personnel. Damage to Clear area under load. Keep Rigger / QSO
the ground Rigger / Crane by or swing hit. Spill equipments. environmental feet and legs away from load.
Operator damage Spill kit
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position trucks Drive into equipment. Injuries to personnel. Damage to Banks man give proper hand Truck Pusher
to where load is to Truck hits personnel in equipments. signal. Good communication.
be loaded. Truck Pusher the area. One flag man only.
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Truck Pusher /
equipments Lifting equipment failure. equipments. Inspect all lifting gears for QSO
Truck Pusher damages.
3. Rig up load to Struck by crane hook Pinched hands and fingers. Use full body harness. Keep RAP / A/D / QSO
crane hook block. Caught by. Injuries to personnel. Damage to fingers and hands clear
RAP equipments. between block hook latch and
sling/shackle.
4. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Use tag line. Counter pull on Rigger / QSO
Rigger/ Crane equipments. swing motion. Clear area
Operator under suspended load.
5. Move out the Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck Pusher /
Truck Truck Driver / something. equipments. signal. Good communication. QSO
Truck Pusher One flag man only.
6. Set tanks on the Trap under load. Caught Injuries to personnel. Damage to Clear area under load. Keep Rigger / QSO
ground Rigger / Crane by or swing hit. Spill equipments. environmental feet and legs away from load.
Operator damage Spill kit
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.
Page No :
3. Hook crane up to Roustabout Fall struck by crane Injuries. Fall Protection stay Crane /optr
load. Pusher block. alert. Roustabout
Pusher
4. Pick up load. Crane operator/ Load could shift Equipment damage & Use tag line, do not T/P, Rigger
Rigger swing or fall. injuries. stand under Crane/optr
suspended load,
5. Drive truck out from Truck driver/ Rain over or into Damage Equipment Spotter give T/P
under load. Truck Pusher something. Personal injuries. directions.
6. Set down load. Rigger & Crane Drop load, swinging Damage & injuries Tag line, don’t Rigger/ Crane
Operator loads pinch points. stand in line of fire operator
pinch point area.
Basic Steps Responsible for Hazard Identification Assessment Controls Responsible
“How to do the Job?” Step “What can go wrong?” “What can happen if it “How do we stop it for control
“Who Will do it?” goes wrong?” from going “Who will do it?”
wrong?”
7. Remove lifting Roustabout Fall Personal injuries Fall protection T/P &
Equipment. pusher Roustabout
pusher
8.
9.
10.
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with
my work and the remedial actions to be taken to eliminate, reduce or control hazards.
Crew’s Name & Signature
1. 5.
2. 6.
3. 7.
4. 8.
Rig No :
Job Safety Plan (JSP) Page No :
Basics Steps Responsible for Hazard Identification Assessment Controls Responsible for
“How to do the Job?” Step “What Can go wrong?” “What can happen if it goes wrong?” “How do we stop it from going Control
“Who will do it?” wrong?” “Who will do it?”
1. Position trucks Drive into equipment. Injuries to personnel. Damage to Banks man give proper hand Truck Pusher
to where load is to Truck hits personnel in equipments. signal. Good communication.
be loaded. Truck Pusher the area. One flag man only.
2. Inspect lifting Load drops to personnel. Injuries to personnel. Damage to Check for appropriate SWL. Truck Pusher /
equipments Lifting equipment failure. equipments. Inspect all lifting gears for QSO
Truck Pusher damages.
3. Rig up load to Struck by crane hook Pinched hands and fingers. Use full body harness. Keep RAP / A/D / QSO
crane hook block. Caught by. Injuries to personnel. Damage to fingers and hands clear
RAP equipments. between block hook latch and
sling/shackle.
4. Pick up load. Load swing. Load falls. Injuries to personnel. Damage to Use tag line. Counter pull on Rigger / QSO
Crane Operator/ equipments. swing motion. Clear area
Rigger under suspended load.
5. Move out the Ran over or hit Injuries to personnel. Damage to Banks man give proper hand Truck Pusher /
Truck Truck Driver / something. equipments. signal. Good communication. QSO
Truck Pusher One flag man only.
6. Set tanks on the Trap under load. Caught Injuries to personnel. Damage to Clear area under load. Keep Rigger / QSO
ground Rigger / Crane by or swing hit. Spill equipments. environmental feet and legs away from load.
Operator damage Spill kit
7. Remove lifting Slip, trip and falls. Personal Injury Wear full body harness. RAP / A/D / QSO
equipment. RAP Attach lanyard and secure
self from fall.
I had fully understood all the details in this Job Safety Plan (JSP) as discussed by my supervisor. I am fully aware of the hazards involved with my work and the
remedial actions to be taken to eliminate, reduce or control the hazards.