Professional Documents
Culture Documents
Bronze Angle Check: Ga Te, GL Ob E, AND Valves
Bronze Angle Check: Ga Te, GL Ob E, AND Valves
com
S T A N D A R D P R A C T I C E
SP-80
1997
Edition
BRONZE GA TE, GL OB E,
ANGLE A N D CHECK VALVES
http://slidepdf.com/reader/full/mss-sp-80 1/27
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
An MSSStandard Practice is intended as a basis for common practice by the manufacturer, the user,
and the general public. The existence of an MSS Standard Practice does not in itself preclude the
manufacture, sale, or use of products not conforming to the Standard Practice. Mandatory conform-
ance is established only by reference in a code, specification, sales contract, or public law, as
applicable.
Unless otherwise specifically noted in thisSS SP, any standard referred to herein is identified byhe date of
issue that was applicable to the referenced standard(s)at the date of issue of this MSS SP. (See AnnexC .
An y part of this standard may be quoted. Credit lines should read ‘Extracted ro m M S S SP-80, 1997, with
perm ission of the publisher, the Manufacturers Stand ardization Society.’ Repro duction prohib ited under
copyrigh t convention unless written perm ission is granted b y the Manufacturers Standa rdization Society of
the Valve and Fittings Industry, Inc.
Copyright O 1983 by
Manufacturers Standardization Society
of the
Valve and Fittings Industry, Inc.
Printed in U.S.A.
P r ev i o u s p a
http://slidepdf.com/reader/full/mss-sp-80 1 is b l a n k
2/27
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings
Licensed by Information Handling Services
~~ ~~
5/26/2018 MSS-SP-80-slidepdf.com
CONTENTS Page
PURPOSE ..................................................................................... 1 1
3. MATERIALS ........................................................................... 4
4 . DESIGN ............................................................................... 4
. ..........................................................................
6 TOLERANCE 3
7. INSPECTIONANDTESTING ........................................................... 3
TABLE 1 RESSURE-TEMPERATURE RATINGS .......................................... 3
2 IST OF MATERIAL SPECIFICATIONS ....................................... 5
3 INIMUMLENGTHANDDEPTHOFTHREAD ............................. 8
4 RONZE GATE VALVES IAMETER OF STEM .............. .............. 11
5 RONZE GLOBE AND ANGLE VALVES IAMETER OF STEM .............. 11
6 RONZE GATE VALVES IAMETER OF HANDWHEEL .................... 12
7 RONZE GLOBE AND ANGLE VALVES IAMETER OF HANDWHEEL ....... 12
8A HELL TEST HREADED AND SOLDER END VALVES ................... 13
.
8B HELL TEST LANGED END VALVES ................................... 13
9A EAT TEST HREADED AND SOLDER END VALVES ..... ............... 14
9B EAT TEST LANGED END VALVES .......... ....
..................... 14
Al RESSURE-TEMPERATURE LIMITATIONS ................................ 15
http://slidepdf.com/reader/full/mss-sp-80 ii 3/27
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings
Licensed by Information Handling Services
___
=
~ ~~
5/26/2018 N G L 1777
S T D - M S S S P - 8 0 - EMSS-SP-80 5 7 7 0 b 9 0 0500873 373
-slidepdf.com
a) TypeFig
(NRS) 1 B, Annex
olid Wedge:
B Non-Rising Stem a) Threaded Ends izes 1/8 through 3
http://slidepdf.com/reader/full/mss-sp-80 1 4/27
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
2.2 These ratings are the maximum allowable 2.5 The ratings given in Table 1 at 20°F to
non-shock pressures at the temperatures shown, l50,OF shall also apply at lower temperatures.
and allowablepressuresmaybe nterpolated Products that are to operate at low temperatures
between temperatures shown. shall conform to the rules of the applicable
codes under which theyre to be used.
