Professional Documents
Culture Documents
PUHY-P144TNU-A (-BS) 208-230V Product Data Sheet
PUHY-P144TNU-A (-BS) 208-230V Product Data Sheet
Job Name:
System Reference: Date:
UNIT OPTION
□ Standard Model PUHY-P144TNU-A
□ Seacoast (BS) Model PUHY-P144TNU-A-BS
OUTDOOR VRF HEAT PUMP SYSTEM ACCESSORIES
□ Joint Kit for details see Pipe Accessories Submittal
□ Low Ambient Kit for details see Low Ambient Kit Submittal
□ Snow/Hail Guards Kit for details see Snow/Hail Guards Kit Submittal
□ Panel Heater Kit for details see Panel Heater Kit Submittal
Specifications Model Name
External Dimensions (H x W x D) In. (mm) 71-10/16 x 48-14/16 x 29-3/16 (1,818 x 1,240 x 740)
Electrical Power Requirements Voltage, Phase, Hertz 3-phase 3-wire 208-230 V ±10% 60 Hz
External Static Pressure In. WG Selectable; 0, 0.12, 0.24, 0.32 in.WG; factory set to 0 in.WG
High Pressure High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
Inverter Circuit
Protection Devices Over-current protection
(Comp. / Fan)
NOTES: 1. Harsh weather environments may demand performance enhancing equipment. Ask
Nominal cooling conditions (Test conditions are based on AHRI 1230) Indoor: 80°FD.B./67°FW.B. your Mitsubishi Electric representative for more details about your region
(26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.) 2. For details on extended cooling operation range down to -10° F DB, see Low Ambient Kit Submittal
Nominal heating conditions (Test conditions are based on AHRI 1230) Indoor: 70°FD.B. (21.1°CD.B.), 3. When applying product below -4°F, consult your design engineer for cold climate
Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.) application best practices, including the use of a backup source for heating
4. Unit will continue to operate in extended operating range, but capacity is not guaranteed
Specifications are subject to change without notice. © 2019 Mitsubishi Electric Trane HVAC US LLC. All rights reserved.
PUHY-P-T(S)NU-A, Y(S)NU-A
NOTES:
• Standard:
150
(5-15/16)
MEES18K089
85(3-3/8)
0000005103.BOOK
Note 1. Please refer to the next page for information regarding necessary
130(5-1/8)
spacing around the unit and foundation work.
SEACOAST PROTECTION
2. At brazing of pipes, wrap the refrigerant service valve
with wet cloth and keep the temperature of refrigerant
2×6-ø4.6(3/16) Hole
740(29-3/16)
36 ページ
(Make hole at the plastic fan guard service valve under 120°C(248°F).
for snow hood attachment)
<Snow hood attachment hole> 1204(47-7/16) 18(3/4)
18
(3/4) 1240(48-7/8)
150(5-15/16)
70(2-13/16)
303
Model:
(11-15/16)
Diameter
Model Refrigerant pipe Service valve
PUHY-P96, 120, 144TNU-A(-BS)
1818(71-5/8)
service valve Control box
2019年2月13日 水曜日 午後4時56分
1515(59-11/16)
in the case the unit is used in combination with
1 7 4 3 other outdoor units.
135(5-3/8)
129(5-1/8)
84(3-5/16)
144(5-11/16)
*3 Furthest piping length (OU from IU)≥90m
54(2-3/16)
*4 Furthest piping length (OU from IU)≥40m
• Sea Coast (BS): Salt Spray Test Method (JRA 9002) - no unusual rust development to 960 hours.
NO. Usage Specifications
132(5-1/4)
109
(4-5/16)
1 Front through hole 148(5-7/8) × 84(3-5/16) Knockout hole
54(2-3/16) 592(23-5/16) 54 125 148(5-7/8) 207(8-3/16) For pipes Bottom through hole
2 150(5-15/16) × 94(3-3/4) Knockout hole
90(3-9/16)
20(13/16) (2-3/16) (4-15/16) 256(10-1/8) Front through hole ø62.7(2-1/2) or ø34.5(1-3/8) Knockout hole
Rear view Left side view 20(13/16) Front view 3
4 Front through hole ø43.7(1-3/4) or ø22.2(7/8) Knockout hole
128(5-1/16) 150 216(8-9/16) For wires
• Anti-corrosion Protection: A coating treatment is applied to condenser coil for protection from air contaminants.
5 Bottom through hole ø65(2-9/16) Knockout hole
243(9-5/8) (5-15/16) 172(6-13/16) 6 Bottom through hole ø52(2-1/16) Knockout hole
160(6-5/16) 152(6) 7 Front through hole ø34(1-3/8) Knockout hole
For transmission cables Bottom through hole
29.5
181
166
79
(3-1/8)
(7-3/16)
2 (6-9/16)
94
8 6
(3-3/4)
Refrigerant
service valve
<liquid>
110(4-3/8)
681(678~684)
(740)(29-3/16)
Refrigerant
(Mounting pitch)
service valve
185(7-5/16)
<gas>
2×2-14(9/16)×20(13/16) Oval hole
90(3-9/16) 1060(41-3/4) 90(3-9/16)
29.5
(1-3/16) (26-13/16)(26-3/4~26-15/16) (1-3/16)
(Mounting pitch)
Bottom view
Unit: mm (in.)
Y-Series
36
PUHY-P144TNU-A (-BS) – DIMENSIONS