2
http://slidepdf.com/reader/full/mss-sp-80
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings 5/27
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
50 80 14065 50 00
650 670
00 75 60 75 590
410
06 25 50 150
50 00 O0 350 30
bonnet joints.
http://slidepdf.com/reader/full/mss-sp-80 3 6/27
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings
Licensed by Information Handling Services
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
factured to this standard shallbemade from valves, shall have a minimum area of not less
materialsproducedunderecognized quality than the area of a circle having a diameter equa
control procedures. Recommendedmaterials to the nominal pipe size excepthat valves fitted
are listed in Table 2. with seat rings may reduce the passageway area
by the area of the seat ring driving lugs. The
valve shall be so designed that the stem and/or
3.2 Castings All castings shall be clean and
sound, without defects which will impair their wedge clear the waterway when he valve is fully
service. No plugging,welding, repairing or open.
impregnating is allowed.
4.2.2 Thelowpassagewayofbronzeglobe
and angle valves, v p e s 1 and 2, designed with
3.3 Users are cautioned against application integral seats nd when fully open, shall have an
with fluids which may react chemically withny
area at all points equal to the area of a circle
material used in these valves.In certain areas of
having a diameter equalo the nominal pipe size
the country, wherewater conditions are par-
except the area through the seat may be reduced
ticularly “aggressive”, piping components made
by the area of the disc guides.
from certain zinc-bearing copper-base alloys re
susceptible to a form of corrosion known as
4.2.3 The flowassageway area of bronze
dezincification. Consultation with the manufac-
globe and angle valves, Type 3, of the full flow
.turer is advised to determine suitability in cases
design, may be reduced by the area of the seat
of doubt.
ring driving lugs.
http://slidepdf.com/reader/full/mss-sp-80 4 7/27
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
il
Check 1&3 Nickel-Copper Alloy ASTM B140-C32000-NoteC)
1
I
~~
NoteKd) Notefd)
lobe isc &
Suitable for service specified in aragraph 2.6.
Non- Angle 2
Pressure-Temperature Ratings
Metallic
heck 2&4
http://slidepdf.com/reader/full/mss-sp-80 8/27
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
T
200,300 & 350
Copper-Nickel Alloy Copper-Nickel Alloy
Nickel-Copper Alloy Nickel-Copper Alloy
Gate 1-4 Stn. Stl. Alloy (250-500 BHN) Stn. Stl. Alloy (250-500 BHN)
300 Series Stn. Stl. Alloy-Note(h) 300 SeriesStn. Stl. Alloy-Note@)
Seat Note(d) Note@)
Rings Globe & Copper-Nickel Alloy Copper-Nickel Alloy
Angle 3 Nickel-Copper Alloy Nickel-Copper Alloy
I Stn. Stl. Alloy (400-500 BHN) Stn. Stl. Alloy (400-500BHN)
Check 1-4 300 Series Stn. Stl. Alloy-Notelhl 300 Series Stn. Stl. Alloy-Note(h)
Noterd) Note@)
ASTM B62-CS3600 ASTM B61 -C92200
Globe & 2
Disc Nut Angle ASTM B16-C36000
ASTM B150-C64200 ASTM B62-C83600
ASTM B16-C36000
Disc ASTM B371-C69700 ASTM B 50-C642OO
Locknut Check ,Note@) ASTM B371 -C69700
Note@)
ASTM B61-C92200 ASTM B61-C92200
ASTM B62-CS3600 ASTM B62-CS3600-Note 4
Gate 1-4 ASTM B98-C65100 ASTM B98-C65 100
ASTM B99-C65 00 ASTM B99-C65100
ASTM B148-C95600 ASTM B148-C95600
Stem ASTM B371 C69400 & C69700 ASTM B371-C69400& C69700
ASTM B584-CS6400& C87400 ASTM B584-CS6500& C87400
Globe & 1-3 ASTM B584-CS7500& C87600 ASTM B584-CS7500& C87600
Angle ASTM B21-C46400 & C47940 ASTM B21-C46400& C48200
ASTM B21-C48200 ASTM B505-C83600-Note(a)
ASTM B505-C83600 QQ-C-390-C86500
QQ-C-39O-C86500 & C92200 QQ-C-591-C65100
QQ-C-465-C61400 Note ( 4
QQ-C-591-C65100
Note 4
Hanger Check 3854 ASTM B62-C83600 ASTM B61-C92200
(Hinge) ASTM B584-C87600 ASTM B62-CS360q-Note 4
Stainless Steel Alloy ASTM B584437600
Note@) Note 4
Hanger Pin ASTM B150-C64200 ASTM B 150-C64200
(Hinge Pin) ASTM B16-C36000 ASTM B16-C36000
Side
st op Plug
Plug Check 3&4 ASTM B371
Copper Alloy -C69700 ASTM
Copper B371-C69700
Alloy
Washer Nickel-Copper Alloy Nickel-Copper Alloy
Stainless Steel Alloy Stainless Steel Alloy
ASTM B62-CS3600 ASTM B62-CS3600
ASTM B124-C37700 ASTM B124-C37700
Stuffing Box Gate ASTM B16-C36000 ASTM B16-C36000-Note(g)
Packing Box Globe & ASTM B584-CS6400& C84400 ASTM B584-CS6400
Angle , ASTM B282 Type I-Note (f) 4STM B584-C84400-Note(e)
OtherCopperAlloymaterialshaving 4STM B282 Q p e II-Note (f)
physical and corrosive properties equiv- OtherCopperAlloymaterialshaving
alent to those of the listed materials physical and corrosive properties equiv-
alent to those of the listed materials
6
http://slidepdf.com/reader/full/mss-sp-80 9/27
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
NOTES: (a) - ASTM B62-C83600, may be used in place of ASTM B61-C92200 for class 200, 300 and
350 valves providedhat a temperature limitation f 45WF is shown n the identification
plate.
(c) onnet, cap, disc and discholder, sizes 3/4 and smaller only. Union rings, sizes 318 and
smaller only.
(d) -Other materials having physical nd corrosion resistant properties equivalent to those of
the listed material.
(e) -For use in Class 200 valves with non-metallic discs when temperature limitation of the
disc is a maximumf 450 degreesF.
I I
g) or sizes 3/ 4 and smaller.
http://slidepdf.com/reader/full/mss-sp-80 10/27
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
4.3. Body and Bonnet 4.3.2.2 All threads shall be countersunk a dis-
tance not less than one-half the pitch of threads
4.3.1 Thebody-bonnet joint on bronzegate, at an angle of approximately 45 degrees. Coun-
globe and angle valves and the body-cap joint tersinking shall be concentric with
hreads.
on. bronzecheckvalvesmaybe nsidescrew,
screw-over, union ring or bolted construction. 4.3.2.3 The length of threads specified in
Table 3 shall be measured to include the coun-
4.3.2 Threaded Ends tersink or chamfer. The maximumallowable
variation in the alignment of threads of all open-
4.3.2.1 Threadedendbodiesmay havepoly- ings of threaded valves shall be 0.06 inches in 2
gon ends or may have rounded ends with ribs. inches.
Valves with threaded ends shall be threaded in
accordance with the requirements of ANSI/
ASME B1.20.1, Pipe Threads, General Purpose
(Inch).
,\X\\\\\\
RB
.88 1.20
http://slidepdf.com/reader/full/mss-sp-80 11/27
8
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
4.3.3Solder Joint Ends older joint ends 4.4.1.2Splitwedge and parallelseat double
shall be prepared in accordance with applicable disc) shall be so designed that on reaching the
requirements of ANSI B16.18. point of closure, thrust from the stem will cause
vided in gate, globe and angle valves; however, stem. Discs, plugsor disc holders of the slip-on
type shall e adequately guided or self-centering
repacking while the valve is pressurized is not
and shall be so constructed with relationo body
recommended.
and bonnet that when the,valve is fully opened
they will not slip off the stem.
4.4 Discs and Seat Rings
Disc holders for Valves l)pe 2 shall be designed
4.4.1Discs and SeatRings for BronzeGate to contain the periphery of the non-metallic dis
Valves in position.
4.4.1 1 Solid wedge discs shall be of one piece 4.4.2.2 The seatmayhave an expanded-in,
construction with disc guides. The stem cham- threaded-in or otherwise renewable seat ring or
ber ofthe NRS discs shall bepen at the bottom maybecast integral with the body at the
for proper drainage. manufacturer’s option.
http://slidepdf.com/reader/full/mss-sp-80 9 12/27
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
4.4.3 Discs and Seats for Bronze CheckValves 4.6 Packing Box and Packing Nut for Bronze
Gate Valves and Bronze Globe nd Angle Valves
4.4.3.1 Bronze heckvalves, m e s 1 and 2
shall have the disc or disc holder substantially 4.6.1 Packing box for Class 125 valves may be
guided to ensure proper seating. of gland ollower ype or packingnut ype.
Packing box for all other valves,sizes greater
4.4.3.2 Bronzecheckvalves, m e s 3 and 4 than 1/2, shallbeof the gland follower type.
shall have discand disc holder securely fastened The length of packing in contact with the stem
to the hanger or hinge,Theconnectionshall shall be t least one diameter of the stem passing
allowsufficientfreedom so that the discwill through it. The thread of the packing nut shall
properly seat by gravity. The joint shall swivel be of sufficient length to enable the nut to be
freely to allow uniform wear except that disc or threaded on to the packing box or bonnet at
disc holdersand hanger maybe integral in Class least two full threads when the full amount óf
packing s in place and the length of thread
125 valves. engagement between he packing box or bonnet
4.4.3.3 Discholders for Bronzecheckvalves, and the packing nut shall be sufficient for full
mpes 2 and 4 shallbedesigned to hold and travel of the gland.
support the non-metallic disc.
4.6.2 Stem Packing - tem packing shall be
4.4.3.4 The seatmayhave an expanded-in,
threaded-in or otherwise renewable seat ring or I braided, twisted, or formed ring typemade from
non-asbestos material, suitable for the pressure-
temperature ratings of the valve.
I
may be cast integral with the body at the
manufacturer‘s option.
4.7 Handwheels for Bronze Gate Valves, and
4.5 Stems for Bronze Gate Valves, and Bronze Bronze Globeand Angle Valves
Globe and Angle Valves
Handwheels smaller han 6-in. n diameter shall
Stems shall be threaded with either Acme form be of the non-heat design with a raised rim to
threads or 60” truncated “V” threads, so that protect the hands. Handwheels 6 in. in diameter
the valve will be opened when the handwheel is and larger ,may be f the plain rim type marked
rotated counter-clockwise. The handwheel end to show the direction of opening. The diameter
of the stem shall be a tapered square with its of the handwheel shallnot be less han shown in
greatestdiagonalapproximatelyequal to the Tables 6 and 7. Allhandwheelsshallhave at
diameter of the stem or it may be of the splined least three spokes.
http://slidepdf.com/reader/full/mss-sp-80 10 13/27
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings
COPYRIGHT
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
http://slidepdf.com/reader/full/mss-sp-80 11 14/27
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
1
1-1/4 O0 O0 .25 3.25
1-1/2 .25 S O .62 3.62
.62 .00 .00 4.00
-1/2 .38 .62 .62 4.62
o0 o0 .50 5.50
When irregular handwheels are furnished, the largest dimension of the shape shall be considered the
handwheel diameter,
I I
I
DIAMETER OF HANDWHEEL MINIMUM I
I
LASS PRESSURE I
J
5/26/2018 MSS-SP-80-slidepdf.com
I I
ABLE 8A HELL TEST
THREADED AND SOLDER ENDALVES
Pressure ir Water
lass WP psi psi
125 00 300 80
150 0 300 450
00 00 0 600
00 0 900
m( 4 o00 0 1500
350 o00 1500 80
(a) See Table1, Note e
1 TABLE8B - HELL TEST
FLANGEDEND VALVES
http://slidepdf.com/reader/full/mss-sp-80 16/27
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
I
ABLE 9B - EAT TEST
FLANGEDEND VALVES
.
. . ~
I
~~
14
http://slidepdf.com/reader/full/mss-sp-80 17/27
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
I ANNEXA I
STRENGTH OF SOLDER JOINTS
(This Annex is an integral part of this Standard Practice and placed after the main text for
convenience.)
Extracted from American National Standard - ANSI B16.18, Cast Copper Alloy Solder Joint
Pressure Fittings.
The maximum recommended pressure-temperature limitations for solder joints made with copper tube
and cast copper alloyittings, using representative commercial solders,re listed in he table below.
NOTE: F or working temperatures, inhe O F to -20 F range, it is recommended that a joint material melting
at or aboveO00 F be employed. dl
CAUTION: When solder joint valves are used,he rating will be he lowest value of Table or Table Al. Also
refer to Paragraph 2.4.
*orking Maximum
emperature Working Pressure
Joining I Size 1/4 hru ?ao I Size11/4 hru d(*) I Size 2 112 thru
I I
Material F0
p si psi psi
1O0 00 75 150
50-50
25 150 150 1O0
Tin-Lead
00 O0 0 75
Solder (b) ( e )
50 5 5 50
NOTES:
(a) Standard water tube sizes.
(b) ANSVASTM B32 Alloy Grade 50A.
C ) ANSVASTM B32 Alloy Grade 95TA.
(d) These joining materials are defined as brazing alloys by he American Welding Society.
( e ) The SafeDrinking Water Act Amendment f 1986 prohibits any solderwith a ead content in excess of 0.2%
for use on potable water systems.
http://slidepdf.com/reader/full/mss-sp-80 18/27
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve
15 and Fittings
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
A NNE X B
VALVE TYPES
This Annex s an integral part of this Standard Practice which is placed fter the main text or convenience.
http://slidepdf.com/reader/full/mss-sp-80 19/27
COPYRIGHT 16and Fittings
OPYRIGHT Manufacturers Standardization Society of the Valve
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
PART NAME
IDENTIFICATION PLATE
HANDWHEEL
4 STEM
5 PACKING NUT
6 GLAND
DOUBLE DISC
10 DISC WEDGE
11 BODY
Note: The valve sketchesherein are for the purpose
GATE VALVE of illustration and nomenclature nly. They do not GATE VALVE
6 TYPE 3 represent any manufacturer's product.
I ' TYPE 4
Figure B3 Figure B4
http://slidepdf.com/reader/full/mss-sp-80 20/27
COPYRIGHT 17and Fittings
OPYRIGHT Manufacturers Standardization Society of the Valve
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
\ I I
STEM & DISC
I
114 -112 VALVES
I I
PART NAME PART NAME
HANDWHEEL NUT HANDWHEEL NUT
IDENTIFICATION PLATE IDENTIFICATION PLATE
3 HANDWHEEL
4 STEM
5 PACKING NUT
6 GLAND
7 PACKING
I 8 BONNET
UNION RING 9 DISC HOLDER
10 DISC
11 DISC PLATE (not shown)
I 12 BODY 12 DISC NUT
5/26/2018 MSS-SP-80-slidepdf.com
PART NAME
IDENTIFICATION PLATE
4 STEM
5 PACKING NUT
v
6 GLAND
UNION RING
10 LOCKNUT
PART NAME
DISC
4 BODY
PART NAME
UNION R I N G
3 DISC
4 BODY
4
5
DISC HOLDER
DISC
DISC GUIDE NUT
I i C;
1 5
ISC HOLDER
UIDE NUT
THREADED-IN HUB
1
Note: The valve sketches herein are for the purpose
of illustration and nomenclatureonly. They do not
represent any manufact urer's product.
Horizontal
nd,Angle
ift Check Vertical
heck Lift
Composition to Metal Seat Composition to Metal Seat
http://slidepdf.com/reader/full/mss-sp-80 24/27
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings
21
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
PART NAME
1 CAP
2 STOP PLUG
3 SIDE PLUGS
4 HANGER PIN
5 HANGER
6 RETAINING RING
I 7 WASHER
a) Body of “ Y ” type
I
CHECK VALVE
TYPE 3
~~~ ~
Figure B 10
Note: The valve sketches herein re for the purpose
of illustration and nomenclature only. They do not
represent any manufacturer’s product .
PART NAME I
p l k ü 7 HANGER PIN
j
4 HANGER
5 DISC HOLDER
1
(a) Body of “Y” ype
’ designalsoacceptable
CHECK VALVE
TYPE 4
Figure B 1
http://slidepdf.com/reader/full/mss-sp-80
COPYRIGHT
OPYRIGHT Manufacturers Standardization Society of the Valve and Fittings 25/27
Licensed by Information Handling Services
5/26/2018 MSS-SP-80-slidepdf.com
I ANNEXC I
REFERENCE STANDARDS
This
Annex isan integral partof this Standard Practice which is placed after the main text
or convenience.
List of standards and pecifications referenced in thisStandard Practice show the year f approval.
ANSI/ASME B1.20.1-
hreads,
1992
ipe
eneral
urpose
Inch)
ANSIB16.18-1984CastCopperAlloySolder-JointPressureFittings
ASME B16.24-1991 Cast Copper Alloy Pipe Flanges, Class 150,300,400,600,900,1500, and 2500, and Flanged Fittings,
Class 150 and 300
ASTM Publications
MSS Publications
MSS SP-6-1996 Standard Finishes forContact Faces of PipeFlanges andConnecting-End Flanges ofValves and Fittings
MSSSP-25-1993StandardMarkingSystemorValves,Fittings,FlangesandUnions
Federal Specifications
astings
QQ-C-390
lloy
opper
opper-Aluminum
QQ-C-465
lloys
QQ-C-591 opper-Silicon,
opper-Zinc-Silicon & Copper-Nickel-Silicon
lloys
MSS Manufacturers Standardization Society of the Valve and Fittings Industry, Inc.
127 Park Street, N.E., Vienna, VA 22180
5/26/2018 MSS-SP-80
STD*MSS SP-80-ENG L L977-slidepdf.com =
5 7 7 O b 4 0 0500914 710
SP-111-1996
SP-112-1993 Gray-Iron and Ductil
Quality Standard for e-Iron Tapping
Evaluation Sleeves
ofCast Surface Finishes isual and Tactile Method. This SP must be sold with a
10-surface, three-dimensional Cast Surface Comparator,hich is a necessary part ofhe Standard. Additional
comparators may be old separately.
SP-113-1994 Connecting Joint between Tapping Machines and Tapping Valves
SP-114-1995 Corrosion Resistant Pipe Fittings, Threaded and Socket Welding, Class 150 nd 1000
SP-115-1995 Excess Flow Valvesor Natural Gas Service
SP-116-1996 Service Line Valves and Fittings for Drinking Water Systems
SP-117-1996 Bellows Seals for Globe and GateValves
SP-118-1996 Compact SteelGlobe Check Valves langed, Flangeless, Threaded Welding Ends (Chemical Petroleum
Refinery Service)
SP-119-1996 Belled End Socket Welding Fittings, Stainless Steelnd Copper Nickel
R-Year -
tandard
ear
ndicates reaffirmedubstantive
without
hange. Prices available
pon reque
A large numberof former MSS Practices have been approved by he ANSI or ANSI Standards, published by others. n order to maintain a single source f authoritativ
Infonnation, the MSS withdraws its Standard Practlces ln such cases.